| Make | Model | Problem | Solution | Date |
| | | |
| Found: 58
|
| Blaupunkt | IS32 | Int goes blank with fb lines then trips off | Chopper tfmr int o/c winding | 14-09-04 |
| ITT | PICO S3 | DEAD IF SCAN COILS DISCONNECTED TRIES TO RUN | WIDTH CCT ON SCAN COILS SC | 14-09-04 |
| ITT | PICO S3 | STBY LED FLICKERS BUT DEAD . PIN 4 LOPTX REMOVED P | LOPTX US | 14-09-04 |
| ITT | Pico S3 | Dead - life restored if scan coils dis'd | Width control coil on scan coils has shorted turns | 14-09-04 |
| ITT | Pico S3 | Dead apart from brief led flicker at sw on | LOPTx | 14-09-04 |
| Loewe Opta | ARTS35 66472 | SOUND MOTORBOATS WHEN COLD | C671 1000uF 16v ALSO C675 | 14-09-04 |
| Panasonic | T14S3T | Poor/rolling pic - vid inverted | Replacing IC601 made no difference - IC1205 EEPROM faulty | 14-09-04 |
| Panasonic | TC1S3R | No colour | memory IC , part number XL24C02P-BAA position IC1205 | 14-09-04 |
| Panasonic | TC1S3R | To enter service mode | Select programme 60,( It helps if you tune in to a channel first) & set sharpness to MIN. Press Off Timer button on R/C & at same time press /(down) button on set, this will place TV into service mode. Press the / / / buttons to step up / down
through the functions. Press the + / - buttons to alter the function values. Press the store button after each adjustment has been made to the required values. To Exit service mode press the normalisation button. | 14-09-04 |
| Panasonic | TX14S3T | Dead - if replacing STR chopper chip | Ensure replacement has "A" suffix | 14-09-04 |
|
|
| Panasonic | TX21S3T | Dead - no HT to IC601 | Check D861 for o/c | 14-09-04 |
| Panasonic | TX21S3T | Dead & buzzing | D861 faulty - checks ok out of cct | 14-09-04 |
| Panasonic | TX21S3T | Lack of height | Adj in service mode | 14-09-04 |
| Panasonic | TX21S3T | NEGATIVE PICTURE WITH AGC OVERLOAD ON TUNER PICTURES OK FROM SCART | REPLACE EEPROM (STORE PREVIOUS DATA VALUES AND THEN ENTER INTO NEW CHIP | 14-09-04 |
| Panasonic | TX21S3T | No sound - ok thro scart I/p | No o/p from IC601 - chip faulty | 14-09-04 |
| Panasonic | TX21S3T | Service mode entering | select chanel 60 set sharpness to minimum press timer on remote at the same time as the down arrow on the front of the set - press store after each adj to store | 14-09-04 |
| Panasonic | TX21S3T | Whistle only | Dist line drive wfrm - Pin 9 IC601 only 3.7v (8v); D861 1SS133T-77 hi res | 14-09-04 |
| Panasonic | Z5 TX14S3T | Service mode access | select ch60 "AND set sharpness to minimum." Press off timer on remote as well as V down on TV. Use V up & down to step through functions. Press +/- to alter values.
Press STORE button after each adjustment is made to exit press norm button. | 14-09-04 |
| Panasonic | Z7 TC14S3R | Self check proc | Press F button & Vol - button on set & status on r/c at same time. When complete sw off set then on again & retune | 14-09-04 |
| Panasonic | Z7 TC14S3R | Weak neg pic - as tho in wrong system | EEPROM IC1205 pt no XL24D02P-AA1 corrupted - needs self checking once fitted | 14-09-04 |
| Panasonic | Z7 TC14S3R/T | stuck in stby | MICRO IC1201 IN PROTECT DUE TO NO +2.6V ON PIN31, R1218 620K 0.5W O/C | 14-09-04 |
| Panasonic | Z7 TC21S3R | switched to 16:9 mode | CORRUPT EEPROM (NO OPTION CODE) , REPLACE MICRO IC1201 AND EAROM IC1205, INITIALISE BY PRESSING STATUS KEY ON REMOTE, FOLLOWED BY 'V' BUTTON ON TV | 14-09-04 |
| Panasonic | Z7 TX14S3 | blank raster, sound OK | R560 300K O/C | 14-09-04 |
| Panasonic | Z7 TX14S3 | dead, stby LED is low | 5V STBY RAIL ONLY 2V, D1202 O/C (1N4150T77) | 14-09-04 |
| Panasonic | Z7 TX14S3 | distorted pic and sound, appears to have no sync | EPROM IC1205 (XL24D02PAA1) | 14-09-04 |
| Panasonic | Z7 TX14S3T | Wont find chans in chan search, those already tuned in are off tune & dist. Tall, flat & greyscale off in AV mode | eeprom Part number XL24CO20-AA cured the faults. Caused by dry joint on LOPTx earth tag corrupting EEPROM. Go into"self check" mode. Done by pressing Status button on the remote & V down on set. Shows OPT O2 on screen.Can't store PP until done | 14-09-04 |
| Panasonic | Z7 TX21S3 | stuck in stby | NO 2.6V TO PIN 31 IC1201(Micro), R1218 O/C FUSIBLE 560K 0.5W PART NO. ERO50PKF5603 | 14-09-04 |
| Panasonic | Z7 TX21S3T | goes to stby after 5-10 mins | D1208 MA170 LEAKY | 14-09-04 |
| Panasonic | Z7 TX21S3T | int. startup, int. blank raster, int. no remote operation | LOW SDA/SCL LINES, D307 BZY88C4V7 LEAKY | 14-09-04 |
| Panasonic | Z7 TX21S3T | negative pic with AGC overload via tiner (OK via SCART) | FAULTY EPROM. BEFORE REPLACING ENTER SERVICE MODE AND WRITE DOWN EPROM VALUES.CHANGE IC AND ENTER ORIG.VALUES, YOU MUST ENTER "SHIPPING CONDITION AUTOTUNE" | 14-09-04 |