Text preview for : Sony_KV36XBR400_Part5.PDF part of Sony KV36XBR400 Part5 Sony Sony_KV36XBR400_Part5.PDF
Back to : Sony_KV36XBR400_Part5.PDF | Home
DX1A SERVICE LIST (#7): CXA2026AS
Device Name: CXA2026AS { DQP Control / SONY } / IC5511 (D-board)
Slave Address: 8Eh
Register Control Register Data Data Data Initial Settings & [Adjusted Data]
Comment
No & Name Function & Link Type Range (32V&36V CRTs)
Full Vcomp1 Vcomp2 Full: 480p/960i (4x3) display mode
32V 36V 32V 36V 32V 36V Vcomp1: 480p/960i (16x9) display mode
0 DFON SW0: DF on/off switch C 0, 1 0 Vcomp2: 1080i (16x9) display mode
1 DQP PWM: DQP phase Adj. 0~63 29 [20] 29 [20] C: Common data
2 DF DAC1: DF phase Adj. 0~63 34 [24] 34 [24] Adj.: Adjusted data
3 DQPD H.AMP: DQP dc-level Adj. 0~63 34 [34] 34 [34]
4 QPDV U.CBOW, L.CBOW: DQP dc-level vertical modulation 0~63 51 47 U.CBOW = QPDV + DVS
5 DVS U.CBOW, L.CBOW: DQP dc-level tilt 0~(3)~7 0 0 L.CBOW = QPDV - DVS
6 QPDY U.MBH,L.MBH: DQP dc-level at top & bottom areas 0~63 7 7 ( ): Settings at center
22 17 22 17 22 17
7 DQPA DC SHIFT: DQP amplitude Adj. 0~63 Settings for 36V are used as initial settings.
-- 41 --
[22] [17] [22] [17] [22] [17]
8 QPAV U.YBOW, LYBOW: DQP amplitude vertical modulation 0~63 38 34 U.YBOW = QPAV + AVS
9 AVS U.YBOW, LYBOW: DQP amplitude tilt 0~7 3 3 L.YBOW = QPAV - AVS
10 NORM SW1: 0, 1 0 0
Copy Function 3: (Set CPY3=1, then press MUTE + Enter.)
11 CPY3 Micro 0, 1 0 For engineering design use only
Copy all CXA8070 data for Full mode to Vcomp1&2 modes.
12 200V H.DUTY, H.TILT: 200V regulator adjustment Adj. 0~63 31 [31]
Note:
KV-27FS12/27FS16/29FS12/29FS12C
DX1A SERVICE LIST (#8): Audio Processing (AP) / BH3868FS
Device Name: BH3868FS { Audio Processor / ROHM } / IC7001 (A-board)
Slave Address: 82h
Register Control Register Data Data Data Initial Setting
Comment
No & Name Function & Link Type Range (32V&36V CRTs)
KV-27FS12/27FS16/29FS12/29FS12C
0 SVOL Volume: Offset for Volume 0~3 0
1 SBAL Balance: Offset for Balance 0~(3)~7 7
2 SBAS Bass: Offset for Bass 0~(3)~7 7 ( ): Settings at center
3 STRE Treble: Offset for Treble 0~(3)~7 7
4 BBLP BBE lowpass filter 0~15 0
5 BBHP BBE highpass filter 0~15 2
6 SREF Surround effect 0~7 11
7 AGC Auto gain control 0, 1 0
8 BBE BBE on/off 0, 1 1
Note:
-- 42 --
DX1A SERVICE LIST (#9): TruSurround (TRUS) / NJM2180
Device Name: NJM2180M { TruSurround 3D-Audio Processor / JRC } / IC4101 (S-board)
Device Control: Controlled through CXA1315M (Audio Control D/A, IC4103/S-board, Slave Address: 48h)
Register Control Register Data Data Data Initial Setting
Comment
No & Name Function & Link Type Range (32V&36V CRTs)
0 TS TruSurround effect selection 0~3 2 C: Common data
1 DMY1 Dummy data (No functions) C 0~255 0 DMY1 is used to fulfil the minimum requirement of 2 control items in each service control category.
Note:
DX1A SERVICE LIST (#10): MID1 (Common Data)
Device Name: CXD9509AQ { MID-X / Fujitsu & SONY } / IC3408 (B-board)
Slave Address: 2Eh { Controlled through MID-X Micro (IC3090/B-board, Slave Address: 64h) }
MID-X Micro (MASK-1): MB94918RPF-G-128-BND (Fujitsu Code: 128), MID-X Software: Version 03/30/00 (Used in the first month DX1A
production only.)
