Text preview for : SONY DCR-SR77E, SR87, SR87E SERVICE MANUAL LEVEL 2 VER 1.1 2009.01 REV-1 (9-852-637-32).pdf part of SONY DCR-SR87 SONY DCR-SR77E, SR87, SR87E
DIGITAL VIDEO CAMERA RECORDER.
SERVICE MANUAL VERSION 1.1 2009.01 REVISION-1
PART#(9-852-637-32)
Back to : SONY DCR-SR77E, SR87, SR8 | Home
DCR-SR77E/SR87/SR87E
SERVICE MANUAL LEVEL 2
US Model
Ver. 1.1 2009.01 Canadian Model
Revision History AEP Model
UK Model
Revised-1 North European Model
Replace the previously issued E Model
SERVICE MANUAL 9-852-637-31
with this Manual.
Chinese Model
Korea Model
Argentine Model
Brazilian Model
Tourist Model
Photo: DCR-SR87
Japanese Model
Link
SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS
SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST
· Precaution on Replacing the VC-554 Board
The components identified by Les composants identifiés par une
mark 0 or dotted line with marque 0 sont critiques pour la
mark 0 are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.
DIGITAL VIDEO CAMERA RECORDER
2009A0800-1
DCR-SR77E/SR87/SR87E_L2 © 2009.01
9-852-637-32 Sony EMCS Co. Published by Kohda TEC
These specifications are extracted from instruction manual of
DCR-SR77E/SR87E.
ENGLISH JAPANESE
SPECIFICATIONS
System Input/Output connectors AC Adaptor AC-L200C/AC-L200D
Signal format: PAL color, CCIR standards A/V Remote Connector: Video/audio output jack Power requirements: AC 100 V - 240 V, 50 Hz/60
Movie recording format USB jack: mini-AB Hz
Video: MPEG2-PS (DCR-SR77E: output only) Current consumption: 0.35 A - 0.18 A
Audio: Dolby Digital 2ch/5.1ch Dolby Digital Power consumption: 18 W
5.1 Creator LCD screen Output voltage: DC 8.4 V*1
Photo file format Picture: 6.7 cm (2.7 type, aspect ratio 16:9) Operating temperature: 0 °C to 40 °C (32 °F to
: DCF Ver.2.0 Compatible Total number of pixels: 123 200 (560 × 220) 104 °F)
: Exif Ver.2.21 Compatible Storage temperature: -20 °C to +60 °C (-4 °F to
: MPF Baseline Compatible +140 °F)
General
Recording media (Movie/Photo) Dimensions (approx.): 48 × 29 × 81 mm (1 15/16
Power requirements: DC 6.8 V/7.2 V (battery
Hard disk: 80 GB × 1 3/16 × 3 1/4 in.) (w/h/d) excluding the
pack) DC 8.4 V (AC Adaptor)
"Memory Stick PRO Duo" media projecting parts
Average power consumption: During camera
When measureing media capacity, 1 GB Mass (approx.): 170 g (6.0 oz) excluding the
recording, using LCD screen at normal
equals 1 billion bytes, a portion of which is power cord (mains lead)
brightness:
used for data management. *1 See the label on the AC Adaptor for other
Internal hard disc: 2.5 W
Image device specifications.
"Memory Stick PRO Duo" media: 2.3 W
3.0 mm (1/6 type) CCD (Charge Coupled
Operating temperature: 0 °C to 40 °C (32 °F to
Device) Rechargeable battery pack
104 °F)
Gross: Approx. 1 070 000 pixels
Storage temperature: -20 °C to +60 °C (-4 °F to NP-FH50
Effective (Movie, 16:9): Approx. 670 000
+140 °F) Maximum output voltage: DC 8.4 V
pixels
Dimensions (approx.) Output voltage: DC 6.8 V
Effective (Photos, 16:9): Approx. 750 000
60 × 68 × 105 mm (2 3/8 × 2 3/4 × 4 1/4 in.) Maximum charge voltage: DC 8.4 V
pixels
(w/h/d) including the projecting parts Maximum charge current: 1.75 A
Effective (Photos, 4:3): Approx. 1 000 000
60 × 68 × 112 mm (2 3/8 × 2 3/4 × 4 1/2 Capacity: 6.1 Wh (900 mAh)
pixels
in.) (w/h/d) including the projecting parts, Type: Li-ion
Lens
and the supplied rechargeable battery pack
Carl Zeiss Vario-Tessar
attached Design and specifications of your camcorder and
25×(Optical), 50×, 2 000×(Digital)
Mass (approx.) accessories are subject to change without notice.
