Text preview for : Panel_COC_PM50H3000_0_[DS].pdf part of . Various Panel COC PM50H3000 0 [DS] . Various LCD Panels Panel_COC_PM50H3000_0_[DS].pdf
Back to : Panel_COC_PM50H3000_0_[DS | Home
Global LCD Panel Exchange Center www.panelook.com
)
zpjo|huGjvjGkpzwshGkl}pjlzGjvUSGs{kUG G G G
6,&+8$1 &2& ',63/$<
'(9,&(6 &2 /7'
%8<(5 1$0( 6833/<(5
6,*1$785( '$7( 6,*1$785( '$7(
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
5(&25' RI 5(9,6,216
)
GG GG
G G G GG GG
G G G GG GG
G G G G G
G G G G G
G G G G G
G G G G G
G G G G G
CONTENTS
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
0. WARNINGS AND CAUTIONS 4
Warning 4
Caution 5
1. GENERAL DESCRIPTION 8
Description 8
Features 8
Applications 8
Electrical Interface of Plasma Display 8
General Specifications 9
2. ELECTRICAL SPECIFICATIONS 10
Input Power Specifications 10
Power Sequence 11
LVDS Connection 12
Input Signal Timing (Non-interlaced Mode) 16
I2C Timing Specification & Register Description 18
3. ELECTRO OPTICAL SPECIFICATIONS 25
Electro Optical characteristic Specifications (60Hz) 25
Electro Optical characteristic Specifications (50HZ) 25
4. MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS 28
Mechanical Characteristic Specifications 28
Vibration and Drop Specifications 28
Environmental Conditions 28
5. IMAGE STICKING CHARACTERISTICS 29
6. OUTLINE DRAWING 30
Front View 30
Rear View 31
7. CONNECTORS AND CONNECTIONS 30
8. LABEL 34
9. PACKING 36
* APPENDIX 37
Cell Defect Specifications 37
Scratch and Dent Specification 38
Sound Pressure Level Specification 38
Film Filter Specification 38
0. Warnings and Cautions
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
WARNING indicates hazards that may lead to death or injury if ignored.
CAUTION indicates hazards that may lead to injury or damage to property if ignored.
! WARNING
1) This product uses a high voltage (450 V max.). Do not touch the circuitry of this product with your
hands when power is supplied to the product or immediately after turning off the power. Be sure to
confirm that the voltage is dropped to a sufficiently low level.
2) Do not supply a voltage higher than that specified to this product. This may damage the product and
may cause a fire.
3) Do not use this product in locations where the humidity is extremely high, where it may be splashed
with water, or where flammable materials surround it. Do not install or use the product in a location
that does not satisfy the specified environmental conditions. This may damage the product and may
cause a fire.
4) If a foreign substance (such as water, metal, or liquid) gets inside the product, immediately turn off
the power. Continuing to use the products it may cause fire or electric shock.
5) If the product emits smoke, an abnormal smell, or makes an abnormal sound, immediately turn off
the power. If nothing is displayed or if the display goes out during use, immediately turn off the
power. Continuing to use the product as it is may cause fire or electric shock.
6) Do not disconnect or connect the connector while power to the product is on. It takes some time for
the voltage to drop to a sufficiently low level after the power has been turned off. Confirm that the
voltage has dropped to a safe level before disconnecting or connecting the connector. Otherwise,
this may cause fire, electric shock, or malfunction.
7) Do not pull out or insert the power cable from/to an outlet with wet hands. It may cause electric
shock.
8) Do not damage or modify the power cable. It may cause fire or electric shock.
9) If the power cable is damaged, or if the connector is loose, do not use the product; otherwise, this
can lead to fire or electric shock.
10) If the power connector or the connector of the power cable becomes dirty or dusty, wipe it with a
dry cloth. Otherwise, this can lead to fire.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
! CAUTION
General
1) Do not place this product in a location that is subject to heavy vibration, or on an unstable surface
such as an inclined surface. The product may fall off or fall over, causing injuries.
2) When moving the product, be sure to turn off the power and disconnect all the cables. While moving
the product, watch your step. The product may be dropped or fall, leading to injuries of electric
shock.
3) Before disconnecting cable from the product, be sure to turn off the power. Be sure to hold the
connector when disconnecting cables. Pulling a cable with excessive force may cause the core of
the cable to be exposed or break the cable, and this can lead to fire or electric shock.
