Text preview for : RZ-30LZ50.pdf part of LG RZ-30LZ50 Service manual



Back to : RZ-30LZ50.part1.rar | Home

website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html

P U D O T A R
LCD TV SERVICE MANUAL
CHASSIS : ML-041A

MODEL : RZ-30LZ50
CAUTION

BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CONTENTS

P U D O T A R
CONTENTS .............................................................................................. 2 PRODUCT SAFETY ..................................................................................3 SPECIFICATION ........................................................................................6 TIMING CHART .......................................................................................10 ADJUSTMENT INSTRUCTION................................................................11 TROUBLE SHOOTING ............................................................................16 BLOCK DIAGRAM...................................................................................21 WIRING DIAGRAM ..................................................................................23 EXPLODED VIEW .................................................................................. 24 EXPLODED VIEW PARTS LIST ..............................................................25 REPLACEMENT PARTS LIST ............................................................... 26 SVC. SHEET ...............................................................................................

SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE

P U D O T A R
General Guidance
Before returning the receiver to the customer,
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

Leakage Current Cold Check(Antenna Cold Check)

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts.

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

X-RAY Radiation
Warning:

The source of X-RAY RADIATION in this TV receiver is the High Voltage Section and the LCD PANEL. For continued X-RAY RADIATION protection, the replacement panel must be the same type panel as specified in the Replacement Parts List.

To determine the presence of high voltage, use an accurate high impedance HV meter.

Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Adjust brightness, color, contrast controls to minimum. Measure the high voltage. The meter reading should indicate 23.5 1.5KV: 19-21 inch, 1.5KV: 14-19 inch, 26 29.0 1.5KV: 25-29 inch, 30.0 1.5KV: 32 inch If the meter indication is out of tolerance, immediate service and correction is required to prevent the possibility of premature component failure.

Leakage Current Hot Check circuit

AC Volt-meter

To Instrument's exposed METALLIC PARTS

0.15uF

Good Earth Ground such as WATER PIPE, CONDUIT etc.

1.5 Kohm/10W

SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)

P U D O T A R
2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 F to 600 F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature. (500 F to 600 F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuitboard printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature (500 F to 600 F) b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.

P U D O T A R
Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas). At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections). "Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection. Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink. 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire. At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder. Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top. 3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.

1. Application range
This specification is applied to ML-041A chassis.

P U D O T A R
2. Requirement for Test
Testing for standard of each part must be followed in below condition. (1) Temperature: 25°C ± 2°C (2) Humidity: 65% ± 10% (3) Power: Standard input voltage (AC 100-240V, 50/60Hz) (4) Measurement must be performed after heat-run more than 30min. (5) Adjusting standard for this chassis is followed a special standard.

3.General Specification(TV)
No. Item

Specification

Remark

1

Video input applicable system

1)PAL-D/K,B/G,I 2)NTSC-M

3)SECAM NTSC 4.43' 1)PAL/SECAM BG 2)PAL/SECAM DK 3)PAL I/I 4)SECAM L/L' 5)NTSC M 7)NTSC M 6)PAL-N/M

2

Receivable broadcasting system

EU/Non-EU(RZ/RT) (PAL Market)

7)NTSC Area(RM) PAL

3

RF input channel

VHF : E2 ~ E12

UHF : E21 ~ E69

CATV : S1 ~ S20 L/L' : B,C,D

HYPER : S21 ~ S41 VHF : 2 ~ 13

FRANCE NTSC

UHF : 14 ~ 69

CATV : 1 ~ 125

VHF Low : 1~M10 UHF : S23~62 750.06 mm FS

JAPAN

VHF High : 4~S22

4 5 6 7 8 9

Input voltage Picture size

AC 100 - 240V/ 50Hz,60HZ FVS 100 program

30"

Tuning system

PAL, 200PR.(Option) NTSC

Operting environment Storage environment Display

1)Temp : 0 ~ 40 deg 2)Humidity : 85% 4)Humidity : 85% LCD Module

3)Temp : -20 ~ 60 deg

LPL, AUO, CMO

5.General Specification(Monitor)
No. 1 2 3 Panel Frequency range Control function Item Specification 30" TFT WXGA LCD H:31 ~ 61KHz, V: 56 ~ 75Hz 1) Contrast/ Brightness 2) H- Position/ V-Position 4) Auto Configure 5) Reset 1: Y 3: Pb 5: Pr DVI-I input Unit Remark

P U D O T A R
3) Tracking : Clock/Phase 4 Component Jack Middle east 7: Line1 Ready 9: LINE2 11: LINE3 /NTSC Only 13: Line3 Ready 2: Y GND D4 Jack 4: Pb GND 6: Pr GND 8: LINE1 (525i,525p,750p,1125i) Japan only 10: Line2 Ready 14: SWITCH H/V-Sync ON/ON OFF/ON ON/OFF 12: SWITCH GND Video OFF OFF LPL Power consumption Max 170 3.0 typ.30 LED Red *. 5 Power ON Stand by Active W W W W Red dimmed Red dimmed DPMS Mode Power off Type Size 697.8 x 431.8 x 50.9 683.6 x 431.8 x 41.6 683.6 x 433.6 x 43.5 0.1675 x 0.5025 x RGB 0.1675 x 0.5025 x RGB AUO LPL mm (H) x (V) x (D) 6 LCD Module CMO AUO Pixel Pitch mm Pixel Format Coating 0.16755 x 0.5025 x RGB CMO 1280 horiz. By 768 vert. pixels RGB strip arrangement Hard coating(3H), Anti-glare LPL 16EEFL treatment of the front polarizer AUO 16CCFL 16CCFL Back Light CMO

6.Optical Feature(LCD Module)
No. Item Specification LPL 1 2 3 4 Viewing Angle Luminance R/L, U/D Luminance(cd/ ) Variation WHITE RED 170,170 500 1.3 350 AUO 170,170 600 600 CMO 170,170 500 500 Typical Remark

P U D O T A R
MAX/MIN LPL Contrast Ratio ALL white/All back CIE Color Coordinates WX Wr Yr Xg Yg Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. 0.284 0.295 0.631 0.339 0.282 0.597 0.144 0.076 0.285 0.293 0.289 0.303 0.635 0.335 0.280 0.603 0.147 0.076 WY Green Blue Xb Yb

7.Feature and Function
No.

