Text preview for : SONY SDM-N50.pdf part of Sony SDM-N50 Model : SDM-N50 Chassis: ST5 Chassis No. SCC-L32A-A
TFT LCD COLOR COMPUTER DISPLAY Service Manual
Back to : SONY SDM-N50.part1.rar | Home
SDM-N50
SERVICE MANUAL
US Model Canadian Model AEP Model
Chassis No. SCC-L32A-A
ST5 CHASSIS
SPECIFICATIONS
LCD panel Panel type: a-Si TFT Active Matrix Picture size: 15 inch (38 cm) Input signal format RGB operating frequency* Horizontal: 30 61 kHz Vertical: 50 85 Hz Resolution Horizontal: Max.1024 dots Vertical: Max.768 lines Input signal levels RGB video signal 0.700 Vp-p, 75 , positive SYNC signal TTL level, 2 k, positive or negative (Separate horizontal and vertical, or composite sync) 0.3 Vp-p, 75, negative (Sync on green) Audio output 2W × 2 Headphones jack Stereo minijack Accepts impedance of 16 48 AUDIO IN jack Stereo minijack Accepts impedance of 16 k Accepts level 0.5 Vrms Power requirements 100 240 V, 50 60 Hz, 0.55 0.3 A Power consumption Max. 35 W Operating temperature 5 35 °C Dimensions (width/height/depth) Display (upright): Approx. 356 × 347 × 185 mm (14 1/8 × 13 3/4 × 7 3/8 inches) Media engine (without stand): Approx. 45 × 180 × 180 mm (1 13/16 × 7 1/8 × 7 1/8 inches) Media engine (with stand): Approx. 94 × 185 × 180 mm (3 3/4 × 7 3/8 × 7 1/8 inches)
Mass Display: Approx. 2.7 kg (5 lb 15 oz) Media engine (with stand): Approx. 0.85 kg (1 lb 14 oz) DDC1/DDC2B/DDC2Bi LCD display Media engine Media engine stand Power cord System connecting cable (2 m) (applicable cable type: DP-2) HD15 (RGB) video signal cable Audio cord (stereo miniplug) Macintosh adapter Windows Monitor Information Disk/ Utility Disk Macintosh Utility Disk Warranty card Notes for Macintosh users This instruction manual Plug & Play Accessories · · · · · · · · · · · · ·
Recommended horizontal and vertical timing condition · Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 µs, whichever is larger. · Horizontal blanking width should be more than 2.3 µsec. · Vertical blanking width should be more than 450 µsec. Design and specifications are subject to change without notice.
TFT LCD COLOR COMPUTER DISPLAY
MICROFILM
SDM-N50
DIAGNOSIS
Factorical preservation register Display part trouble Backlight trouble Body temperature trouble 5V voltage anomalous 3.3V voltage anomalous SHUTDOWN_LOG1 bit4 (16) SHUTDOWN_LOG1 bit2 (4) SHUTDOWN_LOG1 bit3 (8) SHUTDOWN_LOG1 bit5 (32) SHUTDOWN_LOG1 bit6 (64) LED Part of the body only Parts of the body and the display Parts of the body and the display Parts of the body and the display Parts of the body and the display LED indicates Red (0.5 sec) and Off (0.5 sec) Amber (0.5 sec) and Off (1.5 sec) Amber (1.0 sec) and Off (1.0 sec) Amber (1.5 sec) and Off (0.5 sec) Amber (1.5 sec) and Off (0.5 sec)
*Aging mode ........................................... No input signal and press CONT key for longer than 2 second.
Power saving function (user sensor/power saving mode)
This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically enter the power saving mode. It automatically enters the low power consumption mode when the user sensor detects the absence of a user. Power consumption state normal operation 1 low power consumption mode 2 power saving mode 1 (power): off AC power: off Power consumption 35 W 4W 3W 3W 0W AC power indicator green green orange red off 1 (power) indicator green green and orange alternate orange off off
TIMING SPECIFICATION
PRIMARY MODE MODE AT PRODUCTION RESOLUTION CLOCK -- HORIZONTAL -- H-FREQ 31.469 kHz usec H. TOTAL H. BLK H. FP H. SYNC H. BP H. ACTIV -- VERTICAL -- V. FREQ(Hz) 59.940 Hz lines V. TOTAL V. BLK V. FP V. SYNC V. BP V. ACTIV -- SYNC -- INT(G) EXT(H/V)/POLARITY EXT(CS)/POLARITY INT/NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/P NO NON INT NO YES N/P NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT 525 45 10 2 33 480 66.667 Hz lines 525 45 3 3 39 480 75.000 Hz lines 500 20 1 3 16 480 85.008 Hz lines 509 29 1 3 25 480 70.156 Hz lines 449 49 12 3 34 400 85.039 Hz lines 446 46 1 3 42 400 75.066 Hz lines 502 22 2 3 17 480 59.901 Hz lines 587 107 12 2 93 480 31.778 6.356 0.636 3.813 1.907 25.422 35.000 kHz usec 28.571 7.407 2.116 2.116 3.175 21.164 37.500 kHz usec 26.667 6.349 0.508 2.032 3.810 20.317 43.269 kHz usec 23.111 5.333 1.556 1.556 2.222 17.778 31.500 kHz usec 31.746 6.349 0.635 3.810 1.905 25.397 37.927 kHz usec 26.366 6.085 1.014 2.028 3.042 20.282 37.683 kHz usec 26.537 6.297 0.450 2.024 3.823 20.240 35.162 kHz usec 28.440 5.586 1.079 1.270 3.238 22.854 MODE 0 640 X 480 25.175 MHz MODE 1 640 X 480 30.240 MHz MODE 2 640 X 480 31.500 MHz MODE 3 640 X 480 36.000 MHz MODE 4 720 X 400 28.350 MHz MODE 5 720 X 400 35.500 MHz MODE 6 720 X 480 35.573 MHz MODE 7 720 X 480 31.505 MHz
2
SDM-N50
PRIMARY MODE MODE AT PRODUCTION RESOLUTION CLOCK -- HORIZONTAL -- H-FREQ 35.156 kHz usec H. TOTAL H. BLK H. FP H. SYNC H. BP H. ACTIV -- VERTICAL -- V. FREQ(Hz) 56.250 Hz lines V. TOTAL V. BLK V. FP V. SYNC V. BP V. ACTIV -- SYNC -- INT(G) EXT(H/V)/POLARITY EXT(CS)/POLARITY INT/NON INT NO YES N/N NO NON INT NO YES P/P NO NON INT NO NO P/P NO NON INT NO YES P/P NO NON INT -- -- -- -- -- -- -- -- NO YES N/N NO NON INT NO YES N/N NO NON INT 625 25 1 2 22 600 60.317 Hz lines 628 28 1 4 23 600 75.000 Hz lines 625 25 1 3 21 600 85.061 Hz lines 631 31 1 3 27 600 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 74.553 Hz lines 667 43 3 3 37 624 60.004 Hz lines 806 38 3 6 29 768 28.444 6.222 0.667 0.889 4.667 22.222 37.879 kHz usec 26.400 6.400 1.000 3.200 2.200 20.000 46.875 kHz usec 21.333 5.172 0.323 1.616 3.232 16.162 53.674 kHz usec 18.631 4.409 0.569 1.138 2.702 14.222 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 46.727 kHz usec 20.110 5.586 0.559 1.117 3.910 14.524 48.363 kHz usec 20.677 4.923 0.369 2.092 2.462 15.754 MODE 8 800 X 600 36.000 MHz MODE 9 800 X 600 40.000 MHz MODE 10 800 X 600 49.500 MHz MODE 11 800 X 600 56.250 MHz MODE 12 -- -- MODE 13 -- -- MODE 14 832 X 624 57.285 MHz MODE 15 1024 X 768 65.000 MHz
