Text preview for : E5063A_Assembly E5063A Disassembly Procedure c20140502 [124].pdf part of Agilent E5063A Assembly E5063A Disassembly Procedure c20140502 [124] Agilent E5063A_Assembly E5063A Disassembly Procedure c20140502 [124].pdf
Back to : E5063A_Assembly E5063A Di | Home
E5063A
Dis-assembly Procedure
Rev.
Reverse Flow Dis-assembly Procedure Menu
Click the hyperlink below for any choice of dis-assembly procedure:
1. LCD
2. SSD
3. CPU Module
4. Display Board
5. A1 Module
6. Analog Board
DIS-ASSEMBLY PROCEDURE MENU Rev. A
LCD
Dis-Assembly Procedure
Note:
1. Torque value shown in this document is only for reference and only used during
assembly.
LCD - DIS-ASSEMBLY PROCEDURE a60 Rev. A
4 Remove Trip Strip
Remove
3
HANDLE ASSEMBLY
1 Remove screw (4ea) and
Standoff Foots (4ea)
Remove screw (4ea) 2
1 2 3 4
LCD - LCD DIS-ASSEMBLY (1) a70 Rev. A
Remove
3a
screw (7ea)
Remove Front sub-assy 1
3b
2
Disconnect flat cable of
Front Panel Ass'y from
CPU Module
1 2 3
LCD - LCD DIS-ASSEMBLY (2) a80 Rev. A
2 Disconnect
1 Open
1 2
LCD - LCD DIS-ASSEMBLY (3) a90 Rev. A
Disconnect 1
2 Open
1 2
LCD - LCD DIS-ASSEMBLY (4) b10 Rev. A
3 Remove
Remove
1
screw (6ea)
2 Disconnect
1 2 3
LCD - LCD DIS-ASSEMBLY (5) b20 Rev. A
1 Disconnect (5ea) 2 Open (3ea)
Remove
3
screw (2ea)
1 2 3
LCD - LCD DIS-ASSEMBLY (6) b30 Rev. A
2
2 Remove screw (4ea)
4
1
3
LCD sub-assembly 1
1 2
LCD - LCD DIS-ASSEMBLY (7) b40 Rev. A
SSD
Dis-Assembly Procedure
Note:
1. Torque value shown in this document is only for reference and only used during
assembly.
SSD - DIS-ASSEMBLY PROCEDURE b60 Rev. A
Remove
3
HANDLE ASSEMBLY
1 Remove screw (4ea) and
Standoff Foots (4ea)
Remove screw (4ea) 2
1 2 3
SSD - HDD DIS-ASSEMBLY (1) b70 Rev. A
Cut (4ea) 2
1 Cut
1 2
SSD - HDD DIS-ASSEMBLY (2) b80 Rev. A
1 Disconnect (2ea)
1
SSD - HDD DIS-ASSEMBLY (3) b90 Rev. A
Slowly Slide out the
2 Sub-Assembly SSD
Remove
1
screw (2ea)
1 2
SSD - HDD DIS-ASSEMBLY (4) c10 Rev. A
Cut (3ea) 1
2 Disconnect
1 2
SSD - HDD DIS-ASSEMBLY (5) c20 Rev. A
3 SSD
1 Remove screw (4ea)
Remove 2
1 2 3
SSD - HDD DIS-ASSEMBLY (6) c30 Rev. A
CPU Module
Dis-Assembly Procedure
Note:
1. Torque value shown in this document is only for reference and only used during
assembly.
CPU MODULE - DIS-ASSEMBLY PROCEDURE c50 Rev. A
Remove
3
HANDLE ASSEMBLY
1 Remove screw (4ea) and
Standoff Foots (4ea)
Remove screw (4ea) 2
1 2 3
CPU MODULE - CPU MODULE DIS-ASSEMBLY (1) c60 Rev. A
Remove 4
Cut (4ea) 2
1 Cut
Remove
3
screw (2 ea)
1 2 3 4
CPU MODULE - CPU MODULE DIS-ASSEMBLY (2) c70 Rev. A
1 Disconnect
2 Open
1 2
CPU MODULE - CPU MODULE DIS-ASSEMBLY (3) c80 Rev. A
DISCONNECT All cables
1 on CPU Module
1 1
1
1
1
1
1 1
1
CPU MODULE - CPU MODULE DIS-ASSEMBLY (4) c90 Rev. A
Slowly Slide out the
2 Sub-Assembly SSD
Remove
1
screw (2ea)
1 2
CPU MODULE - CPU MODULE DIS-ASSEMBLY (5) d10 Rev. A
Remove screw (3ea) 2
Remove
3
CPU Module
1 Remove screw (3ea)
1 2 3
CPU MODULE - CPU MODULE DIS-ASSEMBLY (6) d20 Rev. A
Display Board
Dis-Assembly Procedure
Note:
1. Torque value shown in this document is only for reference and only used during
assembly.
