Text preview for : disassem_nv.pdf part of panasonic disassem nv panasonic Cam NV-GS6 NV-GS6EE disassem_nv.pdf
Back to : disassem_nv.pdf | Home
MAIN PARTS PORTION
STEP Ref. Section
PART REMOVE NOTE
No. No. No.
1 52 Top Unit 1 4 433, 541 1
Side Case R & 2 450, 4 533 ,
2 -
LCD Ass'y 1 FP7, FP8 2
533 , FP11 or FP9
3 12 EVF Unit 1 (For model with Color EVF) 3
2 433, 450 , 533, 533
4 11 Rear Case Unit 1 (For model with S-VIDEO) 4
P1, (L-1)
5 - Lens Ass'y 1 2 533 , FP301,
5
FP701
6 - Front Case Ass'y & 1 3 433 , FP6, B1 6
Bottom Case Ass'y
2 450 , FP1,FP2,
7 E10 Main C.B.A. 1 FP3, FP4, FP5, 7
FP10
Mechanism 3 413
8 -
Chassis Ass'y 1 8
9 Cassette Cover -----
2
Unit 1 -
A B C D E F
How to read chart shown above:
A: Order of Procedure steps.
When reassembling, perform steps(s) in reverse order.
B: Ref No.
C: Part to be removed or installed.
D: Section No.
E: Identification of part to be removed, unhooked, unlocked,
released, unplugged, unclamped, or unsoldered.
3 404 = 3 Screws 404 , 2(L-1) = 2 Looking Tabs (L-1)
F: Refer to "Notes in chart."
Note:
1 MAIN PARTS SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied.
And some Ref. No. will be skipped. Be sure to make your
orders of replacement parts according to the parts list.
2. The parts indicated by the dotted line are for Ass'y only
and are not supplied.
3. Disregard Ref. No. suffixes when ordering parts. They are used
to describe parts in "Disassembly/Assembly Procedures" section.
433 -1
Side Case R & LCD Ass'y 533 -2
H 12 533 -2
(NV-GS17EG/EF/E/EP/EB, NV-GS18E, 5
533 -3
NV-GS21EG/EK/E/EP/EB,
NV-GS25GC/GN, NV-GS28GK,
NV-GS35EG/E/EP/EB/GC/GN, NV-GS38GK)
533 -4
433 -4
G
533 -4
433 -1
533 -2
(L-1)
450 -7
450 -4
F
433 -4 533 -5
P1 E10 Lens Ass'y
11
FP10 FP9 or FP301
Mechanism Chassis Ass'y FP11 FP701
FP6
FP4 FP1
E FP2 FP8
FP3 450 -7
533 -5
FP7
B1
433 -1
FP5
52
D
413 -8 541 -1
C
2
433 -6
413 -8
433 -1
B 413 -8
533 -2
433 -6
A Front Case Ass'y & Bottom Case Ass'y
4 450 -2
433 -6 450 -2
1 2 3 4 5 6
FRONT & BOTTOM CASE PORTION
STEP Ref. Section
PART REMOVE NOTE
No. No. No.
1 - Bottom Case Ass'y 2 433 , 450 -
E30 Jack C.B.A. 450 , 2 541
2
- Bottom Angle Ass'y
2 2 541
9
A B C D E F
STEP Ref. Section
PART REMOVE NOTE
No. No. No.
4 533 ,
1 E20 Front C.B.A. 2 Light Shield Sheet
10
(For model with Light)
2 56
Four Eyes Lens 2 ----- 10
3 51 Front Case 2 ----- -
A B C D E F
How to read chart shown above:
A: Order of Procedure steps.
When reassembling, perform steps(s) in reverse order.
B: Ref No.
C: Part to be removed or installed.
D: Section No.
E: Identification of part to be removed, unhooked, unlocked,
released, unplugged, unclamped, or unsoldered.
3 404 = 3 Screws 404 , 2(L-1) = 2 Looking Tabs (L-1)
F: Refer to "Notes in chart."
