Text preview for : 24gs3-p51-73.pdf part of
| Home
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 51
GS - 107B General Specification (Sheet 590)
FEATURES / BENEFITS
- Extremely high MTBF (over 75K Hours, exclude. CRT).
- User friendly OSD display for mode identification and adjustment
- Professional look, with non-flammable cabinet (94V-0).
- Better display performance.
. Flat/square display tube
. Finer CRT dot pitch (0.26 mm)
. Full screen size application
. Real multi-freq.
. Short-length CRT
- Power saving management system.
- VESA DDC1 /2B
- Picture tilt control
- Low emission TCO99/TCO95/MPR II
A
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 1
99-10-12
52 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
INDEX
=========
1.0 Introduction
2.0 General description
2.1 General condition
3.0 Electrical characteristics
3.1 Signal interface
3.1.1 Input requirements
3.1.2 Signals input.
3.1.3 Factory pre-set modes
3.2 Timing requirements
3.2.1 Horizontal scanning
3.2.2 Vertical scanning
3.3 Power supply
3.4 Power saving management system
3.5 CRT description
3.6 RGB amplifier
3.6.1 Video amplifier
3.6.2 Brightness and contrast
3.7 Variation of image size
3.8 Degaussing
3.9 Phosphor protection
3.10 Low emission requirements (TCO-99/TCO95/MPR-II)
3.11 Display data channel : DDC1/2B (VESA STANDARD)
4.0 Display
4.1 Display resolution
4.2 Image size
4.3 Image centering deviation
4.4 Picture shift control range
4.5 Geometric distortions
4.6 Picture tilt
4.7 Image non-linearity
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 2
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 53
4.8 Mis-covergence
4.9 Focus check
4.10 Luminance uniformity
4.11 White color adjustment
4.12 Color tracking on full white pattern
4.13 Purity
4.14 Moir
5.0 Mechanical characteristics
5.1 User controls ( at front)
5.2 Connector and cables
5.2.1 Power Cord
5.2.2 Signal Cable
5.3 Foot Assembly
6.0 Connector and cable
7.0 Environmental characteristics
7.1 Susceptibility of display to external environment
7.1.1 Operation limits
7.1.2 Transportation packages
A
7.2 Display disturbance from external environment
7.2.1 ESD disturbances
7.3 Display disturbance to external environment
7.3.1 Ionizetic radiation
7.3.2 EMI
8.0 Reliability
8.1 Mean time between failures
9.0 Quality assurance requirements
9.1 Acceptance test
10.0 Serviceability
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 3
99-10-12
54 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
1.0 Introduction
This document is related to the 17" AUTOSCAN color monitor
and max. resolution:
1280 X 1024 by 85HZ refresh rate
2.0 General description
This AUTOSCAN analog colour monitor is specified as a
display peripheral within an IBM compatible PC.
The AUTOSCAN analog colour monitor is to operate at
H: 30 to 92.0 KHz V: 50 to 160 Hz
can be applied to all RGB analog computers within this scanning frequencies.
The AUTOSCAN analog colour monitor is intended to be a
finished product, basically a display device mounted inside
a plastic enclosure which provides the aesthetic, mechanical,
ergonomic and safety requirements.
2.1 General condition
The unit will produce a usable image after switching-on,
measurements are to be carried out with a full stabilised
set after about 30 minutes warm-up at room ambient
temp. of 25C.
Repetitive power on/off cycles are allowed though should
be avoided within 4 sec.
3.0 Electrical characteristics
3.1 Signal interface
This AUTOSCAN analog colour display has an analog video
interface to operates at a multi-frequencies timing in
several display modes.
3.1.1 Input requirements
A. Input signals
Video - 0.7 Vp-p 75 ohms (for individual of R,G and B
signals must not deviate 0.015 Vp-p from each
other for balance of white pattern)
Sync - TTL level
(between 0 and 0.6 V to be considered as low
level, between 2.3 and 5.0 V as high level)
B. Impedance
Video - Terminated with 75 ohms
Sync - Terminated with 4.7K ohms pull-down resistors.
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 4
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 55
3.1.2 Signals input
The input video signals are applied to the display device
through a video cable which is fixed to the monitor
(flying cable length 1.5M).
Video input cable :
15 pin D-shell connector type with pin assignment
as follows :
Pin assignment of 15P D-SUB connector
Pin No. Assignment
P1 Red video input
P2 Green video input
P3 Blue video input
P4 Ground
P5 Self-test
P6 Red video ground
P7 Green video ground
P8 Blue video ground
P9 Not connect
P10 Ground
P11 Ground
P12 Bi-directional data (SDA)
P13 H SYNC
P14 V SYNC
P15 DDC Data CLOCK (SCL)
3.1.3 Factory pre-set modes:
A
PRESET VIDEO RESOLUTION AND SYNC. POLARITIES
Resolution modes V. freq. H. freq. H. V.
