Text preview for : IC-PCR & R1500 Retrieve.pdf part of IC-PCR & R1500 Retrieve



Back to : IC-PCR & R1500 Retrieve.p | Home

Communication Receiver Model Nos.: IC-R1500 & IC-PCR1500 FCC ID: AFJ288000
Applicant: ICOM Incorporated 1-1-32, Kamiminami, Hirano-ku Osaka, Japan, 547-0003
Tested in Accordance With

Federal Communications Commission (FCC) 47 CFR, Part 15, Subpart B Scanning Receivers Operating in the Frequency Band 0.010 to 3299.9999 MHz (excluding cellular bands)
UltraTech's File No.: ICOM-122FCC15B

This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: January 10, 2006 Report Prepared by: Dharmajit Solanki Tested by: Wayne Wu, EMI/RFI Technician

Issued Date: January 10, 2006

Test Dates: Dec.21 - Jan.06, 2006

The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the US Government.

UltraTech
3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com, Email: [email protected], Email: [email protected]
2

31040/SIT

C-1376

46390-2049

200093-0

SL2-IN-E-1119R

00-034

FCC Part 15, Subpart B, Part 15.121 Communication Receiver, Models: IC-R1500 & IC-PCR1500

Page 1 FCC ID: AFJ288000

TABLE OF CONTENTS
EXHIBIT 1. EXHIBIT 2. 2.1. 2.2. 2.3. SUBMITTAL CHECK LIST..................................................................................................................... 3 INTRODUCTION ...................................................................................................................................... 4

SCOPE...................................................................................................................................................................... 4 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................... 4 NORMATIVE REFERENCES ................................................................................................................................ 4 PERFORMANCE ASSESSMENT ........................................................................................................... 5

EXHIBIT 3. 3.1. 3.2. 3.3. 3.4. 3.5. 3.6.

CLIENT INFORMATION....................................................................................................................................... 5 EQUIPMENT UNDER TEST (EUT) INFORMATION ......................................................................................... 5 EUT'S TECHNICAL SPECIFICATIONS .............................................................................................................. 6 LIST OF EUT'S PORTS.......................................................................................................................................... 6 ANCILLARY EQUIPMENT ................................................................................................................................... 6 DRAWING OF TEST SETUP................................................................................................................................. 7 EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS ............................ 2

EXHIBIT 4. 4.1. 4.2.

CLIMATE TEST CONDITIONS ............................................................................................................................ 2 OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS.......................................... 2 SUMMARY OF TEST RESULTS ............................................................................................................ 7

EXHIBIT 5. 5.1. 5.2. 5.3.

LOCATION OF TESTS........................................................................................................................................... 7 APPLICABILITY & SUMMARY OF EMC EMISSION TEST RESULTS .......................................................... 7 MODIFICATIONS REQUIRED FOR COMPLIANCE.......................................................................................... 7 MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS............................ 8

EXHIBIT 6.

6.1. TEST PROCEDURES.............................................................................................................................................. 8 6.2. MEASUREMENT UNCERTAINTIES ................................................................................................................... 8 6.3. MEASUREMENT EQUIPMENT USED ................................................................................................................ 8 6.4. AC POWER LINE CONDUCTED EMISSIONS [§ 15.107(A)]............................................................................. 9 6.4.1. LIMITS.............................................................................................................................................................. 9 6.4.2. METHOD OF MEASUREMENTS.................................................................................................................... 9 6.4.3. TEST EQUIPMENT LIST................................................................................................................................. 9 6.4.4. PHOTOS OF TEST SETUP.............................................................................................................................. 9 6.4.5. TEST DATA .................................................................................................................................................... 10 6.5. RECEIVER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§15.111(A)] ........ 12 6.5.1. LIMITS............................................................................................................................................................ 12 6.5.2. METHOD OF MEASUREMENTS.................................................................................................................. 12 6.5.3. TEST EQUIPMENT LIST............................................................................................................................... 12 6.5.4. TEST ARRANGEMENT.................................................................................................................................. 13 6.5.5. TEST DATA .................................................................................................................................................... 14 6.6. RECEIVER SPURIOUS/HARMONIC RADIATED EMISSIONS [§ 15.109(A)]............................................... 19 6.6.1. LIMITS............................................................................................................................................................ 19 6.6.2. METHOD OF MEASUREMENTS.................................................................................................................. 19 6.6.3. TEST EQUIPMENT LIST............................................................................................................................... 20 6.6.4. PHOTOS OF TEST SETUP............................................................................................................................ 20 6.6.5. TEST DATA .................................................................................................................................................... 21 ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC Part 15, Subpart B, Part 15.121 Communication Receiver, Models: IC-R1500 & IC-PCR1500

Page 2 FCC ID: AFJ288000

6.7.