Note:
2 FRONT AND BOTTOM CASE SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied.
And some Ref. No. will be skipped. Be sure to make your
orders of replacement parts according to the parts list.
2. The parts indicated by the dotted line are for Ass'y only
533 and are not supplied.
3. Disregard Ref. No. suffixes when ordering parts. They are used
to describe parts in "Disassembly/Assembly Procedures" section.
E20
533
703
H
(NV-GS6GC,
57 NV-GS25GC/GN, 56 (NV-GS21EG/EK/E/EP/EB,
704 NV-GS28GK, NV-GS35EG/E/EP/EB/GC/GN,
701 NV-GS35EG/E/EP/EB/GC/GN, NV-GS38GK)
NV-GS38GK)
G 533 705
51
702
708
533
541
F
541
58
(NV-GS21EG/EK/E/EP/EB,
711 NV-GS25GC/GN,
NV-GS28GK, NV-GS35EG/E/EP/EB,
NV-GS35GC/GN, NV-GS38GK)
E
433
60
9
E30
59
542 10
542
D
7
77 73 543
542 55
543 54
6
53
541 75
541
C
Bottom Angle Ass'y
543
76
B
450
71
Bottom Case Ass'y
72
8
A
450
1 2 3 4 5 6
SIDE CASE R & LCD PORTION
STEP Ref. Section
PART REMOVE NOTE
No. No. No.
1 31 Side Case R Unit 3 419 , 457 11
2 33 LCD Case A Unit 3 2 455 , 8(L-1) -
3 32 Shaft Case Unit 3 FP8101 11
E40 LCD Backlight 542, (L-2),
4
C.B.A. 3 FP8102
12
5 34 LCD Case B 3 4(L-3) 12
- LCD Panel Ass'y
6 3 3(L-4) 12
35
LCD Shield Case
Unit
A B C D E F
STEP Ref. Section
PART REMOVE NOTE
No. No. No.
1 42 LCD Panel 3 ----- 13
2 39 Reflect Sheet 3 (L-5) 13
3 37 Lead Light Panel 3 ----- 13
4 38 Diffusion Sheet 3 ----- 13
5 40 BEF Sheet 3 ----- 13
6 41 BEF Sheet A 3 ----- 13
7 36 Panel Holder Unit 3 ----- 13
A B C D E F
How to read chart shown above:
A: Order of Procedure steps.
When reassembling, perform steps(s) in reverse order.
B: Ref No.
C: Part to be removed or installed.
D: Section No.
E: Identification of part to be removed, unhooked, unlocked,
released, unplugged, unclamped, or unsoldered.
3 404 = 3 Screws 404 , 2(L-1) = 2 Looking Tabs (L-1)
F: Refer to "Notes in chart."
Note:
3 SIDE CASE R AND LCD SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied.
And some Ref. No. will be skipped. Be sure to make your
orders of replacement parts according to the parts list.
2. The parts indicated by the dotted line are for Ass'y only
and are not supplied.
3. Disregard Ref. No. suffixes when ordering parts. They are used
to describe parts in "Disassembly/Assembly Procedures" section.
34
H
35
LCD Panel Ass'y
42
G (L-3) 36
A (L-4) 41
(L-5) 40
B (L-3) 38
37
F 39
(L-4)
(L-3)
(L-3)
E40
E
FP8101
33
(L-1)
542 (L-1)
(L-2) FP8102
(L-1) (L-1)
D
A 419
(L-1)
32
31 455 (L-1)
C (L-1)
B 457 (L-1)
455
B
A
1 2 3 4 5 6
CCD & LENS PORTION
STEP Ref. Section
PART REMOVE NOTE
No. No. No.
1 E50 CCD C.B.A. 4 2 536 14
2 64 Filter Rubber 4 ----- 14
3 63 Optical Filter 4 ----- 14
(For model with 20,24X zoom)
4 62
Filter Holder 4 ----- 14
A B C D E F
STEP Ref. Section
PART REMOVE NOTE
No. No. No.