Item

Specification

Remark

1 2 3 4 5 6 7 8 9

Teletext

TOP, FLOF, LIST 10 page NEC code 1 1 2

Top(option) PAL/NTSC Side

REMOCON AV input S-AV input

Rear(RT/RM)

Component input

Side, Rear(RT/RM) Rear(RZ) Rear(RZ) DVI

PERI TV connector PERI TV connector RGB input RS-232

Half SCART: 1 Full SCART: 1 1 1 1 1

D-Sub 9 pin(RM) (RM) Stereo

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

Discrete IR

D-sub audio input 2 Carrier stereo NICAM stereo 2 Carrier dual NICAM dual

BG,DK BG,DK X X X

BG,I,LL' BG,I,LL'

DW(Double Window) mode MW(Multi Window) mode Film mode Noise reduction

O O O X X X

Progressive scan Motion detection SRS WOW EZ-pip Swivel Speaker Local Key

Pr+/-, vol+/-, ok, menu, tv/av, power

8.Component Video Input(Y, PB, PR)
NO 1 2 3 4 5 6 7 8 9 Resoluton 640 x 480 640 x 480 704 x 480 720 x 576 720 x 576 H-freq(kHz) 15.73 15.63 31.47 31.25 45.00 44.96 31.25 33.75 33.72 15.625 V-freqHz) 60.00 59.94 59.94 50.00 50.00 60.00 59.94 50.00 60.00 59.94 Pixel clock SDTV. DVD 480i SDTV. DVD 480i EDTV 480p SDTV. DVD 625 Line HDTV 576p HDTV 720p HDTV 720p Proposed RZ, RT, RM RZ, RT, RM RT, RM RT, RM RT, RM RT, RM RT, RM RT, RM RT, RM RZ, RT, RM

P U D O T A R
1280 x 720 1280 x 720 1920 x 1080 1920 x 1080 1920 x 1080 HDTV 1080i 50Hz(For Australia) HDTV 1080i 60Hz(ATSC) HDTV 1080i 59.94Hz 10

9.PC Input Mode
NO 1 2 3 4 5 6 7 8 9

Resoluton 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600

H-freq(kHz) 31.469 35 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 47.693

V-freq(Hz) 59.94 67 75.00 56.25 60.31 72.18 75.00 60.00 70.06 75.02 60.00

Pixel clock(MHz) 25.17 30.24 31.50 36.00 40.00 50.00 49.50 65.00 75.00 78.75

Proposed

DVI-PC, Analog RGB

VESA(VGA) VESA(VGA) VESA(VGA)

VESA(SVGA) VESA(SVGA) VESA(SVGA) VESA(SVGA) VESA(XGA) VESA(XGA) VESA(XGA)

1024 x 768 1024 x 768 1024 x 768 1280 x 768

10 11

80.125

VESA(WXGA)

TIMING CHART
VIDEO
A

P U D O T A R
E D

SYNC

B

C

<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> Mode
H/V Sort
Sync Polarity

Dot Clock

Frequency

Total Period Video Active Time (E) (A)

Front Porch (B)

Sync Duration (D)

Back Porch (F)

Resolution

1 2 3 4 5 6 7 8 9

H V

+ ­ ­

25.175 30.240 31.5 36

31.469 59.94 35

800

640

16

96 2

48

525

480

10

33

640x480 640x480 640x480 800x600 800x600 800x600 800x600

H

864

640

64

64

96

V H V V H

+ ­ ­ ­ ­

66.667 37.5 75

525 840 500 625

480 640 480 600 800

3 16 1 1

3 64 3 2

39 120 16 22 88 64

35.156 56.25

1024

24

72

128

H V V H H V V H H V H V

+ +

+ +

40.0 50.0 49.5 65.0 75

37.879 60.317 48.077 72.188 46.875 75.0 48.363 60.004 56.476 70.069 60.023

1056 628 666 625 806 1040 1056 1344 1328 806 1312 800

800 600 800 600 800 600 768

40 1 56 37 16 1 3 24 24 3 16 1

128 4 6 3 6 120 80

23 23

+/­ +/­ ­ ­

160 21 29 160 144 29 176 28

1024 1024 768 1024 768

136 136 6 96 3

1024x768 1024x768 1024x768 1280x768

+ + + ­

10 11

78.75 79.50

75.029 47.776

H V

+ ­

1664 798

1280 768

64 3

128 7

192 20

59.870

ADJUSTMENT INSTRUCTION
1. Application Object
This instruction is for the application to the LCD TV.

2.2.1 EDID DATA [DDC DATA Analog]
00 00 0C 10 01 37 3C 5A 00 01 02 03 04 05 06 07 08 09 FF FF FF FF FF FF 00 1E 6D 0E 01 03 18 46 2B 78 EE E8 48 4B AB 8C 00 45 4F 61 4F 01 01 01 01 01 40 1F 00 90 00 BC AE 21 00 00 1C 00 00 0A 00 0A 20 20 20 20 20 20 33 30 4C 5A 35 30 0A 20 20 0A 20 20 20 20 20 20 20 20 0A 39 AA 81 51 00 00 20 20 0B 75 A1 CF 00 FD 00 20 20 0C 01 57 01 1B 00 00 00 20 0D 01 49 01 30 32 FC 00 20 0E 01 9C 01 40 4B 00 00 00 0F 01 25 01 88 1F 52 FC B0

P U D O T A R
2. Adjustment
2.1 Auto Gain/Offset adjustment
2.1.1 Adjustment preparation
1) Conduct Heat Run with the White Pattern for more than 30 minutes. 2) Connect the signals of Pattern Generator to DVI-I Jack of LCD TV.
00 10 20 30 40 50 60 70

[DDC DATA Digital]
00 00 0C 10 81 37 3C 5A 00

2.1.2 Auto Gain/Offset adjustment

1) Use the Pattern Generator (801GF, VG819) to authorize XGA (1024 X 768) for resolution and 16 gray scale signals for patterns. Or authorize 16 gray scale (11 gray scale) signals in accordance with VG819. 2) Press the IN-START Key to convert to the adjustment mode using the adjustment (SVC) remote controller, and press VOL+ Key at the AutoGain menu. 3) Once the adjustment is completed, press the Enter Key to save and finish the adjustment

00 10 20 30 40 50 60 70

01 02 03 04 05 06 07 08 09 FF FF FF FF FF FF 00 1E 6D 0E 01 03 98 46 2B 96 EE E8 48 4B BF EE 00 31 40 3B CA CF 01 01 01 01 40 1F 00 90 00 BC AE 21 00 00 1C 00 00 0A 00 0A 20 20 20 20 20 20 33 30 4C 5A 35 30 0A 20 20 0A 20 20 20 20 20 20 20 20

0A 3A AA 45 51 00 00 20 20

0B 75 A1 40 00 FD 00 20 20

0C 01 57 61 1B 00 00 00 20

0D 01 49 40 30 32 FC 00 20

0E 01 9C 81 40 4B 00 00 00

0F 01 25 C0 88 1F 52 FC 08

2.2 EDID (The Extended Display Identification Data) setting

1) Connect D-Sub to DVI-I Cable with DVI-I Jack. 2) Set the input mode of the Set to PC. 3) Select the OPT3 from the OSD menu and set Analog or Digital for DDC data selection. 4) Select Analog for analog data, and Digital for digital data. 5) Connect the DDC automation equipment and write the DDC data.

