Text preview for : 600CH2.PDF part of Epson Stylus-600 COLOR INK-JET PRINTER
EPSON Stylus Color 600
SERVICE MANUAL
Back to : StCr600.part1.rar | Home
Chapter 2 Operating Principles
2.1 OVERVIEW ...............................................................................................................1
2.1.1 Printer Mechanism .................................................................................................................... 1 2.1.1.1 Printing Mechanism ...................................................................................................... 2 2.1.1.1.1 Printing Process ................................................................................................ 3 2.1.1.1.2 Printing Method ................................................................................................. 4 2.1.1.2 Carriage Mechanism .................................................................................................... 7 2.1.1.2.1 Paper Gap Adjust Mechanism ........................................................................ 10 2.1.1.3 Paper Feed Mechanism and Pump Mechanism .........................................................11 2.1.1.4 Ink System.................................................................................................................. 14 2.1.1.4.1 Pump Mechanism ........................................................................................... 15 2.1.1.4.2 Cap Mechanism .............................................................................................. 17
2.2 Electrical Circuit Operating Principles ................................................................18
2.2.1 C206 PSB/PSE Board .............................................................................................................. 19 2.2.2 C200 MAIN Board..................................................................................................................... 21 2.2.2.1 Reset Circuits ............................................................................................................. 23 2.2.2.2 Sensor Circuits ........................................................................................................... 24 2.2.2.3 EEPROM Control Circuits .......................................................................................... 25 2.2.2.4 Timer Circuit ............................................................................................................... 26 2.2.2.5 DRAM Control ............................................................................................................ 26 2.2.2.6 Print Head Control Circuit........................................................................................... 27 2.2.2.7 PF(Pump) Motor Drive Circuit .................................................................................... 30 2.2.2.8 CR Motor Drive Circuit ............................................................................................... 31
Chapter2 Operating Principles
2.1 OVERVIEW
This section describes Printer Mechanism, electric circuit board (C206 PSB, C200 Main, C206PNL board) of Stylus Color 600.
2.1.1 Printer Mechanism
Unlike previous EPSON Ink Jet printers, printer mechanism of Stylus Color 600 does not have exclusive mechanism to change over paper feeding and Pumping operation. In stead, this control is done by the turning direction of paper feed/pump motor and position of carriage at that time. Also, unlike previous print heads, print head of this printer became one unit combined with black and CMY head. Black head has 64 nozzles, 180 dpi(vertical direction) and CMY head has 32 nozzles, 90 dpi (vertical direction). Also, since these print head is driven by frequency 14.4KHz, this printer can print double resolution(1440 dpi/100-dpi) than Stylus Color. Following figure2-1 shows outline of printer mechanism. Since the head drive frequency of Stylus Color was 7.2KHz, it could be only 720-dpi printing when it driven by 100 cps carriage speed. It performs two-pass carriage operation when Stylus Color 600 performs the 1440 dpi printing towards the horizontal line.
Carriage Unit (Prinr Head Unit)
Platen Drive Mechanism
Timing Belt
Paper Pickup Mechanism
Paper Pick Up Trigger Lever
Pumping Position
Pump Drive Mechanism
Paper Feed Motor
Carriage Motor
Figure 2-1. Stylus Color 600 Printer Mechanism Block Diagram
Rev. A
2-1
EPSON Stylus Color 600 As major printer mechanisms in the figure 2-1, there are four major mechanisms as they are listed below.
1) Printing mechanism 2) Carriage unit 3) Paper pick up mechanism 4) Pump drive mechanism
2.1.1.1 Printing Mechanism
Basic principles of the print head which plays major role of printing mechanism is the same as previous models; on demand type MACH head method, but there is some difference in the resolution. (Refer to figure1-1) Also, unlike Stylus Color II, Stylus 820 and Stylus Color 200 automatic correction type, in order to fix the dispersion of mufti layer piezo electric element which is used for driving each nozzles, it is necessary to input the VH value written on the side of print head by using exclusive program when you replace print head, control board, or the printer mechanism.(However, there are no resistor array for decide the VH voltage on the main control board.) Following explains print head.
PZT
PZT is an abbreviation of Piezo Electric Element. Print signal from C200 board is sent through the driver board on the print head unit and to the PZT. Then, the PZT pushes the top cavity which has ink stored, and make the ink discharge from each nozzle located on the nozzle plate. Cavity Set Ink which is absorbed from ink cartridge go through the filter and will be stored temporarily in this tank, which is called "cavity" until PZT is driven. Nozzle Plate The board with nozzle holes on the printer head surface is called Nozzle Plate. Filter When the ink cartridge is installed, if any dirt or dust around the cartridge needles are absorbed into the head inside, there is a great possibility of causing nozzle clog and disturbance of ink flow and finally causing alignment failure and dot-missing. In order to prevent this, filter is set at cartridge needle below and ink is once filtered here.
Printhead driver board
Ink Cartridge Sensor Actuator Cartridge needle
(Ink Cartridge)
PZT Cavity set Nozzle Plate
Filter Ink Supply Tube
Figure 2-2. Print Head Sectional Drawing
2-2
Rev. A
Chapter2 Operating Principles
2.1.1.1.1 Printing Process
Following figures indicate the sectional drawing of normal state and ejecting state of print head. (1) Normal State: When the print signal is not output, PTZ also does not move in the waiting state(normal state).
Ink Course
PZT
Cavity
Nozzle
Nozzle Plate
Figure 2-3. Print Head Normal State
(2) Ejecting State: When the print signal is output from the C200 main board, IC(IR2C72C and IR2C73C:Nozzle Selector) located on the print head unit latches the data once by 1-byte unit. Appropriate PZT latched by nozzle selector is pushed in to the cavity by applying common voltage from the C200 main board. By this operation, ink that is stored in the cavity pops out from nozzles.
Figure 2-4. Print Head Ejecting State
Rev. A
2-3
EPSON Stylus Color 600
2.1.1.1.2 Printing Method
This section explains printing method of actual printing such as printing text at various resolution select/printing mode and graphics printing. In order to prevent white or color banding which are peculiar problem of ink-jet, new Micro-Weave functions are added to the previous Micro-Weave function. The number of nozzles and printing mode according to the selected resolution are used separately by a user. The table below shows relation between selected resolution and printing mode. 1) 2) 3) Full Overlap Micro-Weave Part Line Overlap Micro-Weave Micro-Weave: (same as previous control) Table 2-1. Resolution and Printing mode Paper feed Forward Non pitch OverlapOverlap[inch] Nozzle Nozzle 15/360 31/360 15/720 29/720 #16·`#30 --#16·`#30 #30·`#32 --#1·`#31 --#4·`#29
Vertical direction [dpi] 360 720
Printing mode
Backward OverlapNozzle #1·`#15 --#1·`#15 #1·`#3
Not used Nozzle
FOL M/W M/W FOL M/W POL M/W
#31·`#32 #32 #31·`#32 ---
Note1: Note2: Note3: Note4:
M/W means Micro-Weave. FOL means Full Overlap Micro-Weave. POL means Part line Overlap Micro- Weave. Forward Overlap-Nozzle and backward Overlap -Nozzle are described in the [1.Full Overlap Mirco-Weave] and [2.Part line Overlap Micro-Weave] below.