1 65 Zoom Motor Unit 4 2 538 , Unsolder 15
2 538, 533
2 66 Focus Motor Unit 4 (For model with 30X zoom) , 15
Unsolder
A B C D E F
How to read chart shown above:
A: Order of Procedure steps.
When reassembling, perform steps(s) in reverse order.
B: Ref No.
C: Part to be removed or installed.
D: Section No.
E: Identification of part to be removed, unhooked, unlocked,
released, unplugged, unclamped, or unsoldered.
3 404 = 3 Screws 404 , 2(L-1) = 2 Looking Tabs (L-1)
F: Refer to "Notes in chart."
Note:
4 CCD AND LENS SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied.
And some Ref. No. will be skipped. Be sure to make your
orders of replacement parts according to the parts list.
2. The parts indicated by the dotted line are for Ass'y only
and are not supplied.
3. Disregard Ref. No. suffixes when ordering parts. They are used
to describe parts in "Disassembly/Assembly Procedures" section.
LUBRICATION POINTS
When the marked parts are replaced, apply the recommended lubricants
H
or adhesive for better maintenance of the unit.
Mark Kind of Lubricant Availability Part Number
Grease Available from Factroy LSUQ0050
61
G
Lubrication Points
F
E50
536
536 538
538
E 64
66
63
Solder
D (NV-GS6EE/GC,
NV-GS17EG/EF/E/EP/EB, NV-GS18E, 62
NV-GS21EG/EK/E/EP/EB,
533
NV-GS25GC/GN, NV-GS28GK)
(NV-GS35EG/E/EP/EB,
NV-GS35GC/GN,
NV-GS38GK)
538
C
538
Lubrication Points
Solder 65
B
A
1 2 3 4 5 6
EVF PORTION
STEP Ref. Section
PART REMOVE NOTE
No. No. No.
1 16 EVF Slide Piece 5 2 450 16
13 EVF Base Frame
2 5 16
15 EVF Earth Plate 2(L-1)
3 14 EVF Spring 5 450 , (L-2) 17
4 17 EVF F.P.C. 5 FP951 17
A B C D E F
STEP Ref. Section
PART REMOVE NOTE
No. No. No.
1 18 Eye Cap 5 2 524 18
2 23 EVF Lens Unit 5 ----- 19
3 22 Eye Sight Lever 5 ----- 19
A B C D E F
How to read chart shown above:
A: Order of Procedure steps.
When reassembling, perform steps(s) in reverse order.
B: Ref No.
C: Part to be removed or installed.
D: Section No.
E: Identification of part to be removed, unhooked, unlocked,
released, unplugged, unclamped, or unsoldered.
3 404 = 3 Screws 404 , 2(L-1) = 2 Looking Tabs (L-1)
F: Refer to "Notes in chart."
Note:
5 EVF SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied.
And some Ref. No. will be skipped. Be sure to make your
orders of replacement parts according to the parts list.
2. The parts indicated by the dotted line are for Ass'y only
and are not supplied.
3. Disregard Ref. No. suffixes when ordering parts. They are used
to describe parts in "Disassembly/Assembly Procedures" section.
H
18
G
22
EVF Case Ass'y
23 524
F 21
20
524
(L-2)
E
FP951 14
17
450 (not supplied)
D
15
(L-1)
450
C
16
13
B
450
16
A
1 2 3 4 5 6
Notes in chart
1. Removal of Top Unit 2. Installation of Side Case R & LCD Ass'y
1) Open the LCD and the Cassette Cover, then remove 1) Connect the LCD F.P.C. and Side R F.P.C. to the
the 5 Screws (433, 541). Connectors FP7 and FP8 so as not to damage the
2) Slide to extend the EVF. F.P.C.s.