4) This product should be moved by two or more persons. If one person attempts to carry this product
alone, he/she may be injured.
5) This product contains glass. The glass may break, causing injuries, if shock, vibration, heat, or
distortion is applied to the product.
6) The temperature of the glass surface of the display may rise to 80 C or more depending on the
conditions of use. If you touch the glass inadvertently, you may be burned.
7) Do not poke or strike the glass surface of the display with a hard object. The glass may break or be
scratched. If the glass breaks, you may be injured.
8) If you glass surface of the display breaks or is scratched, do not touch the broken pieces or the
scratches with bare hands. You may be injured.
9) Do not place an object on the glass surface of the display. The glass may break or be scratched.
Design
1) This product may be damaged if it is subject to excessive stresses (such as excessive voltage, current,
or temperature). The absolute maximum ratings specify the limits of these stresses, and system
design must ensure that none of the absolute maximum ratings are exceeded.
2) The recommended operating conditions are conditions in which the normal operation of this product
is guaranteed. All the rated values of the electrical specifications are guaranteed within these
conditions. Always use the product within the range of the recommended operating conditions.
Otherwise, the reliability of the product may be degraded. Use of the product with a combination of
parameters, conditions, or logic not specified in the specifications of this product is not guaranteed.
If intending to use the product in such a way, be sure to consult COC in advance.
3) This product emits near infrared rays (800 to 1000nm) that may cause the remote controllers of other
electric products to malfunction. To avoid this, use an infrared absorption filter and thoroughly
evaluate the system and environment.
4) This product uses high-voltage switching and a high speed clock. A system using this product
should be designed so that it does not affect the other systems, and should be thoroughly evaluated.
5) The materials which contain sulfur are forbidden to use, because they may damage PDP module.
6) This product has a glass display surface. Design your system so that excessive shock and load are not
applied to the glass. Exercise care that the vent at the corner of the glass panel is not damaged. If
the glass panel or vent is damaged, the product is inoperable.
7) There are some exposed components on the rear panel of this product. Touching these components
may cause an electric shock.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
8) This product uses a high voltage. Design your system so that any residual voltage in this product is
dissipated quickly when power is turned off, observing the specifications.
9) This product uses heat-emitting components. Take the heat emitted by these components into
consideration when designing your system. If the product is used outside the specified temperature
range, it may malfunction.
10) This product uses a high voltage and, because of its compact design, components are densely
mounted on the circuit board. If dust collects on these components, it can cause short-circuiting
between the pins of the components and moisture can cause the insulation between the components
to break down, causing the product to malfunction.
11) Regulations and standards on safety and electromagnetic interference differ depending on the
country. Design your system in compliance with the regulations and standards of the country for
which your system is intended.
12) To obtain approval under certain safety standards (such as UL and EN), a filter that passes a shock
test must be fitted over the glass surface of the finished product. In addition, it must be confirmed
that the level of UV emissions is within the range specified by such standards.
13) If this product is used as a display board to display a static image, image sticking occurs. This
means that the luminance of areas of the display that remain lit for a long time drops compared with
the luminance of areas that are lit for a shorter time, causing uneven luminance across the display.
The degree to which this occurs is in proportion to the luminance at which the display is used. To
prevent this phenomenon, therefore, avoid static images as much as possible and design your
system so that it is used at a low luminance, by reducing signal level difference between bright area
and less bright area through signal processing.
14) Within the warranty period, general faults that occur due to defects in components such as ICs will
be rectified by COC without charge. However, IMAGE STICKING is not included in the warranty.
Repairs due to the other faults may be charged for depending on responsibility for the faults.
15) In case of AC PDP driving mechanism, because the brightness of output is not always proportional
to input signals. Therefore the non-linearity of gray can occasionally be observed in certain gray
levels as well as Contour and Error Diffusion Noise can be appeared when a dark picture is on the
screen especially. These are phenomena that can be observed on the PDP driving mechanism. With
simple adjustment to picture brightness control, these can be reduced considerably.
16) Because of the need to control the power consumption on the PDP driving mechanism, the
APL(Average Picture Level) mode was equipped. Thus, as the picture on the screen changes, there
can be slightly switched in brightness. This also is a phenomenon that can be observed on the PDP
driving mechanism.
17) This product is designed to COC s Standard quality grade. If you wish to use the product for
applications outside the scope of the Standard quality grade, be sure to consult COC in
advance to assess the technological feasibility before starting to design your system.