Following explains operation outlines of new Micro-Weave functions listed above. [1. Full Overlap Micro-Weave] In order to print one line at horizontal direction, this printing method is designed to complete a printing pattern by two-pass carriage operation with two different types of dot. When this two different types of dot pass one same line twice, it does not print the same dot twice.
The nozzles whose configuration completely match to the black and CMY nozzle are used. (Usually Micro-Weave type) Therefore, all nozzles in case of CMY nozzle and #1·`#63 nozzles in the B2 line in case of black head are its objects. (B1 line is not used at Micro-Weave. Refer to figure1-1 for detail of nozzle configuration.) Out of these 4 color nozzle objects, the number of all nozzles which are going to be used are divided equally into 2 groups. Paper feeding will be done as many as each number of nozzles which are divided into two groups and the same number of dots.(for example, if there are two 10-nozzle groups during 360-dpi printing at longitudinal direction, paper feeding of 10/360-inch becomes available.) At this time, two groups perform Micro-Weave individually and particular lines are passed by two different nozzles.
Note1) These nozzles which are divided into two groups must be set and divided in order to be a pair of odd and even number.
2-4
Rev. A
Note2)
Chapter2 Operating Principles Two groups which are divided according to each elements will be divided either even dot or odd dot when particular lines(level direction line) are formed and eventually, these lines will be completed at selected resolution. Following is a conceptual figure when full overlap microweave orms a particular line.
Nozzle No.#9 Nozzle No.#4
Condition: 360-dpi printing Nozzle: Total 10 nozzle/each color
Particular line(Completed line)
360-dpi
Figure 2-5. Full Overlap Micro-Weave Note 3) The way firmware decides which nozzle becomes even dot or odd dot is determined as it is described below.
If the line which is about to be printed is even line: First dot prints odd dot lines and 2nd dot prints even dot lines.
If the line which is about to be printed is odd line: 1st dot prints even dot lines and 2nd dot prints odd dot lines. Eventually, horizontal resolution will be the same resolution as selected one.
[2.Part Line Overlap Micro-Weave] This printing method is to perform Micro-Weave printing, overlapping a part of nozzles which are used for printing. As a result, a part of raster which is overlapped consists of different browse with different nozzles. The figure below shows 1-line Overlap at 5-dot sending as an example with explanation on the next page.
Pass1
#1 #2 #3 #4 #5 #6
2 3 4
Note1: The paper feed pitch is 5/360-dpi in this figure. Note2: Mark of and mean overlap nozzle.
5 6 7
Raster 1
Raster 10
8 9 10 11
Figure 2-6. Part line Overlap Micro-Weave
Rev. A
2-5
EPSON Stylus Color 600
The difference between Full-Overlap Micro-Weave and Part line Overlap Micro-Weave are following;
Full-Overlap Micro-Weave: Printing is performed, judging if nozzles are even or odd dot by 2 different dots with all different rasters. Part line Overlap Micro-Weave: After particular nozzles(only#1, and #6 in the figure2-7) are determined as overlap nozzles, even or odd dot will be determined like Full-overlap Micro-Weave does. (Forward Overlap Nozzle is determined as even and backward nozzle is odd.) Also, nozzles other than particular nozzles can print at even and odd dot just by one nozzle.
: Head drive frequency is driven half of the ordinal one like 2) below. : Head drive frequency is twice as much as overlap nozzle.
1) Overlap Nozzle 2) Nozzle other than Overlap nozzle
Usually, the firmware changes over automatically these full overlap Micro-Weave, Part line Overlap Micro-Weave, and ordinal Micro-weave according to the selection of resolution. Also, when these three printing modes are performed by the Stylus Color 600, the printer performs top and bottom margin process in order to control the overprinting volume as little as possible.
2-6
Rev. A
Chapter2 Operating Principles
2.1.1.2 Carriage Mechanism
Carriage mechanism is to drive the carriage with print head mounted from left to right or vice versa. The carriage drive motor in this printer is a 4-phase, 200-pole, stepping motor and is driven by 1-2phase, 2-2phase and W1-2phase drive method. This stepping motor allows the carriage to move freely to the particular positions which is necessary for various operation, such as paper feeding, ink absorbing, flashing, ink exchange and cleaning operations. The tables below shows carriage motor specifications and motor controls at each mode. Table 2-2. Carriage Motor Specification Item Description Motor type 4-phase/200-pole Stepping motor Drive voltage Range 42VDC ±5% Internal coil resistance 7.8 ohms ±10% (per phase under 25°C environment) Driving speed(frequency) range[cps (pps)] 5(60) - 340(4080) Control method Bi-pola Drive Table 2-3. Motor Control at Each Mode Driving speed Drive frequency Drive method [CSP] [PPS] 340 4080 W1-2, 2-2,1-2phase drive* 200 2400 W1-2phase drive 100 1200 W1-2phase drive 80 960 W1-2phase drive 40 480 W1-2phase drive 20 240 W1-2phase drive 5 60 W1-2phase drive
Mode High speed skip Printing(Normal) Printing(SLQ) Capping Wiping Cap(valve release) Withdrawal of cap
*Note 1): The reason why plural drive methods exist is that following some sequences described below exist in the each mode and stable carriage operation and printing are performed individually by different drive methods. This drive method is especially necessary for high speed skip.
· Acceleration 1 mode ·¨ · Acceleration 2 mode ·¨ · Deceleration 1 mode ·¨ · Deceleration 2 mode
A /A
Rotor
B /B
C200 MAIN Board Connecter CN6(CN7)
Figure 2-7.CR(PF/Pump) Motor Internal Block Diagram
Rev. A
2-7
EPSON Stylus Color 600 The table below shows W1-2 phase drive sequence at each steps when the rotor of carriage motor makes one rotation. In the Stylus Color 600, in addition to a function that printing is performed with W1-2 drive phase, high speed skip mode which is a function to skip over the blank from the end of the printing data to the next data starting point with high seed can be also performed by 2-2 and 1-2 phase drive. W1-2 phase requires 4 times as much steps as 2-2 phase drive, calculating 2-2 phase as standard. By using this method, it becomes possible to supply constant stable torque to the motor. As a result, it also became difficult to be influenced by vibration from the printer mechanism during printing.
