BENQ Q7C3(FP767) free download

File name BENQ Q7C3(FP767).pdf

BENQ LCD FP767-12 Q7C3 Spare Parts List P/N: 99.L9072.RBA/RBE ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 DESCRIPTION PCBA I/F BD Q7C3-12MS AU IC FLASH MTV312MV64 (AJ) PLCC4 IC LVDS/RSDS MVPRL-HN PQPF 160P IC EEPROM AT24C04N-10SI-2.7SON IC CMOS 74LVC14A SO-N 14P IC LR AME8815AEGT250 SOT-223 IC VR G950T65U SOT-223 PCBA SPS BD Q7C3-12MS PCBA CTRL BD Q7C3 LCDM 17" M170EN05 V8 Q7C3/AUO ASSY BZL T7032C Q7C3 (FP767-12) ASSY UC ABSHB T7032C Q7C3 ASSY COLUMN ABS T7032C Q7C3 ASSY BKT-MAIN Q7C3 AUSIP W/SPK CORD SVT #18*3C 10A125V US1.5M CORD H05VV-3G 10A250V EURO CTN B Q7C3/BENQ Q7C3 CSN L EPS Q7C3/PAINTING Q7C3 CSN R EPS Q7C3/PAINTING Q7C3 CABLE AUD PC99PT284C/PT577C BK CABLE SIGNAL 15/15P CORE*1 1.5M CD FP767-12/756-12MS Q7C3-12MS ASSY BASE ABS T7032C Q7C3 PART NO. LOCATION 55.L9001.021 71.31264.A03 U4 71.MVPRL.A0E U2 72.02404.N01 U3 73.07414.061 U1 74.08815.C3C U5 74.95065.03C 55.L9002.003 55.L9003.011 56.91L90.011 60.L9001.061 60.L9002.011 60.L9003.012 60.L9020.002 27.01818.051 27.02718.051 44.L9001.002 47.L9013.001 47.L9014.001 50.74405.501 50.L9005.501 53.L9003.001 60.L9004.012 * THIS PARTS LIST MAY BE SUBJECT TO CHANGE WITH PRIOR NOTICE BY CSD OF BENQ. Q7C3 LCD Monitor Service Guide Alignment Procedure 1. Alignment procedure (for function adjustment) A. Preparation: 1. 2. Setup input timing ICL-605, 32-Grays pattern. Setup unit and keep it warm up at least 30 minutes. B. Timing adjustment: 1. Enter factory setting area (press "LEFT", "EXIT" and then press "SOFTPOWER"). 2. Check the settings to following values: Contrast = 50 Brightness = 90 Volume = 30 OSD time = 20 Color = sRGB Language = English Then, turn off the monitor power. 3. Turn on power enter user area. C. Color balance adjustment: 1. Enter factory setting area (press "LEFT", "EXIT" and then press "SOFTPOWER"). 2. Setup input timing UVGA7, 4-Grays pattern. 3. Press "AUTO", waiting for press message. 4. Press "RIGHT" to Calibrate ADC. 5. Setup input timing ICL-605, 32 -Gray pattern. 6. Checking if the picture is no good, reject this monitor. D. Color adjustment: 1. Setup input timing ICL-605, white pattern. 2. Measure color temperature by Minolta CA-110 (or equivalent equipment). 3. Alignment the color temperature Bluish, Reddish & sRGB. The color temperature specification as follows: White Balance (Bluish, 9300K set on OSD) White Balance (Reddish, 5800K set on OSD) White Balance (sRGB, 6500K set on OSD) X+Y+X+Y+X+Y+0.283+(-) 0.03 0.297+(-) 0.03 0. 326+(-) 0.03 0. 342+(-) 0.03 0. 313+(-) 0.03 0. 329 +(-) 0.03 1 Q7C3 LCD Monitor Service Guide Alignment Procedure 4. Turns off the monitor power. E. Writing EDID file: 1. Setup a PC with DDC card. 2. Connect PC to monitor with a D-sub signal cable. 3. Please refer to the C212 for the correct EDID file. 4. Runs the writing program to write the EDID file into EEPROM for analog input, ie. 15-pin D-sub. 5. Read both EEPROM data and confirm it to match with the C212 document definition. 2 Q7C3 LCD Monitor Ser