3. Shipping Conditions
NO
1 2 3 5 8 9 Power Volume Level Main Pcture Input Mute ARC Main Last Channel

ITEM
Off 30 TV Pr 01 Off 16:9

CONDITION

REMARK

P U D O T A R
10 Station Auto Program Program Edit PSM Manual Program Favorite Program Dynamic None 80 40 70 70 0 11 Picture Dynamic Contrast Colour Tint Brightness Sharpness NTSC OPTION 14 Sound SSM AVL Flat Off 0 TV Balance Input 15 Special Child Lock Language Off Off Auto sleep H-Position V-Position Clock Phase English(Area Management) Variable by each mode 16 PC Auto Configure

*Option(PAL)
NO
1 2 3 4 5 6 7 8

ITEM
Side AV SCART PC

CONDITION Option 1
1 1 1 1 1 0 1 1

REMARK
0: Side AV Off 0: SCART Off 0: PC Off

NO
1

ITEM
Language

CONDITION Option 3
1

REMARK
0: Eng Only 1: EU5

P U D O T A R
1: Side AV On 1: SCART On 1: PC On 2: 12 nations(Europe) 3: Eng + Chines 5: Eng + FARSI 0: WEST EU 1: EAST EU 1 2: TURKY EU 3: EAST EU 2 4: Eng + Arab + Urdu SideComp 16:9 0: SideComp Off 0: Wide Off 2 Txt Lang 0 1: SideComp On 1: Wide On 200PR Text 0: 100 Program 1: 200 Program 0: Text Off 1: Text On 4: CYRILLIC 1 5: CYRILLIC 2 6: CYRILLIC 3 7: TURKY GRE 1 ACMS 0: ACMS On 1: ACMS Off 0: HiDev Off 0: Hotel Off 0: Top Off 8: TURKY GRE 2 9: TURKY GRE 3 10: ARAB FRAN 11: ARAB ENG

Option 2
0 0 1 1 0 0

1 2 3 4 5 6

HiDev Hotel Top

1: HiDev On 1: Hotel On 1: Top On

12: ARAB HEB 1 13: ARAB HEB 2 14: FARSI ENG

15: FARSI FRA 16: FARI ALL reserved

I II SAVE

0: Ch. Sound Non Memory 1: Ch. Sound Memory

3 4

Inch opt DDCi

0

Analog

Analog: Analog Digital: Digital

Turbo Vol Ch/Aus

0: except below area(Off) 0: except below area(Off) 1: China, Australia On

1: Middle-east Area Vol On

EDID ADJUSTMENT
Windows EDID V1.0 User Manual Operating System: MS Windows 98, 2000, XP Port Setup: Windows 98 => Don't need setup Windows 2000, XP => Need to Port Setup. This program is available to LCD Monitor only. 1. Port Setup a) Copy "UserPort.sys" file to "c:\WINNT\system32\drivers" folder b) Run Userport.exe 2. EDID Read & Write 1) Run WinEDID.exe

P U D O T A R
2) Edit Week of Manufacture, Year of Manufacture, Serial Number a) Input User Info Data b) Click "Update" button c) Click " Write" button c) Remove all default number d) Add 300-3FF e) Click Start button. f) Click Exit button.
Y L PR R
AUDIO COMPONENT DVD IN(480i/576i)

PB

S-VIDEO

A

9

6

Video Signal Generator

IBM Compatible PC

15 10 5

11 6 1

5

1

C

us ed

PARALLEL PORT
5V

13

1

25

14

No t

C

RS 2

OFF

ON

32

Control Line

PA

RA L

C

LE

F

L

5V

Power inlet (required)

220

PO

S

WE

VG

NIT

OR

V-S YN C

A

MO

Power Select Switch (110V/220V) Power LED

ON

5V

4.7K 4.7K

E

R

ST

OFF

4.7K

74LS06

74LS06

B

E ST Switch

B

F V-Sync On/Off Switch (Switch must be ON.)

Figure 1. Cable Connection

SVC REMOCON
1 2
To turn the TV on or off To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function. MUTE To check TV screen image easily. P-CHECK To check TV screen sound easily S-CHECK To select size of the main screen (Normal, Spectacle, Wide or Zoom) ARC Switch to closed caption broadcasting CAPTION To toggle on/off the teletext mode TXT To select an external input for the TV screen TV/AV To start turbo sound TURBO SOUND TURBO PICTURE To start turbo picture To enter adjustment mode when manufacturing the TV sets. To adjust the screen voltage (automatic): In-start mute Adjust AV(Enter into W/B adjustment mode) IN-START W/B adjustment (automatic): After adjusting the screen W/B adjustment Exit two times (Adjustment completed) To enter into the adjustment mode. To adjust horizontal line and sub-brightness. ADJ To select the multiple sound mode (Mono, Stereo or Foreign language) MPX To release the adjustment mode EXIT To easily adjust the screen according to surrounding brightness APC(PSM) To easily adjust sound according to the program type ASC(SSM) To check component input MULTIMIDIA To check the front AV FRONT-AV To move channel up/down or to select a function displayed on the screen. CH To adjust the volume or accurately control a specific function. VOL To set a specific function or complete setting. ENTER To set a function that will automatically adjust screen status to match EYE the surrounding brightness so natural color can be displayed. To select the functions such as video, voice, function or channel. MENU To set the delivery condition status after manufacturing the TV set. IN-STOP Displays the telext time in the normal mode. TIME Enables to select the sub code in the telext mode Used as Mode in the teletext mode MODE To manually select the channel. 0~9

POWER

P U D O T A R
3 4 5 6 7 8 9 10 11
Shortcut keys Shortcut keys Shortcut keys

12

Use the AV key to enter the screen W/B adjustment mode.

13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Shortcut keys Shortcut keys

TROUBLESHOOTING

P U D O T A R
No power (LED indicator off)

:[A]Process

Check 24V or 12V of Power B/D

Faill

Check short of main B/D or Change Power B/D

Pass

Check Output of L3, L1300

Change L3, L1300

Faill

Pass

Check Output of IC1300, IC4 or IC8

Change IC1300,IC4 or IC8

Faill

Faill

Change L808,L809 (F801,F802)

Pass

Check LED Assy

Change LED Assy

Faill

Pass

Check P101 Connector

No Raster

:[B]Process

P U D O T A R
Check LED Status on display unit Repeat A PROCESS Faill Check L900,L901 L902,L903 Faill Change L900,L901, L902,L903 Pass Check the input/ Output of IC901 Change IC901 Faill Pass Check inverter Connector or inverter Faill Change inverter connector or inverter Pass Check panel link Cable or module Faill Change panel link cable or module Pass Check input source cable and jack Faill Change module\

No Raster on Component signal

P U D O T A R
Repeat [A] Process Pass Check the signal of Q310,Q315,Q316 Faill Change Q310,Q315,Q316 Pass Check the input/ output of IC1 Faill Re-soldering or Change the defect part Check the input/output of IC500, IC600 Faill Re-soldering or Change the defect part Pass Check the input/ output of IC901 Faill Re-soldering or Change the defect part Pass Check input source cable and jack

No Raster on AV Signa (Video1,Video2, S-Video)

No Raster on TV(RF) signal

P U D O T A R
Repeat [A] Process Faill Check the output of TU1000 Faill Check 5V, 33V of TU1000 Re-soldering or Change the defect part Pass Check the signal of C316,C317,Q308,Q313 Faill Change C316,C317, Q308,Q313 Pass Check the input/output of IC1 Faill Re-soldering or Change the defect part Pass Check the input/output of IC500, IC600 Faill Re-soldering or Change the defect part Pass Check the input/output of IC901 Faill Re-soldering or Change the defect part Pass Check input source cable and jack

No Sound

P U D O T A R
Check the input source Faill Change source input Pass Check the input/output of IC1 Pass Faill Re-soldering or Change the defect part Check the input/output of IC100,IC101 Faill Re-soldering or Change the defect part Pass Check the speaker Faill Change speaker Pass Check the speaker wire

DVI

DVI

8

PC_R,G,B

PC_R,G,B 3

M52758 S/W (IC850)

R,G,B 3

R,G,B

3

PAL _ IF

SCART1_V

R

R,G,B

R,G,B

G

8

SCART2_V

3

SM5301 (IC800)