3) Pull and slide the Top Unit carefully. 2) Secure Front Portion and Rear Portion, and tighten 6
Screws (450, 533)
Installation of Top Unit
1) Slide to extend the EVF. Side Case R
2) Insert Portion A of the Top Unit, and slide firmly to
install.
Open Cassette Cover
Top Unit
Portion A
Slide
Shape the inside FP8
FP7
Slide
EVF
Rear
Open LCD Portion 533
Front
Fig. D1
533 Portion
450
450
Fig. D2
3. Installation of EVF Unit 5. Installation of Lens Ass'y
1) Confirm that the EVF F.P.C. is hooked to the Hooking Take care not to damage the motor leads.
Portions on the Bottom. Install the Lens Ass'y with the 2 Bosses and 2 Screws
2) Install the EVF Unit while holding the EVF F.P.C. to (533).
avoid damage of the EVF F.P.C.
Lens Ass'y
Hold EVF F.P.C. EVF Unit
Motor leads
Hooking
Portions
FP9 (For model with Color EVF) Boss Boss
or
FP11 (For model with Monochrome EVF)
Fig. D3
4. Installation of Rear Case Unit FP701 FP301
1) Position connector leads so as not to cover Portion A.
Fig. D5
P1 Rear
Connector Case 6. Removal of Front Case Ass'y & Bottom Ass'y
leads Unit 1) Disconnect the Front F.P.C. from the Connector FP6.
2) Open the Cassette Cover and remove the 3 Screws
(433).
3) Remove both the Front Case Ass'y & Bottom Case
Ass'y and continue to grasp them, while disconnecting
the Connector B1.
Cassette Cover
Portion A
Fig. D4-1
2) Secure the Locking Tab (L-1) of the Rear Case Unit to
install it.
FP6
Rear Case Unit
Front F.P.C.
(L-1) B1
Front Case Ass'y & Bottom Case Ass'y
Fig. D6
Alternative method:
If necessary, the Front Case Ass'y can be removed at first.
533 (For model with S-VIDEO)
Fig. D4-2
7. Installation of Main C.B.A. 8. Installation of Mechanism Chassis Ass'y
Take care not to damage the F.P.C.s. Take care not to damage the F.P.C.s.
1) Connect the Zoom Switch F.P.C. to the Connector 1) After installing the Mechanism Chassis Ass'y, confirm
FP10 on the Main C.B.A. the F.P.C.s are positioned as shown.
2) Connect the F.P.C.s to the connectors on the Main
C.B.A, verifying that the direction of the Flexible Cables
is correct. Refer to "REMOVAL/INSTALLATION OF
F.P.C. FROM NON ZIF (Zero Insertion Force)
CONNECTOR."
3) After installing the Main C.B.A., confirm the F.P.C.s are
positioned as shown.
Cylinder Sub Mechanism Capstan Zoom
F.P.C. F.P.C. F.P.C. Switch
F.P.C.
Mechanism Chassis Ass'y
Head
Amp Mechanism
F.P.C. F.P.C.
Fig. D8-1
Replacement of Mechanism Chassis Ass'y
When replacing the Main Chassis Ass'y or the Cylinder
Unit, be sure to perform the Envelope Output Adjustment.
Refer to "ENVELOPE OUTPUT ADJUSTMENT" in
MECHANICAL ADJUSTMENT.
Fig. D7 Handling Caution of Mechanism Chassis Ass'y
When servicing the Mechanism Chassis Ass'y without the
Cassette Up Unit, do not handle the Sub Chassis of the
Mechanism Chassis Ass'y.
Mechanism Chassis Ass'y
(without Cassette Up Unit)
Sub Chassis
Sub Chassis
Sub Chassis
Fig. D8-2
9. Removal of Jack C.B.A. & Bottom Angle Ass'y 11. Removal of Side Case R Unit
1) Open the L Cover. Open and rotate the LCD to access the 2 Screws (419, 457)
2) Remove the Screw (450) and release the Tripod Portion as shown below, then remove it.
from the hole.