RADIATED EMISSIONS FROM CLASS B UNINTENTIONAL RADIATORS (DIGITAL DEVICES) [§ 15.109(A)].............................................................................................................................................................. 22 6.7.1. LIMITS............................................................................................................................................................ 22 6.7.2. METHOD OF MEASUREMENTS.................................................................................................................. 22 6.7.3. TEST EQUIPMENT LIST............................................................................................................................... 23 6.7.4. PHOTOS OF TEST SETUP............................................................................................................................ 23 6.7.5. TEST DATA .................................................................................................................................................... 24 6.8. REQUIREMENTS FOR SCANNING RECEIVERS [47 CFR 15.121] ................................................................ 25 6.8.1. FCC RULES ................................................................................................................................................... 25 6.8.2. DECLARATION FOR COMPLIANCE WITH FCC §15.121 ......................................................................... 27 6.9. SCANNING RECEIVERS CELLULAR BAND REJECTION [47 CFR 15.121(B)] ........................................... 28 6.9.1. LIMITS............................................................................................................................................................ 28 6.9.2. METHOD OF MEASUREMENTS.................................................................................................................. 28 6.9.3. TEST EQUIPMENT LIST............................................................................................................................... 29 6.9.4. TEST DATA .................................................................................................................................................... 29 MEASUREMENT UNCERTAINTY...................................................................................................... 31

EXHIBIT 7. 7.1. 7.2.

LINE CONDUCTED EMISSION MEASUREMENT UNCERTAINTY ............................................................. 31 RADIATED EMISSION MEASUREMENT UNCERTAINTY ........................................................................... 32

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC Part 15, Subpart B, Part 15.121 Communication Receiver, Models: IC-R1500 & IC-PCR1500

Page 3 FCC ID: AFJ288000

EXHIBIT 1.
Annex No. --

SUBMITTAL CHECK LIST
Description of Contents Exhibit 1: Submittal check lists Exhibit 2: Introduction Exhibit 3: Performance Assessment Exhibit 4: EUT Operation and Configuration during Tests Exhibit 5: Summary of test Results Exhibit 6: Measurement Data Exhibit 7: Measurement Uncertainty Radiated Emissions Test Setup Photos External EUT Photos Internal EUT Photos Cover Letter for Certification Request. Letter from the Applicant to appoint Ultratech to act as an agent Letter from the Applicant to request for Confidentiality Filing Manufacturer Attestation Letter Part 2.1033(b)(10) for Scanning Receiver ID Label Location of ID Label Block Diagram Schematics IC-R1500 & IC-PCR1500 Circuit Description N/A IC-R1500 & IC-PCR1500 Instruction Manual Quality Check (OK) OK

Exhibit Type Test Report

1 2 3 4

Test Setup Photos External Photos of EUT Internal Photos of EUT Cover Letters

OK OK OK OK

5 6 7 8 9 10 11

Attestation Statements ID Label/Location Info Block Diagrams Schematic Diagrams Operational Description RF Exposure Info Users Manual

OK OK OK OK OK N/A OK

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC Part 15, Subpart B, Part 15.121 Communication Receiver, Models: IC-R1500 & IC-PCR1500

Page 4 FCC ID: AFJ288000

EXHIBIT 2.
2.1.
Title: Purpose of Test: Test Procedures:

INTRODUCTION
FCC Part 15, Subpart B, Sections 15.107, 15.109, 15.111 & 15.121 Code of Federal Regulations (CFR), Title 47, Telecommunication, Part 15 To gain FCC Certification Authorization for Scanning Receivers Operating in 0.010 to 3299.9999 MHz (excluding cellular bands) Band. Both conducted and radiated emissions measurements were conducted in accordance with American National Standards Institute ANSI C63.4 - American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz. Commercial, industrial or business environment.