Filter diameter: 30 mm (1 3/16 in.)
300 g (10 oz) main unit only
Focal length
350 g (12 oz) including the supplied
F=1.8 ~ 3.2
rechargeable battery pack
f=2.5 ~ 62.5 mm (1/8 ~ 2 1/2 in.)
When converted to a 35 mm still camera
For movies: 41 ~ 1 189 mm (1 5/8 ~ 46 7/8
in.) (16:9)*
For photos: 36 ~ 900 mm (1 7/16 ~ 35 1/2
in.) (4:3)
Color temperature: [AUTO], [ONE PUSH],
[INDOOR] (3 200 K), [OUTDOOR] (5 800
K)
Minimum illumination
8 lx (lux) ([AUTO SLW SHUTTR] is set to
[ON], shutter speed 1/25 second)
* The focal length figures are actual figures
resulting from wide angle pixel readout.
DCR-SR77E/SR87/SR87E_L2
--2--
These specifications are extracted from instruction manual of
DCR-SR87.
ENGLISH JAPANESE
SPECIFICATIONS
System Input/Output connectors AC Adaptor AC-L200C/AC-L200D
Signal format: NTSC color, EIA standards A/V Remote Connector: Video/audio output jack Power requirements: AC 100 V - 240 V, 50 Hz/60
Movie recording format USB jack: mini-AB Hz
Video: MPEG2-PS Current consumption: 0.35 A - 0.18 A
Audio: Dolby Digital 2ch/5.1ch Dolby Digital LCD screen Power consumption: 18 W
5.1 Creator Picture: 6.7 cm (2.7 type, aspect ratio 16:9) Output voltage: DC 8.4 V*1
Photo file format Total number of pixels: 123 200 (560 × 220) Operating temperature: 0 °C to 40 °C (32 °F to
: DCF Ver.2.0 Compatible 104 °F)
: Exif Ver.2.21 Compatible General Storage temperature: -20 °C to +60 °C (-4 °F to
: MPF Baseline Compatible Power requirements: DC 6.8 V/7.2 V (battery +140 °F)
Recording media (Movie/Photo) pack) DC 8.4 V (AC Adaptor) Dimensions (approx.): 48 × 29 × 81 mm (1 15/16
Hard disk: 80 GB Average power consumption: During camera × 1 3/16 × 3 1/4 in.) (w/h/d) excluding the
"Memory Stick PRO Duo" media recording, using LCD screen at normal projecting parts
When measureing media capacity, 1 GB brightness: Mass (approx.): 170 g (6.0 oz) excluding the
equals 1 billion bytes, a portion of which is Internal hard disc: 2.5 W power cord (mains lead)
used for data management. "Memory Stick PRO Duo" media: 2.3 W *1 See the label on the AC Adaptor for other
Image device Operating temperature: 0 °C to 40 °C (32 °F to specifications.
3.0 mm (1/6 type) CCD (Charge Coupled 104 °F)
Device) Storage temperature: -20 °C to +60 °C (-4 °F to Rechargeable battery pack
Gross: Approx. 1 070 000 pixels +140 °F) NP-FH50
Effective (Movie, 16:9): Approx. 670 000 Dimensions (approx.) Maximum output voltage: DC 8.4 V
pixels 60 × 68 × 105 mm (2 3/8 × 2 3/4 × 4 1/4 in.) Output voltage: DC 6.8 V
Effective (Photos, 16:9): Approx. 750 000 (w/h/d) including the projecting parts Maximum charge voltage: DC 8.4 V
pixels 60 × 68 × 112 mm (2 3/8 × 2 3/4 × 4 1/2 Maximum charge current: 1.75 A
Effective (Photos, 4:3): Approx. 1 000 000 in.) (w/h/d) including the projecting parts, Capacity: 6.1 Wh (900 mAh)
pixels and the supplied rechargeable battery pack Type: Li-ion
Lens attached
Carl Zeiss Vario-Tessar Mass (approx.) Design and specifications of your camcorder and
25×(Optical), 50×, 2 000×(Digital) 300 g (10 oz) main unit only accessories are subject to change without notice.
