File name TH-50PHD5.pdf

ORDER NO. ITD0207015C0 D10 Canada:B07 Wide Plasma Display TH-50PHD5 TH-50PHW5 GPH5D2 Chassis SPECIFICATIONS Specifications 1 Power Source: AC120V 50/60Hz (UY/UZ version) AC220-240V 50/60Hz (Except UY/UZ version) model) 495 W 2.4W (stand-by condition) (UY/UZ version) 3.0W (stand-by condition) (Except UY/UZ version model) 0.9W (Power off condition) (UY/UZ version model) 1.7W (Power off condition) (Except UY/UZ version model) Power Consumption: Plasma Display panel: Contrast Ratio Screen size: Drive method AC type 50-inch, 16:9 aspect ratio 3000:1 1,106 mm (W)Ч622 mm (H) 1,269 mm (diagonal) No. of pixels 1,049,088 (1,366 (W)Ч768 (H)) [4,098Ч768 dots] Operating condition: 34 °F - 104 °F (0 °C - 40 °C) Temperature Humidity 20 % - 80 % Horizontal scanning frequency 15.6 - 110kHz Vertical scanning frequency 48 120Hz Connection terminals: AV Video in S-VIDEO IN (MINI DIN 4PIN) 1.0 Vp-p (75-ohm) Y: 1 Vp-p (75-ohm), C: 0.286 Vp-p (75-ohm) AUDIO IN 0.5 Vrms (high impedance) (RCA PIN JACK Ч 2) COMPONENT/ RGB Y/G 1.0 Vp-p/composite (75ohm) 0.7 Vp-p/non-composite (75 -ohm) PB /B PR /R 0.7 Vp-p (75-ohm) 0.7 Vp-p (75-ohm) 2 HD VD AUDIO IN (RCA PIN JACKЧ2) PC (HIGH-DENSITY D-SUB15PIN) 1.0 - 5.0 Vp-p (high impedance) 1.0 - 5.0 Vp-p (high impedance) 0.5 Vrms (high impedance) R,G,B/0.7 Vp-p (75-ohm) HD, VD/1.0 - 5.0 Vp-p (high impedance) AUDIO IN (M3 JACK) 0.5Vrms (high impedance) SERIAL EXTERNAL CONTROL TERMINAL (DSUB9PIN) SPEAKERS (External speakers) RS-232C COMPATIBLE 6 16W [8W+8W] (10% THD) Dimensions (WЧ 47.6" (1,210 mm)Ч28.5" (724mm)Ч HЧD): 3.9" (98 mm) Weight (Mass) approx. 94.8 Ibs (42.5 kg) (main unit only) approx. 104.9 Ibs (47.1kg) (with speakers) 1 1. Applicable signals 3 2. Safety Precautions 2.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed. 3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards. 2.1.1. Leakage Current Cold Check 4 1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to thechassis, the reading should be between 1M and 5.2M . When the exposed metal does not have a return path to the chassis, the reading must be . Figure 1 2.1.2. Leakage Current Hot Check (See Figure 1 .) 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5k , 10 watts resistor, in parallel with a 0.15 F capacitors, between each exposed metallic part on the set and a good earth ground such as