1. 800 x 600 75.000 Hz 46.875 KHz + +
2. 800 x 600 85.061 Hz 53.674 KHz + +
3. 1024 x 768 70.069 Hz 56.476 KHz + +
4. 1024 x 768 75.029 Hz 60.023 KHz + +
5. 1024 x 768 84.997 Hz 68.677 KHz + +
6. 1152 x 864 75.000 Hz 67.500 KHz + +
7 1280 x 1024 75.025 Hz 79.976 KHz + +
8. 1280 x 1024 85.024 Hz 91.146 KHz + +
3 .2 Timing requirements
The pre-set timing table are shown as below
Timing Table : 1- 8
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 5
99-10-12
56 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
TIMING FOR GS 107B " 92KHz
(VESA monitor timing standard Version 1.0 Release 0.8)
REFERENCE PATTERN GENERATOR : CHROMA 2200 or2250
TABLE 1: 46.875 KHz/75.000Hz, 800 X 600, pixel=49.500 MHz
Horizontal Vertical
Frame border = 0 Frame border = 0
Total size = 21.333 us Total size = 13.333 ms
Display size = 16.162 us Display size = 12.800 ms
Rear porch = 3.232 us Rear porch = 0.448 ms
Sync width = 1.616 us Sync width = 0.064 ms
Sync polarity = + Sync polarity = +
TABLE 2: 53.674 KHz/85.061Hz, 800 X 600, pixel=56.250 MHz
Horizontal Vertical
Frame border = 0 Frame border = 0
Total size = 18.631 us Total size = 11.756 ms
Display size = 14.222 us Display size = 11.179 ms
Rear porch = 2.702 us Rear porch = 0.503 ms
Sync width = 1.138 us Sync width = 0.056 ms
Sync polarity = + Sync polarity = +
TABLE 3: 56.476 KHz/70.069Hz, 1024X 768, pixel=75.000 MHz
Horizontal Vertical
Frame border = 0 Frame border = 0
Total size = 17.707 us Total size = 14.272 ms
Display size = 13.653 us Display size = 13.599 ms
Rear porch = 1.920 us Rear porch = 0.513 ms
Sync width = 1.813 us Sync width = 0.106 ms
Sync polarity = - Sync polarity = -
TABLE 4: 60.023 KHz/75.029Hz, 1024X 768, pixel=78.750 MHz
Horizontal Vertical
Frame border = 0 Frame border = 0
Total size = 16.660 us Total size = 13.328 ms
Display size = 13.003 us Display size = 12.795 ms
Rear porch = 2.235 us Rear porch = 0.466 ms
Sync width = 1.219 us Sync width = 0.050 ms
Sync polarity = + Sync polarity = +
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 6
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 57
TABLE 5: 68.677 KHz/84.997Hz, 1024X 768, pixel=94.500 MHz
Horizontal Vertical
Frame border= 0 Frame border = 0
Total size = 14.561 us Total size = 11.756 ms
Display size = 10.836 us Display size = 11.183 ms
Rear porch = 2.201 us Rear porch = 0.524 ms
Sync width = 1.016 us Sync width = 0.044 ms
Sync polarity = + Sync polarity = +
TABLE 6: 67.500 KHz/75.000Hz, 1152 X 864, pixel=108.000MHz
Horizontal Vertical
Frame border= 0 Frame border= 0
Total size = 14.815 us Total size = 13.333 ms
Display size = 10.667 us Display size = 12.800 ms
Rear porch = 2.370 us Rear porch = 0.474 ms
Sync width = 1.185 us Sync width = 0.044 ms
Sync polarity = + Sync polarity = +
TABLE 7: 79.976 KHz/75.025Hz, 1280 X1024, pixel=135.000MHz
Horizontal Vertical
Frame border= 0 Frame border= 0
Total size = 12.504 us Total size = 13.329 ms
Display size = 9.481 us Display size = 12.804 ms
Rear porch = 1.837 us Rear porch = 0.475 ms A
Sync width = 1.067 us Sync width = 0.038 ms
Sync polarity = + Sync polarity = +
TABLE 8: 91.146 KHz/85.024Hz, 1280 X 1024, pixel=157.500 MHz
Horizontal Vertical
Frame border= 0 Frame border= 0
Total size = 10.971 us Total size = 11.761 ms
Display size = 8.127 us Display size = 11.235 ms
Rear porch = 1.422 us Rear porch = 0.483 ms
Sync width = 1.016 us Sync width = 0.033 ms
Sync polarity = + Sync polarity = +
3.2.1 Horizontal scanning
Scanning frequency : 30 - 92 KHz,
H-shift range : 20 mm min.