3

SC_R,G,B,FB 8

MST9883 ADC (IC600)

B

8

FLI2300 (IC500)

GM5221 SCALER (IC901)

LVDS or TTL OUT

SIDE_COMP

SIDE_Y,C

VCT49xyI VCTI (IC1)

BLOCK DIAGRAM

SCART1_L,R

L

RAM (IC501)

SIDE_ L,R

R

MPS7720 AMP

(IC100, IC101)

SCART2_ L,R

ROM (IC900)

(IC200)

P U D O T A R
VOUT_1,2

LA7222C

PC_ LR

BLOCK DIAGRAM DESCRIPTION
1. Video controller unit and display data conversion unit The video controller unit receives the video signal inputted to the tuner, AV port (AV1, AV2, S-Video and component) and converts it to the analog RGB signal through the microcomputer (VCTI) combined with the video decoder that integrates various functions in one chip. Then, it is inputted to the AD converter (AD9883) and generates the 4:4:4 format digital signal. This digital signal is inputted to the picture enhancer (FLI2300), which processes the video signal and converts the image quality enhanced data to an analog RGB signal again before displaying it. The image quality enhanced de-interlace signal is inputted to the scaler (GM5221) and converted to the LVDS signal by the integrated LVDS IC before being sent to the LCD module. VCTI is the main microcomputer that processes both video signals and sound signals. It also processes the RF signal received from the tuner. The scaler enables to adjust timing on the LCD panel, as well as an adjustment of the size and position of the input signal.

P U D O T A R
The graphic controller unit receives the PC (analog RGB) input and the DVI-D (digital signal), and sends the PC input to the scaler analog port and DVI-D input to the digital port. The scaler receives two inputs and converts them to the LVDS signal before sending to the module. 2. Power unit The power unit supplies 33V, 24V and 12V DC power to the main board. 33V DC power is used for the tuner, whereas 24V DC power is directly used by the inverter and the sound amplifier IC. 24V DC power is also used to generate 5V through the regulator. 12V DC power is used for the LCD panel. 5V DC is converted to 3.3V and 1.8V through the regulator, which supplies the necessary power to various ICs, such as VCTI, scaler, FLI2300 and AD9883.

WIRING DIAGRAM

4

12Pin

Wiring Part List
No. Part No. 1 6631T11020C -LPL,AUO 6631T11020D -CMO 2 6631T20032B

P812

P809

5 10Pin P750

P105

P810

P1100

P106

P202

12Pin 3

P101

8

14Pin

3

6631T20032C 4 6631T25019K 5 6631T20033F
CN5

1

2

12Pin

CN2

6

6631T20033C 7 6631T20033A
CN4

P802

CN1

8

6631T20033E 9 6631T20033D

7

6Pin

POWER BOARD

MAIN BOARD

3Pin 9

6

5Pin

P U D O T A R

P1602

P1601

EXPLODED VIEW

11

1

6

12

13

14

10

5

2

15

16

8

9

3

7

P U D O T A R
4

EXPLODED VIEW PARTS LIST
No. 1 PART NO. 3091TKE014A DESCRIPTION CABINET ASSEMBLY, RZ-30LZ50 BRAND 3090TKE007A NONE LPL

P U D O T A R
3091TKE014C CABINET ASSEMBLY, RZ-30LZ50 BRAND 3090TKE007 CMO MODULE CABINET ASSEMBLY, RZ-30LZ50 BRAND 3090TKE007 CMO,C/SKD CABINET ASSEMBLY, RZ-30LZ50 BRAND 3090TKE007 AUO 3091TKE014G 3091TKE014F 3091TKE014H 3091TKE014B CABINET ASSEMBLY, RZ-30LZ50 BRAND 3090TKE007 AUO C/SKD CABINET ASSEMBLY, RZ-30LZ50 BRAND 3090TKE007A LGEWA C/SKD 2 6304FLP122A LCD(LIQUID CRYSTAL DISPLAY), LC300W02-A5 LG PHILPS TFT COLOR EEFL,WXGA,450NITS,LVDS LCD(LIQUID CRYSTAL DISPLAY) V296W1-L06 CHIMEI TFT COLOR WXGA LVDS 6304FCI006A 6304FAU015A LCD(LIQUID CRYSTAL DISPLAY),T296XW01 AU TFT COLOR XGA LVDS 600NITD 16MS MVA 3 3809TKE014G 3809TKE014A 3809TKE014B BACK COVER ASSEMBLY, RZ-30LZ50 3809TKE006 CIS BACK COVER ASSEMBLY, RZ-30LZ50 3808TKE006A NONE BACK COVER ASSEMBLY, RZ-30LZ50 3808TKE006A LGEWA C/SKD BACK COVER ASSEMBLY, RZ-30LZ50 3808TKE006 C/SKD 3809TKE014D 3809TKE014E BACK COVER ASSEMBLY, RZ-30LZ50 3808TKE006 C/SKD CIS TILT SWIVEL ASSEMBLY, RZ-30LZ50 NONE NONE 4 3043TKK172A 3043TKK172B TILT SWIVEL ASSEMBLY, RZ-30LZ50 LGEWA C/SKD 5 6 7 8 6401TZZ042C SPEAKER ASSEMBLY, RZ-30LZ50 5WX2EA,8OHM,ESTEC(L),5P,UL1185#24, SPEAKER ASSEMBLY, RZ-30LZ50 5WX2EA,8OHM,ESTEC(R),4P,UL1185#24 6401TZZ042D 6871TST589A 6871TST642A PWB(PCB) ASSEMBLY,SUB, 26LZ50 KEY SUB TOTAL BRAND KEY BOARD PWB(PCB) ASSEMBLY,SUB, 30LZ50 LED & P/SW TOTAL BRAND . 10 11 6871TVT370A PWB(PCB) ASSEMBLY,VIDEO, RZ-30LZ50 SIDE A/V SUB TOTAL BRAND . METAL ASSEMBLY, FRAME RZ-30LZ50 LPL 4951TKS157A 4951TKS157C 4951TKS157D 4951TKS157B 6871TPT275A METAL ASSEMBLY, FRAME RZ-30LZ50 AUO METAL ASSEMBLY, FRAME CMO METAL ASSEMBLY, FRAME RZ-30LZ50 C/SKD 12 PWB(PCB) ASSEMBLY,POWER, RZ-30LZ50 POWER TOTAL BRAND ML-041A, 23",26",27",30",32" AUTOBAN LPL, AUO 6871TPT275C 3313TP3003A PWB(PCB) ASSEMBLY,POWER, RZ-30LZ50 POWER TOTAL BRAND CMO NON D/D 13 MAIN TOTAL ASSEMBLY, RZ-30LZ50 LPL BRAND ML-041A 3313TP3005A 3313TP3004A MAIN TOTAL ASSEMBLY, RZ-30LZ50 CMO BRAND ML-041A MAIN TOTAL ASSEMBLY, RZ-30LZ50 AUO BRAND ML-041A METAL ASSEMBLY, REAR RZ-30LZ50 14 4951TKK169B 4951TKK169E METAL ASSEMBLY, REAR RZ-30LZ50 LGEWA C/SKD COVER ASSEMBLY, RZ-30LZ50 REAR NON AV 15 3551TKK516A 3551TKK516B COVER ASSEMBLY, RZ-30LZ50 REAR NON AV C/SKD COVER, RZ-30LZ50 REAR AV 16 3550TKK519A 3550TKK519B COVER, RZ-30LZ50 REAR C/SKD

