Text preview for : BFL200F-TE.pdf part of MAKITA BFL200F-TE MAKITA BFL200F-TE.pdf
Back to : BFL200F-TE.pdf | Home
T ECHNICAL INFORMATION
Models No. BFL121F / BFL200F
PRODUCT
P 1 / 23
Description Cordless Angle Screwdrivers 12V
CONCEPTION AND MAIN APPLICATIONS L
These Cordless Angle Screwdrivers have been developed
as upgraded sister tools to models of Makita 6706D. H
Having the same features and benefits as tools of
Model 6706D series, these new drivers for automobile factories
feature higher torque, torque accuracy and built in job light. W
The variations of these models are as listed below. Dimensions : mm ( " )
BFL121F and BFL200F
Fastening Type of the equipped
Model No. torque bit or socket Length w/ BH1220 430 (17)
(L) w/ BH1233 454 (17-7/8)
BFL121FZ Socket, Square 9.5mm (3/8")
BFL121F1Z E-form Bit, Hex 6.35mm (1/4") Height ( H ) 92 (3-5/8)
BFL121F2Z 5 - 12N.m C-form Bit, Hex 6.35mm (1/4") Width ( W ) 71 (2-13/16)
BFL121F3Z (44.3-106 in.lbs) E-form Bit, Hex 8mm (5/16")
BFL121F4Z C-form Bit, Hex 8mm (5/16")
BFL121F5Z Socket, Square 6.35mm (1/4")
BFL200FZ Socket, Square 9.5mm (3/8")
BFL200F1Z E-form Bit, Hex 6.35mm (1/4")
BFL200F2Z 8 - 20N.m C-form Bit, Hex 6.35mm (1/4")
BFL200F3Z (70.9-177 in.lbs) E-form Bit, Hex 8mm (5/16")
BFL200F4Z C-form Bit, Hex 8mm (5/16")
BFL200F5Z Socket, Square 6.35mm (1/4")
Specification
Model No. BFL121F BFL200F
Type of cell Ni - MH
Battery Voltage : V 12
2.0 w/ BH1220
Capacity : Ah
3.3 w/ BH1233
No load speed : min-1 = rpm 410 220
Fastening torque : N.m (in.lbs) 5 - 12 (44.3 - 106) 8 - 20 (70.9 - 177)
Electric brake Yes
Torque adjustment Yes (Adjust grip is required.)
Soft starter Yes
Reverse switch Yes
Standard equipment
* Protector .................................................................... 1 pc. (only for some countries)
* Adjust grip for torque adjusting ................................ 1 pc. (only for some countries)
< Note > The standard equipment for the tool shown may differ from country to country.
Optional accessories
* Battery BH1220 * Charger DC14SA * Angle head set
* Battery BH1233 * Charger DC24SA * Adjust grip for torque adjusting
* Auto refresh adapter ADP03
* Protectors ( red, blue, yellow and see-through )
Features and benefits P 2 / 23
BFL121F and BFL200F
Indication Lamp and Beeper
inform user of;
* Sufficient fastening = Green on
* Insufficient fastening = Red on
*Higher Torque Accuracy and Beeping
* Warning that remaining battery
Torque accuracy: power is little = Red on
Plus or minus 10%, Plus or minus 3 sigma, and Beeping
Cm is more than or equal to 1.67 * Too little power to rotate
the machine = Motor stops with Red on
and Beeping
* Refer to page 3 in detail about this matter.
Torque adjusting system D28 Type Motor
just for the manufacturing line Externally accessible brushes
Impossible to change fastening torque Two-piece motor with replace-
previously set by factory, without able armature
adjust grip Uses compact and light, yet
powerful rare earth magnet
Extra-rigid, Aluminum-alloy
Angle Head
Head height:
28.5mm (1- 1/8")
Anti-Slip Dimpled Grip
Easily operatable ON-OFF Switch
equipped with a Delayed re-starter
Center height:
13.5mm (1/2") *Conveniently Located
Forward/Reverse Push Button
Built in Electronic System featuring
Soft start to suppress Delayed re-starter
return torque The restarting delayer controls the motor
at start-ups so that it does not start till one second passes
after a screw has been driven ; the motor does not
start even if switch trigger is pulled.
Built-in
Job Light Consequently, reduced considerably deviation
from pre-set fastening torque , which is caused
Lighting up automatically
by unintentional over-tightening.
with start of motor, and
lighting on till 10 sec. passes
after switching off.
Uses Machine Screws for
Assembling Motor Housing
Auto Stop System 2.0Ah Batteries BH1220
By sensing battery's
3.3Ah Batteries BH1233
power drop.
Protector (option)
Protects workpiece from scratches.
Features and benefits P 3 / 23
Indication lamp, buzzer and auto stop system
In case of no trouble on the result of work and on the machine, the lamp and beeper inform of the following matters.