Retrace time : Less than 2.50 us.
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 7
99-10-12
58 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
3.2.2 Vertical scanning
Scanning frequency : 50 - 160 Hz
V-shift range : 10 mm Min.
3.3 Power supply
The display device maintains the specified performance
in the range described as below :
Type Mains current Mains Voltage Mains freq.
1.6A max. 90 - 264 VAC 47-63Hz
Power consumption : 100 Watts Max.
Power cord length : 1.5M
Power cord type : 3 leads detachable power cord with
protective earth plug .
3.4 Power saving management system
SIGNAL POWER RECOVERY
MODE
H-SYNC V-SYNC VIDEO TIME
ON ACTIVE ACTIVE ACTIVE < 100W NA
STAND-BY INACTIVE ACTIVE BLANKED < 15W ~ 3 SEC.
SUSPEND ACTIVE INACTIVE BLANKED < 15W ~ 3 SEC.
OFF INACTIVE INACTIVE BLANKED < 3W ~ 7 SEC
3.5 CRT Description
This display unit employs a high resolution CRT complying
with the following specifications :
Dimensions : 17 inches,(short length)
flat/square screen.
Pitch : 0.26mm dotted
Deflection angle : 100 degrees
Light transmission : 46%
Face treatment : AR-ASC coating
Implosion protection : CRT is provided with P-mini-rim-band
EHT : 26.0KV
Visible screen area : 322 mm x 245 mm
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 8
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 59
3.6 RGB Amplifier
3.6.1 Video amplifiers
Dot Rate : 157.5 MHz
Over / undershoot : 10% Max.
(Transient response)
Sag (background : 5% Max. (pulses of 0.70H)
uniformity)
3.6.2 Brightness and contrast
Reference mode 68.7K/85Hz full white pattern.
Brightness Contrast Light output
(full white)
Minimum Minimum < 1.0 FL
A
Center Maximum 30 5 FL
3.7 Variation of image size
Due to brightness change
from 3 to 30 FL (Max.) : < 1.0 mm
Due to aging
(0 to 40C) : < 1.0 %
Due to mains voltage
variation : < 1.0 %
3.8 Degaussing
An automatic degaussing circuit is provided which req-
uires no intervention. The degaussing activated at the
time of switch-on or switch-on again or pressing manual
degaussing key after switching-off degaussing circuits
for longer than 30 minutes.
3.9 Phosphor protection
The display device is sufficiently protected against the
burning of phosphors in case of repetitive power cycling
or absence of horizontal deflection.
3.10 Low emission requirements (TCO-99)
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 9
99-10-12
60 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
Items Band I Band II
ELF (rms) VLF (rms)
Alternating Electric MPR-II 25 V/M MPR-II 2.5V/M
Field TCO-9510 TCO-951.0
Magnetic Field MPR-II 250 nT MPR-II 25 nT
TCO-95 200 nT TCO-9525 nT
E.S.P 500 V
Band I : 5 to 2K Hz.
Band II : 2K to 400K Hz.
Test procedure according to Low emission test method.
3.11 Display data channel : DDC1/2B (VESA STANDARD)
The DDC HEX Data should be written into DDC memory inside
the CPU IC (7802) by EEPROM writer or equivalent method.
4.0 Display image (CRT facing east)
The monitor is aligned in a magnetic cage having the
following magnetic field components :
Northern Hemisphere : H = 0, V = +0.43 +/- 0.05G, Z = 0
Southern Hemisphere : H = 0, V = -0.52 +/- 0.05G, Z = 0
Conditions for visual testing, unless otherwise stated:
Input video signal - 700 mVp-p cross hatch
Brightness control - 50%
Contrast control - Adjusted to 30 5 FL of luminance
with full white pattern
4.1 Display resolutions
See 3.1.3
4.2 Image size (Factory pre-set modes only)
The dimensions of guaranteed display area to be measured
along the picture center of horizontal and vertical axis
of the screen as listed below: (preset modes only, refer
to fig. 1/fig 2)
Width : 306 +/- 3 mm .(fig 1)
Height : 230 +/- 3 mm .(fig 1)
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 10
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 61
4.3 Image centering deviation (Factory preset modes only)
With respect to fig. 2, the target relationships are
the following :
|A - B| <= 5 mm |C - D| <= 5 mm
Note : This centering is adjustable by the end-user.
4.4 Picture shift control range
H-shift range : 20 mm min. (+/- 5mm,from center to each side)
V-shift range : 10 mm min. (+/- 2mm,from center to each side)
4.5 Picture tilt
With respect to Fig. 3, Tilt to be measured on extremes
of center line from bezel.
Tilt : < = 2 mm
4.6 Geometric distortions
It is acceptable that pincushion, trapezoid, rhomboid,
rotation and various waves distortions must remain within
the limits of tolerance as in fig. 4,
| A |, | B | 2.0mm
| C |, | D | 2.0mm
The waviness of any vertical or horizontal shall be less
than 1.0 mm over a 50 mm distance.
4.7 Image non-linearity pattern with
10 equal blocks along horizontal axis,
8 equal blocks along vertical axis.
Overall : <= 10 % (each horizontal and vertical)
Xmax. - Xmin
H. linearity = ----------------------- x 100%
Xmax.
Ymax. - Ymin
V. linearity = ------------------------ x 100%
Ymax.
4.8 Mis-convergence
The maximum convergence error to be measured on a white
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 11
99-10-12
62 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
spot or white display line to represents the maximum distance
between the energy centers of any two primary colors. (See Fig. 6)
Mis-Convergence SPEC.
CRT Pitch 0.26mm
Zone A 0.30
Zone B 0.40
Center 0.15
4.9 Focus check (with 79.99KHz/75Hz,1280 x 1024 mode)
Generate "@" characters (pattern as fig 7)to cover entire of the picture
area (display size respect to fig. 1), adjust brightness
control to click and contrast near center (~ 30 FL full white )
the characters should be clearly identified in
all display area.
4.10 Luminance uniformity
condition : With full white pattern, set contrast control
at max. and adjust brightness control
to get 30FL in center..
the max. deviation to the rest of the screen shall not exceed 25% of entire
screen with any point.
4.11 White color adjustment
Based on the 1931 CIE chromaticity (colour triangle)
diagram (x,y coordination).
coordination of white display on screen center should be:
for 9300 degreeK X = 0.283 +/- 0.015
Y = 0.297 +/- 0.015
for 6500 degreeK X = 0.313 +/- 0.015
Y = 0.329 +/- 0.015
Check conditions :
Set brightness control at 50% position and contrass at maximum.
4.12 Color tracking on full white pattern
Ref. to white balance alignment result and set brightness at 50%, adjust
contrast control from 5FL to max. position, the colour coordinate
should not deviate more than following tolerance when
compare to display center:
X= X nominal +/- 0.015
Y= Y nominal +/- 0.015
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 12
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 63
4.13 Purity
Test patterns : Full White
Conditions:As stated in item 4.0, the purity must be
checked under specific destinations of earth
magnetic environments and the monitor to be
well degaussed.
After warming-up time of 30 min., no coloured stains may
occur in above four patterns.
4.14 Moir
Condition: Displaying a full white pattern, at any pre-set
mode the display size of the sets to be set
as stated in "Fig. 1".
No serious moir'e is visible after adjustment via OSD moir control
function and test is to set brightness at center(50%),contrast at Max
. However the OSD moir data of V-moir should be default 30 for outgoing
product .Increasing the moir control value will have side effect on
resolution (degrade focus),and phenomenon of flicker and sawtooth.
5.0 Mechanical characteristics
5.1 User controls (all at front) Right to left
- Power ON/OFF
- Enter
- Up/Down
- Right
- Left
6 .0 Connectors and cables
6.1.1 Power cord (plugable) type : Wall Plug ,non shielded and non-attached.
Length : 1.5 m +/- 50 mm . Plug curved at 90.
6.1.2 Signal cable
Length of video : 1.5 m +/- 50 mm flying in 15pins D-shell.
7.0 Environmental characteristics
The following sections to define the interference and
susceptibility condition limits that might occur between
external environment and the display device.
7.1 Susceptibility of display to external environment
7.1.1 Operating limits
A). Temperature : 0C to 40C
Humidity : 10 to 90% (W/O condensation)
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 13
99-10-12
64 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
Air pressure : 700 ~ 1100 mbar
B). Non-operating limits (storage)
Temperature : -25C to 65C
Humidity : 5 to 95 % (W/O condensation)
Altitude : 300 to 1100 mbar
7.1.2 Transportation packages
A) Carton box
: 541(W) x 525 (H) x 494 (D) mm.