REPLACEMENT PARTS LIST

P U D O T A R
*S *AL LOC. NO. PART NO. DATE: 2004. 4.20. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. C757 C758 C83 C86 C924 C925 C129 C130 C10 C1001 C1002 C1003 C1004 C1007 C1010 C107 C109 C11 C110 C113 C114 C115 C116 C117 C118 C12 C125 C126 C127 C128 C1300 C1301 C1302 C1305 C1306 C1307 C135 C136 C15 C16 C18 C19 C23 C25 C26 C27 C28 C29 C3 C30 C306 C31 C318 C32 PART NO. DATE: 2004. 4. 20. DESCRIPTION / SPECIFICATION

For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;

CC, CX, CK, CN, CH : Ceramic CQ : Polyestor CE : Electrolytic CF : Fixed Film

RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RH : CHIP, Metal Glazed(Chip) RR : Drawing

CAPACITOR
C108 C1100 C1102 C1112 C1113 C1114 C1115 C119 C120 C1200 C1202 C123 C124 C1299 C1304 C131 C132 C133 C134 C404 C13 C1303 C1308 C14 C2 C20 C200 C237 C238 C319 C321 C324 C326 C327 C328 C329 C331 C333 C336 C338 C339 C340 C341 C43 C46 C50 C515 C516 C53 C59 C701 C702 C74 C755 C756

0CE476EK638 0CE106BF618 0CE107CK638 0CE108EF630 0CE108EF630 0CE108EF630 0CE108EF630 0CE106BF618 0CE106BF618 0CE477EF638 0CE477EJ630 0CE477EJ630 0CE477EJ630 0CE477EJ630 0CE477EJ630 0CE477EJ630 0CE477EJ630 0CE477EJ630 0CE477EJ630 0CE227EJ638 0CH6102K406 0CH6101K416 0CH6101K416 0CH6102K406 0CH6102K406 0CH6102K406 0CH6221K416 0CH6102K406 0CH6102K406 0CH6120K416 0CH6120K416 0CH6120K416 0CH6120K416 0CH6120K416 0CH6120K416 0CH6120K416 0CH6150K416 0CH6150K416 0CH6150K416 0CH6150K416 0CH6150K416 0CH6150K416 0CH6150K416 0CH6102K406 0CH6102K406 0CH6102K406 0CH6330K416 0CH6330K416 0CH6102K406 0CH6102K406 0CH6120K416 0CH6120K416 0CH6102K406 0CH6471K416 0CH6471K416

47UF KMG 50V M FM5 TP 5 10UF KME 16V M FL TP5 "100UF SHL,SD 50V M FM5 TP 5" 1000UF KMG 16V M FM5 BULK 1000UF KMG 16V M FM5 BULK 1000UF KMG 16V M FM5 BULK 1000UF KMG 16V M FM5 BULK 10UF KME 16V M FL TP5 10UF KME 16V M FL TP5 470UF KMG 16V M FM5 TP 5 470UF KMG 35V M FM5 BULK 470UF KMG 35V M FM5 BULK 470UF KMG 35V M FM5 BULK 470UF KMG 35V M FM5 BULK 470UF KMG 35V M FM5 BULK 470UF KMG 35V M FM5 BULK 470UF KMG 35V M FM5 BULK 470UF KMG 35V M FM5 BULK 470UF KMG 35V M FM5 BULK 220UF KMG 35V M FM5 TP 5 1000PF 50V J SL 2012 R/TP 100PF 50V J NP0 2012 R/TP 100PF 50V J NP0 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 220PF 50V J NP0 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 12PF 50V J NP0 2012 R/TP 12PF 50V J NP0 2012 R/TP 12PF 50V J NP0 2012 R/TP 12PF 50V J NP0 2012 R/TP 12PF 50V J NP0 2012 R/TP 12PF 50V J NP0 2012 R/TP 12PF 50V J NP0 2012 R/TP 15PF 50V J NP0 2012 R/TP 15PF 50V J NP0 2012 R/TP 15PF 50V J NP0 2012 R/TP 15PF 50V J NP0 2012 R/TP 15PF 50V J NP0 2012 R/TP 15PF 50V J NP0 2012 R/TP 15PF 50V J NP0 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 33PF 50V J NP0 2012 R/TP 33PF 50V J NP0 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 12PF 50V J NP0 2012 R/TP 12PF 50V J NP0 2012 R/TP 1000PF 50V J SL 2012 R/TP 470F 50V J NP0 2012 R/TP 470F 50V J NP0 2012 R/TP

0CH6471K416 0CH6101K416 0CH6102K406 0CH6102K406 0CH6050K116 0CH6050K116 181-007F 181-007F 0CK104CK56A 0CH3103K516 0CH3103K516 0CH3103K516 0CH3103K516 0CH3103K516 0CK273DK51A 0CK225DFK4A 0CH3103K516 0CH3104K566 0CH3103K516 0CK225DFK4A 0CK225DFK4A 0CK104CK56A 0CK562CK51A 0CK562CK51A 0CK104CK56A 0CH3104K566 0CK105EK56A 0CK105EK56A 0CH3104K566 0CH3104K566 0CH3104K566 0CK103CK51A 0CH3103K516 0CH3104K566 0CK103CK51A 0CH3103K516 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK106EF56A 0CH3104K566 0CH3104K566 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK334CF94A 0CK104CK56A 0CH3104K566 0CK334CF94A 0CH3104K566 0CK104CK56A 0CH3104K566 0CK334CF94A

470F 50V J NP0 2012 R/TP 100PF 50V J NP0 2012 R/TP 1000PF 50V J SL 2012 R/TP 1000PF 50V J SL 2012 R/TP 5PF 50V D NP0 2012 R/TP 5PF 50V D NP0 2012 R/TP "MPE ECQ-V1H224JL3(TR), 50V 0" "MPE ECQ-V1H224JL3(TR), 50V 0" 0.1UF 1608 50V 10% R/TP X7R 10000PF 50V 10% B(Y5P) 2012 10000PF 50V 10% B(Y5P) 2012 10000PF 50V 10% B(Y5P) 2012 10000PF 50V 10% B(Y5P) 2012 10000PF 50V 10% B(Y5P) 2012 27000PF 2012 50V 10% B(Y5P) "2.2UF 2012 16V 20%,-20% F(Y5" 10000PF 50V 10% B(Y5P) 2012 0.1UF 50V 10% X7R 2012 R/TP 10000PF 50V 10% B(Y5P) 2012 "2.2UF 2012 16V 20%,-20% F(Y5" "2.2UF 2012 16V 20%,-20% F(Y5" 0.1UF 1608 50V 10% R/TP X7R 5600PF 1608 50V 10% R/TP B(Y 5600PF 1608 50V 10% R/TP B(Y 0.1UF 1608 50V 10% R/TP X7R 0.1UF 50V 10% X7R 2012 R/TP 1UF 3216 50V 10% X7R R/TP 1UF 3216 50V 10% X7R R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.01UF 1608 50V 10% R/TP B(Y 10000PF 50V 10% B(Y5P) 2012 0.1UF 50V 10% X7R 2012 R/TP 0.01UF 1608 50V 10% R/TP B(Y 10000PF 50V 10% B(Y5P) 2012 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 10UF 3216 16V 10% X7R R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R "0.33UF 1608 16V 80%,-20% F(Y" 0.1UF 1608 50V 10% R/TP X7R 0.1UF 50V 10% X7R 2012 R/TP "0.33UF 1608 16V 80%,-20% F(Y" 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 1608 50V 10% R/TP X7R 0.1UF 50V 10% X7R 2012 R/TP "0.33UF 1608 16V 80%,-20% F(Y"