PRIMARY MODE MODE AT PRODUCTION RESOLUTION CLOCK -- HORIZONTAL -- H-FREQ 56.476 kHz usec H. TOTAL H. BLK H. FP H. SYNC H. BP H. ACTIV -- VERTICAL -- V. FREQ(Hz) 70.069 Hz lines V. TOTAL V. BLK V. FP V. SYNC V. BP V. ACTIV -- SYNC -- INT(G) EXT(H/V)/POLARITY EXT(CS)/POLARITY INT/NON INT NO YES N/N NO NON INT NO YES P/P NO NON INT -- -- -- -- NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT 806 38 3 6 29 768 75.029 Hz lines 800 32 1 3 28 768 -- -- -- -- -- -- -- -- 74.927 Hz lines 804 36 3 3 30 768 72.188 Hz lines 666 66 37 6 23 600 66.110 Hz lines 816 48 8 4 36 768 74.927 Hz lines 804 36 3 3 30 768 59.932 Hz lines 589 109 11 3 95 480 17.707 4.053 0.320 1.813 1.920 13.653 60.023 kHz usec 16.660 3.657 0.203 1.219 2.235 13.003 -- -- -- -- -- -- -- -- 60.241 kHz usec 16.600 3.800 0.400 1.200 2.200 12.800 48.077 kHz usec 20.800 4.800 1.120 2.400 1.280 16.000 53.946 kHz usec 18.537 4.243 0.223 2.457 1.563 14.294 60.241 kHz usec 16.600 3.800 0.400 2.200 1.200 12.800 35.300 kHz usec 28.328 6.208 1.409 3.130 1.669 22.120 MODE 16 1024 X 768 75.000 MHz MODE 17 1024 X 768 78.750 MHz MODE 18 -- -- MODE 19 1024 X 768 80.000 MHz MODE 20 800 X 600 50.000 MHz MODE 21 1024 X 768 71.640 MHz MODE 22 1024 X 768 80.000 MHz MODE 23 848 X 480 38.336 MHz
3
SDM-N50
PRIMARY MODE MODE AT PRODUCTION RESOLUTION CLOCK -- HORIZONTAL -- H-FREQ 31.475 kHz usec H. TOTAL H. BLK H. FP H. SYNC H. BP H. ACTIV -- VERTICAL -- V. FREQ(Hz) 70.100 Hz lines V. TOTAL V. BLK V. FP V. SYNC V. BP V. ACTIV -- SYNC -- INT(G) EXT(H/V)/POLARITY EXT(CS)/POLARITY INT/NON INT NO YES N/N NO NON INT NO YES P/N NO NON INT NO YES N/P NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT 449 49 11 2 36 400 85.080 Hz lines 445 95 32 3 60 350 85.080 Hz lines 445 45 1 3 41 400 72.809 Hz lines 520 40 9 3 28 480 59.797 Hz lines 804 36 3 4 29 768 59.996 Hz lines 508 108 37 2 69 400 50.026 Hz lines 629 229 102 2 125 400 56.160 Hz lines 626 26 2 1 23 600 31.771 6.354 0.953 2.542 2.859 25.417 37.861 kHz usec 26.413 6.095 1.016 2.032 3.048 20.317 37.861 kHz usec 26.413 6.095 1.016 2.032 3.048 20.317 37.861 kHz usec 26.413 6.095 0.762 1.270 4.063 20.317 48.077 kHz usec 20.800 5.046 0.462 1.477 3.108 15.754 30.478 kHz usec 32.811 7.077 0.322 3.860 2.895 25.734 31.467 kHz usec 31.780 6.356 0.636 3.814 1.907 25.424 35.156 kHz usec 28.444 6.222 0.167 5.111 0.944 22.222 MODE 24 640 X 400 25.180 MHz MODE 25 640 X 350 31.500 MHz MODE 26 640 X 400 31.500 MHz MODE 27 640 X 480 31.500 MHz MODE 28 1024 X 768 65.000 MHz MODE 29 640 X 400 24.870 MHz MODE 30 720 X 400 28.320 MHz MODE 31 800 X 600 36.000 MHz
PRIMARY MODE MODE AT PRODUCTION RESOLUTION CLOCK -- HORIZONTAL -- H-FREQ 48.828 kHz usec H. TOTAL H. BLK H. FP H. SYNC H. BP H. ACTIV -- VERTICAL -- V. FREQ(Hz) 66.888 Hz lines V. TOTAL V. BLK V. FP V. SYNC V. BP V. ACTIV -- SYNC -- INT(G) EXT(H/V)/POLARITY EXT(CS)/POLARITY INT/NON INT YES YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT NO YES N/N NO NON INT 2000.1.11 VER. 730 130 48 6 76 600 59.561 Hz lines 819 51 12 6 33 768 60.078 Hz lines 805 37 3 3 31 768 59.637 Hz lines 813 45 39 3 3 768 59.608 Hz lines 628 28 5 1 22 600 20.480 4.480 0.960 1.600 1.920 16.000 48.780 kHz usec 20.500 4.500 1.000 1.500 2.000 16.000 48.363 kHz usec 20.677 4.923 0.615 3.200 1.108 15.754 48.485 kHz usec 20.625 4.625 1.219 1.219 2.188 16.000 37.434 kHz usec 26.714 6.476 1.012 2.530 2.934 20.238 MODE 32 800 X 600 50.000 MHz MODE 33 1024 X 768 64.000 MHz MODE 34 1024 X 768 65.000 MHz MODE 35 1024 X 768 64.000 MHz MODE 36 800 X 600 39.530 MHz
4
SAFETY CHECK-OUT
SDM-N50
After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators. 4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 7. Check the B+ and HV to see if they are specified values. Make sure your instruments are accurate; be suspicious of your HV meter if sets always have low HV. 8. Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC Leakage. Check leakage as described below.
To Exposed Metal Parts on Set
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOMs that are suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) WARNING!! NEVER TURN ON THE POWER IN A CONDITION IN WHICH THE DEGAUSS COIL HAS BEEN REMOVED. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY SHADING AND MARK ¡ ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL FOR SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED. AVERTISSEMENT!! NE JAMAIS METTRE SOUS TENSION QUAND LA BOBINE DE DEMAGNETISATION EST ENLEVÉE. ATTENTION AUX COMPOSANTS RELATIFS À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET UNE MARQUE ¡ SONT CRITIQUES POUR LA SÉCURITÉ. NE LES REMPLACER QUE PAR UNE PIÈCE PORTANT LE NUMÉRO SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONT L'IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT SONT IDENTIFIÉS DANS LE PRÉSENT MANUEL. SUIVRE CES PROCÉDURES LORS DE CHAQUE REMPLACEMENT DE COMPOSANTS CRITIQUES, OU LORSQU'UN MAUVAIS FONCTIONNEMENT EST SUSPECTÉ.