MID-X Micro (MASK-2): MB94918RPF-G-130-BND (Fujitsu Code: 130), MID-X Software: Version 04/20/00
Register Control Register Data Data Data Initial Setting
Comment
No & Name Function & Link Type Range (32V&36V CRTs)
MID Mode: All
(Single & P&P & Favorite)
0 DHPH Horizontal phase of the active display area C 0~255 91 C: Common data
1 DVPH Vertical phase of the active display area C 0~63 20
2 DHAR Horizontal size of the active display area C 0~255 240
3 DVAR Vertical size of the active display area C 0~255 135
4 DHPW Horizontal pulse width C 0~63 27
5 DVPW Vertical pulse width C 0~7 7
6 DYCD Delay of YC signal output C 0~63 2
7 DYSD Delay of YS signal output C 0~7 1
MID Mode: Signle & Favorite
-- 43 --
Single Single
Favorite
480i&p 1080i
8 MDHP Horizontal position of the main picture 0~255 33 13
9 MDVP Vertical position of the main picture 0~255 32 8 12
10 MDHS Horizontal size of the main picture 0~255 230 150
11 MDVS Vertical size of the main picture 0~255 120 135 111
MID Mode: P&P & Favorite
12 MLHP (Horizontal position of the multi pictures) 0~255 54
13 MLVP (Vertical position of the multi pictures) 0~255 31
MID Mode: Favorite
14 SDHP Horizontal position of the sub picture 0~255 173
15 SDVP Vertical position of the sub picture 0~255 12
16 SDHS Horizontal size of the sub picture 0~255 61
17 SDVS Vertical size of the sub picture 0~255 42
MID Mode: All
(Single & P&P & Favorite)
18 DPSW Switch of display output PLL C 0, 1 1
19 MDL0 Model selection 0 (0: 16x9, 1: 4x3) C 0, 1 0
Note:
KV-27FS12/27FS16/29FS12/29FS12C
DX1A SERVICE LIST (#11): MID2 (DRC-in Data)
KV-27FS12/27FS16/29FS12/29FS12C
Device Name: CXD9509AQ { MID-X / Fujitsu & SONY } / IC3408 (B-board)
Slave Address: 2Eh { Controlled through MID-X Micro (IC3090/B-board, Slave Address: 64h) }
MID-X Micro (MASK-1): MB94918RPF-G-128-BND (Fujitsu Code: 128), MID-X Software: Version 03/30/00 (Used in the first month DX1A
production only.)
MID-X Micro (MASK-2): MB94918RPF-G-130-BND (Fujitsu Code: 130), MID-X Software: Version 04/20/00
Register Control Register Data Data Data Initial Setting
No & Name Function & Link Type Range (32V&36V CRTs)
MID Mode: Single MID Mode: P&P & Favorite MID Mode: Freeze
YC YCbCr YC YCbCr YC YC YCbCr
480i 480i 480i 480i 480i-(R) 480i 480i
0 DRHP Horizontal position of the active display area (DRC-in) 0~255 120 116 131 129 137 138 136
-- 44 --
1 DRHS Hsize of the active display area (DRC-in) 0~255 174 174 167 167 168 165 165
2 DRVP Vposition of the active display area (DRC-in) 0~63 38 38 53 53 53 53 53
3 DRVS Vertical size of the active display area (DRC-in) 0~255 120 120 112 112 112 112 112
Note:
DX1A SERVICE LIST (#12): MID-3 (VDO-in Data) (Part-1)
Device Name: CXD9509AQ { MID-X / Fujitsu & SONY } / IC3408 (B-board)
Slave Address: 2Eh { Controlled through MID-X Micro (IC3090/B-board, Slave Address: 64h) }
MID-X Micro (MASK-1): MB94918RPF-G-128-BND (Fujitsu Code: 128), MID-X Software: Version 03/30/00 (Used in the first month DX1A
production only.)
MID-X Micro (MASK-2): MB94918RPF-G-130-BND (Fujitsu Code: 130), MID-X Software: Version 04/20/00
Register Control Register Data Data Data Initial Setting
Comment
No & Name Function & Link Type Range (32V&36V CRTs)
MID Mode: Single
YCbCr Dummy Dummy-480i settings are used
480P 480i for No Signal cases.
