Text preview for : HD781010.pdf part of Philips Senseo HD7810/10 Philips Senseo Coffee Maker



Back to : HD781010.pdf | Home

Coffee Maker Senseo HD7810/10

Philips Domestic Appliances and Personal Care

Service Manual
PRODUCT INFORMATION - This product meets the requirements regarding interference suppression on radio and TV. - After the product has been repaired, it should function properly and has to meet the safety requirements as officially laid down at this moment. TECHNICAL INFORMATION Voltage Frequency Power consumption Standby power consumption Contents reservoir Colour setting : : : : : : 220 - 230 V 50 Hz 1450 W 0.002 kWh 755 cc White / Vapour dusk
Waterlevel Sensor Temp. Sensor

L Pump M CONTROL PCB

Automatic thermostat

Boiler

N

Push buttons

Published by Philips Domestic Appliances and Personal Care

Printed in the Netherlands

© Copyright reserved

Subject to modification

04/02

DISASSEMBLY- AND RE-ASSEMBLY ADVISE Disassembly information To remove the brew chamber lid cover (item 8 exploded view) handle as follows: - Place the screwdriver on the positions (see picture 1) and lift the cover over the snap locks on both positions.

HD7810/10
Removing Brew chamber head (item 1 exploded view) handle as follows: - Back cover and 3-way valve must be disassembled! - Place the appliance such a way that you are looking at the boiler. - First remove the boiler from the snap lock position of the brew chamber. (there were the boiler is fixed to the brew chamber) - To do so use a screwdriver and bend slightly the both ribs to the outer side and pull the boiler out of the fixation point. - To remove the brew chamber, use your both thumbs (see picture 3) and push strongly with a little distortion (rotation) until the brew chamber comes loose.

picture 1 - The cover lid can now be lifted up a little and to remove the complete cover including lever and push rod (items 9 and 10) squeeze strongly with two fingers both legs of the push rod (see picture 2) to each other, so that the two pins will get out of the hinge position on the brew chamber.

picture 3 picture 2 - Reassemble follow above steps backwards. To reach the components placed on the base handle as follows: - First remove back cover, brew chamber and 3-way valve. - Remove both Torx T15 screws see exploded view in the near of position A. - Bend the 2 click snap locks with a screwdriver (see base), and the housing can now be removed. - To remove the rest of the housing unlock the last 4 snap locks at the base and gently pull of the front cover. - To reassemble follow above steps backwards. REPAIR INSTRUCTION Descaling Regular descaling will prolong the life of your appliance and will guarantee optimal brewing results for a long time. - Follow the steps in the section headed "Preparing the appliance for use" see DFU (Direction For Use manual). - In stead of only water use a mix of water and Lemon sour. - For the best result leave the mix of water and Lemon sour for about 30 minutes in the appliance, before you start with flushing the appliance. - To get the best results repeat above mentioned step once or twice. - When finished, flush the appliance twice by repeating the above mentioned steps only use water instead. OPTIONAL (accessories) - XL watertank (10 Cups) Commercial type number HD7982 Service code : 4222 259 20100

- To remove lever from lid cover, take a screwdriver and bend carefully the two lips/ribs in the lid cover outwards and push the lever with force out of the hinge. - Reassemble follow steps backwards, without using a screwdriver. To remove the back cover (item 23 exploded view) handle as follows: - Remove valve outlet. - Start at the upper side of the back cover and stick a screwdriver into the 2 snap locks positions and gently pull the back cover from the appliance so that a little chink between back cover and brew chamber becomes visible. - Put the screwdriver in to the 4 rectangular holes (snap locks) at the back and gently pull the screwdriver such away that the lips of the snap locks are bent outwards. - If all clicks positions are loose, it is possible to remove the back cover. - Reassemble follow steps backwards. Removing 3-way valve (item 13 exploded view) handle as follows: - Unsnap boiler out of brew chamber. - Rotate the 3-way valve a quarter (90°) counter clockwise. - Gently pull the 3-way valve out of the boiler. - Reassemble follow the above steps backwards.

2-4

PARTS LIST & EXPLODED VIEW

HD7810/10

1

8 2 9 10 3 4 5 11

12

6

7

Pos 1 2 3 4 5 6 7 8 9 10 11 12

Service code 4222 259 08570 4222 259 08800 4222 259 08950 4222 247 35750 4222 247 37560 4222 240 06360 4222 247 35790 4222 259 08680 4222 247 37520 4222 247 35820 4222 247 06810 4222 259 06890

Description Brewchamber assy compl. White Pad holder single Vapour dusk Pad holder double Vapour dusk Foam chamber Foam chamber cover Vapour dusk Drip tray cover Drip tray Brewchamber Lid Lever Vapour Dusk Push Rod Brew chamber radial seal Distrubutor assy 3-4

A

PARTS LIST & EXPLODED VIEW

HD7810/10

21 13

14 22 23 15

16 17 18 19 20

24

25

A

26
Pos 13 14 15 16 17 18 19 20 Service code 4222 259 01290 4222 259 03610 4222 247 35590 4222 259 11160 4222 247 06840 4222 246 16300 4222 247 35880 4222 247 06860 Description Valve (3way) Boiler assy compl. 230 V / 1450 W Boiler frame Temp. sensor Hose 0.25 metre Water level sensor Pump Elbo O-ring (elbo) Pos Service code Description Aqua blue Silent blue White White

21 4222 259 04390 Water tank assy 4222 259 20100 XL (10 Cups) Water tank assy 22 4222 247 37550 Valve outlet 23 4222 247 37540 Back cover 24 4222 247 35870 Filter 25 4222 247 06820 Water socket 26 4213 247 05250 Foot

= changed

4-4