0.15 µF
1.5 k
AC Voltmeter (0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
5
SDM-N50
TABLE OF CONTENTS
Section Title Page
1. GENERAL .................................................................. 1-1 2. DISASSEMBLY
2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. U Board Removal ................................................ 2-1 Base Assembly Removal ...................................... 2-1 B Board Removal ................................................ 2-2 H Board Removal ................................................. 2-3 LCD Module (TFT) Removal .............................. 2-3 A Board Removal ................................................. 2-4 G Board Removal ................................................. 2-4
3. ADJUSTMENTS ...................................................... 3-1 4. DIAGRAMS
4-1. 4-2. 4-3. (1) (2) (3) (4) (5) 4-4. Block Diagrams .................................................... 4-1 Circuit Boards Location ...................................... 4-7 Schematic Diagrams and Printed Wiring Boards ... 4-8 Schematic Diagrams of A (P1-P3) Board ............ 4-9 Schematic Diagrams of B (P1-P3) Board ............ 4-23 Schematic Diagrams of H Board .......................... 4-31 Schematic Diagrams of U Board .......................... 4-35 Schematic Diagrams of G (P1-P2) Board ............ 4-43 Semiconductors ................................................... 4-47
5. EXPLODED VIEWS
5-1. 5-2. 5-3. Display ................................................................. 5-1 Chassis ................................................................. 5-2 Packing Materials ................................................ 5-3
6. ELECTRICAL PARTS LIST ............................ 6-1
6
SECTION 1 GENERAL
Precautions
Warning on power connections
· Use the supplied power cord. If you use a different power cord, be sure that it is compatible with your local power supply. For the customers in the U.S.A. If you do not use the appropriate cord, this monitor will not conform to mandatory FCC standards. For the customers in the UK If you use the monitor in the UK, please use the appropriate UK power cord.
Example of plug types
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remein as in the manual.
Maintenance
· Be sure to unplug the power cord from the power outlet before cleaning your monitor. · Clean the LCD screen with a soft cloth. If you use a glass cleaning liquid, do not use any type of cleaner containing an anti-static solution or similar additive as this may scratch the LCD screen's coating. · Clean the cabinet, panel, and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. · Do not rub, touch, or tap the surface of the screen with sharp or abrasive items such as a ballpoint pen or screwdriver. This type of contact may result in a scratched picture tube. · Note that material deterioration or LCD screen coating degradation may occur if the monitor is exposed to volatile solvents such as insecticide, or if prolonged contact is maintained with rubber or vinyl materials.
To adjust the tilt and height
This display can be adjusted within the angles shown below.
To use the display comfortably
This display is designed so that you can set it up at a comfortable viewing angle. Adjust the viewing angle of your display according to the height of the desk and chair, and so that light is not reflected from the screen to your eyes.
90°
To enjoy clear sound from the builtin stereo speaker
This monitor has a built-in stereo speaker in base of the display stand. We recommend that you position the LCD panel slightly away from the display stand. High tones from the speaker may be muffled if the LCD panel is positioned immediately on top of the stand. Be careful not to drop any metal object into the speaker's vents as the speakers generate a magnetic field. Also, this magnetic field may affect data stored on magnetic tapes and discs. Be sure to keep magnetic recording equipment, tapes, and floppy discs away from the speaker's opening. A duct is provided on the rear part of the display stand to boost the bass. Be sure not to block the duct with paper or other objects to ensure clear sound.
40°
50°
50°
for 100 to 120 V AC
for 200 to 240 V AC
for 240 V AC only
Transportation
The equipment should be installed near an easily accessible outlet. · Disconnect all cables from the monitor when transporting. When you transport this display, grasp the support and base sections of the display stand firmly with both hands. Also use both hands when carrying the media engine. If you drop the monitor, you may be injured or the monitor may be damaged. · When you transport this monitor for repair or shipment, use the original carton and packing materials.
To adjust the angles, grasp the lower sides of the LCD panel with both hands as shown below. Tilt the LCD panel adequately backward, then lift the LCD panel upward to the desired screen height, then adjust the screen tilt as desired. When adjusting the screen height and tilt, proceed slowly and carefully, being sure not to hit the LCD panel against the desk or the base of the display stand.
Installation
Do not install or leave the monitor: · In places subject to extreme temperatures, for example near a radiator, heating vent, or in direct sunlight. Subjecting the monitor to extreme temperatures, such as in an automobile parked in direct sunlight or near a heating vent, could cause deformations of the casing or malfunctions. · In places subject to mechanical vibration or shock. · Near any equipment that generates a strong magnetic field, such as a TV or various other household appliances. · In places subject to inordinate amounts of dust, dirt, or sand, for example near an open window or an outdoor exit. If setting up temporarily in an outdoor environment, be sure to take adequate precautions against airborne dust and dirt. Otherwise irreparable malfunctions could occur.
1-1
US
Replacement of the fluorescent tube
A specially designed fluorescent tube is installed as the lighting apparatus for this monitor. If the screen becomes dark, unstable, or does not turn on, replace the fluorescent tube with a new one. Consult your Sony dealer when replacing the fluorescent tube.
Disposal of the monitor
· Do not dispose of this monitor with general household waste. · The fluorescent tube used in this monitor contains mercury. Disposal of this monitor must be carried out in accordance to the regulations of your local sanitation authority.
Ducts
m
Keep the LCD panel slightly away from the base. Speaker
Handling the LCD screen
· Do not leave the LCD screen facing the sun as it can damage the LCD screen. Take care when you place the monitor by a window. · Do not push on or scratch the LCD screen. Do not place a heavy object on the LCD screen. This may cause the screen to lose uniformity or cause LCD panel malfunctions. · If the monitor is used in a cold place, a residual image may appear on the screen. This is not a malfunction. The screen returns to normal as the temperature rises to a normal operating level. · If a still picture is displayed for a long time, a residual image may appear for a while. The residual image will eventually disappear. · The LCD panel becomes warm during operation. This is not a malfunction.
4
5
Identifying parts and controls
See the pages in parentheses for further details.
LCD display
6 2 (volume) +/ and M(+)/m() buttons (pages 10, 12) These buttons display the VOLUME menu and function as the M(+)/m() buttons when selecting the menu items and making adjustments. 7 INPUT and OK button, and indicator (pages 10, 12) This button selects the INPUT 1 or INPUT 2 (HD15 (RGB) connectors) video input signal. The input signal and corresponding input indicator change each time you press this button. This button also functions as the OK button when displaying the menu on the screen.
Media engine
qg HD15 (RGB) input 2 connector (INPUT2) (page 8) This connector inputs RGB video signals (0.700 Vp-p, positive) and SYNC signals. The pin assignment is the same as qf. qh AC IN connector (page 9) This connector provides AC power to the monitor. qj AC power switch (page 9) This switch turns the monitor on and off. When the AC power switch is turned on, the display automatically turns on. qk AC power indicator (page 17) This indicator lights up in green when the media engine is turned on. The indicator lights up in red when the display is turned off with the media engine on. The indicator lights up in orange when the monitor is in the power saving mode. ql Media engine stand This stand is used to install the media engine vertically.
SYSTEM CONNECTER (TO DISPLAY)
INPUT 1
AUDIO IN
INPUT 2
MENU
8 Stereo speaker (page 10) This outputs the audio signals as sound. 9 Ducts These are used to boost the bass sound from the speaker.
INPUT 1 2 OK
0 SYSTEM CONNECTOR (page 8) This connector inputs signals from the media engine when the display and the media engine are connected with a system connecting cable. qa Headphones jack (page 10) This jack outputs audio signals to the headphones.
qs AUDIO IN jack (page 10) This jack inputs audio signals when connecting to the audio output jack of the computer or other audio equipment. qd SYSTEM CONNECTOR (TO DISPLAY) (page 8) This connector outputs signals to the display when the display and the media engine are connected with a system connecting cable. qf HD15 (RGB) input 1 connector (INPUT1) (page 8) This connector inputs RGB video signals (0.700 Vp-p, positive) and SYNC signals.
