Recommended Probe Configurations for 1168A and 1169A Active Probes 01168-92006 c20140722 [2].pdf part of Agilent Recommended Probe Configurations for 1168A and 1169A Active Probes 01168-92006 c20140722 [2] Recommended Probe Configurations for 1168A and 1169A Active Probes 01168-92006 c20140722 [2].pdf, Agilent Recommended Probe Configurations for 1168A and 1169A Active Probes 01168-92006 c20140722 [2].pdf text manual preview

Text preview for : Recommended Probe Configurations for 1168A and 1169A Active Probes 01168-92006 c20140722 [2].pdf part of Agilent Recommended Probe Configurations for 1168A and 1169A Active Probes 01168-92006 c20140722 [2] Agilent Recommended Probe Configurations for 1168A and 1169A Active Probes 01168-92006 c20140722 [2].pdf

Back to : Recommended Probe Configu | Home

1168/9A InfiniiMax II Probes
Locate the User's Guide Probe Compatibility Connecting the Probe to the Infiniium Scope

Download the comprehensive 1168/9A 90000 X and Q Series (with N5442A adapter) To Connect To Disconnect
user's guide from the probe's product 1. With the lever in relaxed in position push the probe onto the BNC. Move and hold the lever at R
page on www.keysight.com. The user's
guide is also available in Keysight's Probe 90000A Series
and returns to
2. The lever moves towards the R (release) symbol. (release) and pull the probe from
the BNC.
Resource Center (PRC) which is available 3. Move the lever towards the symbol until snug.
at www.keysight.com/find/PRC. The PRC
86100C/D Series (with N1022A/B adapter)
is an application that runs on a PC, Mac,
or iOS device.
80000B Series

Recomended Probe Head Configurations (Listed in order of best performance)

1. Differential Solder-In 2. Differential Brower 3. SMA Probe Head 4. N5425A ZIF Head / N5426A ZIF Tip

BANDWIDTH BANDWIDTH N5382A BANDWIDTH BANDWIDTH
N5380B
]1169A: 12 GHz N5381A ]1169A: 12 GHz Differential Browser ]1169A: 12 GHz ]1169A: 12 GHz
SMA
]1168A: 10 GHz Solder-In ]1168A: 10 GHz ]1168A: 10 GHz ]1168A: 10 GHz
Differential
Head
01169-21304
01169-81301 0.005 inch N5425A
0.007 inch steel wire (2) ZIF Head
tin-plated
Probe either differential or N5426A ZIF Tip
nickle wire (2) Probe either differential or
single-ended signals ] Preserves scope channels for measuring
single-ended signals differential signals (vs. A-B).
] Best solder-in connection for differential and ] Best solder-in connection for differential and ] Inherent cable loss compensation. ] Very small fine-pitch targets.
single-ended signals. single-ended signals. ] Common mode termination voltage can be ] Low cost solder tips for probing multiple
] Lowest capacitance. ] Lowest capacitance. supplied. test points.
] Wires must be cut to proper lengths ] Wires must be cut to proper lengths ] Offset SMA cables adapt to variable spacing. ] Full BW.
(see user's guide). (see user's guide). ] Full BW. ] Slightly higher loading than solder-in head.
Additional Configurations

5. N2884A Fine Wire ZIF Tip 6. N5451A Long-Wire ZIF TIP (7 mm) 7. N5451A Long-Wire ZIF TIP (11 mm) 8. Differential Solder-In

BANDWIDTH N2884A ZIF Tip BANDWIDTH BANDWIDTH BANDWIDTH
E2677A
]1169A: 12 GHz ]0