DISPLAY BOARD - DIS-ASSEMBLY PROCEDURE d40 Rev. A
4 Remove Trip Strip
Remove
3
HANDLE ASSEMBLY
1 Remove screw (4ea) and
Standoff Foots (4ea)
Remove screw (4ea) 2
1 2 3 4
DISPLAY BOARD - DISPLAY BOARD DIS-ASSEMBLY (1) d50 Rev. A
Remove
3a
screw (7ea)
Remove Front sub-assy 1
3b
2
Disconnect flat cable of
Front Panel Ass'y from
CPU Module
1 2 3
DISPLAY BOARD - DISPLAY BOARD DIS-ASSEMBLY (2) d60 Rev. A
2 Disconnect
1 Open
1 2
DISPLAY BOARD - DISPLAY BOARD DIS-ASSEMBLY (3) d70 Rev. A
Connect
1
(2ea)
2 Remove screw (2ea)
1 2
DISPLAY BOARD - DISPLAY BOARD DIS-ASSEMBLY (4) d80 Rev. A
Remove
Display Board 3
Remove (2ea) 2
1 Remove (2ea)
1 2 3
DISPLAY BOARD - DISPLAY BOARD DIS-ASSEMBLY (5) d90 Rev. A
A1 Module
Dis-Assembly Procedure
Note:
1. Torque value shown in this document is only for reference and only used during
assembly.
A1 MODULE - DIS-ASSEMBLY PROCEDURE e20 Rev. A
4 Remove Trip Strip
Remove
3
HANDLE ASSEMBLY
1 Remove screw (4ea) and
Standoff Foots (4ea)
Remove screw (4ea) 2
1 2 3 4
A1 MODULE - A1 MODULE DIS-ASSEMBLY (1) e30 Rev. A
Remove
3a
screw (7ea)
Remove Front sub-assy 1
3b
2
Disconnect flat cable of
Front Panel Ass'y from
CPU Module
1 2 3
A1 MODULE - A1 MODULE DIS-ASSEMBLY (2) e40 Rev. A
2 Disconnect
1 Open
1 2
A1 MODULE - A1 MODULE DIS-ASSEMBLY (3) e50 Rev. A
Remove screw (2ea) 1
2 Remove screw (3ea)
1 2
A1 MODULE - A1 MODULE DIS-ASSEMBLY (4) e60 Rev. A
Remove A1 Board 1
1
A1 MODULE - A1 MODULE DIS-ASSEMBLY (5) e70 Rev. A
Analog Board
Dis-Assembly Procedure
Note:
1. Torque value shown in this document is only for reference and only used during
assembly.
ANALOG BOARD - DIS-ASSEMBLY PROCEDURE e90 Rev. A
Remove Trim Side
1
21 inlb 2
Attach T-384162, Cart arm
1 2
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (1) f10 Rev. A
4 Remove Trip Strip
Remove
3
HANDLE ASSEMBLY
1 Remove screw (4ea) and
Standoff Foots (4ea)
Remove screw (4ea) 2
1 2 3 4
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (2) f20 Rev. A
Remove
3a
screw (7ea)
Remove Front sub-assy 1
3b
2
Disconnect flat cable of
Front Panel Ass'y from
CPU Module
1 2 3
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (3) f30 Rev. A
2 Disconnect
1 Open
1 2
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (4) f40 Rev. A
Connect
1
(2ea)
2 Remove screw (2ea)
1 2
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (5) f50 Rev. A
Remove
Display Board 3
Remove (2ea) 2
1 Remove (2ea)
1 2 3
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (6) f60 Rev. A
Remove screw (2ea) 1
2 Remove screw (3ea)
1 2
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (7) f70 Rev. A
Remove A1 Board 1
1
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (8) f80 Rev. A
3 Remove
Remove screw (7ea) 2
1 Remove washer and nuts (3ea)
1 2 3
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (9) f90 Rev. A
1 Disconnect (2ea)
2 Cut
1 2
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (10) g10 Rev. A
Remove screw (11ea) 1
Remove Analog Board 4
Remove screw 2 3 Disconnect
1 2 3 4
ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (11) g20 Rev. A
E5063A
Assembly Procedure
Rev.