Caution Be sure to install the media engine vertically shown as left. Installing the media engine lying flat may block ventilation, and may cause a malfunction.
US
Front
Rear
SYSTEM CONNECTER
5 4 3 2 1 10 9 8 7 6 15 14 13 12 11
1-2
1 1 (Power) switch and indicator (pages 9, 17, 22) This switch turns the display on and off. The indicator lights up in green when the monitor is turned on. The indicator flashes in green and orange when the monitor is in low power consumption mode, and lights up in orange when the monitor is in power saving mode. 2 Light sensor and user sensor (pages 16, 17, 18) These sensors measure the brightness of the surrounding area and detect when a user becomes present in front of the screen. Be sure not to cover the sensor with papers, etc. 3 MENU button (page 12) This button displays the main menu. 4 6 (contrast) button (page 12) This button displays the CONTRAST menu. 5 8 (brightness) button (page 12) This button displays the BRITGHTNESS menu. Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Signal Red Blue Ground V. Sync
Green (Sync on Green) ID (Ground) DDC Ground* Red Ground Green Ground Blue Ground DDC + 5V* ID (Ground) Bi-Directional Data (SDA)* H. Sync Data Clock (SCL)*
* DDC (Display Data Channel) is a standard of VESA.
6
7
Setup
Before using your monitor, check that the following accessories are included in your carton: · LCD display · Media engine · Media engine stand · Power cord · System connecting cable (2 m) (applicable cable type: DP-2) · HD15 (RGB) video signal cable · Audio cord (stereo miniplug) · Macintosh adapter · Windows Monitor Information Disk/Utility Disk · Macintosh Utility Disk · Warranty card · Notes for Macintosh users · This instruction manual
x Connecting to a Macintosh or compatible computer
Use the supplied Macintosh adapter.
Step 3: Connect the power cord
With the media engine, display, and computer switched off, first connect the power cord to the media engine, then connect it to a power outlet.
If no picture appears on your screen
· Check that the monitor is correctly connected to the computer. · Check that the media engine is on. · If NO INPUT SIGNAL appears on the screen, try changing the input signal (page 10), and confirm that your computer's graphic board is completely seated in the correct bus slot. · If OUT OF SCAN RANGE appears on the screen, reconnect the old monitor. Then adjust the computer's graphic board so that the horizontal frequency is between 30 61 kHz, and the vertical frequency is between 50 85 Hz (only XGA mode at 75 Hz). For more information about the on-screen messages, see "Trouble symptoms and remedies" on page 20.
For customers using Windows 95/98 To maximize the potential of your monitor, install the new model information file from the supplied Windows Monitor Information Disk onto your PC. This monitor complies with the "VESA DDC" Plug & Play standard. If your PC/graphics board complies with DDC, select "Plug & Play Monitor (VESA DDC)" or this monitor's model name as the monitor type in the "Control Panel" of Windows 95/98. If your PC/graphics board has difficulty communicating with this monitor, load the Windows Monitor Information Disk and select this monitor's model name as the monitor type. For customers using Windows NT4.0 Monitor setup in Windows NT4.0 is different from Windows 95/98 and does not involve the selection of monitor type. Refer to the Windows NT4.0 instruction manual for further details on adjusting the resolution, refresh rate, and number of colors. Adjusting the monitor's resolution and color number Adjust the monitor's resolution and color number by referring to your computer's instruction manual. The color number may vary according to your computer or video board. The color palette setting and the actual number of colors are as follows: · High Color (16 bit) t 65,536 colors · True Color (24 bit) t about 16.77 million colors In true color mode (24 bit), speed may be slower.
to INPUT1 or INPUT2 connector to AC IN to a power outlet power cord (supplied) Macintosh adapter (supplied)*
Step 1: Connect the media engine to your computer
Turn off the media engine and computer before connecting.
Note Do not touch the pins of the video signal cable connector as this might bend the pins.
to video output
HD15 (RGB) video signal cable (supplied)
Step 4: Turn on the monitor and computer
1 Turn on the media engine.
The display automatically turns on. The indicators of the media engine and display light up in green.
Macintosh or compatible computer * Refer to the supplied "Notes for Macintosh users" for further details.
US
x Connecting to an IBM PC/AT or compatible computer
Step 2: Connect the display and media engine
Turn off the display and media engine before connecting.
1-3
to INPUT1 or INPUT2 connector to video output IBM PC/AT or compatible computer HD15 (RGB) video signal cable (supplied)
2 Turn on the computer.
The installation of your monitor is complete. If necessary, use the monitor's controls to adjust the picture.
to SYSTEM CONNECTOR of the media engine
to SYSTEM CONNECTOR of the display
system connecting cable (2 m) (supplied)
Caution Be sure to install the media engine vertically shown as above. Installing the media engine lying flat may block ventilation, and may cause a malfunction. Note Grasp the plug when connecting the cable.
8
9
Using the stereo speaker
You can listen to music, sounds, and other audio files using the stereo speaker of your monitor. Connect the AUDIO IN jack to the audio output jack of your computer or other audio equipment using the supplied audio cord (stereo miniplug).
Selecting the input signal
You can connect two computers to this monitor using the INPUT 1 and INPUT 2 connectors. To select one of the two computers, use the INPUT button. Press the INPUT button. The input signal and corresponding input indicator, "1" (INPUT 1) or "2" (INPUT 2) change each time you press this button.
INPUT 1 2 OK
Customizing Your Monitor
Before making adjustments
Connect the monitor and the computer, and turn them on. Wait for at least 30 minutes before making adjustments for the best result. You can make numerous adjustments to your monitor using the on-screen menu.
4 V CENTER (page 13) Select the V CENTER menu to adjust the picture's vertical centering.
V CENT ER
25
EX I T
Adjusting the volume
Volume adjustments are made using a separate VOLUME menu from the main menu (page 11).
1 Press the 2 +/ buttons.
The VOLUME menu appears on the screen.
VOL UME
Navigating the menu
Press the MENU button to display the main menu on your screen. See page 12 for more information on using the MENU button.
5 ZOOM (page 14) Select the ZOOM menu to adjust the picture's sharpness according to the input signal's aspect ratio or resolution.
ZOOM ON OF F
EX I T
40
Notes · You cannot select the input signal when displaying the main menu on the screen. · If no signal is input to the selected connector, NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters the power saving mode. If this happens, select the other connector using the INPUT button.
PHA SE
MENU
6 COLOR (page 14) Select the COLOR menu to adjust the color temperature of the picture. This adjusts the tone of the screen.
COLOR 9 30 0K 6 5 00K 5 0 0 0K USER L A D J U ST
2 Press the 2 +/ button to adjust the volume.
The menu automatically disappears after about 3 seconds. 7 MENU POSITION (page 14) Select the MENU POSITION to change the onscreen menu position.
EX I T
MEN U POS I T I ON
US
Using the headphones jack
You can listen to the audio signals from your computer or other audio equipment using headphones. Connect your headphones to the headphones jack. The speaker turns off when headphones are connected to the headphones jack. Adjust the volume of the headphones using the VOLUME menu.
Notes · You cannot adjust the volume when displaying the main menu on the screen. · When your monitor is in low power consumption mode or power saving mode, no sound comes from the speaker.
