Text preview for : CP650%20Input_Output%20Wiring%20Diagram.pdf part of . Various CP650%20Input Output%20Wiring%20Diagram . Various SM scena CP650 CP650%20Input_Output%20Wiring%20Diagram.pdf
Back to : CP650%20Input_Output%20Wi | Home
CP650 Installation Manual Installation
Projector 1 Cat. No. 701
Digital Reader
2-Projector Changeover Single Projector
15 V phantom power switchable via front
Projector 1 setup control panel dip switch number 3.
Projector Changeover Relays, 5 1
OR PA Microphone 1 red
Pulsed Contacts 2 3 black
9 6 (Or Mic-multiplexer
Inboard Digital Open for setup)
1
Basement Reader Closed
Jumper Plug
50 ms (shipped installed on unit)
minimum
Cable Part Numbers: Projector 2
Projector 2 83141 (30 feet) (9.1 meters)
83237 (50 feet) (16.2 meters)
All shields must be connected Cat. No. 794
to the metal shield of the D-connector. AES/EBU Board Jumpers
OR 2 1 Digital Output Source
MADE IN U.S.A/U.K.
15
Projector Changeover Relay black
Maintained Closed Contact
J4
red 2 3
Selects Projector 2 1
AES/EBU
S/PDIF
13 1
2 1 S/PDIF
For Dolby Digital Installations
25 Digital Output Source
+15V 100 mA MAX
Proj 1 Motor Start Relay
MADE IN U.S.A/U.K.
SHIELD
GROUND
J4
MUTE Projector Motor OR
U2 AES/EBU
To Automation NONSYNC
S/PDIF
(See Interface Requirements U1
11 5 1
in Appendix B)
10 Proj 2 Motor Start Relay
05 9 6
04 Reverse Scan / LED
01 Projector Motor For future Analog Reader Board
Automation use
1
1 2 3
J1
red
UL
AUTOMATION
O CP650 SERIAL DATA (RS-232) MIC. INPUT black
J2
1 OUT 1 +
1 2 3 4 5 6
C US Digital Cinema Processor OUT 1 -
OUT 2 +
LISTED San Francisco U.S. Wootton Bassett U.K. red
PROFESSIONAL AUDIO
EQUIPMENT 4J06 MUTE
ETHERNET OUT 2 -
13 1
U2
NONSYNC READER 1 black
U1
11
01
04 MOTOR START The physical board mounting in the projector and
05
10
REMOTES AND AUD. FADER 5 43 2 1 the connector orientation affect which channel
Dolby Digital appears on which pin of the connector. Be aware
READER 2 MS1 OPTION CARD I/O that pin allocations for the channels will vary
P1
P1/ P2 depending on mounting arrangements of the
+ NONSYNC IN 1 P2 9 8 7 6
board and connector. The J2 connector pin
REMOTE DATA MS2
- +
L
L+ WARNING solder hole with a square outline is pin 1.
FADER
IN
C
C+ L R Risk of electric shock.
N/C R Do not open.
R+
H/I OUTPUT Ls NONSYNC IN 2 No user serviceable parts OPTICAL IN 1 Projector 1
Ls + inside. Refer all service Solar Cell
Rs
Rs +
to qualified personnel.
OR:
~
SW L R This equipment must be
R
100 - 240 Vac 50 - 60 Hz 120 W
1 13
SW + earthed/grounded.
R L Projector 2
R L
CAUTION This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
14 17 20 23 24 25 6-CH AUDIO INPUT
To reduce the risk of fire
MAIN AUDIO OUTPUT (External Digital Processor) OPTICAL IN 2 red
replace only with same device may not cause harmful interference, and (2) this
green
type and rating device must accept any interference received, including
interference that may cause undesired operation.
black
250V time-lag fuse.
FUSE T 6.3A L
black
This Class A digital apparatus complies with Canadian ICES003.
5 mm x 20 mm red
red
FB425A02.CDR
black
1 2 3 4 5 6
Auditorium Fader 5 4 3 2 1
L
(100K Linear Pot)
Cat. No 771
Terminals Front View
Remote Fader of Pot 9 8 7 6
Cat. No 771
Cat. No. 779
DATA
Terminals CD, Tape, etc.
GND
7.0 V Remote Control Unit
V
DATA Cat. No. 779 Non-Sync 2
GND V
V DATA 13 1
7.0
DATA GND Non-Sync 1
GND
25
Notes: SHIELD
L
1. 4. 6-Channel Analog Input
Follow all local electrical and building codes. For three conductor with shield wiring, use Belden 8771 Rs
(all unlabeled pins are signal ground)
Ls
2. Use grounded (earthed) conduit wherever possible. Avoid 3-conductor shielded cable or equivalent: tinned copper, R (normal operating level = 300 mV)
routing signal wiring near electric motors, rectifiers, power twisted pair, 22 AWG stranded tinned copper drain wire, C
SW
wiring, dimmer wiring, or other sources of electrical noise. aluminum-polyester shield, 100% shield coverage,
conductor-to-conductor 75 pF per meter.
3. For two conductor with shield wiring, use Belden 8451
2-conductor shielded cable or equivalent: tinned copper, 5. All shields must be connected to the CHASSIS of the CP650.
twisted pair, 22 AWG stranded tinned copper drain wire, This achieves the required RF interference immunity. A metal
aluminum-polyester shield, 100% shield coverage, housing must be used for all D-connectors and the shields
conductor-to-conductor 111 pF per meter. must be connected to the housing. Chassis ground and circuit
(audio) ground are internally connected. CP650 INSTALLATION WIRING
INPUT AND CONTROL CONNECTIONS
2-12
CP650 Installation Manual Installation
C UL US
AUTOMATION
O CP650
Digital Cinema Processor
SERIAL DATA (RS-232) MIC. INPUT
LISTED San Francisco U.S. Wootton Bassett U.K.
PROFESSIONAL AUDIO
EQUIPMENT 4J06 MUTE
ETHERNET
U2 13 1
NONSYNC READER 1
U1
11
01
04 MOTOR START
10 05
REMOTES AND AUD. FADER
Dolby Digital
READER 2 MS1 OPTION CARD I/O
P1
P1/ P2
+ NONSYNC IN 1 P2
Hearing black REMOTE DATA
L
MS2
L+ WARNING
Impaired FADER
IN
C
C+ L R Risk of electric shock.
System red N/C R
R+
Do not open.
L+C+R H/I OUTPUT Ls
Ls +
Rs
NONSYNC IN 2 No user serviceable parts
inside. Refer all service
to qualified personnel.
OPTICAL IN 1
Rs +
This equipment must be
~
100 - 240 Vac 50 - 60 Hz 120 W
SW
SW +
L R earthed/grounded.
R L
1 13
R L
CAUTION This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
14 17 20 23 24 25 6-CH AUDIO INPUT
To reduce the risk of fire
replace only with same device may not cause harmful interference, and (2) this