GENERAL INSTRUCTIONS:
1. Hand start (only a few turns) for all screws or nuts prior to torqueing.
2. During screws/ nuts torqueing, perform in X-tightening sequences.
3. All SMA cable connections require 9.5 lbin torque.
GENERAL AND SPECIAL INSTRUCTIONS a40 Rev. A
1 E5061-60006
2 1400-0584 (2ea)
1 2
ATTACH MOUNT CABLE-TIE TO CHASSIS a50 Rev. A
E5063-00604 1
2 0515-0430 (2ea)
M3L6 PAN
9inlb
1 2
ATTACH PANEL PCA SLOT a60 Rev. A
0363-0310
1 RFI STRIP-FINGERS
16 segment 21 segment
32segment
1
ATTACH STRIP FINGER TO CHASSIS a70 Rev. A
0515-0430 (11ea)
M3L6 PAN 3
9inlb
After assy condition
E5061-61612 1
5
0515-1946 "Analog M" cable
4 E5061-61611 needs to be slotted
M3L6 FLAT
through the chassis
9inlb
open hole first before
2 E5063-66610 connecting to A10
Board.
1 2 3 4 5
INSTALL ANALOG MOTHERBOARD a80 Rev. A
Use T-384186 to hold Angle E5061-01207 2
Stopper
3 0515-0430 (2ea)
M3L6 PAN 9inlb
Cables are divided with thin groups Pull and push on the cables while
1 tightening screw
to be flat and temporary clamp with
Jig (T-384163) to positioning its location.
1 2 3
INSTALL ANGLE a90 Rev. A
1
T-384163
Remove jig after fixed the
plate to chassis.
Attention: Ensure cable do not squeeze by plate
1
ANGLE ASSEMBLY INSPECTION b10 Rev. A
E5071-61628 (2ea)
FAN SUB-ASSEMBLY 1 FAN ASSY Middle Speed
Route wire from fan as below
Left Fan Right Fan
1
FAN ASSEMBLY (1) b20 Rev. A
Standoff is on
upper left hand side
0361-1881 8ea
2 Push Rivet
P4080-W
Note:
Ensure Fan Direction
is correct
1 E5061-01223
1 2
FAN ASSEMBLY (2) b30 Rev. A
0460-0169 3ea
1 Tape
1400-0249
2
Cable Tie Pull both wires before
paste on tape
BAD Sample
Note: Make sure
no gap! Tape must
stick properly.
Tie the wire with cable Good Sample
tie as showed in picture
and ensure wire is push
1 2 inward
FAN ASSEMBLY (3) b40 Rev. A
ATTN:
Excess tape is NOT allow!
Cut it 1
1
FAN ASSEMBLY (4) b50 Rev. A
1 Connect the Fan
Cable (2 connector)
1400-0249
2 Cable Tie
0515-1946 (6ea)
3
Push these wires M3L6 Flat
underneath 9inlb
of chassis
1 2 3
FAN INSTALLATION b60 Rev. A
0950-4989 1 E5070-87103
2
Power Supply Caution Label
Remove Hex screw
3
and washers (2ea)
Attention!
Avoid washer from
drop into power supply
1 2 3
REMOVE HEX SCREWS b70 Rev. A
Fix gasket with 1 E5061-07003
0515-0430 at this
corner, remove it
after assembled
gasket
Note: Alignment of
the gasket
Reinsert Hex screws
2
and washers (2ea)
6inlb
1 2
INSTALL GASKET ONTO POWER SUPPLY b80 Rev. A
Connect cable
5
Previous assembly 1 (Previous Assembly)
Attention! Note:
Ensure Gasket is Small cable is route
not fold under the big cable.
2
0515-1946 (3ea)
M3L6FLAT
9inlb 3 4 0515-1946 (2ea)
M3L6FLAT
3050-2247 (2ea)
9inlb
WASHER
1 2 3 4 5
INSTALL POWER SUPPLY c10 Rev. A
5022-1190 1
1 2
INSTALL GASKET AT FRONT FRAME c20 Rev. A
21 inlb
0515-2113 (7ea)
2
M4L8 PAN
Attention! 4
Follow the sequence
for screw tightening 3
2
1
7
6
2 5
1
3 14inlb
1 0515-1382 (3ea)
1 2 M3.5L6 Flat
ATTACH FRONT FRAME c30 Rev. A
CHECK:
Left Arm Right Arm Make sure that the screws are
not protruding out. If they are,
add washers and re-tighten till
there are no protrusions at all.