Filter diameter: 30 mm (1 3/16 in.) 350 g (12 oz) including the supplied
Focal length rechargeable battery pack
F=1.8 ~ 3.2
f=2.5 ~ 62.5 mm (1/8 ~ 2 1/2 in.)
When converted to a 35 mm still camera
For movies: 41 ~ 1 189 mm (1 5/8 ~ 46 7/8
in.) (16:9)*
For photos: 36 ~ 900 mm (1 7/16 ~ 35 1/2
in.) (4:3)
Color temperature: [AUTO], [ONE PUSH],
[INDOOR] (3 200 K), [OUTDOOR] (5 800
K)
Minimum illumination
8 lx (lux) ([AUTO SLW SHUTTR] is set to
[ON], shutter speed 1/30 second)
* The focal length figures are actual figures
resulting from wide angle pixel readout.
DCR-SR77E/SR87/SR87E_L2
--3--
ENGLISH JAPANESE
NTSCJ·[·A EIA·W··ûZ® DC 6.8 V/7.2 V
DC'[Zq"ü--Í DC 8.4 V
rfI f`oe·F MPEG2-PS ·Á"ï"d--Í·Ft·»æÊZg--pZz·A¾,é,³·W··F
¹·º·F Dolby Digital 2ch/5.1chh ^< 5.1NSG·[^·["<·Ú ·g·,S·[XeBbN PRO f...I·h·F 2.3 W
·ÃZ~æt@C ·F DCF Ver2.0·<'
·Û`¶·"x·F·| 20·Z·` +60·Z
·F Exif Ver2.21·<'
·F MPF Baseline·<' SOOE`·¡@·F 60·~ 68·~ 105 mm
·i"Ë 60·~ 68·~ 112 mm
n·[hfBXN 80GB
·i"Ë ·g·,S·[XeBbN PRO f...I·h
·i···~·,,³·~oe·s,«·j
--e--Ê,Í·A 1GB,ð 10-oCg,ÅOEvZZ,µ,½·ê·,Ì·"
'l,Å,··B {`ÌZ¿--Ê·F
,Ü,½SÇ--·--pt@C<,È,Ç,ðSÜ,Þ,½,ß·AZÀ·Û,ÉZg ñ 300 g·i{`Ì,Ì,Ý·j
--p,Å,«,é--e--Ê,ÍZáS±OE¸·-,·,é·ê·,ª, ,è,Ü,··B ZBeZz`·Z¿--Ê·F
ZB`oe`fZq·F 3.0 mm·i 1/6OE^·j CCDOEÅ`ÌZB`oe`fZq ñ 350 g·i·t`®obeS·[SÜ,Þ·B·j
`·æ`f·"·Fñ 107oeæ`f
"®æZz--LOEøæ`f·"·i 16·F 9·j·Fñ 67oeæ`f
·ÃZ~æZz--LOEøæ`f·"·i 16·F 9·j·Fñ 75oeæ`f
AC 100 V - 240 V·A50 Hz/60 Hz
·ÃZ~æZz--LOEøæ`f·"·i 4·F 3·j·Fñ 100oeæ`f
·Á"ï"d--Í·F 18 W
Y·[OE"Y·FJ·[ 25"{·iOEõSw·j·A 50"{·A 2 000"{·ifW^<·j 'èSi·o--Í·F DC 8.4 V*
tB<^·[OEa 30 mm "®·ì·"x·F 0 ·Z·` 40 ·Z
F1.8·` 3.2
f=2.5·` 62.5 mm ·Û`¶·"x·F·| 20 ·Z·` +60 ·Z
35mmJ·S·ZZ,Å,Í SOOE`·¡@·Fñ 48·~ 29·~ 81 mm·i·Å`å"Ë "®æZBeZz·F ,-·j·i···~·,,³·~oe·s,«·j
41 ·` 1 189 mm·i 16·F 9·j *
·ÃZ~æZBeZz·F Z¿--Ê·Fñ 170 g·i{`Ì,Ì,Ý·j
36·` 900 mm·i 4·F 3·j * ,»,Ì`¼,ÌZd--l,É,Â,¢,Ä,Í ACA_v^·[,Ìx<,ð
·F·"x·Ø,èS·,¦·F·mI·[g·n·A·m·"vbV...·n·A·m®"à·n ,²----,-,¾,³,¢·B
·i 3 200 K·j·A·m®SO·n·i 5 800 K·j
·Å'á"íZÊ`Ì·Æ"x·F 8 lx·i ^·n·m"ü·n·AVb^·[Xs·[h 1/30·b·j
DC 8.4 V
* ·LSpæ`f"Ç,Ý·o,µ,É,æ,éZÀ"®·ì'l
OEö·Ì"d^³·F DC 6.8 V
--e--Ê·F 6.1 Wh·i 900 mAh·j
A/VS,·[g'[Zq·Ff`oe¹·º·o--Í'[Zq Zg--p"d'r·F Li-ion
USB'[Zq·F mini-AB {<@,âANZTS·[,ÌZd--l,¨,æ,ÑSOSÏ,Í·Aü--Ç,Ì,½,ß
--\··,È,-·Ï·X,·,é,±,Æ,ª, ,è,Ü,·,ª·A,²--¹·³,-,¾,³,¢·B
6.7 cm·i 2.7OE^·AAXyNg"ä 16·F 9·j
`·hbg·"·F 123 200hbg
¡ 560·~·c 220
DCR-SR77E/SR87/SR87E_L2
--4--
Model information table
Model DCR-SR77E DCR-SR87 DCR-SR87E
US, CND, AR,
Destination AEP, UK NE, CH, E, JE
KR, E, BR, JE, J
Color system PAL NTSC PAL
Data CAM PC
copy CAM PC
· Abbreviation
AR : Argentine model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
KR : Korea model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-CX11E/CX12/CX12E_L2
--5--
ENGLISH JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
2. Check the interboard wiring to ensure that no wires are
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
: LEAD FREE MARK
transistors, that were installed during a previous repair. Point
Unleaded solder has the following characteristics.
them out to the customer and recommend their replacement. · Unleaded solder melts at a temperature about 40°C higher than
4. Look for parts which, through functioning, show obvious signs ordinary solder.
of deterioration. Point them out to the customer and Ordinary soldering irons can be used but the iron tip has to be
recommend their replacement. applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350°C.
· Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
· Strong viscosity
· Do not touch the soldering iron on the same conductor of the
Unleaded solder is more viscous (sticky, less prone to flow) than
circuit board (within 3 times). ordinary solder so use caution not to let solder bridges occur such
· Be careful not to apply force on the conductor when soldering as on IC pins, etc.
or unsoldering. · Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
DCR-SR77E/SR87/SR87E_L2
--6--
ENGLISH JAPANESE
1. 6.
· 270
·
·
2. 7.
Lead Free
0
3.
· 40
4. 350
·
5. IC
·
· ·
DCR-SR77E/SR87/SR87E_L2
--7--
1. SERVICE NOTE ENGLISH JAPANESE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200C/L200D).
1-2. PRECAUTION ON REPLACING THE VC-554 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the "DESTINATON DATA WRITE".
RESTORE DATA
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform "RESTORE DATA" to get the data.
The data getting for this model is as follows.
· USB SERIAL No.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the "USB SERIAL No. INPUT".
1-3. USING SERVICE JIG
Connect the extension cable (J-6082-698-A) between CN1111 on the DA-044 board and CN1014 on the VC-554 board.
DA-044 board (side B)
CN1111
Extension cable (100P)
(J-6082-698-A)
CN1014
VC-554 board (side B)
DCR-SR77E/SR87/SR87E_L2
1-1
ENGLISH JAPANESE
1-4. SELF-DIAGNOSIS FUNCTION
1-4-1. Self-diagnosis Function 1-4-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the counter of the
function starts working, and displays on the LCD screen what to LCD screen shows a 4-digit display consisting of an alphabet and
do. numbers, which blinks at 3.2 Hz. This 5-character display indicates
Details of the self-diagnosis functions are provided in the Instruction the "repaired by:", "block" in which the problem occurred, and
manual. "detailed code" of the problem.
LCD screen
C:31:11
Blinks at 3.2 Hz
C 31 11
Repaired by: Block Detailed Code
C : Corrected by customer Indicates the appropriate Refer to "1-4-3. Self-diagnosis Code Table".
H : Corrected by dealer step to be taken.
E : Corrected by service E.g.
engineer 31 ....Reload the tape.
32 ....Turn on power again.
DCR-SR77E/SR87/SR87E_L2
1-2
ENGLISH JAPANESE
1-4-3. Self-diagnosis Code Table
Self-diagnosis Code
Repaired by:
Block Detailed Symptom/State Correction
Function Code
C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.
"Memory Stick Duo" is unformatted. Format the "Memory Stick Duo".
C 1 3 0 1
"Memory Stick Duo" is broken. Insert a new "Memory Stick Duo".
Remove the power source. Reconnect it again and operate your
C 1 3 0 2 Disc access error
camcorder again
E 2 0 0 0 Flash memory data are rewritten. Make flash memory data correct value. (Note 1)
E 3 1 0 0 Drive fault Inspect or replacement of the hard disc drive.
Inspect the lens block focus reset sensor (pin 7 of CN5101 on
the VC-554 board) when focusing is performed when the focus
Difficult to adjust focus
E 6 1 0 0 buttons of the touch panel are pressed in the focus manual mode,
(Cannot initialize focus.)
and the focus motor drive circuit (IC5301 on the VC-554 board)
when the focusing is not performed.
Inspect the lens block zoom reset sensor (pin qa of CN5101 on
Zoom operations fault the VC-554 board) when zooming is performed when the zoom
E 6 1 1 0 lever is operated, and the zoom motor drive circuit (IC5301 on
(Cannot initialize zoom lens.)
the VC-554 board) when zooming is not performed.
The abnormalities in initialization of Check whether the flexible board of the lens is broken, and
the focus lens and the abnormalities in check whether it is inserted imperfectly. If there is no problem in
E 6 1 1 1
initialization of the zoom lens occurred the flexible board, inspect the focus/zoom motor drive circuit
simultaneously. (IC5301 on the VC-554 board).
Handshake correction function does not
Inspect PITCH angular velocity sensors (SE7002 on the CD-
E 6 2 0 0 work well. (With PITCH angular
672/CD-687 board) peripheral circuits.
velocity sensor output stopped.)
Handshake correction function does not
Inspect YAW angular velocity sensors (SE7001 on the CD-672/
E 6 2 0 1 work well. (With YAW angular velocity
CD-687 board) peripheral circuits.
sensor output stopped.)
Fault of writing to or erasing the flash
E 9 4 0 0 Inspect the flash memory (IC7801 on the VC-554 board). (Note 1)
memory
Note 1: Start the Adjust Manual in the Adjust Station and refer to the "DESTINATON DATA WRITE".
DCR-SR77E/SR87/SR87E_L2
1-3
1. SERVICE NOTE ENGLISH JAPANESE
DA-044Sî"Â (BÊ`¤ )
CN1111
,,'·P·[u< (100P)
(J-6082-698-A)
CN1014
VC-554Sî"Â (BÊ`¤ )
DCR-SR77E/SR87/SR87E_L2
1-4
ENGLISH JAPANESE
C:31:11
C 31 11
DCR-SR77E/SR87/SR87E_L2
1-5
ENGLISH JAPANESE
C 0 4 0 0
C 1 3 0 1
C 1 3 0 2
E 2 0 0 0
E 3 1 0 0
E 6 1 0 0
7
E 6 1 1 0
qa
E 6 1 1 1
E 6 2 0 0
E 6 2 0 1
E 9 4 0 0
DCR-SR77E/SR87/SR87E_L2
1-6E
2. DISASSEMBLY
NOTE FOR REPAIR
· Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt
Do not insert the cable insufficiently nor crookedly. which comes off at the point.
(Be careful or some
· When remove a connector, don't pull at wire of connector. It is possible that a wire is snapped. pieces of gilt may be left inside)
· When installing a connector, don't press down at wire of connector.
It is possible that a wire is snapped.