0 VDHP Horizontal position of the active display area (VDO-in) 0~255 118 179
1 VDHS Horizontal pixel size of the active display area (VDO-in) 0~255 159 199 These settings continue to the
2 VDVE Vertical even position of the active display area (VDO-in) 0~63 39 24 next page.
3 VDVS Vertical line size of the active display area (VDO-in) 0~255 129 56
YC YCbCr YCbCr Dummy
480i 480P 1080i 480i
4 VDVO Vertical odd position of the active display area (VDO-in) 0~3 0 0 0 0
5 VCPO Clamp pulse output timing (VDO-in) 0~255 95 70 40 90
6 VCWD Clamp pulse width (VDO-in) 0~7 3 3 3 3
7 VYCD Analog input YC delay (VDO-in) 0~63 0 0 0 0
YCbCr YCbCr
480P 1080i
8 VSTP PD stop line count of external PLL (VDO-in) 0~255 119 160
-- 45 --
9 VSTT PD start line count of external PLL (VDO-in) 0~15 7 0
MID Mode: All
(Single & P&P & Favorite)
10 VHSC Horizontal sync cycle (VDO-in) 0~255 130
DX1A SERVICE LIST (#12): MID-3 (VDO-in Data) (Part-2)
Register Data Initial Setting Data Initial Setting
Comment
No & Name (32V&36V CRTs) (32V&36V CRTs)
MID Mode: P&P / Favorite MID Mode: FREEZE
YC YCbCr YCbCr Dummy YCbCr YCbCr Dummy
480i 480P 1080i 480i 480P 1080i 480i
Dummy-480i settings are used for No Signal cases.
#0 VDHP (cont.) 197 127 91 179 131 98 179
#1 VDHS (cont.) 219 154 151 199 153 149 199
#2 VDVE (cont.) 24 53 37 24 53 37 24
#3 VDVS (cont.) 56 112 126 56 112 126 56
KV-27FS12/27FS16/29FS12/29FS12C
DX1A SERVICE LIST (#13): MID5 (Picture Data: MIDE) (Part-1)
Device Name: CXD9509AQ { MID-X / Fujitsu & SONY } / IC3408 (B-board)
Slave Address: 2Eh { Controlled through MID-X Micro (IC3090/B-board, Slave Address: 64h) }
MID-X Micro (MASK-1): MB94918RPF-G-128-BND (Fujitsu Code: 128), MID-X Software: Version 03/30/00
(Used in the first month DX1A production only.)
MID-X Micro (MASK-2): MB94918RPF-G-130-BND (Fujitsu Code: 130), MID-X Software: Version 04/20/00
Register Control Register Data Data Data Initial Setting Data Initial Setting Data Initial Setting Data Initial Setting
No & Name Function & Link Type Range (32V&36V CRTs) (32V&36V CRTs) (32V&36V CRTs) (32V&36V CRTs)
UHF/VHF & CVideo YCbCr-480i (DVD) YCbCr-480p YCbCr-1080i
Settings for P&P (Main)
Pro Movie Standard Vivid Pro Movie Standard Vivid Pro Movie Standard Vivid Pro Movie Standard Vivid
0 POP Selection of service data tables (Table #: 0~15) 0~15 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 MHLY Y coefficient code of Horizontal LPF (M) 0~3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
KV-27FS12/27FS16/29FS12/29FS12C
2 MHLC C coefficient code of Horizontal LPF (M) 0~3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
3 MVLY Y coefficient code of Vertical LPF (M) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
4 MVLC C coefficient code of Vertical LPF (M) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
5 MHYR Y coreing code of horizontal enhancement (M) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
6 MHYL Y cliping code of horizontal enhancement (M) 0~3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
7 MHYE Y level code of horizontal enhancement (M) 0~7 4 0 0 0 3 0 0 0 4 0 0 0 4 0 0 0
8 MHYO Y coefficient code of horizontal enhancement (M) 0, 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
9 MHCR C coreing code of horizontal enhancement (M) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
10 MHCL C cliping code of horizontal enhancement (M) 0~3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
11 MHCE C level code of horizontal enhancement (M) 0~7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
12 MHCO C coefficient code of horizontal enhancement (M) 0, 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
13 MVYR Y coreing code of vertical enhancement (M) 0~3 0 0 0 0 0 0 2 2 0 0 2 2 0 0 0 0
14 MVYL Y cliping code of vertical enhancement (M) 0~3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
-- 46 --
15 MVYE Y level code of vertical enhancement (M) 0~7 0 0 0 0 0 0 2 5 0 0 2 5 0 0 0 0
16 MVCR C coreing code of vertical enhancement (M) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
17 MVCL C cliping code of vertical enhancement (M) 0~3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
18 MVCE C level code of vertical enhancement (M) 0~7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
N
UHF/VHF & CV YCbCr-480i (DVD) YCbCr-480p YCbCr-1080i
Settings for P&P (Sub) Pro Movie Standard Vivid Pro Movie Standard Vivid Pro Movie Standard Vivid Pro Movie Standard Vivid
0 POP Selection of service data tables (Table #: 0~15) 0~15 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
19 SHLY Y coefficient code of Horizontal LPF (S) 0~7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
20 SHLC C coefficient code of Horizontal LPF (S) 0~7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