1
Note: Fan side 21 inlb
Attach T-384162, Cart arm
1
ATTACH CART ARM c40 Rev. A
E5061-66651 1
ATTN:
Re-slot the A51 board for 3 times
before fasten with washers and Nut.
Re-slot x 3
2190-0054
2
Qty: 2
2950-0054
3
Qty: 2
Use T-384165 Protective Jig
5/8 Torque box
30.4 inlb
1 2 3
DISPLAY BOARD ASSEMBLY (1) c50 Rev. A
0515-0430 (2ea)
M3L6 PAN 1
1
DISPLAY BOARD ASSEMBLY (2) c60 Rev. A
E5061-66653 1
E5061-07004 2
GASKET
1 2
ATTACH GASKET TO I/O BOARD c70 Rev. A
Previous assy 1
2
0515-0430 (2ea) 9inlb
1 2 M3L6 PAN
INSTALL DISPLAY AND I/O CONTROL BOARD c80 Rev. A
1 E5061-00208
9inlb
0515-1946 (7ea) 2190-0102 (3ea)
2 3
M3L6 Flat WASHER
Use T-384165 Protective Jig
4 2950-0035 (3ea) 9/16 Torque box
1 2 3 4 NUT 30.4 inlb
INSTALL REAR COVER c90 Rev. A
ATTN:
Confirm the FAN is
E5061-62180 not block by cable
1
Tested CPU Module
3 2
0515-1946 (3ea)
2
1
M3L6 Flat
9inlb
Follow fastening sequence
1 2
INSTALL CPU MODULE (1) d10 Rev. A
E5061-01230 4 3 E5061-01235
9inlb
0515-0430
2 M3L6 PAN
0515-1946 (4ea)
5
M3L6 Flat
9inlb
1
0515-0430 (2ea)
M3L6 PAN
9inlb
1 2 3 4 5
INSTALL CPU MODULE (2) d20 Rev. A
ATTN:
Use E5061-01242.
1 Perform slot in and out lightly for 3
times to ensure no stuck issue.
1
HDD BRACKET INSERTION VERIFICATION d30 Rev. A
SSD Sub-Assembly
1 0950-5605
3 0515-2146 (4ea)
M3L4 FLAT
E5061-01242 2 3.5inlb
1 2 3
REMOVABLE SSD ASSEMBLY (1) d40 Rev. D
7124-0442
Qty 2
(Wording No = "5" at both ends) 1400-0249
5
Qty 2
1400-0249 2 3
E5061-61614 1
8121-1710 4
1 2 3 4 5
REMOVABLE SSD ASSEMBLY (2) d50 Rev. A
Slide the Sub-Assembly
1 0515-0430 (2ea)
SSD slowly into the
guided rail M3L6 PAN
9inlb
1
INSTALL REMOVABLE SSD d60 Rev. A
3 Connect SSD
Connect cables to cables to CPU
Power supply and
CPU Module
2
Note:
Small cable is route
under the big cable.
1 E5061-61634
1 2 3
CABLE CONNECTION d70 Rev. A
1) Ensure yellow color
Fix POWER SUPPLY cables isn't tied up together
with the cable tie
1400-0493 (2ea)
CABLE TIE 2) Cables must be
pushed toward PSU
1
when tie up.
1400-0493
CABLE TIE
NOTE:
Make sure wires cable are
lower than the top of PSU to
avoid being hit by cover when
1 cover up.
INSTALL CABLE TIE d80 Rev. A
Paste "1" label on both E5061-61613
2b
end of the cable Cable
7124-0438 (2ea) 7124-0439 (2ea)
1a 2a
Label + "1"-"1" Label + "2"-"2"
E5061-61613 Paste "2" label on both
1b
Cable end of the cable
Connect
3
(x4)
1 2
1 2
1 2 3
INSTALL CABLE (1) d90 Rev. A
1 E5061-61652
2 1400-1334
Steps:
1) Connect the cable to J18 port on the CPU board
2) Paste a cable clamp on the sidewall of the PSU as
the picture.
3) Clamp the cable properly and run through under the
bar properly then tie the cable with other cables
together with a cable tie 1400-0249. (refer to page f30)
1 2
INSTALL CABLE (2) e10 Rev. A
1. Check pins for any damage
1 E5063-62001 2. Make sure all gold pin were
4
covered with lubricant
Apply Lubricant to
connector of Analog module
2 6040-1413
Use jig with Q-Tip Swab
3 to distribute the Lubricant
(Note: Move up & down for 3times)
Jig: T-385245
(with Q-Tip Swab)
APPLY LUBRICANT TO A1 MODULE e15 Rev. B
Check both LED is at this location
2
(On top of connectors)
Previous assy 1
ATTN:
1. Re-slot the A1 board for 3 times
before fasten with screw.
