| Make | Model | Problem | Solution | Date |
| | | |
| Found: 33
|
| Akai | CT2125 | Comes on with chirping noise & st/by led on then trips out after 1/2 min | C817 100µ 25v | 14-09-04 |
| Akai | CT2125 | Int blank raster with fb lines | OK when con TD203 on txt pcb removed - TZ01 27Mhz Xtal | 14-09-04 |
|
|
| Beko | 17125T | Dead - LOPTr s/c - used S2055N | C140 .022µ 400v Was o/c | 14-09-04 |
| Beko | 17125T | Severe E-W bowing | lopt 11.1,110 CPC TFHR8007 | 14-09-04 |
| Beko | NR17125T | Blows LOPTr after a few days | Check C140 22nF for o/c - upgrade to 1000vw | 14-09-04 |
| Decca | 125 | Cramped frame after 2 hours. | R813 ( 10k ) set HT control int. | 14-09-04 |
| Decca | 125 | Frame collapse. | IC301 ( TDA1170S ) s/c , R434 ( 10R ) o/c. | 14-09-04 |
| Decca | 125 | Line hold critical - wavering at top of pic. | IC TDA2576A , C406 ( 22uf 16v ) | 14-09-04 |
| Decca | 125 | No colour. | C517 ( 100nf ) leaky. | 14-09-04 |
| Decca | 125 | No luminance. | C514 ( 100nf ) leaky. | 14-09-04 |
| Decca | 125 | Poor contrast - control has no effect. | R425 , R426 ( 68k ) high. | 14-09-04 |
| Decca | 125 | Will not switch to standby via remote control | IC SAA1351. | 14-09-04 |
| Finlux | 5125 | Dead - MOSFET IBRC40 s/c wickman fuse 1.6A o/c | Fitted BUZ91 & TDA4605 - no other ff (HT correct at 142v) | 14-09-04 |
| Hitachi | C2125T 11AK19K | Dead aft it went pop | D812 BYD33D s/c in 14v supply | 14-09-04 |
| Hitachi | C2125T 11AK19Y4 | St/by only | Handset was faulty even though it gave an o/p | 14-09-04 |
| Mitsubishi | CT2125TX | Dead - standby light flashing. | HT @ 35v , D961 ( 6.2v zener ) leaky. | 14-09-04 |
| Mitsubishi | CT2125TX | Dead. | D909 ( 3v zener ) s/c. | 14-09-04 |
| Mitsubishi | CT2125TX | Int blowing line transistor. | STR54041 , clean & resolder pins of line driver transformer. | 14-09-04 |
| Mitsubishi | CT2125TX | Large black square int covers screen, floats left or right & int poor contrast | C959 100µ 25v hi esr causing low 5v supply from reg - also check C964 10µ 50v, C962 100µ 50v, C905 470µ 25v | 14-09-04 |
| Mitsubishi | CT2125TX | No sound mute. | D361 ( 1N4148 ) | 14-09-04 |
| Mitsubishi | CT2125TX | No video | Z951 630ma fusible link in 8.5v line on psu | 14-09-04 |
| Mitsubishi | CT2125TX | SLIGHTLY OFF TUNE | REPLACE IC101 | 14-09-04 |
|
|
| Mitsubishi | CT2125TX | Sound - will not tune right down or mute. | D361 ( 1N4148 ) leaky. | 14-09-04 |
| Mitsubishi | CT2125TX | Sound wont go off | Pin 4 audio chip hi at 2.3v (0.3v) - D361 1N4001 leaky | 14-09-04 |
| Mitsubishi | CT2125TX | Tuning slightly off - unable to fine tune | IC101 MS1496P | 14-09-04 |
| Mitsubishi | CT2125TX | user settings wont store | minus30v pin 2 eeprom IC702 low. C962 leaky also check other electros | 14-09-04 |
| Philips | 21CE1259 | Dead with buzzing | Loptx s/c | 14-09-04 |
| Philips | 37TR125 | Key set | The key set assy has been codified for all b-range tvcr's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11076.
Key set for: 37TR120/01/08 - 37TR126/03/38 - 37TR125/38N - 37TVB10/39N. | 14-09-04 |
| Philips | 37TR125/38 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05, 14PV163/05H, 14PV263/01 | 14-09-04 |
| Philips | CP90 21CE1259/05B | Int lines on screen esp from cold | Check / replace caps in IF can | 14-09-04 |