Text preview for : Panel_AUO_B133HAN03-0_0_[DS].pdf part of . Various Panel AUO B133HAN03-0 0 [DS] . Various LCD Panels Panel_AUO_B133HAN03-0_0_[DS].pdf
Back to : Panel_AUO_B133HAN03-0_0_[ | Home
Product Specification
AU OPTRONICS CORPORATION
( ) Preliminary Specifications
( V ) Final Specifications
Module 13.3"(13.26") FHD 16:9 Color TFT-LCD
with LED Backlight design
Model Name B133HAN03.0 (H/W:1A)
Note ( ) LED Backlight with driving circuit design
Customer Date Approved by Date
Marcus Yen 11/16/2012
Checked &
Date Prepared by Date
Approved by
Katrina Chen 11/15/2012
Note: This Specification is subject to change MPBU Marketing Division
without notice. AU Optronics corporation
B133HAN03.0 Document Version : 1.2 1 of 31
Product Specification
AU OPTRONICS CORPORATION
Contents
1. Handling Precautions .............................................................. 4
2. General Description ................................................................ 5
2.1 General Specification ..........................................................................................................................5
2.2 Optical Characteristics ........................................................................................................................6
3. Functional Block Diagram ..................................................... 11
4. Absolute Maximum Ratings................................................... 12
4.1 Absolute Ratings of TFT LCD Module.............................................................................................12
4.2 Absolute Ratings of Environment .....................................................................................................12
5. Electrical Characteristics....................................................... 13
5.1 TFT LCD Module..............................................................................................................................13
5.2 Backlight Unit ...................................................................................................................................14
6. Signal Interface Characteristic.............................................. 17
6.1 Pixel Format Image ...........................................................................................................................17
6.2 Integration Interface Requirement.....................................................................................................18
7. Panel Reliability Test ............................................................ 24
7.1 Vibration Test ....................................................................................................................................24
7.2 Shock Test .........................................................................................................................................24
7.3 Reliability Test...................................................................................................................................24
8. Mechanical Characteristics.................................................... 25
8.1 LCM Outline Dimension...................................................................................................................25
8.1.1 Standard Front View.......................................................................................................................25
9. Shipping and Package ........................................................... 27
9.1 Shipping Label Format ......................................................................................................................27
9.2 Carton Pakage....................................................................................................................................28
9.3 Shipping Package of Palletizing Sequence........................................................................................28
10. Appendix............................................................................. 29
10.1 EDID Description............................................................................................................................29
B133HAN03.0 Document Version : 1.2 2 of 31
Product Specification
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page Old description New Description Remark
0.0 2012/03/27 All First Edition
0.1 2012/04/10 28 EDID(B133HAF01.0) EDID(B133HAN03.0)
0.2 2012/04/18 5 Weight 222g Weight 219g
0.3 2012/05/11 5,6,23,24 Weight 219g Weight 215g
Luminance 340 typ / 289 min Luminance 350 typ / 300 min
CR TBD CR 800 typ / 600 min
Physical Size Z :2.515 max Physical Size Z :2.465 max
st
Color Coordinates TBD Color Coordinates 1 update
2D drawing update
0.4 2012/06/18 23 Reliability Test Reliability Test
High temperature storage 7 0 High temperature storage 6
0
Low temperature storage -3 0 Low temperature storage -2 0
0.5 2012/07/11 6 Color support Color support
16M 8bit 262K 6bit
1.0 2012/08/24 19 LED Power Supply LED Power Supply
Min 6V Min 5.5V
1.1 2012/9/21 1, 26 H/W code 0A H/W code 1A (Thinning Source IC for
COG mura)
1.2 2012/10/8 6 Temperature Range 0 to +50
Operating
12 Storage Temperature Storage Temperature
-20, +60 0, +50
23 High Temperature Operation High Temperature Operation
60 50
23 Low Temperature Operation Low Temperature Operation
-20 0
B133HAN03.0 Document Version : 1.2 3 of 31
Product Specification
AU OPTRONICS CORPORATION
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration
or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate
nor tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source (IEC60950 or UL1950), or be applied exemption.