1 2
INSTALL A1 MODULE (1) e20 Rev. A
0515-2044 (2ea)
1
M4L8 Flat
21inlb
0515-1946 (3ea)
2
M3L6 Flat
9inlb
1 2
INSTALL A1 MODULE (2) e30 Rev. A
Install Front sub-assy 1
E5063-64901
2
Connect flat cable from
Front Panel Ass'y to CPU
Module
1 2
INSTALL FRONT PANEL & CONNECT FLAT CABLE e40 Rev. A
Connect page e10 assembly
cable into front frame sub-
assembly connector 2 Clamp the cable
3 with cable clamps
Place Front frame Sub-
1
assembly to Chassis
1 2 3
CONNECT CABLE TO FRONT SUB-ASSEMBLY e50 Rev. A
0515-1382 (4ea)
M3.5L6 Flat
14inlb 1
1
INSTALL FRONT PANEL (1) e60 Rev. A
0515-1382 (3ea)
M3.5L6 Flat
14inlb 1
1
INSTALL FRONT PANEL (2) e70 Rev. A
Before
1 04191-08000
1
INSTALL GASKET e80 Rev. A
CHECK:
Remember to remove the
protective sheet before
pasting the front overlay!
2 5188-4479
2 inlbs
(1.27mm Allen Key)
Instruction:
- Tighten 2qty set-screws
- One of the set-screw must
tighten on flat surface on the
rotary knob.
Use jig (T-384166 ) to align front
overlay when pasting it to front panel
1 E5063-00201
1 2 3
ATTACH FRONT OVERLAY AND RPG KNOB e90 Rev. D
1 E5061-01219
2 0515-0430 (2 ea)
9inlb
1401-0247 (2ea) 3
1 2
INSTALL ANGLE BAR f10 Rev. A
1 Route cable along side wall first.
2 Check connection
1 2
CHECK CABLE ROUTING f20 Rev. A
1400-0249 (4 ea)
CABLE TIE 2
1 1400-0493 (1ea)
CABLE TIE
1 2 3 3 Use Air Gun to blow dust on the unit
ATTACH CABLE TIE f30 Rev. A
E5061-60007 1
0515-1402 (4ea) 2
M3.5L8 PAN
3 1401-0448 (4ea)
14inlb
1 2 3
INSTALL COVER f40 Rev. D
BACKWARD
FORWARD
1
Turn the unit 4 Rounds, 2 X Forward (2x 360 deg )
& 2 X Backward (2x360 Deg ) to determine any
loose parts inside unit.
1
CHECK FOR LOOSE PARTS f60 Rev. A
NOTE: Parts required to be kitted to complete assembly after Final Test.
5021-2840
Part Number Description Quantity
1. E5100-40002 Rear Foot 4
E5100-40002 0515-1402 2. 0515-1402 Screw 4
1460-1345
3. 1460-1345 Tilt Stand 2
4. 5021-2840 Key Lock 4
5041-9167
0515-2049 5. 5041-9167 Bottom Foot 4
6. 0515-2049 Screw 2
E5061-24001 E4400-20725
7. E4400-20725 Outer Retainer 2
E4400-00015 8. N6705-60003 Inner Handler Strap 1
N6705-60002 9. N6705-60002 Outer Handler Strap 1
10. E5061-24001 Inner Retainer 2
11. E4400-00015 Ground Spring 2
N6705-60003 12. E4400-40018 End Cap 2
13.5041-9173 Side Trim 2
E4400-40018
PART KITTING f70 Rev. A
E5063A
Front Panel Assembly
Rev.
