Text preview for : bryston_10b_xo_sch.pdf part of . Various bryston 10b xo sch . Various SM scena Bryston bryston_10b_xo_sch.pdf
Back to : bryston_10b_xo_sch.pdf | Home
BRYSTON SST
PERFORMANCE DRIVEN
10 B ELECTRONIC CROSSOVER
Bryston's Model 10B Electronic Crossover combines ideal frequencies more suitable to sub-woofer applications and a
signal-handling with an enormously flexible control function. 10B standard which is more applicable to speakers reacquiring
Simple, direct front-panel switches allow any crossover curve frequency control in the midband and tweeter areas.
to be set instantly, and the signal purity is always maintained.
All crossover selections are extremely accurate and repeatable,
The Model 10B features independently selectable crossover being implemented with 1% selected metal-film resistors
points for high-pass and low-pass, in case the speaker installation and polystyrene capacitors. All switches are heavily gold-
requires slightly overlapped, (or slightly staggered), response plated, for lifetime protection from corrosion. The level-
curves for the drivers. You can also independently select controls are precise 1dB increments, also derived from
crossover slope, from 6, 12, or 18dB/Oct., where one driver gold-plated switches and 1% metal-film resistors. Most
requires raster cutoff than another in the same system. important, however, is that the Bryston 10B Crossover uses
NO integrated circuits in the signal path. All internal buffer
MODEL 10B LR and amplification stages are Bryston's exceedingly linear and
The 10B-LR, a fixed f requency plug in Linkwitz-Riley superbly quiet discrete op-amp circuitry. This means the
alignment with steep roll off curves of 24 dB/Oct. is signal is always maintained as "Audiophile Quality", with
also available. stability and freedom from noise and distortion unapproached
in other crossovers.
The crossover may be used in any of three connections: 2-way
stereo, 3-way mono, and a special configuration, 2-way stereo with From the point of view of adaptability, flexibility and signal
summed low pass out to allow the use of one sub-woofer. The integrity, the Bryston 10B Electronic Crossover is the ideal choice
10B is available in two stock versions, a 10B sub incorporating for the widest range of multi-way speaker installations.
1
10B SWITCHING AND CONNECTIONS
(B) (C) (D) (E) (F) (A) (G) (H) (A) (B) (C) (D) (E) (F) (A)
(I) (J) (K) (L) (K) (J) (I)
(A) MUTE SWITCH (F) HIGH PASS FREQUENCY SELECTOR
One each for low pass and high pass filters 12 selectable crossover points
(B) LOW PASS FREQUENCY SELECTOR (G) STATUS LEDS
12 selectable crossover points
(H) POWER SWITCH (PUSH BUTTON)
(C) LOW PASS SLOPE SELECTOR
(I) INPUT RCA OR XLR (FEMALE)
Sets low pass slope in decibels per octave
(6, 12 or 18dB/Oct.) (J) LOW PASS OUTPUT RCA OR XLR (MALE)
(D) HIGH PASS LEVEL CONTROL (K) HIGH PASS OUTPUT RCA OR XLR (MALE)
Sets high pass output level for channel.
(L) MODE SELECTOR SWITCH
-5dB to + 5dB in 1dB steps.
(E) HIGH PASS SLOPE SELECTOR
Sets high pass slope in decibels per octave
(6, 12 or 18dB/Oct.)
Selectable 70 Hz, 100 Hz, 140 Hz, 200 Hz, Features Stereo 2-way
frequencies 300 Hz, 450 Hz, 700 Hz, 1 kHz, Monaural 3-way
10B standard 2 kHz, 3 kHz, 4.5 kHz Stereo 2-way summed low pass
Balanced or unbalanced
Selectable 40 Hz, 50 Hz, 60 Hz, 70 Hz,
frequencies* 80 Hz, 90 Hz, 100 Hz, 200 Hz, Independent high and low pass
10B sub 250 Hz, 300 Hz, 400 Hz, 500 Hz frequency selection
Slope 6/12/18 dB per Oct.