Use the M(+)/m() and OK buttons to select one of the following menus. See page 12 for more information on using the M(+)/m() and OK buttons. 1 PHASE (page 13) Select the PHASE menu to adjust the phase when the characters or pictures appear fuzzy throughout the entire screen. Adjust the phase after adjusting the pitch. 2 PITCH (page 13) Select the PITCH menu to adjust the pitch when the characters or pictures are unclear in some areas of the screen.
PHA S E
EX I T
1-4
16
8 RESET (page 15) Select the RESET menu to reset the adjustments.
RESE T S CREEN RESE T A L L RESE T
EX I T
P I TCH
EX I T
0
EX I T
3 H CENTER (page 13) Select the H CENTER menu to adjust the picture's horizontal centering.
H CENT ER
50
9 Option (page 15) Select m (option) menu to adjust the monitor's options. The options include: · WIDE STEREO · BASS BOOST · BACKLIGHT · LIGHT SENSOR · POWER SAVE · USER SENSOR · LANGUAGE · MENU LOCK
W I D E S T E R EO
1 2
OF F
EX I T
EX I T
(continued)
10
11
x Using the MENU, M(+)/m(), and OK buttons
1 Display the main menu.
Press the MENU button to display the main menu on your screen.
MENU
Adjusting the contrast (CONTRAST)
Contrast adjustment is made using a separate CONTRAST menu from the main menu (page 11). This setting is stored in memory for the signal from the currently selected input connector.
Eliminating flicker or blurring (PHASE/PITCH)
When the monitor receives an input signal, the automatic picture quality adjustment function of this monitor automatically adjusts the picture position, phase, and pitch, and ensures that a clear picture appears on the screen. For more information about this function, see "Automatic picture quality adjustment function" on page 18. For some input signals, this function may not completely adjust the picture position, phase, and pitch. In this case, you can manually set these adjustments according the following instructions. If you manually set these adjustments, they are stored in memory and automatically recalled whenever the monitor receives the same input signals. These settings may have to be repeated if you change the input signal after reconnecting your computer.
8 Press the M(+)/m() buttons to select
and press the OK button. The PHASE menu appears on the screen.
(PHASE)
9 Press the M(+)/m() buttons until the screen color
becomes uniform. Adjust so that the horizontal stripes are at a minimum.
1 Press the 6 (contrast) button.
The CONTRAST menu appears on the screen.
CONTRAS T
70
2 Select the menu you want to adjust.
Press the M(+)/m() buttons to display the desired menu. Press the OK button to select the menu item.
INPUT
4 8 . 4 kHz / 6 0Hz
10 Click [END] on the screen to turn off the test pattern.
To reset the automatic picture quality adjustment Select SCREEN RESET and activate it using the RESET menu. See page 15 for more information on using the RESET menu.
,
1 2 OK
Horizontal frequency of the current input signal
Vertical frequency of the current input signal
1 Set the resolution to 1024 × 768 on the computer. 2 Load the Utility Disk.
Use the appropriate disk for your computer. For Windows 95/98 Windows Monitor Information Disk/Utility Disk For Macintosh Macintosh Utility Disk
Displaying the current input signal The horizontal and vertical frequencies of the current input signal are displayed in the CONTRAST and BRIGHTNESS menu.
2 Press the M(+)/m() buttons to adjust the contrast. 3 Adjust the menu.
Press the M(+)/m() buttons to make the adjustment. Then press the OK button to return to the previous menu.
INPUT
Adjusting the picture position (H CENTER/V CENTER)
If the picture is not in the center of the screen, adjust the picture's centering as follows. These settings may have to be repeated if you change the input signal after reconnecting your computer.
The menu automatically disappears after about 3 seconds.
US
,
1 2 OK
Adjusting the black level of an image (BRIGHTNESS)
Brightness adjustment is made using a separate BRIGHTNESS menu from the main menu (page 11). This setting is stored in memory for the signal from the currently selected input connector.
3 Start the Utility Disk and display the test pattern.
For Windows 95/98 Click [Utility Disk] t [Windows]/[Utility.exe]. For Macintosh Click [Utility Disk] t [SONY-Utility].
1 Start the Utility Disk and display the test pattern.
Repeat steps 2 and 3 of "Eliminating flicker or blurring (PHASE/PITCH)."
4 Press the MENU button.
The main menu appears on the screen.
1-5
4 Close the menu.
Press the MENU button once to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 30 seconds.
MENU
2 Press the MENU button.
The main menu appears on the screen. (PITCH)
1 Press the 8 (brightness) button.
The BRIGHTNESS menu appears on the screen.
B R I GHT NESS
5 Press the M(+)/m() buttons to select
and press the OK button. The PITCH menu appears on the screen.
3 Press the M(+)/m() buttons to select
6 Press the M(+)/m() buttons until the screen color
50
(H CENTER) or (V CENTER) and press the OK button. The H CENTER or V CENTER menu appears on the screen.
becomes uniform. Adjust so that the vertical stripes disappear.
4 Move the picture up, down, left, or right until the
frame at the perimeter of the test pattern disappears. Press the M(+)/m() buttons to adjust the picture's centering using the H CENTER menu for horizontal adjustment, or the V CENTER menu for vertical adjustment.
4 8 . 4 kHz /
6 0Hz
x Resetting the adjustments
You can reset the adjustments using the RESET menu. See page 15 for more information on resetting the adjustments.
Horizontal frequency of the current input signal
Vertical frequency of the current input signal
2 Press the M(+)/m() buttons to adjust the
brightness.
5 Click [END] on the screen to turn off the test pattern. 7 Press the OK button.
The main menu appears on the screen. If horizontal stripes are observed over the entire screen, adjust the phase as the next step.
If the screen is too bright
Adjust the backlight. For more information about adjusting the backlight see "Adjusting the backlight" on page 16. The menu automatically disappears after about 3 seconds.
Note You can adjust neither contrast nor brightness when displaying the main menu on the screen.
12
13
Displaying a low-resolution signal at the actual resolution (ZOOM)
This monitor is preset at the factory to display pictures on the screen in full, irrespective of the picture's mode or resolution. You can also view the picture at its actual resolution.
4 If necessary, fine tune the color temperature.
First press the M(+)/m() buttons to select ADJUST and press the OK button. Then press the M(+)/m() buttons to select R (Red) or B (Blue) and press the OK button, and then press the M(+)/m() buttons to adjust the color temperature. Since this adjustment changes the color temperature by increasing or decreasing the R and B components with respect to G (green), the G component is fixed.
USE R AD J UST MENT R G B 16 8 17 0 17 5 EX I T
Resetting the adjustments (RESET)
This monitor has the following two reset methods. Use the RESET menu to reset the adjustments.
Additional settings (Option)
You can adjust the following options: · WIDE STEREO · BASS BOOST · BACKLIGHT · LIGHT SENSOR · POWER SAVE · USER SENSOR · LANGUAGE · MENU LOCK
1 Press the MENU button.
The main menu appears on the screen.
1 Press the MENU button.
The main menu appears on the screen.
2 Press the M(+)/m() buttons to select
2 Press the M(+)/m() buttons to select
and press the OK button. The ZOOM menu appears on the screen.
(ZOOM)
(RESET) and press the OK button. The RESET menu appears on the screen. Reset the settings according to the following instructions.
