Subject | Text |
kenwood radio | First, you should check all of your speakers and speaker wires for shorts and grounds. If they chec |
Re: Kenwood KAC 920 | [quote:b31c33ec8d="Anonymous"][quote:b31c33ec8d="mental"]schematic diagram fur the kac 9020 car amp. |
|
| Problem is the wattage of the soldering iron. 25 watts is simply not hot enough . On double-sided p |
How to protect and safeguard the audio-visual data carrier? | 1. The audio frequency disc
Now the audio carrier most possibly found in the library is the dis |
| Your going to need a soldering iron with a thin tip, .050 solder wick, heat sink compound, and solde |
| Larger connections and the ones that get hot may have a ring around them from constantly heating and |
| Only put the soldering iron on each cap for a few seconds and obviously remove it before you switch |
plates loose | Both of my plates are loose from the tip of the iron to almost the base of their attachment site. Is |
Bush ws6671sil - 11AK19Pro chassis - Help needed! | Hello!
First off, this site is probably the most useful electronic repair site I have come across. |
Philips 28PW9513 (MD2.22AA) | Hi,
I know this is an old set but it's all I have and can't afford a new one.
I had a problem |
| After plenty of sodding about and trying to correct this. I got my meny back! Wahoo!
All that nee |
| Hi carnik,
This damage is not so serious,You can change the bad flyback capacitors but to do this n |
| Yes the legs are still intact on the bottom of the capacitor, but there is next to no room to get a |
Replacing Q330 | You can use a standard soldering iron but make sure it has a fine tip. you will also need some fine |
27PT6441/37 Turn ON | I posted last week that I replaced the Thermistor and the set still had the 3-2-1 code and did not t |
| PT NO IS REP2964A-M PART IS DISCONTINUED FROM PANASONIC. ONLY CHANCES WILL BE SOMEBODY WITH A SCRAP |
I repaired my N3250w thanks to JRnTX | Read through a lot of posts. Seems power problems with the N3250w is either Caps. or Q7 & ZD4 . |
|
MN101C51FFA: microcontroller? Can somebody offer some help | Hi guys!
OK, so after I followed Al_Dodge_Bundy's advice (thanks again Mark!), I think that what |
| I have the same problem with this TV. I'm no electronics guru, but I can use a voltmeter and a sold |
| Solder up the verticle ic. Not cold joints, bad solder joints. Once and for all wave soldering sucks |
Toshiba LCD TV 42WLG66 turn it self off after 8-10 seconds | Hi there,
this is my first post on this forum, which is excellent as I can see...thanks to my frien |
I`m looking for a manual or scheme for a [b]Sony ss-fcrw150[ | I want to connect the subwoofer to a Kenwood KRF-V5560D receiver. On the backpannel of the subwoofer |
Soldering help needed., It don't flow right | I’ve made my first DIY PCB, I’m trying to solder Leds into the holes and I’m a complete newbe, I got |
| just been having a tinker with the soldering iron,and have managed to get power to the unit,it even |
old TV | Remove the back from the TV and with an air compressor, blow out all the dust that may have accumula |
White Lines at the top of the screen | It is electrolytic pump cap in Vertical Deflection circuit . I had same problem - just replaced it o |
Dead Technosonic LCD 1908 | Many thanks I had the same fault , I used the link to obtain the diodes which cost £10.75 deliv |
how lame a question can you get out here | if you cant find a place to buy those simple caps on your own then you need real help to put down th |
| [quote:c0b741a804="shawng"]I really don't know to much about recievers but I've allways fixed my own |
| Yes indeed, lead-tin solder should normally be used. The exception is if the laptop is so recent tha |