Use
1) Because this product uses a high voltage, connecting or disconnecting the connectors while power is
supplied to the product may cause malfunctioning. Never connect or disconnect the connectors
while the power is on. Immediately after power has been turned off, a residual voltage remains in
the product. Be sure to confirm that the voltage has dropped to a sufficiently low level.
2) Watching the display for a long time can tire the eyes. Take a break at appropriate intervals.
3) PDP s brightness and contrast ratio is lower than that of the CRT. The picture is dimmer with
surrounding light and better for viewing in dark condition.
4) Do not cover or wrap the product with a cloth or other covering while power is supplied to the
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
product.
5) Before turning on power to the product, check the wiring of the product and confirm that the supply
voltage is within the rated voltage range. If the wiring is wrong or if a voltage outside the rated
range is applied, the product may malfunction or be damaged.
6) Do not store this product in a location where temperature and humidity are high. This may cause the
product to malfunction. Because this product uses a discharge phenomenon, it may take time to
light (operation may be delayed) when the product is used after it has been stored for a long time. In
this case, it is recommended to light all cells for about 2 hours (aging).
7) If the glass surface of the display becomes dirty, wipe it with a soft cloth moistened with a neutral
detergent. Do not use acidic or alkaline liquids, or organic solvents.
8) Do not tilt or turn upside down while the module package is carried, the product may be damaged.
9) This product is made from various materials such as glass, metal, and plastic. When discarding it, be
sure to contact a professional waste disposal operator.
Repair and Maintenance
Because this product combines the display panel and driver circuits in a single module, it cannot be
repaired or maintained at user s office or plant. Arrangements for maintenance and repair will be
determined later.
Others
1) If your system requires the user to observe any particular precautions, in addition to the above
warnings and cautions, include such caution and warning statements in the manual for your system.
2) If you have any questions concerning design, such as on housing, storage, or operating environment,
consult COC in advance.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
1. GENERAL DESCRIPTION
DESCRIPTION
The PM50H3000 is a 50-inch 16:9 color plasma display module with resolution of 1365(H)
768(V) pixels.
This is the display device which offers vivid colors with adopting AC plasma technology by COC.
FEATURES
High peak brightness (500cd/m2 Typical) and high contrast ratio (10,000:1 Typical) enables user to
create high performance PDP SETs.
APPLICATIONS
- Public information display
- Video conference systems
- Education and training systems
ELECTRICAL INTERFACE OF PLASMA DISPLAY
The PM50H3000 requires only 8/10 bits of digital video signals for each RGB color. The PM50H3000
is equipped with P-CUBE function which analyzes display signals to optimize system control factor for
showing the best display performance.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
GENERAL SPECIFICATIONS
- Model Name : PM50H3000
- Number of Pixels : 1365(H) 768(V) (1pixel=3 RGB cells)
- Pixel Pitch : 810 (H) 810 (V)
- Cell Pitch : 270 (H) 810 (V)
- Display Area : 1105.6(H) 622.0 (V) 0.5mm
- Outline Dimension : 1175 H 688 V 49(D) 1mm
- Pixel Type : RGB Closed (Well) type
- Number of Gradations : 10bit (R) 1,024 (G) 1,024 (B) 1,024 colors (1.073 billion)
: 8bit (R) 256 (G) 256 (B) 256 colors (16.78 million)
- Weight : 16.6 0.5 Kg (Net 1EA)
- Aspect Ratio : 16:9
- Peak Brightness : Typical 500cd/ (1/100 White Window pattern at center)
- Contrast Ratio : Average 180:1 (In a bright room with 100Lux at center)
: Typical 10,000:1 (In a dark room 1/100 White Window pattern at center)
- Power Consumption : Max. 300W
- Expected Life-time : Warranty life time 100,000 Hours with continuous operation
Display Dot Diagram
1st Pixel 2nd Pixel 3rd Pixel
column column column UUUUUUUUUUUUUUU 1,365 th
Pixel
Cell Pitch (width) column
Pixel Pitch (width) 810
270
1st Pixel
row B R G B R G B R G
G R G R G R UUUUUUUUUUUUUUU B R G
G R
2nd Pixel
row B R G B R G B R G
G R G R G R UUUUUUUUUUUUUUU
(Height)
Pitch
3rd Pixel
row B R G B R G B R G
G R G R G R UUUUUUUUUUUUUUU
810
4th Pixel
row UUUUUUUUUUUUUUU
B R G B R G B R G
G R G R G R
UUUUUUUUUUUUUUU
UUUUUUUUUUUUUUU
768 th
Pixel
row
B R G B R G B R G
G R G R G R UUUUUUUUUUUUUUU B R G
G R
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
3D Mode Display
PM50H3000 supports four types of 3D mode display:
1. Side by Side
2, Line by Line(vertical)
3. Line by Line(Horizontal)
4. Pixel by Pixel
2. Electrical Specifications
Input power Specifications
f
f
f
f
f
f
f
*1. PDP Module Maximum Power is below 300W.
[Note]
1. Earth Leakage current
The power supply leakage current shall be less than 0.5mA
Power Saving Management [DPMS]
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Voltage 5VSTB D5V D15V VA VS
Load [A] 30mA
Wattage [W] 0.5W
Power Sequence
LVDS Connection
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Symbol Function and description
RA+ Channel-A Pos. Receiver Input
RA- Channel-A Neg. Receiver Input
RB+ Channel-B Pos. Receiver Input
RB- Channel-B Neg. Receiver Input
RC+ Channel-C Pos. Receiver Input
RC- Channel-C Neg. Receiver Input
RD+ Channel-D Pos. Receiver Input
RD- Channel-D Neg. Receiver Input
RE+ Channel-E Pos. Receiver Input
RE- Channel-E Neg. Receiver Input
RCLK+ Clock Pos. Receiver Input
RCLK- Clock Neg. Receiver Input
LVDS Signal Pin Assignment
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Part_ Number : 1001-65231 (C_NET)
Pin. No Symbol Pin. No Symbol
1 G 17 NC
2 G 18 NC
3 RA- 19 RD-
4 RA+ 20 RD+
5 G 21 G
6 G 22 NC
7 RB- 23 RE-
8 RB+ 24 RE+
9 NC 25 NLNP
10 NC 26 G
11 RC- 27 Sclk
12 RC+ 28 G
13 G 29 Sdata
14 G 30 G
15 Rclk- 31 NC
16 Rclk+
RF-/+ is 12bit DATA (not used no connect)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
FFC LVDS connector (Top view)
Pin. No Symbol Pin. No Symbol
1 NC 17 RD-
2 NC 18 RD+
3 RE- 19 G
4 RE+ 20 NC
5 RA- 21 G
6 RA- 22 3D SYNC
7 G 23 G
8 RB- 24 NC
9 RB+ 25 G
10 G 26 NC
11 RC- 27 NC
12 RC+ 28 SCLK
13 G 29 G
14 Rclk- 30 SDATA
15 Rclk+
16 G
NOTE)
1. Two LVDS connector are all located in Logic Board. Choose one connector only
2. Pin numbering order:
Right to left view from component side of Logic Board
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
LVDS Receiver 8bit
LSB ~ MSB
Symbol Signal Definition and Function
0 1 2 3 4 5 6
RA+/- Channel-A. Receiver Input RE0 RE1 RE2 RE3 RE4 RE5 GE0
RB+/- Channel-B. Receiver Input GE1 GE2 GE3 GE4 GE5 BE0 BE1
RC+/- Channel-C. Receiver Input BE2 BE3 BE4 BE5 HS VS DE
RD+/- Channel-D. Receiver Input RE6 RE7 GE6 GE7 BE6 BE7
RE+/- Channel-E. Receiver Input
RF+/- Channel-F. Receiver Input
RCLK+/- Clock. Receiver Input DCLK
LVDS Receiver 10bit
LSB ~ MSB
Symbol Signal Definition and Function
0 1 2 3 4 5 6
RA+/- Channel-A. Receiver Input RE2 RE3 RE4 RE5 RE6 RE7 GE2
RB+/- Channel-B. Receiver Input GE3 GE4 GE5 GE6 GE7 BE2 BE3
RC+/- Channel-C. Receiver Input BE4 BE5 BE6 BE7 HS VS DE
RD+/- Channel-D. Receiver Input RE8 RE9 GE8 GE9 BE8 BE9
RE+/- Channel-E. Receiver Input RE0 RE1 GE0 GE1 BE0 BE1
RF+/- Channel-F. Receiver Input
RCLK+/- Clock. Receiver Input DCLK
NOTE)
RE0~RE9 : 10 bit Red Pixel Video Signal (RE0:LSB, RE10:MSB)
GE0~GE9 : 10 bit Green Pixel Video Signal (GE0:LSB, GE10:MSB)
BE0~BE9 : 10 bit Blue Pixel Video Signal (BE0:LSB, BE10:MSB)
VS : Vertical Video Sync
HS : Horizontal Video Sync
DE : Video Data Enable
Input Signal Timing (Non-interlaced Mode)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Min & max of each signal are measured values when other signal is Typ.
Input signal 60Hz specification
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
60Hz
Parameter Symbol Min. Typ. Max. Unit Note
Period Tclk 14.3 13.5 12.8 ns
DCLK
Frequency - 71 74 77 MHz
Period Thp 1451 1504 1520 Tclk
Hsync
Width Twh 6 10 12 Tclk
Period Tvp 810 820 830 Thp
Vsync
Width Twv 2 6 10 Thp
Horizontal Valid T hv 1365 1365 1365 Tclk
Data Horizontal Back Porch T hbp 56 76 86 Tclk
Enable Vertical Valid Tvp 768 768 768 Thp
Vertical Back Porch Tvbp 20 30 35 Thp
Input signal 50Hz specification
50Hz
Parameter Symbol Min. Typ. Max. Unit Note
Period Tclk 14.3 13.5 12.8 ns
DCLK
Frequency - 71 74 77 MHz
Period Thp 1451 1504 1520 Tclk
Hsync
Width Twh 6 10 12 Tclk
Period Tvp 976 984 993 Thp
Vsync
Width Twv 2 6 10 Thp
Horizontal Valid T hv 1365 1365 1365 Tclk
Data Horizontal Back Porch T hbp 56 76 86 Tclk
Enable Vertical Valid Tvp 768 768 768 Thp
Vertical Back Porch Tvbp 20 30 35 Thp
I2C Timing Specification & Register Description
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
I2C Start, Restart and Stop condition
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Register Description
I2C data
I2C address Mode Bit
7 6 5 4 3 2 1 0
08h BRIGHT_MODE 4bit N N N N PAL(1:0) NT (1:0)
0Bh GAMMA_MODE 4bit N N N N PAL (1:0) NT (1:0)
10h COLOR_INVERSION 1bit N N N N N N N ON/OFF
18h ISM_MODE 1bit N N N N N N N ON/OFF
20h PGR 3bit N N N N N ON/OFF Sel (1:0)
C0h 3D enable switch 1bit N N N N N N N ON/OFF
C1h 3D Mode select 2bit N N N N N N
Sel(1:0)
C2h L/R eye switch 1bit N N N N N N N ON/OFF
C3h 3D to 2D Enable 1bit N N N N N N N ON/OFF
C4h,C5h Sync Output(Left) 16bit Sel(15:0)
C6h,C7h Sync Output(Right) 16bit Sel(15:0)
C8h Full Resolution Select 1bit N N N N N N N ON/OFF
C9h Dual View Enable 1bit N N N N N N N ON/OFF
Bright MODE
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
08h BRIGHT_MODE 4bit N N N N PAL (1:0) NT (1:0)
PAL(1:0) : 50Hz bright mode
NT(1:0) : 60Hz bright mode
00 : 100% brightness mode(Default Value)
01 : 80% brightness mode
10 : 60% brightness mode
11 : TBD
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Gamma MODE
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
0Bh GAMMA_MODE 4bit N N N N PAL (1:0) NT (1:0)
PAL(1:0) : 50Hz gamma mode
NT(1:0) : 60Hz gamma mode
00 : 2.2 gamma mode, Default Value
01 : 2.4 gamma mode
10 : 1 gamma mode
11 : TBD
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Color Inversion MODE
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
10h COLOR_INVERSION 1bit N N N N N N N ON/OFF
Image inversion enable
0 : Image inversion off, Default Value
1 : Image inversion on
IRR (Image Retention Reduction) MODE
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
18h IRR_MODE 1bit N N N N N N N ON/OFF
This module has been equipped with a special method that minimizes the image retention phenomenon.
When in the fixed pattern display mode decreases the brightness over a period of 5 minutes with small steps.
The figure below shows that the decrease in brightness is so small the user will not notice.
The Brightness level decreases 1 step per 3sec to Brightness min level.
1 : Image Retention Reduction on, Default Value.
0 : Image Retention Reduction off.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Internal Pattern Generation
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
20h PGR 3bit N N N N N ON/OFF SEL (1:0)
Pattern generation is automatically.
ON/OFF: 0 => OFF, 1 => ON Default Value 0
SEL(1:0): Pattern Select
01 : rotation stop
10 : color bar
00 : 16% window
11 : rotation pattern
1.F_W 2.F_R 3.F_G 4.F_B
5.Horigental 256 gray_White
6.Horigental 256 gray_Red
7.Horigental 256 gray_Green
8.Horigental 256 gray_Blue
9.Vertical 256 gray_White
10.Vertical 256 gray_Red
11.Vertical 256 gray_Green
12.Vertical 256 gray_Blue
13.Diagonal 256 gray_White
14. Diagonal 256 gray_Red
15. Diagonal 256 gray_Green
16. Diagonal 256 gray_Blue 1.Full_White
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
3D Enable Switch
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
3D enable
C0h 1bit N N N N N N N ON/OFF
switch
ON/OFF: 0 => OFF, 1 => ON Default Value 0
3D Mode select
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
C1h 3D Mode select 2bit N N N N N N SEL (1:0)
SEL(1:0): Pattern Select
00 :pixel by pixel
01 : side by side(C9=0x01,enable);column by column(C9=0x00,enable)
10 :line by line
L/R eye switch
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
C2h L/R eye switch 1bit N N N N N N N ON/OFF
0 :Disable(default value)
1 : Enable
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
3D to 2D switch
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
C3h 3D to 2D switch 1bit N N N N N N N ON/OFF
3D to 2D switch enable
0 :Disable(default value)
1 : Enable(0xC0=1)
Sync Output
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
C4h,C5h Sync Output (Left) 8bit N N N N N N N N
C6h,C7h Sync Output(Right) 8bit N N N N N N N N
Full resolution select
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
C8h Full resolution select 1bit N N N N N N N ON/OFF
Full resolution select ( no value now)
0 :Disable(default value)
1 : Enable
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Dual View Control
I2C I2C data
Mode Bit
address 7 6 5 4 3 2 1 0
Dual View Control
C9h 1bit N N N N N N N ON/OFF
Dual View Enable (side by side)
0 :Disable(default value)
1 : Enable
3. ELECTRO OPTICAL SPECIFICATIONS
Electro Optical characteristic Specifications (60Hz)
ITEM Symbol Condition 1) Min. Typ. Max. Unit
1% white window
Peak White Brightness * BWP 400 500 - cd/m2 2)
(Test mode)
Average White Brightness * BW 40 45 - cd/m2
Brightness Uniformity BU -15 0 +15 %
Color X XW Full White 0.270 0.285 0.300
White
Coordinate
Y YW 0.265 0.280 0.295
Color Coordinate Uniformity CU -0.01 0 +0.01
Bright Room CRBR 100Lx at center 140:1 180:1 -
Contrast Contrast
Ratio* Ratio*
Dark Room 3) CRDR 1% white window 8,000:1 10,000:1 -
Power Consumption 4) PW Full White - 260 290 W
Tsync Margin Hz +/-1.5 Hz
Electro Optical characteristic Specifications (50Hz)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
ITEM Symbol Condition 1) Min. Typ. Max. Unit
1% white window
Peak White Brightness * BWP 400 500 - cd/m2 2)
(Test mode)
2
Average White Brightness * BW 40 45 - cd/m
Brightness Uniformity BU -15 0 +15 %
Color X XW Full White 0.270 0.285 0.300
White
Coordinate Y YW 0.265 0.280 0.295
Color Coordinate Uniformity CU -0.01 0 +0.01
Bright Room CRBR 100Lx at center 130:1 170:1 -
Contrast Contrast
Ratio* Dark Room 3) CRDR 1% white window 8,000:1 10,000:1 - Ratio*
Power Consumption 4) PW Full White - 260 290 W
Tsync Margin Hz +/-1.5 Hz
*) Module brightness can be lowed up to 25% comparing with room temperature when panel temperature
is below than 18 .
1) All characteristics are measured in the room temperature.
2) The brightness of the white peak position is measured while the 1%-window pattern is ON state.
And then, it should be checked in 10 seconds after 1%-window is ON state.
- Occasionally, the dark position could be changed to any other point arbitrary.
3) The brightness of dark room is less than 1 lux.
4) Total Power Consumption can be up to 300W according to the displayed pattern.
4. MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS
Mechanical Characteristic Specifications
Item Spec. Unit Remark
Outline Dimensions 1175(H)*688(V)*49 1 mm See Outline Drawing
Display Area 1105.6(H)*622.0(V)* 0.5 mm
Net 16.6 0.5 Kg
Weight
Gross 230 5(12EA/1BOX) Kg
Vibration, shock and Drop Specifications
Item Condition Remark
Vibration Non operation
X,Y direction 1.04G, Z direction, 0.73G,5~100Hz
(Sweep time : 30 Min)
Shock
X,Y direction 20G, Z direction 15G, duration time
20ms
Drop Bottom : Pivot point height 15cm Packing edge Non operation
Falling height : 20.32 cm 12ea Packed state
Environmental Conditions
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
1) Operation Condition
Item Recommended Absolute maximum
Ambient
5 ~45 0 ~50
Temperature
Humidity 20~70% RH 20~80% RH
Panel surface
Absolute maximum temperature: 120 ( T 20 / )
temperature
Note : 1. this module can be operated normally at lower altitude than 2000m(625Torr)
2. In case that a module is left out at the low temperature for a long time(more than 1 hour),
It has be operated after for at least 15 minutes.
2) Storage Conditions
Item Recommended Absolute maximum
Ambient
-5 ~45 -20 ~70
Temperature
Humidity 20~80% RH 5~85% RH
633Torr~760Torr 229Torr~760Torr
Air Pressure
(0~1,500m) (0~10,000m)
5. Image Sticking Characteristics
Image Sticking
The fluorescent substance used in the plasma module loses its brightness with the lapse of lighting time. This
deterioration in brightness appears to be a difference in brightness in relation to the surroundings, and comes to be
recognized as image sticking. In other words, the image sticking is defined as follows: when the same pattern (of the
fixed display) is displayed for a long time, a difference in brightness is caused around the lighting area and
non-lighting area due to deterioration in the fluorescent substance. When the present pattern is changed over to
another one, the boundary comes to be seen between the lighting area and non-lighting area due to difference in
brightness in the pattern shown shortly before changeover. If this condition is accumulated, the boundary or image
sticking comes to be seen with the naked eyes.
Warranty
Image sticking and faults in brightness and picture elements are excluded from the warranty objects.
Proposed measures taken to relieve image sticking
So long as there is the reduction of brightness in the fluorescent substance, it is impossible to avoid the
occurrence of image sticking. Therefore, to relieve image sticking, we offer you a method of entering an image input
that may ensure reluctance to the generation of the difference in brightness reduction among the displayed dots.
The images from TV broadcasting involve a high rate of motion picture displays. Therefore, there is less
chance of being a cause of difference in brightness reduction among the cells. Even when the fixed patterns are
displayed, they generally last for a few minutes. Since the same pattern is less liable to be displayed, there is almost no
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
influence toward image sticking. If the fixed patterns tend to be displayed for a long time, however, there occurs a
substantial imbalance between the lighting and non-lighting areas, thus causing a difference in brightness as a result.
In this document, we offer you some proposals of installation, paying attentions to the two points: the
reduction of difference in brightness achieved by integrated lighting time leveling and the method of edge smearing to
make image sticking hard to be discerned. The result from these proposals can, however, greatly depend on the
contents of images and the operating environment. Therefore, we consider that it is essential to take the suitable
measures in consideration of the customer s operating environment.
Example of Proposal 1: The display position is moved while the fixed display pattern is changed over, or it is
scrolled during the display.
Example of Proposal 2: If possible, a pattern of complementary color is incorporated (for integrated time
leveling).
Example of Proposal 3: The fixed pattern and the motion picture display are reciprocally exchanged, in order
to minimize display period of the fixed pattern.
Example of Proposal 4: During operation, the brightness of screen is suppressed as low as possible.
For the display patterns, characters are indicated not on the black ground (non-picture area) but on the
colored ground (mixture of R, G, B recommended).
6. OUTLINE DRAWING
Front View
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Rear View
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
7. Connector and Connections
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
Note : ACD output circuit
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)
8. LABEL
LABEL Sticking Position: Product Label
MODEL: PM50H3000
XXXXXXXXXX XXXXX.XXXXX
Voltage Setting
5.2V /15.5V/Va:56/Vs:213 Rating
N.A/-195/148/N.A/90 Total Max Watt: 300W
Max Volt( ): 5.2V/15.5V/Va:57V/Vs:215V