1 Press the MENU button. Resetting the adjustment data most appropriately for the current input signal
Press the M(+)/m() buttons to select SCREEN RESET and press the OK button. The automatic picture quality adjustment function of this monitor automatically adjusts the picture position, phase, and pitch, to the most appropriate value. If this function is activated, the phase is automatically adjusted whenever the monitor receives the same input signal. The RESET menu is automatically returned to the main menu after the adjustment data is reset. The main menu appears on the screen.
3 Press the m() button to select OFF.
The input signal is displayed on the screen at its actual resolution.
2 Press the M(+)/m() buttons to select m.
The option menu appears on the screen.
If you fine tune the color temperature, the new color setting is stored in memory for USER ADJUSTMENT and automatically recalled whenever USER is selected. The USER ADJUSTMENT setting is common to both the input signals. If you change the user adjustment setting for one input signal, the setting for the other input signal is also changed.
3 Press the M(+)/m() buttons to select the desired
option item and press the OK button. Adjust the selected option item according to the following instructions.
Increasing the soundscape (wide stereo function)
This adjustment makes use of the DSP and creates the illusion of the built-in stereo speaker being further away than it actually is, thus enhancing sound presence. First press the M(+)/m() buttons to select (WIDE STEREO) and press the OK button. Then press the M(+)/m() buttons to select either 2, 1, or OFF. The wide stereo function is used to increase the soundscape. Selecting 1 or 2 increases incrementally the soundscape effect toward the front of the monitor.
Notes · If your connected computer or audio equipment uses special sound functions, such as surround sound, be sure to turn these functions off. If these functions are being used with the wide stereo function of this monitor, the wide stereo function may not function properly and thus not produce the desired sound effect. · This function is automatically turned off when you use headphones. However, in this case, the indication in the WIDE STEREO menu does not change. · The wide stereo function allows you to increase the soundscape by converting the analog signals into digital. The sound may be distorted depending on the input signal and music. In this case, decrease the volume or set the wide stereo function to OFF.
To display the picture on the screen in full Select ON in step 3.
Changing the menu's position (MENU POSITION)
You can change the menu position if it is blocking an image on the screen.
Resetting all of the adjustment data for all input signals
Press the M(+)/m() buttons to select ALL RESET and press the OK button. The RESET menu is automatically returned to the main menu after the adjustment data is reset.
US
Adjusting the color temperature (COLOR)
The COLOR settings allow you to adjust the picture's color temperature by changing the color level of the white color field. Colors appear reddish if the temperature is low, and bluish if the temperature is high. 9300K is generally suitable for word processing and other text oriented applications, and 6500K is generally suitable for video images. You can set the color temperature to 5000K, 6500K, 9300K or user adjustment.
1 Press the MENU button.
The main menu appears on the screen.
To cancel resetting
(MENU Press the M(+)/m() buttons to select and press the OK button. The RESET menu returns to the main menu without resetting the adjustment data.
1-6
2 Press the M(+)/m() buttons to select
POSITION) and press the OK button. The MENU POSITION menu appears on the screen.
3 Press the M(+)/m() buttons to select the desired
position. There are three positions each for the top of the screen and the bottom of the screen, and one for the screen center.
1 Press the MENU button.
The main menu appears on the screen.
2 Press the M(+)/m() buttons to select
and press the OK button. The COLOR menu appears on the screen.
(COLOR)
Boosting the bass (bass boost function)
This option increases the bass output of the speaker. First press the M(+)/m() buttons to select (BASS BOOST) and press the OK button. Then press the M(+)/m() buttons to select either ON or OFF.
3 Press the M(+)/m() buttons to select the desired
color temperature. The preset color temperatures are 5000K, 6500K, and 9300K. Since the default setting is 9300K, the whites will change from a bluish hue to a reddish hue as the temperature is lowered to 6500K and 5000K. You can set separate color temperatures for each of the video input signals.
(continued)
14
15
Adjusting the backlight
If the screen is too bright, adjust the backlight. First press the M(+)/m() buttons to select (BACKLIGHT) and press the OK button. Then press the M(+)/m() buttons to adjust the desired light level.
Selecting the on-screen menu language
English, German, French, Spanish, Italian and Japanese versions of the on-screen menus are available. The default setting is English. First press the M(+)/m() buttons to select (LANGUAGE) and press the OK button. Then press the M(+)/m() button to select a language. · ENGLISH · DEUTSCH: German · FRANÇAIS: French · ESPAÑOL: Spanish · ITALIANO: Italian · : Japanese
Technical Features
Power saving function (user sensor/power saving mode)
This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically enter the power saving mode. It automatically enters the low power consumption mode when the user sensor detects the absence of a user. Power consumption state normal operation 1 low power consumption mode 2 power saving mode 1 (power): off AC power: off Power consumption 35 W 4W 3W 3W 0W AC power indicator green green orange red off 1 (power) indicator green green and orange alternate orange off off
Automatically adjusting the screen brightness (light sensor)
This monitor is provided with a sensor to detect the brightness of the surrounding area (light sensor). This sensor is used to automatically adjust the brightness of the screen. First press the M(+)/m() buttons to select (LIGHT SENSOR) and press the OK button. Then press the M(+)/m() buttons to select either ON or OFF. When you select ON, the monitor automatically adjusts the screen brightness according to the brightness of the surroundings. For more information about this function, see "Automatic brightness adjustment function (light sensor)" on page 18.
Note If this function is set to ON, the value of the BACKLIGHT menu does not change. If the screen brightness is still not appropriate after the automatic adjustment, you can manually adjust the backlight. After the backlight adjustment is made, the monitor automatically adjusts the screen brightness in accordance with the new backlight value.
Locking the menus and controls
You can protect adjustment data by locking the menus and controls. First press the M(+)/m() buttons to select (MENU LOCK) and press the OK button. Then press the M(+)/m() buttons and select ON. Only the 1 (power) switch, and (MENU LOCK) of the option menu will operate. If any other items are selected, the mark appears on the screen.
To cancel the menu lock Repeat the procedure above and set and
1 Low power consumption mode (user sensor)
When the user sensor in the monitor detects the absence of a user, the monitor enters low power consumption mode after about 20 seconds. In low power consumption mode, the monitor is in a power saving state and shuts off power to all circuitry (except for that of the sensors) regardless of the setting of the computer. The monitor returns to normal operation mode when the presence of a user is detected by the user sensor. When the monitor enters the power saving mode (as set according to the computer's settings), the power saving mode takes precedence over the low power consumption mode. In this case, the monitor stays in the power saving mode regardless of the presence or absence of a user. To return the monitor to normal operation mode, reset the computer's power saving mode.
Note The user sensor detects the presence/absence of a user up to a distance of approximately 60 cm from the screen surface. However, this distance may vary depending on the user's clothes or the brightness of the surrounding area. If user detection fails due to the ambient conditions of the surrounding area, set the user sensor to OFF. If your monitor does not automatically return from low power consumption mode due to the failure of the user sensor to detect the presence of a user, press the 1 (power) switch twice to turn the monitor off and then on.
2 Power saving mode
DPMS defines three power saving states according to the state of the sync signals supplied from the computer. This monitor's power consumption is input at approximately 3 W in all of these states if the power saving function is set to ON. When your computer enters in the power saving mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters power saving mode. Power saving state suspend (sleep)* standby (sleep)* active off (deep sleep)* Sync signal state horizontal: on / vertical: off horizontal: off / vertical: on horizontal: off / vertical: on
Setting up the power saving mode
This monitor has a function which enables it to enter the power save mode automatically according to the power saving settings of the computer. You can prevent the monitor from entering the power saving mode by setting the following option to OFF. First press the M(+)/m() buttons to select ZZ... (POWER SAVE) and press the OK button. Then press the M(+)/m() buttons to select either ON or OFF.