Table 2-4. Motor Drive Sequence(W1-2 phase drive) Phase A Phase B Phase a 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 0 X 1 1 1 1 1 1 1 X 0 0 0 0 0 10a 1 0 1 0 1 0 0 0 1 0 1 0 1 0 0 0 l1a 0 1 1 1 0 0 0 0 0 1 1 1 0 0 0 0 Current Duty +2/3 +1/3 0 -1/3 -2/3 -1 -1 -1 -2/3 -1/3 0 +1/3 +2/3 +1 +1 +1 Phase b 0 0 0 0 0 X 1 1 1 1 1 1 1 1 X 0 10b 1 0 0 0 1 0 1 0 1 0 0 0 1 0 1 0 l1b 0 0 0 0 0 1 1 1 0 0 0 0 0 1 1 1 Current Duty +2/3 +1 +1 +1 +2/3 +1/3 0 -1/3 -2/3 -1 -1 -1 -2/3 -1/3 0 +2/3
Sequence Number
This W1-2 phase drive (or 2W1-2 phase drive) is called Micro-step and is attached with so called 2/3·EVref or 1/3·EVref factor, compared with drive current value (Vref100%) which is supplied at 22phase drive. This Micro-Step allows the rotor to have delicate rotation. In the 2-2 phase drive method, it is usually required to take 4-step sequence in order to rotate the rotor once. However, in case of W1-2 phase, it is required to take 16-step sequence(in the table 2-4, sequence 0·`15) which is 4 times more than 2-2 phase method to do that. Also, in case of 2W1-2 phase drive which can be seen in the Stylus Color etc., it takes 2-step to rotate the rotor once. The table below shows relation of rotation direction of rotor and carriage proceeding direction. Table 2-5. Relationship Between Rotor Direction and Carriage Operation Carriage proceeding Rotation direction of Drive method Proceeding order of direction Rotor sequence HP80 column direction Looking from rotor output 2-2, 1-2, W1-2 phase Sequence No.015 side, clockwise direction 80 columnHP direction Looking from rotor output 2-2, 1-2, W1-2 phase Sequence No.150 side, counterclockwise direction
2-8
Rev. A
Chapter2 Operating Principles The figure below shows carriage mechanism. The print head as a core of the printing mechanism is stored in the carriage unit. This print head keeps the tilt of print head in flexible and adjustable structure by moving the adjustment lever up and down by the tilt adjustment mechanism. (Refer to chapter 4 for more details) Also, parallelism adjustment lever is mounted on the left and right side of carriage guide shaft and it adjusts parallelism degree between platen and shaft when this shaft is installed to the printer mechanism. After this adjustment is completed and operate PG adjustment lever, it becomes possible to change the space between platen surface and print head surface into 2 phases; either 1.1mm to 1.8mm. It is possible to vary the space between platen surface and print head by rotating the axis of carriage guide shaft which itself is decentralized, with the operation of PG lever. This is the mechanism that user can adjust the appropriate PG value by himself according to the paper thickness or any other environmental conditions such as paper curl.
Carriage lock mechanism is to prevent the carriage from being left at uncap position for a long time because of vibration during the printer transport or mishandling by the users. If the carriage is left at uncap position and uncap state of the print head for long time, an ink on the print head surface gradually becomes viscosity. As a result, the nozzle will be unable to discharge an ink. To make matters worse, the holes(crater) of nozzle may be completely clogged by the viscosity ink and it may not be able to return to the normal condition just by cleaning operation. In order to prevent this, printer goes to carriage lock state at the following conditions.
After Power OFF operation: If the power is turned off on the way of printing or any other performance, carriage lock will be performed in the end after completing initialize operation. After power ON operation: After power is turned on and automatic P-On Cleaning is performed, then carriage lock will be performed. P-On Cleaning is an automatic head cleaning that is performed when the power is turned on. The timer IC always calculates printer's power OFF time by the power of lithium battery mounted on the C200 main board. P-on cleaning function automatically selects the cleaning level according to the time which the printer is not in used. After Eject the paper: After Load/Eject button is pressed and the paper is ejected, if the data is not input, the printer performs carriage lock and goes to standby state. However, if the paper is loaded to the printer inside by Load/Eject button, the printer does not perform the carriage lock operation.
Paper Feed Motor
Carriage home position Sensor PF Roller Timing Belt Carriage Unit
Carriage Motor
Eject Roller
Paper guide(Front)
Front Side
Rear Side
Parallelism Adjust Lever
Fixing Bush
Carriage Guide Shaft
Figure 2-8. Carriage Mechanism(Top Viewing)
Rev. A
2-9
EPSON Stylus Color 600
2.1.1.2.1 Paper Gap Adjust Mechanism
This mechanism can be set by the users and can prevent various problems related to low image density or print with any dirt by changing the positions of PG lever according to the paper types. Table 2-6. Paper Gap Adjust Lever Setting Lever position PG adjustment value Front 0 mm (1.1mm between head and platen) Rear 0.9mm (2.0mm between head and platen)
Paper Normal paper, Coated paper Envelops
It is a major premise that parallel adjustment is done correctly for the space between head and platen (PG adjustment value above) which can be changed by platen gap adjustment. Parallel adjustment should be done when the serviceman mounts the carriage guide shaft on the printer mechanism during the production process or repair service. In the adjustment, the space between parallel adjustment lever and gauge should be 1.04 mm.
2-10
Rev. A
Chapter2 Operating Principles
2.1.1.3 Paper Feed Mechanism and Pump Mechanism
Mechanisms that send the paper in the hopper to inside the printer and perform constant paper feed in order to perform printing on the sent paper are called paper feed mechanism as generic name. In the Stylus Color 600, 4-phase, 200-pole hybrid type pulse motor is used in the PF motor as a motive power of the paper mechanism and driving is done at 2-2 and 1-2 phase drive method. This motor is not only used as a power source for paper feed mechanism but also used as power source of pump mechanism which is necessary for print head cleaning. By using this pulse motor, it becomes possible to use high speed driver or intermittent drive for the various paper feeds and pump operations such as paper feed, slight paper feed, high and low speed absorption of pump operations. Following tables(Table 2-7 and 2-8) show PF motor specifications and control method at each mode. Table 2-7. PF Motor Specification Item Description Motor type 4-phase/200-pole Stepping motor Drive voltage 42VDC ±5% Coil Resistance 7.8 ohms ±10% (per 1 phase under 25°C environment) Drive frequency [cps (pps)] 400 - 4320Hz Control method Bi-pola Drive Table 2-8. Motor Control Method at Each Mode Drive Method Drive Frequency [Hz] Paper feed A 2-2 phase 4320 Slight paper feed 1-2 phase 400 Slight paper feed 1-2 phase 2400 High speed attraction of pump 2-2 phase 4100 Low speed attraction of pump 1-2 phase 1800 Low speed paper feed 1-2 phase 1200 Paper feed B 2-2 phase 3400 Paper feed C 1-2 phase 4000 Ordinal absorption of pump 1-2 phase 4100 Mode
Pulse Space (Ês) 231 2500 417 243 555 833 294 250 243
Following tables show 1-2phase drive method at PF motor drive and each drive sequence at 2-2phase drive method. Table 2-9. 1-2 Phase Drive Method Clockwise Counter clockwise Phase A +2/3 0 -2/3 -1 -2/3 0 +2/3 +1 Phase B +2/3 +1 +2/3 0 -2/3 -1 -2/3 0 Phase A +2/3 +1 +2/3 0 -2/3 -1 -2/3 0 Phase B +2/3 0 -2/3 -1 -2/3 0 +2/3 +1
Step No.
1 2 3 4
Step No.
Table 2-10. Drive Sequence at 2-2 Phase Drive Clockwise(CW) Counter clockwise(CCW) A +2/3 -2/3 -2/3 +2/3 B +2/3 +2/3 -2/3 -2/3 A +2/3 +2/3 -2/3 -2/3 B +2/3 -2/3 -2/3 +2/3
1 2 3 4
Rev. A
2-11
EPSON Stylus Color 600 Papers on the ASF (auto-sheet-feeder) supplied by the user are carried to the printer inside by paper pick up sequence. Unlike the previous models, ASF of Stylus Color 600 has mufti feed prevention mechanism. Following explains this function and figure below shows its mechanism.
[1. Multi feed prevention mechanism] When the Load/Eject button is pressed, reversed rotation of PF motor is performed. The return lever resets papers which are already in the out of stand by position in the stand by position and make it possible to perform stable paper feeding by picking up the paper again.
Pintch Roller D-Cut Roller CAM Hopper Hopper spring
2) 1) 2) Return Lever [Standby state] Pad spring [Returning state]
Figure 2-9. Multi Paper Feed Prevention Mechanism
Following explains process of multi feed prevention step by step. Refer to the figure above and confirm its operation. [Step 1] [Step 2] [Step 3] When the load/Eject switch is pressed or printing order is input from the PC, PF motor rotates counterclockwise and makes the CAM rotate towards direction of 1 in the figure above. When the CAM covers the notch by the return lever, that position is considered as home position, being monitored by ASF sensor. When the CAM rotates toward 1 in the figure above, the return lever is pushed by the notch of CAM and falls towards 2. At this time, the return lever moves to direction 3 by this motion, and push down the pad which is waiting in the below part. At this time, friction of pinch roller and pad will be canceled. The papers which are out of stand by position by the previous paper feed motion are returned to the paper stand by position by flip over strength of return lever. After this, PF motor rotates clockwise and the printer goes to pick up sequence.
[Step 4]
2-12
Rev. A
Chapter2 Operating Principles In the paper pick up mechanism of Stylus Color 600, same mechanism as Stlylus Color IIs/820 are applied. This mechanism changes adjoined lines of gear by colliding trigger lever with carriage unit and convey the motive power on the platen to the ASF side(paper roller). The figure below shows mechanism with explanation.
[2. Paper pick up mechanism] When the Load/Eject switch is pressed or printing order is input, the carriage unit moves until the left edge and collides with paper pick up trigger lever. When the carriage collides with this trigger level, a planetary gear located on the same axis is also pushed at the same time and conveys the motive power on the platen to the adjoined gear line side for ASF drive.
Paper Pick Up Trigger Lever Eject Roller Drive Gear Planetary Gear Eject Roller Transmission Gear
ASF Roller Drive Gear
PF Motor Pinion Gear ASF Roller Transmission Gear Platen Roller Drive Gear Platen Roller Transmission Gear
Figure 2-10. Paper Pick Up Mechanism [3. Paper feed mechanism] After papers in the ASF receive controls from pick up and multi feed prevention mechanism, they are sent to the printer inside. The papers picked up by paper roller in the ASF goes to between platen and roller support. Also, the eject roller pushes out the paper completely until the end and the roller support drops the paper in the eject tray. The eject roller is driven with an eject paper notched roller as pair where is located on the paper eject roller. Paper eject notched roller solves the deflection of paper that is in the between platen eject notched roller and paper eject roller and always keep a certain space between print head and paper surface. The figure below shows paper feed mechanism.
Paper Eject Notched Roller
Support Roller
Eject Roller
PF Roller
Figure 2-11.Paper Feed Mechanism
Rev. A
2-13
EPSON Stylus Color 600
2.1.1.4 Ink System
Ink system mechanism consists of 1)cap mechanism, 2)pump mechanism, 3)carriage lock mechanism, 4)waste ink absorber and 5)ink sequence. Out of these mechanism, from 1) to 4) are physical mechanism and parts which are mounted on the printer mechanism and 5) ink sequence is performed automatically by firmware. Also, unlike previous models, since Stylus Color 600 has no engage/disengage mechanism to change over pump mechanism and paper feed mechanism, it is one of the major characteristics that pump and platen are always at work whenever the PF motor is driven. The figure below shows head positions when the ink system and various ink sequence are performed.
Platen Drive Gear Eject Roller Drive Gear Eject Roller Trasmission Gear
Head Cleaner Carriage Lock
PF(Pump) Motor Pinion
Pump Roller Cap Unit
Figure 2-12. Ink System Mechanism
Printable Area
2975 dot H G F E D C B
CRHP
A
A: Dummy pumping position B: Home position C: Flashing position(right side) D: I/C replacing position E: Wipping complete/Rubing start position F: ASF Standby position G: Flashing position H: ASF pick up position
Figure 2-13. Major Ink Sequence Position on the Carriage Mechanism
2-14
Rev. A
Chapter2 Operating Principles
2.1.1.4.1 Pump Mechanism
In the Stylus Color 600, there is no switch or mechanism to change over the pump/paper feed mechanism. Therefore, whenever the paper feed/pump motor rotate, pump drive roller in the pump unit inside rotates. However, ink absorption/non ink absorption are separated by the roller rotational direction. Also, even if the pump driver rotates toward ink absorption and the carriage position is in the false absorption position, only driving in the pump mechanism is performed and actual ink attraction is not done. The figure below shows process of conveying motive power to the pump drive roller.
Gear A
Axis of Paper Eject Roller
Gear B
Gear C
Actually, these parts are one unit.
Compression Spring Pump Drive Roller
Figure 2-14. Pump Mechanism Power Transmission Process
The process of conveying the motive power to the paper eject roller by rotating the pinion of PF motor is descried in figure 2-14. This motive power is conveyed to the Gear C through Gear B. In the figure above, although the lever in order to drive Gear C, carriage lock, head cleaner mechanism is shown separately, it is constructed as one unit. Since the engagement of these two parts depends on the tension of the compression spring, if the lever is burdened, only Gear C and pump roller rotate and no more motive power is conveyed to the lever part.
Rev. A
2-15
EPSON Stylus Color 600 The table below shows PF/Pump motor rotational direction and pump system operation.
Table 2-11. Relationship Between Pump Motor Rotation and Pump Operation PF/Pump motor rotational direction Pump unit operation Clockwise(CW) 1)Release from the Pump pressure welding forward rotation 2)Head cleaner reset 3)Carriage lock reset Counterclockwise(CCW) 1)Rotation towards pump pressure welding backward rotation 2)Head cleaner set 3)Carriage lock set The figure below shows the pump operation at clockwise and counterclockwise rotation.
CW Rotation
CCW Rotation
Tube pressured
Tube released
Figure 2-15. Pump Roller Rotation and it's Operation
In the ink absorptive operation such as cleaning, flushing initial ink charge except for printing operation, ink in the ink cartridge drains to the waste ink absorber(pad) through the cap by the pump unit drive. In case of printing and flashing drive, ink is popped out by the PZT in the print head, but in case of absorptive operation such as cleaning and initial ink charge, ink absorption is performed only by the pump drive without PZT drive after the head surface is adhered to the cap. The next page explains cap mechanism and relation between printer operation and cap.
2-16
Rev. A
Chapter2 Operating Principles
2.1.1.4.2 Cap Mechanism
In the cap mechanism, in order to prevent ink from being thickened on the head surface, it is controlled that the head surface stays adherent to the rubber frame of the cap surface when the power is off. The absorber is spread in the cap and can hold a certain amount of ink which is absorbed from the head without draining it to the waste ink pad. Also, in the bottom of absorber, there are two valves in order to control adhesion of head and cap surface, and one exit to drain ink to the waste ink pad.
A
Flag for Carriage
B
Ink Eject Valve Negative pressure release valve
Valve
Close state
Release state
Flag for frame
Head surface and cap are adhered each other. Actual and false absorptions. During cleaning, initial ink charge, and right flushing.etc.
Ink absorption in the cap. During left flushing and paper feeding,etc.
Figure 2-16.Cap Mechanism Operation Principle If the carriage is out of HP(in this case, in the printable area or paper feed position), the valves on the cap mechanism stays in the position A in the figure above and are always closed. In this condition, the carriage collides with flag, actual ink absorption and slight ink absorption are performed. Also, by moving the carriage to further right side and colliding the flag for opening the valves with the frame, negative pressure is released in the state that head surface and cap are adhered. This makes it possible for ink on the nozzle plate surface to be ready for leaving from the cap in the stable condition.
Rev. A
2-17
EPSON Stylus Color 600
2.2 Electrical Circuit Operating Principles
Stylus Color 600 contains the following four electric circuit boards.
C206 PSB/PSE board C200 Main board Head Driver board C206 PNL board
C206 PSB/PSE, C200 board are explained in this section. The head drive board is installed in the head uniton the carriage. The figure below shows major connection of the 3 boards and their roles.
RCC Switching Regulator (C206 PSB/PSE Board) +5 V DC Main Control Board (C200 Main Board) +5 V DC
INK END Sensor (Firm Wear)
AC100V
+42 V DC
+42 V DC
CR Motor PE Sensor
PF MOTOR (Pump Motor) BCO/CCO Sensor ASF Lever Position Sensor
Thermistor
Print Head
Head Drive Board
Figure 2-17. Electric Circuit of Stylus Color 600
2-18
Rev. A
Chapter2 Operating Principles
2.2.1 C206 PSB/PSE Board
C206 PSB/PSE board is a power supply board with a RCC switching regulator, which generates +42VDC for drive part and +5VDC for logic part to drive the printer. One of the major characteristic of this board is that the same secondary switch is used as Stylus Color series printer. By using this switch, the following difference can be seen as superficial phenomena compared with products applied with primary switch method, such as Stylus Color IIs, II and Stylus 800/1000 series printer. The table 2-12 below shows application of voltages generated by C206 PSB/PSE board. 1) Even if the switch is turned off during the middle of printer operation, since the driving power is turned off after the carriage goes back to the carriage lock position, the possibility of clogging ink nozzle will be decreased. 2) If the switch is turned off when the papers in the printer are still being carried except for the papers in the hopper, the same operation mentioned above is performed and the driving power is turned off after the paper is completely ejected. Table 2-12. Application of DC Voltage Application CR Motor PF/Pump Motor Head driving power supply Power supply for logic control System control signal Sensor circuit power supply voltage LED panel drive power supply Nozzle selector control signal power supply voltage
Voltages +42VDC
+5VDC
Figure 2-18 shows block diagram of C206 PSB/PSE board. The process from the input of AC100V to the output of DC42V and 5V is explained below. 1) Regardless of the state of power switch(On or OFF), the voltage is always applied in the primary side of the power supply board from the moment or at the state that AC-plug is plugged in. At this time, F1 plays a role of preventing AC100V from coming into the F1. L1 and R1-R2 also prevent high harmonic wave noise generated in the RC circuit filter which consist of C1·`C4 and R1·`R2 from going out, and eliminate the noise from outside here. 2) The AC is full-wave rectified by diode bridge DB1, and converted to electrolytic capacitor C11.
2 x AC in voltage by smoothing
3) The pressured up direct current makes Q1 On through the starting resistor R31 and starts the primary side of the circuit. 4) When the primary side is On state, the energy(current) led by the electromagnetic induction through the trans (T1) does not flow to the secondary side since the diode(D51) on the secondary side is installed in the opposite direction. 5) When the energy which is charged in the trans is reaching the saturated state, the voltage which makes the Q1 On becomes weak gradually. At the point that this voltage drops at the certain voltage, C13 absorbs the current in the opposite direction and Q1 is quickly shut off by the resulting sharp drop. 6) When the primary side is turned off, the energy charged in the T1 is opened according to the diode(D51) direction which is installed on the secondary side. Basically, 42 V DC is output by these circuit operations and the number of T1 spiral coil . 7) +5VDC is generated by pressured down this +42 V DC as power supply. IC51 pressures down the +42 V DC and generates precise +5V DC by chopping off the output, forming the standard santooth waveform by the outer RC integration circuit.
Rev. A
2-19
EPSON Stylus Color 600
DB1 C11 T1 D51 +42VDC C51 Smoothing circuit ZD81-86, ZD51
Full Wave Rectifier circuit
L1,R1-R2 C1-C4
Smoothing circuit
Q1 T R A N S
+5V generation circuit (IC51)
+5VDC
Filter Circuit
F1
Main switching circuit
Q2,Q3, Q31,PC1
+42V constant voltage control circuit
C84,Q84
ZD52,87
ZD53
Power OFF Delay circuit
Prevention of current flow
Feedback circuit
+42V overvoltage protection circuit
+5V overvoltage protection circuit
PSO Signal
PC1
Photo coupler
AC100V
Figure 2-18. C206 PSB/PSE Board Block Diagram
The C206 PSB/PSE board has various control circuits to stop output if malfunction on the power supply board, on the main board or on the duty of printer mechanism happen. Following explains each control and protection circuits. 1) +42V Line Constant Voltage Control Circuit: The output level of the +42V line is monitored by a detection circuit consisting of seven Zener diodes. This circuit prevents voltage from dropping for constant output voltage. 2)+5V Line Over voltage Protection Circuit: This protection circuit is in the same line as +42V overvoltage protection circuit is located. The output voltage level of the +5V line is monitored by a Zener diode. This circuit shuts down the circuit operation forcefully when the voltage level exceeds +9V. 3) +42VDC Line Over voltage Circuit This ciruit is in the same line as +5V line over voltage protection circuit is located. The output level is monitored by two Zener diodes. If the voltage level exceeds +48VDC, this circuit stops circuit operation forcefully. 4) +5V Line Constant Voltage/Constant Current Control Circuit: The output current is monitored by a +5VDC generation switching control IC(IC51), which also monitors the output voltage. This information is input to the internal comparator and stabilizes+5V line. Also, operation of the secondary side switch is explained below. 1) When the power is turned on, Q1 repeats ON/OFF automatically along with the increase and decrease of energy on the trans coil at the primary side. While the power is being on, PSC signal is input to the power supply board from the C200 main board. This signal turns Q84 on and it becomes possible to discharge energy between 8-9 of T1. At this time, even if the power is turned off, the electrolytic capacitor keeps Q84 on for a while. By this electrolytic capacitor, output is hold at least 30 seconds even after the power is turned off. This time helps the printer to complete the P-Off operation.
2)
2-20
Rev. A
Chapter2 Operating Principles
2.2.2 C200 MAIN Board
Various DC voltage generated on the C206 PSB/PSE board is added various signals in order to drive the printer function on the C200 MAIN board, and the drive of CR/PF(Pump) motor and printing head is performed. This control board consists of system part and drive part. In the system part, there are formation and controls of various signals in order to drive the CR/PF(pump) motor, sequence control by input from the sensor circuit, and also output of signal to select appropriate nozzle for the printing head. On the other hand, the drive part has constant current drive by the driver IC for the CR/PF(pump) motor drive and trapezoidal waveform circuit for head drive.
C200 MAIN Board
PROM4M (IC3:EPROM) M5M411664 (IC4:D-RAM) 4-32M (IC6:CG)
System
DRAM Control Head Temperature
TPM 95C061 (IC1:CPU)
E05B43 (IC2: Gate Array)
CR/PF Motor Drive Panel I/F
to B
Head Common Drive Centornics I/F SN75LBC775 (IC16 Transceiver) Serial I/F
to A
Sensor Circuit EEPROM (IC11) Timer (IC10)
From A
H8D2813D (IC7) LB1845 (IC14) LB1845 (IC15)
Print Head
Power
From B
Carriage Motor
From B
PF(Pump) Motor
Figure 2-19. C200 MAIN Control Board Block Diagram
[CPU] The C200 MAIN board is controlled by a 16-bit CPU(TMP95C061AF) running at 25MHz. Gate array manages most of controls and monitors. Likewise Stylus Color, the D-RAM is applied for RAM which is used as work area for receiving data and developing the data and CPU manages its control such as CE, RAS/CAS controls. [Gate Array] E05B43 controls following functions.
Each motor performs data transmission(W1-2 phase) that motives Micro-Step. Head voltage control: In the ink jet printers, drive voltage wave form(trapezoidal wave form) in order to drive PZT is formed in the various shapes according to the types of the printers. Therefore, it is necessary to form appropriate drive form for each head. Head voltage control forms necessary waveform for each control signals and outputs them. EEPROM control: The correction value to eliminate the error of each printers at the production process is installed in the fixed address of IC. When the power is turned off, the contents set by users is written instantly, and is red to the RAM when the power is turned on. Sensor Data: The sensor detects information at the various conditions, which is necessary for the printer operation. The gate array recognizes signals and changes over to the next control.
Motor control :
Rev. A
2-21
EPSON Stylus Color 600 Timer Data:
The timer IC that uses lithium battery as power source monitors how long the power is off. When the power is turned on, it is changed to appropriate cleaning level according to the time that the power is off. The gate array receives serial data through the transceiver IC. With the use of IEEE1284 Nibble mode, it became possible not only to receive the data from the host but also to return various information which the printer possesses to the host.
Serial Data: Parallel I/F control:
[Common Driver IC] The trapezoidal wave form circuit for head drive is became to HIC from the previous discreate structure. Because of this, it is not necessary to adjust the adjustable VR on the board during production process. Various electric charge/discharge control signals are all processed in the HIC. [CR/PF Motor Drive Circuit] Constant current drive is performed by the HIC. Out of this, only CR Motor is controlled for Micro-Step control and HIC becomes possible to flow the appropriate current value at each steps. (PF Motor has only 1-2, 2-2phase drive method). Also, bipolar drive is performed on the 4 cables individually. Following pages explain each major control circuit.
2-22
Rev. A
Chapter2 Operating Principles
2.2.2.1 Reset Circuits
The reset circuit prevents the CPU from running away, which is caused by the unstable voltage in the logic line during the power ON/OFF. Also, this circuit monitors level of power voltage at the overloading or malfunction on the circuit and manages the printer to operate normally, keeping the damage to the printer minimum during the abnormal situations. On the C200 main board, 2 ICs are mounted ; IC for monitoring the voltage level (logic line) and IC for monitoring the voltage level (power line) and both are monitored by the gate array and CPU. The figure below shows reset circuit block diagram with explanation on the next page.
+5V +5V PST592D (IC8) Vout NRES Vcc GND
1 2 3 4 C47 R138
R1
TMP95C061 (IC1) P 8 5
P84 /NMI /RESET 1 6 3 0 176
E05B43 (IC2)
15 10
/RESET
+ 5 V
+42V M51955B (IC9) 2 4
NC8 8
R10
IN GND
7 VCC 6 OUT 5 NC5
R6
Figure 2-20. Reset Circuit Block Diagram
[PST592(IC8)] The actual operation of the circuit is to keep outputting Low signal until +5V line goes up to +4.2V when the power is on, and to cancel the reset signal with output of High signal when the voltage goes up more than 4.2V. [M51955(IC9)] This IC also performs as monitor on the power line same as the reset IC for logic described above. High/Low is judged at the 33.2V. [Relation between IC8 and IC9] Reset signal which is low and output by IC9 is input to the CPU and gate array and system reset operation is performed. Also, this signal is detected on the IC9(IC for reset monitor, power line) and outputs the same Low signal towards CPU/NMI terminal by being input to NC5.
Rev. A
2-23
EPSON Stylus Color 600
2.2.2.2 Sensor Circuits
The following sensor circuits are mounted in the Stylus Color 600 and selects appropriate operations based on the returned information.
ASF Sensor: (Photo)
An ASF sensor detects the position of return lever when the power is turned on, and causes the paper to be picked up by the pick up roller from the normal initial condition. (Refer to section 2.1.1.3 for detail.) A PE sensor determines if there is paper in the printer. Based on the signal form this sensor, a particular paper edge treatment such as Micro-weave printing is performed. A HP sensor detects the carriage home position. It is used for managing printing position and cleaning, etc. A thermistor sensor keeps stable printing quality, changing PZT drive voltage(VH) slightly according to changes of environmental temperature. Cartridge sensors are built into the Bk, CMY cartridge on the carriage unit respectively to determine if the cartridge is installed or not when it is exchanged or the power is turned on. In case of Stylus Color 600, the counter is reset at every time the cartridge is removed.
PE Sensor: (Photo)
HP Sensor: (Photo) Thermistor Sensor:
Cartridge Sensors:
The figure below shows sensor circuit. Out of the data such as EPW with IEEE 1284 Nibble mode to be returned to the host, the data to indicate ink consumption is calculated and managed by the counter of the firmware. Therefore, it is omitted here.
TMP95C061 (IC1)
Vref 18
+5V
AGND
17
CCO BCO
CN8
AN0
20
3 THM
CN8
+5V
+5V 3 PEV GND 2 1 3 HPV GND 1 HP 2 1 3 ASFV GND ASF 2 1 CN11 CN5 CN4
E05B43 (IC2)
SW8 CCO(199) SW7 BCO(201) SW6 PE(203) SW5 HP(205) SW4 ASF(207)
3 +5V 2
PE
F Figure 2-21. Sensor Circuit Block Diagram
2-24
Rev. A
Chapter2 Operating Principles
2.2.2.3 EEPROM Control Circuits
The EEPROM of Stylus Color 600 has following contents. Gate array E05B43(IC2) controls operations of reading data when the power is on and writing data when the power is off.
Ink consumption(Bk, CMY) CL counter(Various cleaning operations that are previously done are memorized) Destination information Information of various adjustment values(Bi-D, VH voltage, etc.) CPSI pass word Other various setting values by the user
EEPROM is connected to the Gate array by 4 lines and performs following functions. The figure below shows EEPROM control circuit.
CS : CK : DI : DO :
Chip selection signal Data synchronism clock pulse Data writing line(serial data) at power off. Data reading line(serial data) at power on.
+5V
93C46(IC11) 8 6 5 VCC ORG GND CS CK 1 2 130 129 128 127 E05B43(IC2) ECS ECK EDO EDI
DI 3 DO 4
Figure 2-22. EEPROM Circuit Block Diagram
Rev. A
2-25
EPSON Stylus Color 600
2.2.2.4 Timer Circuit
The lithium battery is mounted on the C200 MAIN board and calculates how long the printer is not in used. The timer IC(IC10) starts counting with oscillation motivated by the CR3 using this battery as a power source. The figure below shows connection of the Timer circuit.
+5V D1 D4 8 2 CR3 3 4 VDD XOUT XIN VSS S-3510ANFJ (IC10) /SCK SIO 6 7 CS 1 125 122 123 126 TCE TIO TCLK TDATA E05B43(IC2) BAT1
+5V
Figure 2-23. Timer Circuit Block Diagram
The followings explain about operation of this circuit.
When the printer is on, power is supplied to the Timer IC by applying +5V quickly through the D4. This power is also used for the power to oscillate the outer CR3. The oscillation wave form is input to XIN terminal. Since the oscillation wave form of CR1 is analog waveform, it is processed into the pulse form in the Timer IC. When the printer is turned on, the Timer IC outputs power off time as serial data to the gate array. Once the printer is turned off, 3VDC of BAT1(lithium battery) is supplied as power source for the Timer IC through D1. Since +5V at the power on is higher than +3V of the lithium battery, the power is not being consumed from the lithium battery.
2.2.2.5 DRAM Control
In the Dynamic RAM control, output and formation of CAS and RAS control signals become necessary in addition to the output of CS signal. The CPU TMP95C061AF not only controls that but also perform the output of CS signal of P-ROM. Refresh timing is performed in the CAS Before RAS.
2-26
Rev. A
Chapter2 Operating Principles
2.2.2.6 Print Head Control Circuit
The print head control circuit of Stylus Color 600 has following characteristics. Common waveform circuit became one HIC. Micro-vibration mode is added.(when the CR motor is accelerating) High speed drive 14.4KHz (trapezoidal wave form Enhanced Nozzle configuration (resolution in the vertical direction)90dpi (However, black nozzle is 2 lines structure)
Also, Stylus Color 600 has Micro-dot control as dot shooting control. There are total three dot shooting controls on this printer. · Normal Dot mode(Single Firing) · Normal Dot mode(Dual Firing) · Micro Dot mode · Micro-Vibration(Not printed) The control circuit is considered as two divided parts; 1) trapezoidal wave form generation circuit (common drive circuit) to drive PZT in the head, and 2) Nozzle-selector drive circuit to determine which nozzle should be used. The Nozzle-Selector is attached to the head unit just like the previous models. The common drive circuit is became as HIC and mounted on the C200 main board. [Common drive circuit]
+5V +42V
F1
H8D2813D (IC7) VM VCC E05B43 (IC2) CHG KC1 ND1 ND2 MD1 MD2 DATA DATA /STB CLK CHG KC1 ND1 ND2 MD1 MD2 DATA DATA /STB CLK CTC
DTB
23 22 21
CN8
20 19 18
GND1 GND2
Figure 2-24. Print Head Control Circuit Block Diagram
The shape of trapezoidal wave form will be different according to the printing operation, slight vibrations at the non-printing nozzle and waiting condition. However, IC7(H8D2813) generates all wave forms as drive wave forms by resistance(electric) welding control of common voltage drive control signal that is output from the IC2(E05B43) in the figure above. Table 2-13. Specifications of H8D2813 Operation Contents 42V ±5% Starts supplying after 5V rises and be stabilized./ Stops supplying before +5V drops. 2SC3746(for charging), 2SA1469(for discharging) Final drive element Off on the both charging and discharging sides. Reset Operation Supplies drive power source. This common voltage trapezoidal wave form can be observed anytime after the +5V rises even if there is printing data or not. (Q7:3-pin, or Q9:3-pin and GND on the C200 main board) Item Power Voltage
Rev. A
2-27
EPSON Stylus Color 600 [Nozzle Selector Drive Circuit] In order to motivate the print head to carry out printing, it is necessary to transmit the print data to the appropriate nozzles, which becomes direct signals to drive PZT. This data transmission is performed by the serial transport method, however the data output for each black and CMY head is transmitted by the parallel method. The figure below shows data transmission circuit.