13) Disconnecting power supply before handling LCD modules, it can prevent electric shock,
DO NOT TOUCH the electrode parts, cables, connectors and LED circuit part of TFT
module that a LED light bar build in as a light source of back light unit. It can prevent
electrostatic breakdown.
B133HAN03.0 Document Version : 1.2 4 of 31
Product Specification
AU OPTRONICS CORPORATION
2. General Description
B133HAN03.0 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel,
a driver circuit, and LED backlight system. The screen format is intended to support the 16:9
FHD, 1,920(H) x1,080(V) screen and 262k colors ( RGB 6-bits) with LED backlight driving
circuit. All input signals are eDP interface compatible.
B133HAN03.0 is designed for a display unit of notebook style personal computer and
industrial machine.
2.1 General Specification
The following items are characteristics summary on the table at 25 condition:
Items Unit Specifications
Screen Diagonal [mm] 336.71
Active Area [mm] 293.472 x 165.078
Pixels H x V 1,920x3(RGB) x 1,080
Pixel Pitch [mm] 0.15285x 0.15285
Pixel Format R.G.B. Vertical Stripe
Display Mode AHVA, Normally Black
2
White Luminance (ILED=20mA) [cd/m ] 350 typ. (5 points average)
(Note: ILED is LED current) 300 min. (5 points average)
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 700 typ/ 500 min
Response Time [ms] 25 typ / 35 Max
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 4.45W max.
(Column Inversion)
Weight [Grams] 215g max
Physical Size [mm] Min. Typ. Max.
Length 304.4 304.9 305.4
Width 190.0 190.5 191.0
Thickness - 2.315 2.465
Electrical Interface 2 lane eDP
B133HAN03.0 Document Version : 1.2 5 of 31
Product Specification
AU OPTRONICS CORPORATION
Glass Thickness [mm] 0.3
Surface Treatment Anti-Glare, Hardness 3H
Support Color 262k colors ( RGB 6-bits)
Temperature Range
o
Operating [ C] 0 to +50
o
Storage (Non-Operating) [ C] -20 to +60
RoHS Compliance RoHS Compliance
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25
(Room Temperature) :
Item Symbol Conditions Min. Typ. Max. Unit Note
White Luminance 5 points average 2
300 350 - cd/m 1, 4, 5.
ILED=20mA
R Horizontal (Right) 80 85 -
degree
L CR = 10 (Left) 80 85 -
Viewing Angle 4, 9
H Vertical (Upper) 80 85 -
L CR = 10 (Lower) 80 85 -
Luminance
5P 5 Points - - 1.25 1, 3, 4
Uniformity
Luminance
13P 13 Points - - 1.6 2, 3, 4
Uniformity
Contrast Ratio CR 500 700 - 4, 6
Cross talk % 4 4, 7
Response Time TRT Rising + Falling - 25 35 msec 4, 8
Rx 0.566 0.596 0.626
Red
Ry 0.316 0.346 0.376
Color / Gx 0.295 0.325 0.355
Green
Chromaticity Gy 0.560 0.590 0.620
Coordinates Blue Bx CIE 1931 0.123 0.153 0.183 4
By 0.096 0.126 0.156
Wx 0.283 0.313 0.343
White Wy 0.299 0.329 0.359
NTSC % - 52 -
B133HAN03.0 Document Version : 1.2 6 of 31
Product Specification
AU OPTRONICS CORPORATION
Note 1: 5 points position (Ref: Active area)
W
W /4 W /4 W /4 W /4
H /4
1 2
H /4
H 3
H /4
4 5
H /4
Note 2: 13 points position (Ref: Active area)
W
W /4 W /4 W /4 W /4
10 10
10
1 2 3
H /4
4 5
H /4
H 6 7 8
H /4
9 10
H /4 11 12 13
10
Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the
minimum test point luminance
Maximum Brightness of five points
W5 =
Minimum Brightness of five points
Maximum Brightness of thirteen points
W 13 =
Minimum Brightness of thirteen points
Note 4: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting
B133HAN03.0 Document Version : 1.2 7 of 31
Product Specification
AU OPTRONICS CORPORATION
Backlight for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen.
Photo detector
Field=2