2 E5071-01241
0950-5396 1 3
0515-0430 (2ea)
T10 M3L6 PAN
9 inlb
1 2 3
INSTALL DRIVER BRACKET a50 Rev. A
1 E5061-61653
E5061-61654 2
3
Connect
1 2 3
INSTALL WIRES a60 Rev. A
2 Previous Assembly
1400-1334
4
Qty 4
0515-1946 (2ea)
3
T10 M3L6 PAN
9 inlb
LCD Sub-assembly 1
E5061-60112
1 2 3 4
ASSEMBLE LCD SUB ASSEMBLY a70 Rev. A
Note: Wire routing condition
2 Clamp
Connect 1
1 2
INSTALL WIRE ASSY a80 Rev. A
0363-0170 2 Open to outside
17segment
17segment
Open to outside
ATTN: 1 E5063-00202
Put on Front Panel
Assembly Jig (T-384161)
1 2
INSTALL GASKET a90 Rev. A
E5061-25001
1
Align chamfered corners
01690-41901 2
E5063-66652 3
Align chamfered corners
0515-0430 (2ea)
4 M3L6 PAN
9inlb
1 2 3 4
ASSEMBLE POWER SWITCH b10 Rev. A
E5063-40001 2
Blow away dust 1
from the keypad
contact point Previous Assembly
1 2
INSTALL KEYPAD (1) b20 Rev. A
Carefully Bend the wire to
the right side. Avoid cable
being screwed on left side.
1 E5063-66652 Use Cutter to cut the joint
1
TRIM KEYBOARD b30 Rev. A
1 12
11 10
13
2 14
9
3
4 5 8
6
7
Pull 14 points of
projection pin by pliers.
1
INSTALL KEYPAD (2) b40 Rev. A
0515-0430 (9ea) 1
T10 M3L6 PAN
9 inlb
1
INSTALL KEYPAD (3) b50 Rev. A
0515-0430 (2ea)
2
T10 M3L6 PAN
9 inlb
Push sufficiently to ensure
connector is fully insert
1
E5063-66652
1 2
INSTALL USB BOARD b60 Rev. A
Connect
3
2 0515-0430 (4ea)
2
T10 M3L6 PAN
9 inlb
4
1
3
CHECK:
Remember to remove
the protective sheet
before installing the 1
LCD sub-assembly!!
LCD sub-assembly
1 2 3
INSTALL LCD SUB ASSEMBLY b70 Rev. A
2
1
Clamp (Qty 3)
Connect E5061-61627 1
1 2
CONNECT WIRE AND CLAMP IT b80 Rev. A
Route wire pass under E5061-61654 1
2 Connect
Hide the wire under
3
the PCA board
1 2 3
WIRE ASSEMBLY ROUTING b90 Rev. A
1 E5070-61699
Connect "Display End"
part of cable to the LCD
sub-assembly
1
CONNECT LCD DISPLAY CABLE (1) c10 Rev. A
ATTN:
Use pliers to flatten the
cable clamps before
torqueing the screws.
0515-5711(2ea)
2 T20 M4L4 PAN
9 inlb
Cable clamp
direction
Cable clamp
direction
1 Previous assy
1 2
TIGHTEN LCD DISPLAY CABLE c20 Rev. A
2 Connect
1 Previous assy
1 2
CONNECT LCD DISPLAY CABLE (2) c30 Rev. A
Tie both cables
E5070-61699 &
E5061-61627 together
1 1400-0249
Make sure the cables
tied are above the line.
1
TIE UP CABLES c40 Rev. A
Check all cable connections!
GOOD NO GOOD
GOOD NO GOOD GOOD NO GOOD
GOOD NO GOOD
GOOD
Connect
GOOD NO GOOD
GOOD NO GOOD NO GOOD
CABLE CONNECTION INSPECTION c50 Rev. A
Guide points
1400-1391
3
Qty 2
E5063-00603 1
2
1400-3156
Qty 2
1 2 3
ATTACH HARDWARES c60 Rev. A
3 1400-3415
Align here
Open to outside
7segment
Open to outside
7segment
4 0515-1974 (2ea) 2 Open to outside
M2.5 L4 PAN
8160-1716
5 inlb
Qty 3
25 segment
ATTN:
Make sure the gasket
hooks over the edge
of the sheet metal 1 0960-2972
1 2 3 4
INSTALL TOUCH SCREEN CTRL BOARD, GASKET & FLAT CABLE CLAMP c70 Rev. A
Insert it to the top hole
2 Pull the it out from the bottom hole
E5061-61651 1
1 2
ROUTE CABLE c80 Rev. A
1 Connect
2 Connect
1 2
CONNECT CABLE c90 Rev. A
9 inlb
0515-0430(6ea)
2
T10 M3L6 PAN
Previous assy 1
1 2
CLOSE COVER d10 Rev. A
Connect 1
1
INSTALL DISPLAY CABLE d20 Rev. A
1 2
E5061-61631 1
Connect
7
3 4
5 6
Clamp
1
INSTALL FLAT CABLE d30 Rev. A