(MENU LOCK) to OFF.
US
1-7
Using the user sensor
The user sensor function enables the monitor to enter the low power consumption mode when no one is present in front of the monitor. First press the M(+)/m() buttons to select (USER SENSOR) and press the OK button. Then press the M(+)/m() buttons to select either ON or OFF. If you select ON, the monitor automatically enters the low power consumption mode when you move away from the front of the monitor. For more information about the low power consumption mode, see "Power saving function (user sensor/power saving mode)" on page 17.
* "Sleep" and "deep sleep" are power saving modes defined by the Environmental Protection Agency. Note The power saving function may not work normally if sync signals other than those listed above are supplied. In such a case, set the power saving function to OFF.
16
17
Automatic brightness adjustment function (light sensor)
This monitor is provided with a feature to automatically adjust the screen brightness according to the brightness of the surroundings. The brightness of the backlight is set to the most appropriate level by setting the light sensor to ON. The default setting of the brightness of the backlight is set to its maximum. When the light sensor setting is set to ON, the monitor adjusts the brightness of the backlight linearly from its lower- to upper-limit values. When the user adjusts the backlight, the backlight brightness is automatically adjusted between the user adjustment value and the upper- and lower-limit values.
Backlight brightness Maximum Automatic brightness adjustment after user adjustment
If CABLE DISCONNECTED appears on the screen
Troubleshooting
Before contacting technical support, refer to this section.
This indicates that the video signal cable has been disconnected from the currently selected connector.
I NFORMA T I ON
On-screen messages
If there is something wrong with the input signal, one of the following messages appears on the screen. To solve the problem, see "Trouble symptoms and remedies" on page 20.
CAB L E D I SCONNECT ED I NPUT : 1 GO TO POWER SAVE
If OUT OF SCAN RANGE appears on the screen
User adjustment value
This indicates that the input signal is not supported by the monitor's specifications. Check the following items.
Preset automatic adjustment
I NFORMA T I ON OUT OF SCAN RANGE x x . x kHz / x xHz
INPUT: This indicates the currently selected connector (INPUT: 1 or INPUT: 2). GO TO POWER SAVE The monitor will enter the power saving mode after about 4 seconds from the message is displayed.
Minimum
Brightness during user adjustment
Brightness of surroundings User-specified brightness value
Automatic picture quality adjustment function
When the monitor receives an input signal, it automatically matches the signal to one of the factory preset modes stored in the monitor's memory to provide a high quality picture at the center of the screen. (See Appendix for a list of the factory preset modes.) For input signals that do not match one of the factory preset modes, the automatic picture quality adjustment function of this monitor automatically adjusts the picture position, phase, and pitch, and ensures that a clear picture appears on the screen for any timing within the monitor's frequency range (horizontal: 30 61 kHz, vertical: 50 85 Hz). Consequently, the first time the monitor receives input signals that do not match one of the factory preset modes, the monitor may take a longer time than normal for displaying the picture on the screen. This adjustment data is automatically stored in memory so that next time, the monitor will function in the same way as when the monitor receives the signals that match one of the factory preset modes. In all modes as above, if the picture is adjusted, the adjustment data is stored as a user mode and automatically recalled whenever the same input signal is received.
Note on the adjusting the phase If the automatic picture quality adjustment function is activated, the picture moves slightly whenever the monitor receives the input signal, regardless of the stored adjustment. Note While the automatic picture quality adjustment function is activated, only the 1 (power) switch, and INPUT button will operate.
If "xx.x kHz/xx Hz" is displayed This indicates that either the horizontal or vertical frequency is not supported by the monitor's specifications. The figures indicate the horizontal and vertical frequencies of the current input signal. The horizontal frequencies above 100 kHz and the vertical frequencies above 100 Hz are represented by 99.9 kHz and 99 Hz, respectively. If "RESOLUTION > XGA" is displayed This indicates that the resolution is not supported by the monitor's specifications.
US
If NO INPUT SIGNAL appears on the screen
This indicates that no signal is input, or that no signal is input from the currently selected connector.
I NFORMA T I ON NO I NPUT S I GNA L I NPUT : 1 GO TO POWER SAVE
1-8
INPUT: This indicates the currently selected connector (INPUT: 1 or INPUT: 2). GO TO POWER SAVE The monitor will enter the power saving mode after about 4 seconds from the message is displayed.
18
19
Trouble symptoms and remedies
If a problem is caused by the connected computer or other equipment, please refer to the connected equipment's instruction manual. Use the self-diagnosis function (page 22) if the following recommendations do not resolve the problem. Symptom No picture If the AC power indicator is not lit If the AC power indicator is red If the 1 (power) indicator is not lit, or if the 1 (power) indicator will not light up when the 1 (power) switch is pressed If the 1 (power) indicator is green or flashing orange If the 1 (power) indicator is alternating between green and orange If CABLE DISCONNECTED appears on the screen, or the AC power indicator is flashing red · Check that the power cord is properly connected. · Check that the 1 (power) switch is in the "on" position. · Check that the 1 (power) switch is in the "on" position. · Check that the AC power switch is in the "on" position. · Check that the system connecting cable is properly connected and all plugs are firmly seated in their sockets (page 8). · Use the self-diagnostics function (page 22). Check these items
Symptom Picture flickers, bounces, oscillates, or is scrambled
Check these items · Adjust the pitch and phase (page 13). · Isolate and eliminate any potential sources of electric or magnetic fields such as other monitors, laser printers, electric fans, fluorescent lighting, or televisions. · Move the monitor away from power lines or place a magnetic shield near the monitor. · Try plugging the monitor into a different AC outlet, preferably on a different circuit. xProblems caused by the connected computer or other equipment · Check your graphics board manual for the proper monitor setting. · Confirm that the graphics mode (VESA, Macintosh 19" Color, etc.) and the frequency of the input signal are supported by this monitor (Appendix). Even if the frequency is within the proper range, some video boards may have a sync pulse that is too narrow for the monitor to sync correctly. · Adjust the computer's refresh rate (vertical frequency) to obtain the best possible picture.
Picture is fuzzy Picture is ghosting
· Adjust the brightness and contrast (page 12). · Adjust the pitch and phase (page 13). · Eliminate the use of video cable extensions and/or video switch boxes. · Check that all plugs are firmly seated in their sockets. · Adjust the pitch and phase (page 13). · Adjust the picture position (page 13). Note that some video modes do not fill the screen to the edges. · Set the zoom setting to ON (page 14). xProblems caused by the connected computer or other equipment · Set the computer's resolution to the screen's resolution.
· The monitor cannot return from low power consumption mode because the user sensor fails to detect the presence of a user. Press the 1 (power) switch twice to turn the monitor off and then on. If you set the user sensor to OFF, the monitor does not enter low power consumption mode (page 16). · Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets (page 8). · Check that the video input connector's pins are not bent or pushed in. · A non-supplied video signal cable is connected. If you connect a non-supplied video signal cable, CABLE DISCONNECTED appears on the screen before entering the power saving mode. This is not a malfunction. · Check that the system connecting cable is properly connected and all plugs are firmly seated in their sockets (page 8). · Press the AC power switch twice to turn the monitor off and then on. · Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets (page 8). · Check that the input select setting is correct (page 10). · Check that the video input connector's pins are not bent or pushed in. xProblems caused by the connected computer or other equipment · The computer is in the power saving mode. Try pressing any key on the keyboard or moving the mouse. · Check that the computer's power is "on." · Check that the graphic board is completely seated in the proper bus slot.