VH COM NCHG
Gate Array E05B43(IC2)
CLK SI1 SI2 SI3 SI SI1 SCLK LAT XCHG COM VHV VD1/2 For Black & Magenta data latch
U102 IR2C73C
SI SCLK LAT XCHG COM VHV VD1/2
LAT THM
For Cyan & Yellow data latch
Figure 2-25. Nozzle Selector Circuit Block Diagram CLK(Clock) pulse considered as source of serial communication is commonly used for both black and CMY. The serial data transmits data as 64-Clock unit, synchronizing with this pulse. After the data transmission of 64-Clock is completed, LAT(Latch) signal is activated and is hold temporarily in the IR2C72C(U101) At this time, since the number of nozzle for Color head is fewer(21-nozzles) and different from the ones for black head, 0 is transmitted forcefully for the data for 43 nozzle (64-21=43).
2-28
Rev. A
Chapter2 Operating Principles
After the data transmission by the nozzle selector(IR2C72C, IR2C73C) is completed and a certain time passes, trapezoidal wave form generated by the common drive circuit once sends electric current to the PZT for the proper nozzles which are determined in the nozzle selector circuit. This motivates PZT and ejects the ink in the cavity. The figure below shows normal dot data transmission timing in order to from 1-dot.
Common Waveform
Com SCLK LAT NCHG CHG ND1 ND2 KC1
Figure 2-26. Common Drive Circuit Block Diagram
64-dot
Rev. A
2-29
EPSON Stylus Color 600
2.2.2.7 PF(Pump) Motor Drive Circuit
IC15(UDN2917) is used for driving PF(Pump) motor. In the IC, Bi-pola drive PWM current control type is performed, making it possible to provide stable current to each phase of motor. Also, it makes possible to change over the reference voltage as drive current settings by making 3 combinations(100%,66% and 33%), using 4 current setting ports(input). (Refer to 2.1.1.3 for motor and details about sequence) However, firmware does not drive Micro-step in the Stylus Color 600. The figure below shows the block diagram of Unlike using Uni-Pola drive, there is no cable for GND in the motor since Bi-Pola drive is performed in the PF motor.(Refer to section 2.1.1.2 since carriage motor interior connection diagram has the same connection as the PF motor's phase connection. This helps to understand the reason why the direction of current is controlled freely in each phase by the combinations of high/low control signals.
E05B43(IC2)
PFA0
UDN2917(IC15)
57 58 55 56 59 50
46-49 Current Selection Resistor 2
1 2 3 4
PFA1 PFB0 PFB1 PFAPH
PFBPH PFV0-PFV3
1
23
I10
PFA PF/A PFB PF/B
I11 I20 I21
PH1 PH2 Vref1
24
43 26 44 25 4 5
Vref2 SENS1 E1 SENS2 E2
Figure 2-27. PF(Pump) Motor Circuit Block Diagram
The current control is performed by output port(46·`49 pin) of E05B43(IC2), its outer resistance circuit and driver IC15(UDN2917). First, firmware possesses 16 ways of current values as current table out of combinations made by 5 resistance which are connected to the output ports(46·`49 pin) in the gate array. On the other hand, signals which are output by combination of these resistance's on/off are input in the 25 and 44 pins. HIC is driven at the same standard voltage for each A and B phase. Actual on/off control to send electricity through the motor is performed by the process that SEN1 and SEN2 terminals (2 and 13 pin) detect the input signal from the gate array which is monitored by the interior comparator, confirm the current that actually flew the phase as current value again and perform the feed back to the on/off. The figure below shows relation between input signal to the driver IC and motor control.
+42V +5V
Note: In case of PF motor, same reference voltage is input to UDN2917 for both phase A and B, but differet reference voltage is set individually for phase A and B, in case of R1 CR motor. E05B43(IC2) Gate Array
Ra
R2
R3 R4
Rb
RS
If feeds back the current that actually flew in the coil to the comparator.
It varies load resistance by the control signal and changes the ratio of partial pressure.
UDN2917(IC14,IC15)
Figure 2-28. PF(Pump) Motor Driver Internal Block Diagram
2-30
Rev. A
Chapter2 Operating Principles
2.2.2.8 CR Motor Drive Circuit
In the CR motor, the same UPD2917(IC14) as the PF motor has used. In the IC, Bi-pola drive PWM current control type is performed, making it possible to provide stable current to each phase of motor. Also, it makes possible to change over the reference voltage as drive current settings by making 3 combinations(100%, 66% and 33%), using 4 current setting ports(input). (Refer to 2.1.1.3 for motor and details about sequence) In the carriage motor, firmware supports the micro-step driving in the Stylus Color 600. The figure below shows carriage motor drive circuit.
E05B43(IC2)
CRA0 75 76 CRA1 CRB0 72 2
UDN2917(IC14)
1
23 I10
A /A 3 B /B
21
1 2 3 4
PFA PF/A PFB PF/B
I11 I20 I21
PH1 PH2 Vref1
CRB1 73
24
43 26 Current Selection Resistor 44 25 4 5
CRAPH 77 CRBPH 74
MTBV0-V4 MTAV0-V4
Vref2 SENS1 E1 SENS2 E2
Figure 2-29. Carriage Motor Circuit Block Diagram
Unlike using Uni-Pola drive, there is no cable for GND in the motor since Bi-Pola drive is performed in the CR motor.(Refer to section 2.1.1.2 since carriage motor interior connection diagram has the same connection as the PF motor's phase connection. This helps to understand the reason why the direction of current is controlled freely in each phase by the combinations of high/low control signals. The current control is performed by output port(60·`67 / 70·`71 pin) of E05B43(IC2), its outer resistance circuit and driver IC14(UDN2917). First, 10 resistance which are connected to the output port of the gate array divide each current values of phase A and B in the CR motor. The firmware possesses 16 different ways of current values individually as current table out of combinations made by 5 resistance which are connected to the output ports(46·`49 pin) in the gate array. On the other hand, signals which are output by combination of these resistance's on/off are input independently in the 25 and 44 pins. HIC is driven at the different standard voltage for each phase A and B. Actual on/off control to send electricity through the motor is performed by the process that SEN1 and SEN2 terminals (2 and 13 pin) detect the input signal from the gate array which is monitored by the interior comparator, confirm the current that actually flew the phase as current value again and perform the feed back to the on/off. (Refer to before page since it is same as the one of PF motor)
Rev. A
2-31