DCR-SR77E/SR87/SR87E_L2
2-1
2-1. IDENTIFYING PARTS
Top Cabinet Assy
Microphone Assy
HDD Lid BT Block Assy
HDD
Main/Lens Section
VC-554 Board
DA-044 Board
F Panel Assy MS-413 Board
CD-672/CD-687 Board
FP-1061 Flexible Board
FP-1063 Flexible Board
Cabinet R Section
- DISASSEMBLY FLOW - CK-209 Board
OC-015 Board
2-2-1. HDD SECTION
PD-378 Board
Top Cabinet Assy
FP-1062 Flexible Board
HDD
HDD Holder
2-2-2. OVERALL SECTION-1
F Panel Assy
Microphone Assy
2-2-3. OVERALL SECTION-2 2-2-5. CABINET R SECTION
Cabinet R Section CK-209 Board
BT Block Assy
2-2-4. MAIN/LENS SECTION 2-2-6. LCD Section
Lens Block Cabinet (R) Assy
VC-554 Board LCD
DA-044 Board
DCR-SR77E/SR87/SR87E_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW HARDWARE LIST
2-2-1. HDD SECTION
Follow the disassembly in the numerical order given.
1 Top Cabinet Assy (1-1 to 1-7)
2 HDD (2-1 to 2-3)
3 HDD Holder (3-1 to 3-3)
1-1 (#2) 1-4
1 Top Cabinet Assy
1-3
2-2
(Claws)
2 HDD
HELP01
2-1
3-1
1-7E (#2)
3-2
1-2 (#2) (#2)
2-3E
1-6 (#2)
Note: In case of attaching,
turn the concave portion 3-3E
to the HDD holder side.
HELP01
3 HDD Holder
Overall Section-1 1-5 (Open)
(See Page 2-4)
DCR-SR77E/SR87/SR87E_L2
2-3
2-2-2. OVERALL SECTION-1
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 F Panel Assy (1-1 to 1-7)
2 Microphone Assy (2-1 to 2-3)
2 Microphone Assy
HELP02
2-1 2-3E
(#2)
1-6
(#9)
1-4 (#2) 2-2
HELP03
1 F Panel Assy
1-7E
(Boss) 1-5 (#2) Overall Section-2
1-3 1-1 (#2) (See Page 2-5)
1-2
DCR-SR77E/SR87/SR87E_L2
2-4
2-2-3. OVERALL SECTION-2
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Cabinet R Section (1-1 to 1-8)
2 BT Block Assy (2-1 to 2-6)
2-4 (Boss)
HELP05
2-3 (#2)
2 BT Block Assy
Main/Lens Section
(See Page 2-6) 2-5 (Boss)
2-2 (#2)
2-1
2-6E
HELP04
1-1 (#2)
1-5 (Boss)
1-6 (Claw)
1-7
1-8E
1-2 (#2)
1-4 (Boss)
1-3 (#2)
1 Cabinet R Section
(See Page 2-7)
DCR-SR77E/SR87/SR87E_L2
2-5
2-2-4. MAIN/LENS SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Lens Block (1-1 to 1-3)
2 VC-554 Board (2-1 to 2-3)
3 DA-044 Board (3-1 to 3-5)
Note: When installing Lens Block,
confirm the NS knob of lens
turns off.
3-2
1-3E (#11)
CD
-67
2
HELP06
2-3E
B 2 VC-554
2-1 (#3) Board B
A
4
4
55
--55
1-2
VC
VC 2-2
(Connector)
3-3 (#3)
4
04 1 Lens Block
3 DA-044 DA- A 1-1
Board
3-1 (#3)
3
- 41
MS
3-4
3-5E
DCR-SR77E/SR87/SR87E_L2
2-6
2-2-5. CABINET R SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 CK-209 Board (1-1 to 1-11)
1-4 1-3 (#2)
1 CK-209 Board
HELP08 1-2
1-1
1-5 (#3)
1-8
(Solders) 1-9
HELP07
1-6
(#3)
1-10
1-11E (Solders)
HELP07
1-7
(#3)
LCD Section
(See Page 2-8)
DCR-SR77E/SR87/SR87E_L2
2-7
2-2-6. LCD SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Cabinet (R) Assy (1-1 to 1-6)
2 LCD (2-1 to 2-7)
1 Cabinet (R) Assy
1-6E
HELP09
2-7E
A
B
B
2-3
2-4 (#12)
1-1 (#2)
PD 2-2
A -37 2-1
8 2 LCD
2-5
(Claws)
1-2
1-4 (Claws)
1-3 (Claws)
2-6
1-5
DCR-SR77E/SR87/SR87E_L2
2-8E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP01
GASKET (OG) PUTTING POSITION
Apply metal portions.