*S *AL LOC. NO. C33 C34 C35 C36 C37 C38 C39 C4 C40 C41 C42 C44 C45 C49 C500 C504 C505 C506 C507 C508 C509 C51 C510 C511 C512 C513 C514 C517 C518 C519 C521 C522 C523 C524 C526 C527 C528 C529 C530 C531 C532 C533 C534 C535 C536 C537 C538 C539 C540 C541 C542 C544 C545 C546 C547 C549 C550 C551 C552 C553 C554 C555

PART NO. 0CK334CF94A 0CK104CK56A 0CK334CF94A 0CK104CK56A 0CK334CF94A 0CK104CK56A 0CK104CK56A 0CH3104K566 0CK104CK56A 0CK104CK56A 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK104CK56A 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK104CK56A 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566

DATE: 2004. 4. 20. DESCRIPTION / SPECIFICATION "0.33UF 1608 16V 80%,-20% F(Y" 0.1UF 1608 50V 10% R/TP X7R "0.33UF 1608 16V 80%,-20% F(Y" 0.1UF 1608 50V 10% R/TP X7R "0.33UF 1608 16V 80%,-20% F(Y" 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 1608 50V 10% R/TP X7R 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 1608 50V 10% R/TP X7R 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP

*S *AL LOC. NO. C556 C557 C558 C559 C567 C6 C60 C606 C608 C609 C61 C611 C612 C613 C614 C615 C616 C618 C619 C620 C621 C622 C623 C624 C625 C626 C627 C628 C629 C632 C633 C634 C635 C636 C637 C638 C639 C64 C640 C65 C66 C67 C7 C70 C700 C704 C705 C71 C72 C73 C75 C750 C751 C752 C753 C759 C76 C760 C761 C77 C78 C79

PART NO. 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK473CK56A 0CK473CK56A 0CK473CK56A 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK104CK56A 0CH3104K566 0CH3822K516 0CH3823K516 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK106EF56A 0CH3104K566 0CK104CK56A 0CK104CK56A 0CH3104K566 0CH3104K566 0CH3104K566 0CK106EF56A 0CK106EF56A 0CK106EF56A 0CH3104K566 0CK104CK56A 0CH3104K566 0CK104CK56A 0CK104CK56A 0CK104CK56A 0CK106EF56A 0CH3104K566 0CH3104K566 0CK106EF56A 0CK106EF56A 0CK106EF56A

DATE: 2004. 4. 20. DESCRIPTION / SPECIFICATION 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 47000PF 1608 50V 10% R/TP X7 47000PF 1608 50V 10% R/TP X7 47000PF 1608 50V 10% R/TP X7 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 1608 50V 10% R/TP X7R 0.1UF 50V 10% X7R 2012 R/TP 8200PF 2012 50V 10% B(Y5P) R 82000PF 2012 50V 10% B(Y5P) 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 10UF 3216 16V 10% X7R R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 10UF 3216 16V 10% X7R R/TP 10UF 3216 16V 10% X7R R/TP 10UF 3216 16V 10% X7R R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 1608 50V 10% R/TP X7R 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 0.1UF 1608 50V 10% R/TP X7R 10UF 3216 16V 10% X7R R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 10UF 3216 16V 10% X7R R/TP 10UF 3216 16V 10% X7R R/TP 10UF 3216 16V 10% X7R R/TP

P U D O T A R

*S *AL LOC. NO. C8 C80 C800 C801 C802 C803 C804 C808 C809 C81 C810 C811 C812 C813 C82 C84 C850 C851 C852 C853 C854 C855 C856 C864 C865 C866 C867 C868 C869 C870 C9 C901 C902 C903 C904 C905 C906 C907 C908 C909 C910 C911 C912 C913 C914 C915 C916 C917 C918 C919 C920 C921 C922 C923 C926 C927 C928 C929 C930 C931 C935 C936

PART NO. 0CK104CK56A 0CK106EF56A 0CK105CF94A 0CK105CF94A 0CK105CF94A 0CK105CF94A 0CH3104K566 0CK105DK94A 0CK105DK94A 0CK106EF56A 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK106EF56A 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CK104CK56A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CK103CK51A 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566

DATE: 2004. 4. 20. DESCRIPTION / SPECIFICATION 0.1UF 1608 50V 10% R/TP X7R 10UF 3216 16V 10% X7R R/TP "1UF 1608 16V 80%,-20% R/TP F" "1UF 1608 16V 80%,-20% R/TP F" "1UF 1608 16V 80%,-20% R/TP F" "1UF 1608 16V 80%,-20% R/TP F" 0.1UF 50V 10% X7R 2012 R/TP "1UF 2012 50V 80%,-20% R/TP F" "1UF 2012 50V 80%,-20% R/TP F" 10UF 3216 16V 10% X7R R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 10UF 3216 16V 10% X7R R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 1608 50V 10% R/TP X7R 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.01UF 1608 50V 10% R/TP B(Y 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP

*S *AL LOC. NO. C938 C939 C940 C941 C942 C943 C944 C945 C946 C947 C948 C949 C950 C951 C952 C958 C96 C960 C963 C969 C970 C973 C121 C122 C202 C203 C204 C205 C207 C209 C21 C210 C211 C214 C217 C218 C22 C220 C222 C223 C224 C24 C343 C345 C348 C350 C351 C352 C353 C47 C48 C501 C600 C601 C602 C603 C610 C754 C85 C100 C1006 C1008

PART NO. 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CH3104K566 0CC100CK41A 0CC100CK41A 0CC101CK41A 0CC221CK41A 0CC471CK41A 0CC471CK41A 0CC102CK41A 0CC101CK41A 0CC102CK41A 0CC101CK41A 0CC102CK41A 0CC101CK41A 0CC471CK41A 0CC471CK41A 0CC102CK41A 0CC102CK41A 0CC102CK41A 0CC101CK41A 0CC101CK41A 0CC102CK41A 0CC270CK41A 0CC270CK41A 0CC270CK41A 0CC270CK41A 0CC270CK41A 0CC270DK41A 0CC270CK41A 0CC220CK41A 0CC220CK41A 0CC101CK41A 0CC220CK41A 0CC220CK41A 0CC220CK41A 0CC220CK41A 0CC102CK41A 0CC471CK41A 0CC102CK41A 0CH8476F691 0CH8106J691 0CE227WF6DC