21 SVLY Y coefficient code of Vertical LPF (S) 0~7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
22 SVLC C coefficient code of Vertical LPF (S) 0~7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
23 SHYR Y coreing code of horizontal enhancement (S) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
24 SHYL Y cliping code of horizontal enhancement (S) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
25 SHYE Y level code of horizontal enhancement (S) 0~7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
26 SHYO Y coefficient code of horizontal enhancement (S) 0, 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
27 SHCR C coreing code of horizontal enhancement (S) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
28 SHCL C cliping code of horizontal enhancement (S) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
29 SHCE C level code of horizontal enhancement (S) 0~7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
30 SHCO C coefficient code of horizontal enhancement (S) 0, 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
31 SVYR Y coreing code of vertical enhancement (S) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
32 SVYL Y cliping code of vertical enhancement (S) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
33 SVYE Y level code of vertical enhancement (S) 0~7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
34 SVCR C coreing code of vertical enhancement (S) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
35 SVCL C cliping code of vertical enhancement (S) 0~3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
36 SVCE C level code of vertical enhancement (S) 0~7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
DX1A SERVICE LIST (#14): On-Screen Display (OSD)
Device Name: M306V2ME-150FP { System Micro (MASK) / Mitsubishi } / IC701 (A-board)
Slave Address: 60h
System Micro Software: Version 1.0
Register Control Register Data Data Data Initial Setting
No & Name Function & Link Type Range (32V&36V CRTs)
Comment
0 HPOS OSD horizontal position C 0~255 17 C: Common data
1 HPOF Horizontal position for Favorite mode C 0~255 26
2 VPOS OSD vertical position C 0~255 5
3 VPOT Vertical position for P&P (Twin) mode C 0~255 32
Note:
DX1A SERVICE LIST (#19): IDENTIFICATION (ID)
Device Name: M306V2ME-150FP { System Micro (MASK) / Mitsubishi } / IC701 (A-board)
Slave Address: 60h
-- 47 --
System Micro Software: Version 1.0
Register Control Register Data Data Data Initial Setting
Comment
No & Name Function & Link Type Range (32V&36V CRTs)
Shipping Destination-related Settings US Canda Latin
0 ID0 Selection of OSD languages & color systems 0~255 89 89 25
1 ID1 Selection of composite & s-video inputs 0~255 127 127 127
2 ID2 Selection of audio-related controls 0~255 239 239 239
3 ID3 Selection of basic system settings 0~255 98 82 194
4 ID4 Selection of basic system settings 0~255 203 203 203
5 ID5 Selection of advanced system settings 0~255 177 177 177
6 ID6 Selection of sub picture-related settings 0~255 54 54 54
7 ID7 Selection of some reserved settings 0~255 24 24 88
Note:
KV-27FS12/27FS16/29FS12/29FS12C
DX1A SERVICE LIST (#17): Closed Caption Display & Parental Control (CCD&VCHIP)
Device Name: CXP85840A-039Q { CCD&Vchip Micro (MASK) / SONY } / IC3602 (Main) & IC3601 (Sub) (B-board)
Slave Address: 68h (Main) & 6Ch (Sub)
CCD&Vchip Micro Software: Version 2.14
Register Control Register Data Data Data Initial Setting
Comment
No & Name Function & Link Type Range (32V&36V CRTs)
0 HPRM Horizontal position of CCD (Main) C 0~255 46 C: Common data
1 HPRS Horizontal position of CCD (Sub) C 0~255 46
KV-27FS12/27FS16/29FS12/29FS12C
2 RND OSD rounding control C 0, 1 1
3 CCDI Interuption cointrol C 0~7 3
4 CRIP CRI count & parity count C 0~7 4
5 CRIT Charge/Discharge timing control for slice voltage level C 0, 1 0 0: MASK-type micro, 1: OTP-type micro
6 CHMK Horizontal mask width C 0~63 42
7 FPOL Field polarity selection C 0, 1 1
8 LANG C 0~3 0
9 DATA Switch for CCD service/test data C 0, 1 0
10 VCHIP Selection of Vchip controls C 0, 1 0
Note:
-- 48 --
DX1A SERVICE LIST (#16): ID-1 Detection (ID1)
Device Name: CXD2085M { ID-1 Decoder / SONY } / IC3603 (B-board)
Slave Address: 40h
Register Control Register Data Data Data Initial Setting
Comment
No & Name Function & Link Type Range (32V&36V CRTs)
XJGLK: Setting for memorizing or not the ID-1 detection status
0 XJGL C 0, 1 0 C: Common data
when the VTR in Fast Forward (FF) or Rewind (REW) mode
1 LNJI LNJ1: Setting for the multi/single-line ID-1 detection C 0, 1 0
Note:
Other servcie controls related to CXD2085 (IDSW & DATA) are lised in Service List (CXA2150P-4) for easier engineering adjustment.
DX1A SERVICE LIST (#15): SNNR
Related Control Devices: