Make | Model | Problem | Solution | Date |
| | | |
Found: 85
|
Beko | 20306NX | Dead - MOSFET 2SK1118 s/c | Only works short time aft replacement - chopper tfmr faulty | 14-09-04 |
Bush | 2063NTX | Field collapse | C701 4n7 leaky | 14-09-04 |
|
Bush | 2063NTX/A | Dead | s/c BUZ90A o/c 330 K ( R805 ) | 14-09-04 |
Bush | 2064NTX | Field collapse | Check sawtooth wform at pin 42 IC100 TDA8361, if absent replace R149 3M3 | 14-09-04 |
Bush | 2068NTX 11AK10-17 | Dead with Q801 P3NA61 Power FET s/c | Replaced with BUZ90 or IRFBC40, TDA4605-2, R809 0R47 1/2w safety res, 330k & R803 820k | 14-09-04 |
Dansai | CTV1406 | Int dead & makes screeching sound | Dry joints T751 line dr tfmr | 14-09-04 |
Dansai | CTV1406 | INT DEAD POWER SUPPLY PINGS | LINE DRIVE TX DRY | 14-09-04 |
Fidelity | C14M06 | Int field collapse | D25 1N4002 pin 6 IC10 TDA3653 int o/c | 14-09-04 |
Fidelity | CTV1406 | Dead | HT = 130v at LOPtr - 0R68 safety res in series with line dr tr o/c & tr s/c | 14-09-04 |
Fidelity | CTV1406 | Drifts off tune | isolation diode slider no.5 tuning preset leaky | 14-09-04 |
Goldstar | CIT2068F | St/by only - if mains sw held in snowy raster shows | Micro IC701 pins 31 & 32 had no 10Mhz signal present - Xtal faulty | 14-09-04 |
Goldstar | CIT2068F | Stuck in StBy - if switch held in set starts but o | No 10Mhz on pins 31 32 of micro as xtal us | 14-09-04 |
Goodmans | 2065TS | Dead or int dead - St/by LED not always coming on | Dry joint RC727 sm | 14-09-04 |
Goodmans | 2065TS | Txt & Menu to left | I702 DAEW1AT24C16PC EEPROM faulty | 14-09-04 |
Goodmans | 2066TS Daewoo | St/by only after EHT comes up | I901 TDA6103Q U/S. | 14-09-04 |
Goodmans | 206N/216NS | 1 Pri col missing | R908, 909 or 907 100k on crt base | 14-09-04 |
Goodmans | 206N/216NS | Black raster - sound ok | CRT faulty - unplug P602 to test, wait until screen lights then refit - shows a dull pic | 14-09-04 |
Goodmans | 206N/216NS | Dead - F801 blown | IC801 STR5707 reg faulty | 14-09-04 |
Goodmans | 206N/216NS | Field collapse | C301 s/c, C405 & I301 blown | 14-09-04 |
Goodmans | 206N/216NS | Line tearing aft 5 mins | Dry joint RC26 , pin 43 of IC501 | 14-09-04 |
Goodmans | 206N/216NS | Menu blank on screen | Main micro locked ou - enter service mode with service reote then exit to reset micro | 14-09-04 |
Goodmans | 206N/216NS | Tripping | R804 0R56 2w fusible o/c after a s/c in LOP stage fixed | 14-09-04 |
|
Goodmans | 206N/216NS | Tripping with burning smell | FOP chip TDA8356 | 14-09-04 |
Goodmans | 206N/216NS | Txt - no G - ok on pic | D702 1N4148 o/c | 14-09-04 |
Goodmans | 206NS | Blank raster | Jungle IC | 14-09-04 |
Goodmans | 206NS | Blank raster, no sound, osg or r/c when first switched on (OK after re-switched on) | Earth speakers/grill to crt rimband | 14-09-04 |
Goodmans | 206NS | DEAD. F801 BLOWN | IC801 REGULATOR FAULTY | 14-09-04 |
Goodmans | 206NS | LINE TEARING AFTER WARM UP | POSSIBLE DRY JOINTS ON IC501 | 14-09-04 |
Goodmans | 206NS | NO GREEN ON TELETEXT PICTURE OK | REPLACE D702 1N4048 | 14-09-04 |
Goodmans | 206NS Daewoo CP380 | Short/dark pic | Enter service mode to adj - special handset reqd R-305VC - buy, beg or borrow! | 14-09-04 |