| Make | Model | Problem | Solution | Date |
| | | |
| Found: 119
|
| Goldstar | CF25C28CF | Field collapse | Fit kit which contains TDA8350QN5 (don't use TDA8350Q) | 14-09-04 |
| Goldstar | CF25C28F | E-W Dist | Q351 KTB988Y s/c e-c & FR359 22R ?w fus res high | 14-09-04 |
|
|
| Goldstar | CF25C28F | Field collapse | IC351 TDA8350Q & mod kit KITPC58A | 14-09-04 |
| Goldstar | CF28C28F | Field collapse | Replace IC351 TDA8350CQ fop chip & check adequate heatsink compound & clip is secure | 14-09-04 |
| Grundig | CUC2800 | Arcing from LOPTx former to adjacent components | Tripler faulty | 14-09-04 |
| Grundig | CUC2800 | Dead - psu working ok | Relay contacts | 14-09-04 |
| Grundig | CUC2800 | No sound | Check TDA6200 sound proc & U2829B sound dem chip | 14-09-04 |
| Grundig | CUC2800 | Sound from one chan only & no brill adj | Micro SDA2011-A005 faulty | 14-09-04 |
| Grundig | CUC2800 | Sound low & dist | U2829B IC sound chip | 14-09-04 |
| Grundig | CUC2800 | The tripler had failed. After replacing it the set | Microcontroller chip type SDA2011 -AOO5 . Make sure that you get the right one for the set. | 14-09-04 |
| Hitachi | C2524R/C2824R | Dead - psu blow up | Replace R761, 762, 766 all 2R2, R909, R902, R901, C906, C908, ZD903, ZD901, ZD902, LOPTr 2SD1884 & chopper Tr BUT12AF | 14-09-04 |
| Hitachi | C2574TN C2874TN | Shuts down with only NICAM leds lit | R952 68k, R953 82k, R954 8k2 in PSU | 14-09-04 |
| Hitachi | C2808 | Int lh chan sound | C420 470µ spkr coupling cap o/c | 14-09-04 |
| Hitachi | C28300 | No luminance when switched on after being left in st/by for a while | SAA4981 IC1300 on 16:9 sub panel | 14-09-04 |
| Hitachi | C28300,C2576TN etc A5 chassis | Field lin & lines at top of pic | C725 33nF 400v | 14-09-04 |
| Hitachi | C28300,C2576TN etc A5 chassis | Int trips & lines | C719 4µ7 250v smoothing cap for 200v in E-W corr & check joints T702 (under plastic strut) & R950 68k near HT pot | 14-09-04 |
| Hitachi | C28300,C2576TN etc A5 chassis | Red pic with fb lines | R829 fusible on crt base o/c (not shown on cct diag) | 14-09-04 |
| Hitachi | C28300TN A5 | Long time for pic to appear & white bands across | C954 1000µ 35v in 12.6v supply | 14-09-04 |
| Hitachi | C2842N 11AK19PP | Dead - D823 blown (not shown on cct) | When replaced still faulty, IC802 MC44604P chopper chip u/s - also check FET chopper Tr | 14-09-04 |
| Hitachi | C2846 | Field collapse | IC601 (TA8427K) + 26v rail supply R710 (2R0 safety) | 14-09-04 |
| Hitachi | C2846TN | Field - lines at top of pic | TA8427K field chip | 14-09-04 |
| Hitachi | C2846TN | Field collapse | R710 2R in FOP supply o/c | 14-09-04 |
|
|
| Hitachi | C2846TN | Field collapse | TA 8427K and 2R0 safety res | 14-09-04 |
| Hitachi | C2846TN | Model no displayed (factory mode) | Press both rec buttons on hset, sw to st/by & then sw off at mains. Wait 30secs b4 sw back on. | 14-09-04 |
| Hitachi | C2846TN | MODEL OF TV DISPLAYED ON SCREEN | PRESS BOTH RECORD BUTTONS ON REMOTE SWITCH TO STANDBY THEN SWITCH OFF AT SET WAIT 30SECS THEN SWITCH BACK ON | 14-09-04 |
| Hitachi | C2846TN | No sound | EEPROM corrupt due to dry joints on regs - replacement pt no E730045 | 14-09-04 |
| Hitachi | C2846TN | No sound - ok thro scart | EEPROM faulty | 14-09-04 |
| Hitachi | C2846TN | No sound (AV sound ok) | IC002 24C04 memory chip | 14-09-04 |
| Hitachi | C2846TN | No Sound via off air or scart | Replace IC002 24C04 (Programmed with correct file) | 14-09-04 |
| Hitachi | C2846TN | Removing Code “C46TN” from screen | TV in factory set up mode - Using RCU, press two VCR REC buttons together. The MENU will appear, then switch to standby. Turn appliance back
on and prompt should have disappeared. | 14-09-04 |