Text preview for : Service Bulletin OST-F1177-1.PDF part of DENON Service Bulletin OST-F1177-1 DENON DVD Video Player DVD Video Player Denon - DVD-3930 & 3930CI Service Bulletin OST-F1177-1.PDF
Back to : Service Bulletin OST-F117 | Home
100 Corporate Drive Mahwah, NJ 07430
Service Bulletin
No. : OST-F1177-1
Date: June 14, 2007
_____________________________________________________________
Model: DVD-3930CI, DVD-3930
Subject: Countermeasure for improving the malfunction (See Symptom).
Symptom: Video artifacts become visible after a while during de-interlacing
with PAL movie material (Only with film material).
Solution: The MICON software has been corrected MODIFICATION: Please
download the improved program file to your PC and update the MICON software
of your customer's unit using the following instruction. The update takes about 8
minutes.
Confirmation of the Version:
(1) Turn off the Power switch of the unit once. While holding the "PLAY" and
"OPEN/CLOSE" buttons on the unit down simultaneously, switch the Power on.
(2) When " >|| " mark was indicated on the FL Display, press the numeral
buttons "3", "2", "6" and "5" on the Remote Control.
(3) The following Versions appear every time the "MENU" button on the Remote
Control is pressed 4 times. Confirm the following versions "IP 070518" on FL
Display.
Caution during the rewriting operation:
Do not turn the Power of the unit off during the rewriting operation.
______________________________________________________________________________________
CONFIDENTIALITY NOTICE:
The information contained in this document is intended for the exclusive use by DENON Authorized Service Centers and their
employees. This document may contain information that is privileged, confidential and may be protected from disclosure under
applicable laws and terms of the DENON Service Agreement. Any distribution, disclosure, dissemination or copying of this
document and the information it contains is prohibited. No responsibility will be accepted by DENON for any damage, injury or loss
resulting from the misuse of the information contained in this document.
Version Up tool setup
1. Download the "SiOptix_Developer_ToolKit.zip" file and
"DTK_Install_GUD_1.004.pdf" file to your PC.
2. Click the "setup.exe" file.
(Instructions will be provided in DTK install shield GUI)
3. Open the "Router Manager" for comport setting.
(Starts > All Programs > Silicon Optix > Developers ToolKit > Router
Manager)
()
(i) Select "Boards In System" tab
Click "add Board..." button
OST-F1177 Page 3/17 Z07-005
(ii) Choose "Connection type": COM
(iii)select radio button "Specify Connection ID with `Anonymous Board Name"
(iv) set "Connect ID": COM:1 (if the user connect the 3930 DVD player to PC
through COM2 or COM3, then set Connect ID to COM:2 or COM:3
(v) then click 'Test Connection' button
(vi) After "Connection via COM:1 is successfully" message shown in the status
window,
()
()
()
()
()
Click "Add" button. The following will be shown in the "Boards in System"
OST-F1177 Page 4/17 Z07-005
Click "Close" button
* step 4 only need to be done once on the PC having SOI DTK installed
OST-F1177 Page 5/17 Z07-005
H/W Setting for DVD2930/3930 IP firmware update procedure
(1)Connect RS-232C cable
(Choose straight type cable. If cross type cable is used, it is not possible to
connect it.)
OST-F1177 Page 6/17 Z07-005
(2).H/W Setting (enter DVD Player SETUP MODE and IP firmware UPDATE
MODE)
1) Push "OPEN/CLOSE" and "PLAY" button simultaneously and turn on the AC
Power.
If you can see the following indicator, you can enter SETUP MODE.
This indicator is "SETUP MODE" correctly.
OST-F1177 Page 7/17 Z07-005
(3)Push "STOP" and "FORWARD SKIP" button simultaneously
And then you can see "TEST MODE" character on FL display
OST-F1177 Page 8/17 Z07-005
(4)Push REVERS SKIP button twice
And then you can see "TF RS232C SEL" character on FL display
OST-F1177 Page 9/17 Z07-005
(5)Push PLAY button
And then you can see "TF1 232CSEL-H" character on FL display
(6)Push PLAY button
If you can see "TF1 SET HIGH" character on FL display, you can enter IP
firmware UPDATE MODE
Successful next you execute S/W Setting using UPDATE program
(See attached 3930 SW setting.doc file)
OST-F1177 Page 10/17 Z07-005
S/W Setting for DVD3930 IP firmware update
You have to do H/W Setting before you start IP firmware update.
Connection with DVD3930 to PC through serial cable
Enter IP firmware update mode
(1)Open "API debugger"
Starts > All Programs > Silicon Optix > Developers ToolKit > API Debugger
()
()
()
i) Find FSPCreateRamDrive in the API list and then select it by clicking on it.
ii) In the parameters, choose
by_drive_id = 77
u32_drive_size = 5000000
u32_options = 0
iii) Click "Connect" button
OST-F1177 Page 11/17 Z07-005
()
iv) Click "add Board..." button.
v) After "Connection successfully set" message shown in the status window.
vi) Once the parameters are filled in, click on "Call API".
vii) The status message should display "Call completed successfully".
The ram drive is now ready for use.
()
()
()
()
viii) Click "Close" button
OST-F1177 Page 12/17 Z07-005
(2) Open File Manager
1) Starts > All Programs > Silicon Optix > Developers ToolKit > File Manager
Click `Connect' button
(Router Manager will automatically detect "Routers on the Network", which is
shown in
"DTK Routers On The Network" dropdown box)
2) Highlight Anonymous (COM:1), then click "Connect To Board" button.
OST-F1177 Page 13/17 Z07-005
1) Format the C: drive at the target system
After connection established (messages in Session log window), click on C:
under Target System (Target system window panel on the right side of File
manager)
()
i) there is old version of .brec file under C: drive, so click Tools > Format drive
() ()
ii) Click "Start" button to format the C: drive
iii) When you finish formatting the C: drive, then click "Exit" button.
OST-F1177 Page 14/17 Z07-005
(4) Download the update firmware at the target system.
Highlight the .brec to be downloaded to 3930 DVD player, drag it to the right
side panel (target system window panel) by mouse (or click "Upload/Download"
button on the tool bar).
Progress bar at the bottom will be blinking
When the downloading is complete, the user would see .brec under M: drive at
target system window panel. This process will take about 8 min.
OST-F1177 Page 15/17 Z07-005
(5) Update firmware
Click Tools > Advanced > Update Firmware
()
i) Click "Browse" button, and highlight the .brec :
()
ii) Then click "OK" button.
()
iii) Finally click "Update" button.
Progress bar at the bottom of File manager will be blinking:
OST-F1177 Page 16/17 Z07-005
()
()
This process will take about 2 minutes.
Wait until progress bar stops blinking (indicate programming into Flash is
complete),
iv) Click "Disconnect" the File Manager.
v) Finally Click "Close" button.
OST-F1177 Page 17/17 Z07-005