DATE: 2004. 4. 20. DESCRIPTION / SPECIFICATION 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 0.1UF 50V 10% X7R 2012 R/TP 10PF 1608 50V 5% R/TP NP0 10PF 1608 50V 5% R/TP NP0 100PF 1608 50V 5% R/TP NP0 220PF 1608 50V 5% R/TP NP0 470PF 1608 50V 5% R/TP NP0 470PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 100PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 100PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 100PF 1608 50V 5% R/TP NP0 470PF 1608 50V 5% R/TP NP0 470PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 100PF 1608 50V 5% R/TP NP0 100PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 27PF 1608 50V 5% R/TP NP0 27PF 1608 50V 5% R/TP NP0 27PF 1608 50V 5% R/TP NP0 27PF 1608 50V 5% R/TP NP0 27PF 1608 50V 5% R/TP NP0 27PF 2012 50V 5% NP0 R/TP 27PF 1608 50V 5% R/TP NP0 22PF 1608 50V 5% R/TP NP0 22PF 1608 50V 5% R/TP NP0 100PF 1608 50V 5% R/TP NP0 22PF 1608 50V 5% R/TP NP0 22PF 1608 50V 5% R/TP NP0 22PF 1608 50V 5% R/TP NP0 22PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 470PF 1608 50V 5% R/TP NP0 1000PF 1608 50V 5% R/TP NP0 47UF 16V 20% 105STD (CYL) R/ 10UF 35V 20% 105STD (CYL) R/ 220UF MVK 16V 20% R/TP(SMD)

P U D O T A R

*S *AL LOC. NO. C111 C112 C17 C206 C208 C219 C221 C225 C226 C227 C228 C231 C232 C235 C236 C300 C301 C302 C303 C304 C307 C308 C309 C312 C313 C314 C315 C316 C317 C5 C502 C503 C52 C520 C525 C54 C543 C55 C560 C566 C604 C605 C607 C62 C63 C703 C805 C806 C807 C814 C815 C857 C858 C859 C860 C861 C862 C863 C87 C88 C900 C953

PART NO. 0CE475EK638 0CE475EK638 0CH8106J691 0CH8226F691 0CH8226F691 0CH8226F691 0CH8226F691 0CH8106J691 0CH8106J691 0CH8106J691 0CH8106J691 0CH8106J691 0CH8106J691 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CE107WF6DC 0CH8106F691 0CH8106F691 0CH8106F691 0CH8106F691 0CH8476H691 0CH8106F691 0CH8106F691 0CH8476H691 0CH8106F691 0CH8106F691 0CH8106F691 0CH8106F691 0CE475WJ6DC 0CH8476F691 0CH8476F691 0CH8476F691 0CH8106F691 0CH8106F691 0CH8476F691 0CH8476F691 0CH8476H691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CE107WF6DC 0CE227WF6DC 0CE227WF6DC 0CE227WF6DC 0CE227WF6DC 0CH8476F691 0CE227WF6DC 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476F691 0CH8476H691 0CH8476F691 0CH8476F691

DATE: 2004. 4. 20. DESCRIPTION / SPECIFICATION 4.7UF KMG 50V 20% FM5 TP 5 4.7UF KMG 50V 20% FM5 TP 5 10UF 35V 20% 105STD (CYL) R/ 22UF 16V 20% 105STD (CYL) R/ 22UF 16V 20% 105STD (CYL) R/ 22UF 16V 20% 105STD (CYL) R/ 22UF 16V 20% 105STD (CYL) R/ 10UF 35V 20% 105STD (CYL) R/ 10UF 35V 20% 105STD (CYL) R/ 10UF 35V 20% 105STD (CYL) R/ 10UF 35V 20% 105STD (CYL) R/ 10UF 35V 20% 105STD (CYL) R/ 10UF 35V 20% 105STD (CYL) R/ 100UF MVK 16V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 100UF MVK 16V 20% R/TP(SMD) 10UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 47UF 25V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 47UF 25V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 4.7UF MVK 35V 20% R/TP(SMD) 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 10UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 25V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 100UF MVK 16V 20% R/TP(SMD) 220UF MVK 16V 20% R/TP(SMD) 220UF MVK 16V 20% R/TP(SMD) 220UF MVK 16V 20% R/TP(SMD) 220UF MVK 16V 20% R/TP(SMD) 47UF 16V 20% 105STD (CYL) R/ 220UF MVK 16V 20% R/TP(SMD) 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 25V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/

*S *AL LOC. NO. C956 C957 C959 C97 C972 C1500 C1501 C1600 C2006 C2007

PART NO. 0CH8476H691 0CH8476F691 0CH8476F691 0CH8476H691 0CH8476H691 0CN1040K949 0CN4710K519 0CN1040K949 0CN4710K519 0CN4710K519

DATE: 2004. 4. 20. DESCRIPTION / SPECIFICATION 47UF 25V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 16V 20% 105STD (CYL) R/ 47UF 25V 20% 105STD (CYL) R/ 47UF 25V 20% 105STD (CYL) R/ 0.1M 50V Z F TA52 470P 50V K B TA52 0.1M 50V Z F TA52 470P 50V K B TA52 470P 50V K B TA52

P U D O T A R
DIODEs
D100 D101 IC751 IC754 ZD1300 ZD1301 D102 D103 D107 D711 D104 D105 D700 D701 D702 D703 D704 D705 D706 ZD10 ZD1000 ZD201 ZD202 ZD203 ZD204 ZD205 ZD206 ZD207 ZD208 ZD210 ZD213 ZD214 ZD215 ZD216 ZD217 ZD218 ZD219 ZD220 ZD221 ZD851 ZD852 0DRFC00288A 0DRFC00288A 0DRSE00018A 0DRSE00018A 0DR340009AA 0DR340009AA 0DS181009AA 0DS181009AA 0DS226009AA 0DD184009AA 0DZ620009HB 0DZ620009HB 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZ910009FE 0DZ330009DF 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A 0DZRM00178A SS14 FAIR CHILD R/TP SMA 20SS14 FAIR CHILD R/TP SMA 20SRV05-4.TC SEMTECH R/TP SOT2 SRV05-4.TC SEMTECH R/TP SOT2 MBRS340 TP FAIRCHILD NON 40V MBRS340 TP FAIRCHILD NON 40V KDS181 TP KEC SOT-23 80V 3 KDS181 TP KEC SOT-23 80V 3 KDS226 TP KEC SOT-23 80V 30 KDS184 TP KEC - 85V - - - 30 UDZ S 6.2B TP ROHM SOD323 20 UDZ S 6.2B TP ROHM SOD323 20 UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS 9.1B TP ROHM - - 9.1V MTZJ33B TP ROHM-K DO34 0.5W UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM UDZS TE-17 5.1B ROHM R/TP SM

IC

IC3 C500 IC200 IC501 IC749

0IKE702700D 0IZZTSA001A 0ISA722200A 0IMMREB010A 0IMMRSG036A

"KIA7027AF 3, SOT-89 TP RESET" "RZ/RT-30""/26""/23""/27"" LZ50 F" LA7222 (1280 AUDIO) - - - "M12L64322A-6T ESMT 86P,TSOP" "M24C02-WMN6T SGS-THOMSON 8P,"

*S *AL LOC. NO. IC753 IC907 IC918 IC100 IC101 IC1300 IC1301 IC500 IC750 IC850 IC702 IC1 IC600 IC800 IC901 IC2 IC300 IC4 IC505 IC6 IC601 IC604 IC8 IC905 IC906 IC103 IC752