Installation of Side Case R Unit
Installation of Jack C.B.A. & Bottom Angle Ass'y When installing, note to the direction of the Shaft Case
Insert both the Jack C.B.A. & Bottom Angle Ass'y into the Unit. Be sure to install the LCD (Ass'y) into the Side Case
2 slots and secure the Tripod into the hole. R Unit with the LCD rotated as shown. Otherwise, the LCD
open/close switch on the Side Case R Unit will be damaged.
450
Open L Cover
Side Case R Unit
LCD open/close SW.
419
slot
Rotate
slot
hole
Jack C.B.A. & 457
Bottom Angle Ass'y Tripod
LCD (Ass'y) Rotate
Fig. D9
Shaft Case Unit
10. Installation of Front C.B.A.
1) Install the Four Eyes Lens (For model with Light) into
the Front Case. Then, install the Front C.B.A. with 2
bosses of the Four Eyes Lens and 2 Screws (533).
2) Install the Light Shield Sheet with 2 Screws (533).
533
Light Shield Sheet
boss (For model with Light) Fig. D11
Front Case
Four Eyes Lens
(For model with Light)
533 boss (For model with Light)
Front
C.B.A.
533
533
Fig. D10
12. Installation of LCD Backlight C.B.A., LCD Panel Ass'y,
LCD Shield Case Unit, LCD Case B
Use extreme care regarding LEDs when handling the LCD
Backlight C.B.A.
Install in order shown below.
1) Install the LCD Panel Ass'y onto the LCD Shield Case
Unit with the 3 Locking Tabs (L-4) while carefully
bending the LCD F.P.C. at it's base so as not to damage
it.
2) Install the LCD Shield Case into the LCD Case B with
the 4 Locking Tabs (L-3).
3) Install the LCD Backlight C.B.A. onto the LCD Panel
Ass'y with the Locking Tab (L-2).
4) Tighten the Screw (542) while keeping the LCD Backlight
C.B.A. pressed toward the right. Then, connect the
Connector FP8102.
542 LCD Backlight C.B.A.
Press
FP8102
(L-2)
LCD Panel Ass'y
(L-4)
(L-3)
(L-3)
(L-3)
Bend
(L-4)
(L-3)
LCD LCD
Shield
F.P.C. Case
Unit
LCD Case B
boss
Fig. D12
13. Installation of LCD Panel, Reflect Sheet, Lead Light
Panel, Diffusion Sheet, BEF Sheet, BEF Sheet A, Panel
Holder Unit
a. When replacing the LCD Panel, the Diffusion Sheet,
the BEF Sheet and the BEF Sheet A, make sure to
remove the Protection Sheets. Reflect Sheet
To distinguish Sheets from attached Protection adhesive
Sheet: tape
Lead Light Panel
- A blue Protection Sheet is affixed to both faces of the
Diffusion Sheet.
- A yellow Protection Sheet is affixed to both faces of
the BEF Sheet.
- A transparent Protection Sheet is affixed to both
faces of the BEF Sheet A.
Protection Sheet Diffusion Sheet Diffusion Sheet
(blue)
(white)
Protection Sheet BEF Sheet
(yellow) BEF Sheet
(stripe)
BEF Sheet A
Protection Sheet BEF Sheet A
(green) (gray)
slot
(L-5)
Panel Holder Unit slot
b. Use extreme care when handling the LCD Panel, the
Reflect Sheet, the Lead Light Panel, the Diffusion View A hole
Sheet, the BEF Sheet and the BEF Sheet A to avoid
damage, dust, and spots (especially fingerprints, etc.) adhesive
adhesive tape
Install in order shown below. tape hole
1) Install in order the BEF Sheet A, BEF Sheet and
Diffusion Sheet while inserting the corners of each
sheets into the slots of the Panel Holder Unit. cross mark
2) Install the Lead Light Panel while inserting the corners
into the slots of the Panel Holder Unit. LCD Panel
3) Align the Reflect Sheet with the edge of the Panel cross mark
Holder Unit, and install it using adhesive tape on the
Reflect Sheet.
cross mark cross mark
Reflect Sheet adhesive
tape
hole of Panel hole of Panel
Holder Unit View A Holder Unit
Fig. D13-2
Do not touch
the surface of
Panel Holder Unit Lead Light Panel.