Lamp Beeper Auto stop What the lamp, beeper and auto stop system inform of.
Lights up in the A series of Under testing the function of indication
order of green, short beeps lamp and beeper, when installing battery.
red and white.
Finish of single fastening process with reaching
the pre-set fastening torque.
Lights up At this time, clutch works and delayed restarter
No beep ON
in green. keeps the motor still for one second after finishing
sufficient fastening process, to avoid the unintentional
over-tightening which will occur by mis-operation
of switch trigger.
In case of trouble on the result of work, or on the machine, the lamp and buzzer inform of the following matters.
What the lamp, beeper and
Lamp Beeper Auto stop auto stop system inform of. Action to be taken
Insufficiently finished single Try again to fasten the screw
Lights up A long fastening process, without or bolt.
in red. beep reaching the pre-set fastening It is important to pull the switch
torque. trigger on, until clutch works.
Remaining battery Motor rotates on, however, it is
A series power is little. recommended to replace with
Flickers in red of long the fully charged battery in the
slowly. beeps appropriate time.
Impossible to fasten screws Immediately replace the
A long or bolts with the pre-set old battery with the fully
Lights up beep ON
fastening torque any more. charged battery.
in red.
Lights up in A series Warning of abnormal drop of Motor does not rotate in spite of
red and green of long battery voltage for some pulling switch trigger.
ON
alternately. beeps reason. The warning by lamp and buzzer
stops with removing battery.
A series Warning of over heat on Remove the battery immediately
Flickers controller. and cool the machine down.
of short ON
in red
beeps
quickly.
Flickers in Trouble on clutch system. Ask MAKITA authorized or
A series
red and green factory service center for repair
of long ON
alternately. or adjustment.
beeps
The battery has been installed Release the switch trigger.
Lights up in A series with keeping switch trigger
red and green of long ON pulled.
alternately. beeps
Features and benefits P 4 / 23
Identification Plate for BFL080F Series Models
BFL080F Series Models (BFL080F, BFL120F, BFL121F and BFL200F) are equipped with
Identification Plates for easy control in your factory.
Even if the name plates would fall off the machines, or even if it is too difficult to read the indications from the worn
name plates, BFL080F Series Models can be easily identified from the identification plates.
***** Identification number with 5 digits;
Identification plate
With this 5 digits, it can be
8 - 20N.m identified, (for example) to which
manufacturing section the relative
machine is employed.
The identification number is put
by MAKITA, independent of the
Torque range; serial numbers.
Model No. can be identified with
this indication as mentioned below.
***** ***** *****
2 - 8N.m 5 - 12N.m 8 - 20N.m
BFL080F BFL120F BFL200F
Yellow plate BFL121F Blue plate Red plate
How to control the BFL080F series models with the identification plate
BFL080F series models are employed in some factory, for example , as listed below.
Employed Indications on the identification plate Employed
Manufacturing model Torque range Identification No. quantity
section A BFL080F 2 - 8N.m 00001 - 00250 250
BFL120F 5 - 12N.m 00123 - 00275 153
Employed Indications on the identification plate Employed
Manufacturing model Torque range Identification No. quantity
section B BFL080F 2 - 8N.m 00251 - 00300 50
BFL120F 5 - 12N.m 10300 - 10449, 00899, 15689, 152
Employed Indications on the identification plate Employed
Manufacturing model Torque range Identification No. quantity
section C BFL121F 5 - 12N.m 00030 - 00119, 00830 - 00836, 97
BFL200F 8 - 20N.m 50025 - 50099, 00830 - 00836, 15689, 83
You can identify the model No. and to which manufacturing section the relative machine belongs, from the
indications on the plates.
00237 00899 00117
2 - 8N.m 5 - 12N.m 5 - 12N.m
BFL080F employed in BFL120F employed in BFL121F employed in
manufacturing section A manufacturing section B manufacturing section C
00129 00296 50057
5 - 12N.m 2 - 8N.m 8 - 20N.m
BFL120F employed in BFL080F employed in BFL200F employed in
manufacturing section A manufacturing section B manufacturing section C
Features and benefits P 5 / 23
Combination of bits or sockets with BFL080 series models
Model No. BFL080FZ BFL120FZ BFL080F1Z BFL120F1Z BFL080F2Z BFL120F2Z
(Ref. to page 1.) BFL121FZ BFL200FZ BFL121F1Z BFL200F1Z BFL121F2Z BFL200F2Z
Socket, E-form Bit, Hex 6.35mm (1/4") C-form Bit, Hex 6.35mm (1/4")
Square 9.5mm (3/8") 6.35mm
(1/4")
6.35mm
(1/4")
Available bits Apperox. 9mm
or (11/32")
In case of No.2 bit
sockets Apperox. 8mm
Apperox. 9mm (11/32") 6.35mm (5/16")
9.5mm (1/4")
(3/8")