datasheet,schematic,electronic components, service manual,repairs,tv,monitor,service menu,pcb design
Schematics 4 Free
Service manuals, schematics, documentation, programs, electronics, hobby ....
(welcome to eserviceinfo.com at 21 Nov 12:35 am GMT)

[news] Check out the Pinout Forum [/news]
Login:
Password:

[registration] [send password]
Bulgarian - schematics repairs service manuals English - schematics repairs service manuals Russian - schematics repairs service manuals           back - schematics, service manuals, datasheets forward - schematics, service manuals, datasheetsSearchBrowseUploadMostWantedLinksForumInfo/Contacts
DatasheetsChassis2modelRepair tipsFulltext searchCables & Connectors
Repair tips  

Electronic appliance repair tips database - TV (LCD,TFT,Plasma,Digital), Monitor, VCR, DVD recorder and player, Digital camera, Audio equipment, Microwave ovens, Phone systems, Computer repair

MakeModelProblemSolutionAddedDate
 
Found: 917
SonyKV29F2SET COMES ON WITH FLYBACK LINES THEN GOES DEADREPLACE Q707 (GREEN) Q710 (BLUE) OR Q704 (RED)plamensl14-09-2004
SonyKV29F3UTo enter service modepress following buttons on remote slowly in sequence + (osd button), 5, vol+, TV and it will switch on in test mode 1 press menu on the remote next--power off to quitplamensl14-09-2004
SonyKV29FL1UTripping with LOPTr Q802 s/cDry joints R816 1k 3w & around line dr trfmrplamensl14-09-2004
SonyKV29LS30Dead - LED flashes 11 timesLOPTr BU2515DX s/c - dry joints line dr trfmrplamensl14-09-2004
SonyKV29X1INT BLANK SCREENREPLACE A BOARDplamensl14-09-2004
SonyKV32DX30UWhen replacing LOPTxDon't use pt no listed in manual - wrecks crt - use Part No 145330841.plamensl14-09-2004
SonyKV32WS3UFaint pic, OSG & sound - menu functs work but no stereo optionEEPROM corrupted - reset data & mod (sorry no info on doing this!)plamensl14-09-2004
SonyKV3410BBU508 blown - getting hot.Check value from supply control ( HT? ) pot to 135v rail , gone high.plamensl14-09-2004
SonyKV35v36Sony picture goes out every 15 to 30 minutes, but the sound stays on. Then I just turn it the set off, then it on, and it stays on again for 15 to 30 minutes. Often these errors are related to a bad solder joint on the main-pcb or crt-board. You can check this by [b:5e367dc780]gentley[/b:5e367dc780] tapping on some parts on these pc's with an isolated screwdriver. Whenever you tap, and the picture goes dark, you're sure it's a bad solder joint and you'll need to re-solder it. Anonymous04-07-2005
SonyKV36FS76USleep timer operates 2 mins too earlyMod req - IC107 pt no 680230304plamensl14-09-2004
SonyKVA2542DEADCHECK CIRCUIT PROTECTORS PS682 AND PS681plamensl14-09-2004
SonyKVA2922TrippingC605 220µ in psu low capplamensl14-09-2004
SonyKVA2932UGarbled Txt chars briefly at sw on - no menu/textX2001 on M boardplamensl14-09-2004
SonyKVA2942SFOR VERTICAL SHIFT AND HEIGHT PROBLEMSENTER SERVICE MODE AND MAKE SURE "GEOMETRY SET" IS OFFplamensl14-09-2004
SonyKVA2942UVol intermittentR627 27R hi resplamensl14-09-2004
SonyKVB2923ENo pic or LED at sw on - EHT present. On entering a command LED blinks rapidly 3/4 timesPossible CRT low emiss - try decreasing value CRT heater ballast res to checkplamensl14-09-2004
SonyKVC252IDStuck on chan 00Replace EEPROM IC005 SDA 2546. (24C08 is the same.)plamensl14-09-2004
SonyKVC29No pic - sound, HT, crt htrs all okR807 burn up & change diode in series with it (causing leakage)plamensl14-09-2004
SonyKVD2512Nicam int reverts to mono soundNicam buffer tr Q181 JC501 or 2SC2785plamensl14-09-2004
SonyKVD2512SOUND CUTS OUT OR IS DISTORTEDREPLACE C615plamensl14-09-2004
page: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 
Електроника -  Форум електроника -  Technical Translations -  Repairs Forum -  Търси новини -  ManualZone -  electronics circuits
 Electronics Lab -  master-tv -  Schematics Search Engine -  www.electrik.org -  mondetech -  manualsparadise -  Mondetech French
 Jabse.Zero -  Pinout.net -  Търсачка -  Poblizo.com : travel -  Поща от Jabse -  horo.bg -  Ytpo.net -  Peg Perego

script execution: 0.07 s