Fig. D13-1
4) Install the LCD Panel with adhesive tape so that the
cross marks are positioned in the center of the holes in
the Panel Holder Unit.
14. Removal of CCD C.B.A., Filter Rubber, Optical Filter, 16. Installation of EVF Slide Piece, EVF Base Frame
Filter Holder 1) Pass the EVF F.P.C. through the EVF Base Frame
CAUTION: hole.
1) When removing the CCD C.B.A., take care that the 2) Install the EVF Slide Pieces into the EVF Base Frame
Optical Filter does not fall out. from both sides.
2) Use extreme caution when removing the CCD C.B.A. 3) Slide the EVF Case Ass'y to the end so that the ribs are
as it is easily damaged by static electricity. Use a Wrist inserted into the holes of the EVF Slide Pieces.
Strap while removing and installing. 4) Locate the threaded holes, and tighten the 2 Screws
3) Do not touch the CCD window surface. (450).
Installation of CCD C.B.A., Filter Rubber, Optical Filter, 5) After installing, confirm the EVF moves correctly.
Filter Holder
Install in order shown below. EVF Base Frame hole of EVF
1) Install the Filter Holder (For model with 30X zoom) EVF Case Ass'y rib Slide Piece
correctly.
2) Install the Optical Filter correctly. hole
Note: Make sure that no dust gets on the Optical Filter
or in the Lens Unit. Clean the Optical Filter with lens
cleaning paper dampened with lens cleaner if
necessary.
3) Install the Filter Rubber on the Optical Filter correctly as EVF F.P.C.
shown below.
Note: Make sure that no dust gets on the Filter hole of EVF
Slide rib
Rubber. Slide Piece
4) Install the CCD C.B.A. into the Lens Unit. Then, tighten
the 2 Screws (536).
Note: Do not touch the Lens Surface. Clean the surface
with lens cleaning paper dampened with lens cleaner
if necessary.
(threaded hole) 450
15. Installation of Zoom Motor Unit/Focus Motor Unit
Install the Zoom Motor Unit/Focus Motor Unit so that the
Shaft of the Zoom Motor Unit/Focus Motor Unit is set in the
Holder.
EVF Slide Piece
EVF Base Frame
shaft
Zoom
Motor Fig. D16
Unit
holder
Bosses
Bosses
holder
Focus
Motor
Unit
shaft
Fig. D15
17. Installation of EVF Spring, EVF F.P.C.
1) Insert the EVF F.P.C. into the EVF Spring hole paying
particular attention to the direction.
2) Connect the EVF F.P.C. to Connector FP951.
3) Insert the Locking Tab (L-2) at first, then fit the EVF
Spring in the EVF Case and tighten the Screw (450).
(L-2)
EVF Spring
hole
FP951
EVF F.P.C.
EVF Case
Fit
Fig. D17
18. Removal of Eye Cap
Remove the Eye Cap after removing the 2 Screws (524).
19. Handling cautions of EVF Lens Unit
Use extreme care when handling the EVF Lens Unit to
avoid damage, dust, and spots (especially fingerprints,
etc.)
Installation of EVF Lens Unit, Eye Sight Lever
1) Install the Eye Sight Lever into the EVF Case hole in the
direction shown.
2) Install the EVF Lens Unit into the EVF Case while
grasping both sides of the springs with tweezers, etc.
3) After installing, confirm the Eye Sight Lever and the
EVF Lens Unit work together correctly.
EVF Case
hole
EVF Lens Unit
Bosses
Eye Sight Lever
Spring
Bosses
Spring
Tweezers
Fig. D19