Gasket (OG)
HELP02
TAPE (A) PUTTING POSITION
Flexible Board
(Microphone Unit (MIC901))
Main Frame Tape (A)
Edge of
Main Frame
DCR-SR77E/SR87/SR87E_L2
HELP
HELP03
GASKET (YB) PUTTING POSITION
Gasket (YB)
Outline of bending portion
DCR-SR77E/SR87/SR87E_L2
HELP
HELP04
ROUTING DC JACK HARNESS
1 Arrange DC Jack Harness in the arrow direction. 2 Secure DC Jack Harness with Tape (A).
DC Jack harness Bending
portion of
metal plate
Tape (A)
Arrange DC Jack harness Arrange the harness from
in the arrow direction. the Lib A to upward. Lib A
Arrange it within
Do not touch the width of Lib B.
3 Crease the harness to match
the moving
the connector with Lib A position. parts and
do not cover
with the the
Creasing position tape (A).
Lib B
Connector
Lib A
Do not press
forcefully.
Note on assembling BT Block Assy
to the body
BT Block Assy
Arrange the harness not
out of the cabinet (R) side.
Arrange the harness not
out of the cabinet (R) side
from the printed circuit board.
DCR-SR77E/SR87/SR87E_L2
HELP
HELP05
PS ADHESIVE SHEET PUTTING POSITION
Edge of the Wall Surface
PS Adhesive Sheet
Printed Area
HELP06
HOW TO ATTACHING THE BUS (HDD) TO THE FP-1063 FLEXIBLE BOARD
FP-1063 Adjusting position
Flexible Board
Bus (HDD)
Pattern Side
DCR-SR77E/SR87/SR87E_L2
HELP
HELP07
SOLDERING POSITION OF HARNESSES (HARNESS HN-024/HN-079/HN-080/HN-081)
Harness (HN-024) Speaker (1.6cm)
(Gray)
CK-209 Board
Harness (HN-080)
(Red)
Harness (HN-081)
(Black) OC-015 Board
Harness (HN-079)
(Gray)
HELP08
ROUTING HARNESSES AND FLEXIBLE BOARDS OF CABINET R SECTION
Speaker (1.6cm)
Lib
Harness (HN-024)
(Gray)
Speaker Holder
Harness (HN-080) (Red)
Harness (HN-079) (Gray)
Harness (HN-081) (Black)
Lib FP-1062 Flexible Board
Tape (A)
Flexible Flat Cable (FFC-185)
DCR-SR77E/SR87/SR87E_L2
HELP
HELP09
THE METHOD OF ATTACHMENT OF FP-1062 FLEXIBLE BOARD
1 Fold dotted line parts of the FP-1062 flexible board
as shown in figure.
Valley fold
Adhesive tape
Mountain
fold
Adhesive tape
Valley fold
Mountain fold
Stick it together in the adhesive tape
while bending the FP-1062 flexible board.
2 Install FP-1062 flexible board 3 Install the Hinge Cover (C).
in the Hinge Cover (M).
FP-1062 Claw
flexible board
Adhesive tape Claws
Hinge Cover (M) Hinge Assy
Hinge Cover (C)
DCR-SR77E/SR87/SR87E_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/3) POWER BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/3) POWER BLOCK DIAGRAM (2/2)
OVERALL BLOCK DIAGRAM (3/3)
DCR-SR77E/SR87/SR87E_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
A : VIDEO/AUDIO SIGNAL
A : VIDEO SIGNAL
LENS BLOCK
IRIS CD-672/CD-687 BOARD FP-1061 VC-554 BOARD (1/2)
(SHUTTER) FLEXIBLE
CN7001 CN1201 CN1015
BOARD
F10, G9, E10, F9,
C10, C7, B10, B9
AN29, AN28
CCD_OUT+ CCD_OUT+
D8, E9, D9, B8,
A4, B4, A5, B5,
C5, A6, B6, C6,
3, 2
A7, B7, C7, C8
12 27 2 K4 USB_D± USB_D±
IC7002 USB_ID2
Q7002 AD2 - AD13 4
G8, C1, H10, A1, B1
7 - 2, 14, 18, 16, 19
14 - 9, 21, 17, 19, 6
USB_5.0V
15 - 20, 8, 12, 10, 23
CCD
B7, C9, C8, E8, F8,
IMAGER CLAMP Q1007
V1 - V6, RG, (USB)
V1 - V6, RG, H1, H2, SUB H1, H2, SUB IC1201 TG_VD
C4 B8 1