B) Transportation conditions
(see table, shown as below)
B-1 Transportation standards
TEST Standard reference Philips severity Remarks
Drop Gross weight Drop height *W/O 10% drop
1C-3E-6F (Kg) (cm) height increment
NSTA
18.60 ~27.66 61
Random vibration Truck spectrum, 0.73 Grms,
30 min/axis, 3 axes
Shock - 1/2 sine pulse: Design stage
(non-oper) 100G<3ms, 6 shocks only.
- Square pulse:
35G, 4.2mps, 6 shocks for
screen size up to 15 ,
30G for 17 mointor.
- Damage boundary curve:
* CRT supplier spec. is used
to define maximum
acceptable CRT fragility.
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 14
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 65
B-2 Container loading
Container size
40Feet 20Feet High cube 40 Feet
Q'ty W/Pallet W/Pallet W/Pallet
Yes No Yes No Yes No
Layers 4 4 4 4 4 4
Sets per layer 4 4 4 4 4 4
Sets per block 16 16 16 16 16 16
Blocks per container 24 24 10 10 24 24
Total set 384 384 160 160 384 384
7.2 Display disturbances from external environment
7.2.1 ESD Disturbances
According to IEC65 (also refer to IEC801-2 for detail).
7.3 Display disturbances to external environment
The disturbances induced by the display and tolerated
by the environment are defined as follows :
7.3.1 Ionizetic radiation
Completely fulfilled International Commission of
Radio logical Protection (ICRP) requirement 0.5 mr/hrs.
Actually the set can reach 0.1 mr/hrs.
7.3.2 Safety and EMI requirements
------------------------------------
Safety - USA :UL 1950
-CANADA :CSA C22.2 NO.950-M89
-NORDIC :IEC950
:EN60950
:EMKO TSE (74SEC) 207/94
-GERMANY :ZHI/618 (GS)
:ISO 9241-3, 9241-8
EMI -USA :FCC PART 15 Class B
-CANADA :D.O.C. Class B
-CE :EN55022 CLASS B
-JAPAN :VCCI Class B
EMS -CE :EN50082-1
:EN60555-2
LOW EMISSION :MPR II
:TCO95
:TCO99
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 15
99-10-12
66 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
7.3.3 X-RAY radiation requirement /regulation
-USA/CANADA :DHHS 21 CFR, CHAPTER 1,SUBCHAPTER J
-GERMANY :RONTGEN VERORDNUNG ROV 1987.01.08
X-ray explosure at 5cm distance from any point of the external surface must not exceed
0.1 mR/H.
8.0 Reliability
8.1 Mean time between failures
MTBF to be calculated according to Military standard
MIL-HDBK-217C.
MTBF >=75,000 Hours (Excluding CRT)
TOTAL HRS (POWER ON) X TOTAL SETS
PRACTICE of MTBF = ---------------------------------------------------------
NBR. OF FAILURED SETS
9.0 Quality assurance requirements
9.1 Acceptance test
According to MIL-STD-105D level II,
AQL : 0.65 (Major)
2.5 (Minor)
Customer acceptance :
criteria : UAW0377/00
10.0 Serviceability
The service ability of this monitor should fulfill the
requirements which are prescribed in UAW-0346 and
must be checked with the check list UAT-0361.
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 16
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 67
233 mm
227 mm
230 mm
303 mm
306 mm
309 mm
FIG-1 IMAGE DIMENSION
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 17
99-10-12
68 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
C
230 mm
A B
D
306 mm
|A-B| AND |C-D| < 5 mm
FIG-2 IMAGE CENTERING
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 18
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 69
B
A
306 mm
|A-B| < 2 mm
FIG-3 IMAGE ROTATION
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 19
99-10-12
70 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
C
A B
230 mm
D
306 mm
A, B <= 2.0 mm C, D <= 2.0 mm
FIG-4 IMAGE GEOMETRY
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 20
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 71
80 mm
230 mm
80 mm
Pattern B
Pattern A
306 mm
FIG-5 CONTRAST AND BRIGHTNESS
MEASUREMENT PATTERNS
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 21
99-10-12
72 107B CM24 GSIII GENERAL PRODUCT SPECIFICATION
ZONE B
230 mm
306 mm
FIG-6 MISCONVERGENCE
MEASUREMENT AREA
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 22
99-10-12
GENERAL PRODUCT SPECIFICATION 107B CM24 GSIII 73
CHARACTER
FOR FOCUS
( CHROMA 2200/2250 CHR NO. 56 )
FIG - 7
17" AUTO SCAN CMTR
TYPE : 107B10/20-CM24-GS3
8639 000 10284
99-10-12 BRAND : PHILIPS (107B+)
TONY HSUI/Y.H.HSU 23 590 23
99-10-12