Text preview for : Panel_AUO_B170WP04_V0_0_[DS].pdf part of . Various Panel AUO B170WP04 V0 0 [DS] . Various LCD Panels Panel_AUO_B170WP04_V0_0_[DS].pdf
Back to : Panel_AUO_B170WP04_V0_0_[ | Home
Product Specification
AU OPTRONICS CORPORATION
B170PW04 V0
( V ) Preliminary Specifications
( ) Final Specifications
Module 17.0" WXGA Color TFT-LCD
Model Name B170WP04 V0
Customer Date Approved by Date
HP
Checked &
Prepared by
Approved by
Joselyn Liu 2005/3/31 Maxine Lee 2006/3/31
Note: This Specification is subject to change MDBU Marketing Division /
without notice. AU Optronics corporation
document version 3 1/33
PDF created with FinePrint pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
B170PW04 V0
Contents
1. Handling Precautions .............................................................................................................. 4
2. General Description ................................................................................................................. 5
2.1 Display Characteristics ...................................................................................................... 5
2.2 Optical Characteristics ....................................................................................................... 6
3. Functional Block Diagram..................................................................................................... 10
4. Absolute Maximum Ratings .................................................................................................. 11
4.1 TFT LCD Module.............................................................................................................. 11
4.2 Backlight Unit ................................................................................................................... 11
4.3 Absolute Ratings of Environment ..................................................................................... 11
5. Electrical characteristics....................................................................................................... 12
5.1 TFT LCD Module.............................................................................................................. 12
5.2 Backlight Unit ................................................................................................................... 14
6. Signal Characteristic ............................................................................................................. 16
6.1 Pixel Format Image .......................................................................................................... 16
6.2 The input data format ....................................................................................................... 17
6.3 Signal Description ............................................................................................................ 19
6.4 Interface Timing................................................................................................................ 20
6.5 Power ON/OFF Sequence ............................................................................................... 22
7. Connector & Pin Assignment................................................................................................ 23
7.1 TFT LCD Module.............................................................................................................. 23
7.2 Backlight Unit ................................................................................................................... 23
7.3 Signal for Lamp connector ............................................................................................... 23
8. Vibration and Shock Test ...................................................................................................... 24
8.1 Vibration Test ................................................................................................................... 24
8.2 Shock Test Spec:.............................................................................................................. 24
9. Reliability ................................................................................................................................ 25
10. Mechanical Characteristics ................................................................................................. 26
10.1 LCM Outline Dimension ................................................................................................. 26
10.2 Screw Hole Depth and Center Position.......................................................................... 28
11. Shipping and Package......................................................................................................... 29
11.1 Shipping Label Format ................................................................................................... 29
11.2. Carton package ............................................................................................................. 29
12. Appendix: EDID description................................................................................................ 30
document version 3 2/33
PDF created with FinePrint pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
B170PW04 V0
Record of Revision
Version and Date Page Old description New Description Remark
V0 2005/11/15 Initial Version
V1 2005/11/23 27 Update Drawing
5 Update Contrast Ratio
6 Update Color Spec
V2 2006/3/10 6 Contrast Ratio: min 650 Contrast Ratio: min 550
Add Color Gamut
V3 2006/3/28 5 Physical Size: 10.3 (D) max Physical Size: 10.0 (D) max
26,27 New Drawing with dimension mark
updated
document version 3 3/33
PDF created with FinePrint pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
B170PW04 V0
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration
or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it
was taken out from the container, do not press the center of the CCFL Reflector
edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the
TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate
nor tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source(, IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
document version 3 4/33
PDF created with FinePrint pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
B170PW04 V0
2. General Description
B170PW04 V0 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD
panel, a driver circuit, and backlight system. The screen format is intended to support the
WXGA+ (1440(H) x 900(V)) screen and 262k colors (RGB 6-bits data driver). All input
signals are LVDS interface compatible. Inverter of backlight is not included.
B170PW04 V0 is designed for a display unit of notebook style personal computer and
industrial machine.
2.1 General Specification
The following items are characteristics summary on the table at 25 condition:
Items Unit Specifications
Screen Diagonal [mm] 391 (17.0W ")
Active Area [mm] 367.20(H) X 229.50(V)
Pixels H x V 1440x3(RGB) x 900
Pixel Pitch [mm] 0.255X0.255
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode Normally White
White Luminance (I CCFL=6.5mA) [cd/m2] 500 typ. (5 points average)
Note: ICCFL is lamp current 425 min. (5 points average)
(Note1)
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 700 typ
Optical Rise Time/Fall Time [msec] 8ms typ. (12ms max)
Nominal Input Voltage VDD [Volt] +3.3 typ. (+3.0 min, +3.6 max)
Power Consumption [Watt] 12.5 (without inverter)
Weight [Grams] 960 typ. (1100 max)
Physical Size [mm] 382.2(W)typx246.8(H)typx10.0 (D)max
Electrical Interface 2 channel LVDS
Surface Treatment Glare
Support Color Native 262K colors ( RGB 6-bit Data
driver)
Temperature Range
Operating [oC] 0 to +50
Storage (Non-Operating) [oC] -20 to +60
RoHS Compliance RoHS Compliance
document version 3 5/33
PDF created with FinePrint pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
B170PW04 V0
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25 (Room Temperature):
Item Unit Conditions Min. Typ. Max. Note
White Luminance [cd/m2] 5 points average 425 500 - 1, 4
ICCFL=6.5mA
Viewing Angle [degree] Horizontal (Right) 60 70 - 7
[degree] CR = 10 (Left)
60 70 -
[degree] Vertical (Upper) 50 60 -
[degree] CR = 10 (Lower)
50 60 -
Luminance Uniformity 5 Points 1.25 1,3
Luminance Uniformity 13 Points 2.0 2,3
CR: Contrast Ratio 550 700 - 4
Color Gamut [NTSC] 72%
Cross talk % 4 5
Response Time [msec] Rising - 6 9 6
[msec] Falling - 2 5
[msec] Rising + Falling 8 14
Color / Chromaticity Red x 0.623 0.653 0.683 2,7
Coordinates Red y
(CIE 1931) 0.308 0.338 0.368
Green x 0.269 0.299 0.329
Green y 0.578 0.608 0.638
Blue x 0.117 0.147 0.177
Blue y 0.042 0.072 0.102
White x 0.308 0.338 0.368
White y 0.316 0.346 0.376
document version 3 6/33
PDF created with FinePrint pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
B170PW04 V0
Note 1: 5 points position (Display area : 367.20(H) X 229.50(V))mm)
W
W /4 W /4 W /4 W /4
H /4
1 2
H /4
H 3
H /4
4 5
H /4
Note 2: 13 points position
W
W /4 W /4 W /4 W /4
10 10
10
1 2 3
H /4
4 5
H /4
H 6 7 8
H /4
9 10
H /4 11 12 13
10
Note 3: The luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by
the minimum test point luminance
Maximum Brightness of five points
W5 =
Minimum Brightness of five points
Maximum Brightness of thirteen points
W13 =
Minimum Brightness of thirteen points
document version 3 7/33
PDF created with FinePrint pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
B170PW04 V0
Note 4: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be executed after
lighting Backlight for 30 minutes in a stable, windless and dark room.
Photo detector
Field=2