PART NO. 0IMMRSG036A 0IMCRAL006A 0IMCRAL006A 0IMCRMZ002A 0IMCRMZ002A 0IMCRMZ001A 0IMCRMZ001A 0IMCRGN002C 0IMCRSG010A 0IMCRMI006A 0IMO140662A 0IPRPMN003C 0IPRPM3002B 0IPRPNP001A 0IPRPGN014A 0IPMGNS001E 0IPMGKE039A 0IPMGNS001E 0IPMGSG018D 0IPMGSG018D 0IPMGNS001E 0IPMGFA061A 0IMCRFA015A 0IPMGFA061A 0IPMGSG018D 0ISS780800J 0IMCRTI001A

DATE: 2004. 4. 20. DESCRIPTION / SPECIFICATION "M24C02-WMN6T SGS-THOMSON 8P," AT24C16AN-10SI-2.7 ATMEL 8P AT24C16AN-10SI-2.7 ATMEL 8P MP7720 MONOLITHIC POWER SYST MP7720 MONOLITHIC POWER SYST MP1583DN MONOLITHIC POWER SY MP1583DN MONOLITHIC POWER SY FLI2300BD GENESIS 208P PQFP ST3232CDR SGS-THOMSON SOP16 "M52758FP MITSUBISHI 36PIN, R" "MC14066BDR2 14P,SOIC TP BILA" VCT49XYF C7(NTSC+PAL) MICRON "MST9883C-110 MSTAR 80P,LQFP" "SM5301BS(ATSC DTV) NPC 28P,H" GM5221H(HDCP) GENESIS 208P Q LM1117MPX-3.3 NATIONAL SEMIC "KIA78D09F KEC 3P,DPAK R/TP 9" LM1117MPX-3.3 NATIONAL SEMIC "LD1086DT18TR SGS-THOMSON 3P," "LD1086DT18TR SGS-THOMSON 3P," LM1117MPX-3.3 NATIONAL SEMIC "FAN1587AD33X FAIRCHILD 3P,DP" KA7805R FAIRCHILD 2P D-PAK R "FAN1587AD33X FAIRCHILD 3P,DP" "LD1086DT18TR SGS-THOMSON 3P," "KA78M08R 3P,D-PAK TP VOL. RE" SN74HCT157D TEXAS INSTRUMENT

*S *AL LOC. NO. L701 L800 L850 L900 L901 L902 L903 L907 L1500 L1600 L1700 L1 L10 L1001 L11 L12 L13 L14 L15 L16 L17 L2 L200 L201 L306 L307 L308 L309 L310 L402 L403 L7 L8 L9

PART NO. 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 0LA0102K119 0LA0102K119 0LA0102K119 0LC1032101A 0LC1032101A 0LC1020101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1032101A 0LC1020101A 0LC1020101A 0LC1532101A 0LC1532101A 0LC1532101A 0LC1532101A 0LC1532101A 0LC1532101A 0LC1532101A 0LC1032101A 0LC1032101A 0LC1032101A

DATE: 2004. 4. 20. DESCRIPTION / SPECIFICATION HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM 10UH K 2.3*3.4 TP 10UH K 2.3*3.4 TP 10UH K 2.3*3.4 TP 10UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C32161UH 10% 2012 R/TC FI-B2012-1 10UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C32161UH 10% 2012 R/TC FI-B2012-1 1UH 10% 2012 R/TC FI-B2012-1 15UH 10% 3216 R/TC FI-C321615UH 10% 3216 R/TC FI-C321615UH 10% 3216 R/TC FI-C321615UH 10% 3216 R/TC FI-C321615UH 10% 3216 R/TC FI-C321615UH 10% 3216 R/TC FI-C321615UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C321610UH 10% 3216 R/TC FI-C3216-

P U D O T A R
COIL & CORE & INDUCTOR
L104 L105 L1300 L1301 L100 L1002 L1003 L202 L203 L204 L205 L207 L208 L209 L210 L3 L301 L302 L304 L311 L4 L401 L500 L501 L502 L503 L504 L505 L600 L601 L602 L603 6140TBZ045A 6140TBZ045A 6140VR0008B 6140VR0008B 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001A 6210TCE001G 6210TCE001A 6210TCE001A 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001A "38.5UH(DIP), 6A, P7.5, DR8.3" "38.5UH(DIP), 6A, P7.5, DR8.3" SLF12575T-150M3R2 15UH SMD SLF12575T-150M3R2 15UH SMD HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HH-1M3216-501 CERATEC 3216MM HB-1S2012-080JT CERATEC 2012 HB-1S2012-080JT CERATEC 2012 HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HH-1M3216-501 CERATEC 3216MM HB-1S2012-080JT CERATEC 2012

FET & TRANSISTOR
TR1600 Q100 Q1000 Q101 Q1101 Q12 Q13 Q14 Q15 Q16 Q17 Q212 Q300 Q301 Q302 Q303 Q304 Q305 Q306 Q308 Q310 Q313 Q315 Q316 Q317

0TR127009AA 0TR387500AA 0TR388109AA 0TR150400BA 0TR387500AA 0TR150400BA 0TR150400BA 0TR150400BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR150400BA 0TR150400BA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA

KTA1270-Y(KTA562TM) TP KEC T CHIP 2SC3875S(ALY) BK KEC KTC3881 CHIP TP KEC - CHIP 2SA1504S(ASY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SA1504S(ASY) BK KEC CHIP 2SA1504S(ASY) BK KEC CHIP 2SA1504S(ASY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SA1504S(ASY) BK KEC CHIP 2SA1504S(ASY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC -

*S *AL LOC. NO. Q318 Q500 Q701 Q901 IC1101 IC902

PART NO. 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TFVI80005A 0TFVI80005A

DATE: 2004. 4. 20. DESCRIPTION / SPECIFICATION CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC CHIP 2SC3875S(ALY) BK KEC VISHAY SI4963DY R/TP SO-8 -2 VISHAY SI4963DY R/TP SO-8 -2

*S *AL LOC. NO. R312 R313 R314 R315 R322 R394 R395 R44 R45 R502 R505 R506 R520 R527 R530 R607 R610 R700 R703 R705 R712 R713 R715 R716 R719 R725 R726 R729 R730 R737 R738 R752 R753 R755 R756 R760 R761 R802 R803 R805 R806 R809 R83 R85 R850 R851 R854 R87 R89 R930 R931 R941 R960 R964 R969 R971 R978 R979 R980 R999 RA600 RA601

PART NO. 0RH4700D622 0RH1500D622 0RH4700D622 0RH1500D622 0RH1500D622 0RH6800D622 0RH6800D622 0RH1000D622 0RH1000D622 0RH3301D622 0RH0000D622 0RH0000D622 0RH1800D622 0RH4701D622 0RH0000D622 0RH1000D622 0RH2701D622 0RH0000D622 0RH4701D622 0RH4701D622 0RH0752D622 0RH0752D622 0RH1202D622 0RH0752D622 0RH1502D622 0RH1000D622 0RH0000D622 0RH1000D622 0RH1000D622 0RH4701D622 0RH4701D622 0RH0000D622 0RH0000D622 0RH0102D622 0RH0102D622 0RH0000D622 0RH0000D622 0RH8200D622 0RH0000D622 0RH0752D622 0RH4700D622 0RH0102D622 0RH1000D622 0RH1000D622 0RH4701D622 0RH4701D622 0RH0000D622 0RH1000D622 0RH1000D622 0R