Picture is not centered or sized properly The picture is too small
Wavy or elliptical pattern (moire) is visible Color is not uniform White does not look white Monitor buttons do not operate ( appears on the screen) The monitor turns off after a while
· Adjust the pitch and phase (page 13). · Adjust the pitch and phase (page 13). · Adjust the color temperature (page 14). · If the menu lock is set to ON, set it to OFF (page 16). · Set the power saving function to OFF (page 16). · Set the user sensor to OFF (page 16). xProblems caused by the connected computer or other equipment · Set the computer's power saving setting to off.
US
If NO INPUT SIGNAL appears on the screen, or the 1 (power) indicator is orange
1-9
20
Displaying this monitor's name, serial number, and date of manufacture.
While the monitor is receiving a video signal, press and hold the MENU button for more than 5 seconds to display this monitor's information box.
MENU
If OUT OF SCAN RANGE appears on the screen
xProblems caused by the connected computer or other equipment · Check that the video frequency range is within that specified for the monitor. If you replaced an old monitor with this monitor, reconnect the old monitor and adjust the frequency range to the following: Horizontal: 30 61 kHz Vertical frequency: 50 85 Hz (only XGA mode at 75 Hz) · If you replaced an old monitor with this monitor, reconnect the old monitor and do the following. Install the Windows Monitor Information Disk (page 9) and select this monitor ("SDM-N50") from among the Sony monitors in the Windows 95/98 monitor selection screen. · Check and refer to the supplied "Notes for Macintosh users."
If any problem persists, call your authorized Sony dealer and give the following information: · Model name: SDM-N50 · Serial number · Name and specifications of your computer and graphics board.
If using Windows 95/98
If using a Macintosh system
Example
INFORMATION MODEL : SDM-N50 SER NO : 1234567 MANUFACTURED : 1999-52
Model name Serial number Week and year of manufacture
21
Self-diagnosis function
This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer(s), the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard or moving the mouse.
Specifications
Panel type: a-Si TFT Active Matrix Picture size: 15 inch (38 cm) RGB operating frequency* Horizontal: 30 61 kHz Vertical: 50 85 Hz Resolution Horizontal: Max.1024 dots Vertical: Max.768 lines Input signal levels RGB video signal 0.700 Vp-p, 75 , positive SYNC signal TTL level, 2 k, positive or negative (Separate horizontal and vertical, or composite sync) 0.3 Vp-p, 75, negative (Sync on green) Audio output 2W × 2 Headphones jack Stereo minijack Accepts impedance of 16 48 AUDIO IN jack Stereo minijack Accepts impedance of 16 k Accepts level 0.5 Vrms Power requirements 100 240 V, 50 60 Hz, 0.55 0.3 A Power consumption Max. 35 W Operating temperature 5 35 °C Dimensions (width/height/depth) Display (upright): Approx. 356 × 347 × 185 mm (14 1/8 × 13 3/4 × 7 3/8 inches) Media engine (without stand): Approx. 45 × 180 × 180 mm (1 13/16 × 7 1/8 × 7 1/8 inches) Media engine (with stand): Approx. 94 × 185 × 180 mm (3 3/4 × 7 3/8 × 7 1/8 inches) Mass Display: Approx. 2.7 kg (5 lb 15 oz) Media engine (with stand): Approx. 0.85 kg (1 lb 14 oz) Plug & Play DDC1/DDC2B/DDC2Bi Accessories See page 8. Input signal format * Recommended horizontal and vertical timing condition · Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 µs, whichever is larger. · Horizontal blanking width should be more than 2.3 µsec. · Vertical blanking width should be more than 450 µsec. Design and specifications are subject to change without notice. LCD panel
1 (power) indicator
If the 1 (power) indicator is green 1 Turn off the AC power switch and disconnect the
video signal cables from the INPUT1 and INPUT2 connectors of the media engine.
2
Press the AC power switch twice to turn the monitor off and then on.
If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cables and check the condition of your computer(s). If the color bars do not appear, there is a potential monitor failure. Inform your authorized Sony dealer of the monitor's condition.
1-10
If the 1 (power) indicator is flashing orange
Press the 1 (power) switch twice to turn the monitor off and then on. If the 1 (power) indicator lights up green, the monitor is working properly. If the 1 (power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor's condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and graphic board.
22
SECTION 2 DISASSEMBLY
2-1. U BOARD REMOVAL
1 Open these hinge covers (F) and (R) by the
SDM-N50
screw driver and so on. * When open the hinge cover (R), these claws in figure would be break so replace new parts. Hinge cover (F)
Hinge cover (R)
Claws
Shield case U
6 Remove the U board
in the direction of allow.
5 Three screws
(+BVTP 3 x 8)
2 Two screws
(+PS 4 x 6) Cushion
CN404 CN406 CN405
CN402
4 Base 3 Five screws
(+KTP 3 x 14)
2-2. BASE ASSEMBLY REMOVAL
* Remove the U board refering 2-1.
2 Two screws 1 Two screws
(+P 3 x 5)
(+P 3 x 5)
4 Base assembly
CN406 CN402
3 Base hinge
Cushion LCD module (TFT)
2-1
SDM-N50
2-3. B BOARD REMOVAL
1 Three screws 2 Remove the rear cover after move it in
(Tapping screw 3 x 8)
the direction of allow A and also remove concavities.
Four concavities
4 Shield case (B) 9 Screw
A
3 Three screws
(0 plate special head)
8 BH1 harness assembly
(0 plate special head)
CN508
CN501
CN502
CN507
5 Two screws
10 B board
CN504
(+P 2 x 4) 6 Cable holder (B)
7 Cable holder (A)
Four claws
Cushion
LCD module (TFT)
2-2
SDM-N50
2-4. H BOARD REMOVAL
5 Cover holder
1 Three screws
(+BVTP 3 x 6)
2 Earth (H) 2 Earth (H)
3 H board
CN501
LCD module (TFT)
4 BH1 harness assembly
Cushion
2-5. LCD MODULE (TFT) REMOVAL
* Remove the B and H boards refering 2-3 and 2-4.
1 Remove the LCD module (TFT) in the
direcition of allow A horizontally.
A
Cushion Front cover assembly
2-3
SDM-N50
2-6. A BOARD REMOVAL
3 Four screws
(HD 15)
CN705
5 Three connectors
CN701 CN702
(CN705, CN701, CN702)
4 Three screws
(+P 3 x 5)
1 Four screws
(+BVTP 3 x 12)
6 A board
2 Case (L)
2-7. G BOARD REMOVAL
* Remove A board refering 2-6.
5 Remove the terminal board assembly
in the direction of allow b .
1 Four screws 6 Remove the G board in the
4 Remove the case in the
direction of allow a . direction of allow C .
(+P 3 x 5)
b
CN703
c a
CN704
2 Two earth wires 3 Two connectors
(CN703, CN704)
Chassis plate assembly
2-4
SECTION 3 ADJUSTMENTS
Connect the personal computer, monitor, and signal generator as shown below, and control the monitor.
Signal generator (VG-823, etc.)
SDM-N50
TO INPUT-1
Computer for jig TO CN107 CONNECTOR (A Board) * Maintain the Aging mode for over 30 minutes.
· Preset mode adjustment Confirm the screen by below three kinds of the modes within preseted frequency. Signal mode 1. MODE 0 (640X480 60Hz) 2. MOD