SCOPE

Reference:

Environmental Classification:

2.2.
None.

RELATED SUBMITTAL(S)/GRANT(S)

2.3.

NORMATIVE REFERENCES
YEAR 2005 2003 Title Code of Federal Regulations ­ Telecommunication American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz Limits and Methods of Measurements of Radio Disturbance Characteristics of Information Technology Equipment Specification for radio disturbance and immunity measuring apparatus and methods. Part 1-1: Measuring Apparatus Specification for radio disturbance and immunity measuring apparatus and methods. Part 2-1: Conducted disturbance measurement Specification for radio disturbance and immunity measuring apparatus and methods. Part 2-3: Radiated disturbance measurement

Publication FCC CFR 47 Parts 0-19, 80-End ANSI C63.4

CISPR 22 +A1 EN 55022 CISPR 16-1-1

2003-04-10 2004-10-14 2003 2003

CISPR 16-2-1

2003

CISPR 16-2-3

2003

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC Part 15, Subpart B, Part 15.121 Communication Receiver, Models: IC-R1500 & IC-PCR1500

Page 5 FCC ID: AFJ288000

EXHIBIT 3.
3.1.

PERFORMANCE ASSESSMENT

CLIENT INFORMATION
APPLICANT

Name: Address:

ICOM Incorporated 1-1-32, Kamiminami Hirano-ku, Osaka Japan, 547-003 Mr. Kenji Asano Phone #: +81-66-793-5302 Fax #: +81-66-793-0013 Email Address: [email protected]

Contact Person:

MANUFACTURER Name: Address: ICOM Incorporated 1-1-32, Kamiminami Hirano-ku, Osaka Japan, 547-0003 Mr. Kenji Asano Phone #: +81-66-793-5302 Fax #: +81-66-793-0013 Email Address: [email protected]

Contact Person:

3.2.

EQUIPMENT UNDER TEST (EUT) INFORMATION

The following information (with the exception of the Date of Receipt) has been supplied by the applicant. Brand Name: Product Name: Model Name or Number: Serial Number: Type of Equipment: Accessories: Power input source: ICOM Incorporated Communication Receiver IC-R1500 0000008 Scanning Receiver Icom AC/DC Power Supply, Model DFU105180, IN: 120VAC 60Hz, 29W, OUT: 10.5 VDC, 1.8A. 10.5 VDC Adapter

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC Part 15, Subpart B, Part 15.121 Communication Receiver, Models: IC-R1500 & IC-PCR1500

Page 6 FCC ID: AFJ288000

3.3.

EUT'S TECHNICAL SPECIFICATIONS
RECEIVER Fixed or Mobile 10.5 VDC Adapter 0.010 to 3299.9999 MHz (excluding cellular bands) 50 Ohms

Equipment Type: Power Supply Requirement: Operating Frequency Range: RF Input Impedance:

3.4.

LIST OF EUT'S PORTS
EUT's Port Description Antenna Connector External Speaker Jack DC IN Packet Controller USB Number of Identical Ports 1 1 1 1 1 1 Connector Type BNC Female SP jack Single Pin male Single Pin Female RJ11 USB Cable Type (Shielded/Nonshielded) N/A Non-Shielded Non-Shielded Non-Shielded Non-Shielded Non-Shielded

Port Number 1 2 3 4 5 6

3.5.

ANCILLARY EQUIPMENT

The EUT was tested while connected to the following representative configuration of ancillary equipment necessary to exercise the ports during tests: Ancillary Equipment # 1 Description: Brand name: Model Name or Number: Serial Number: Cable Type: Ancillary Equipment # 2 Description: Brand name: Cable Type:

AC/DC Power Supply ICOM DFU105180 N/A Non-Shielded

Audio Speaker (8 Ohm) Polk Non-Shielded

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC Part 15, Subpart B, Part 15.121 Communication Receiver, Models: IC-R1500 & IC-PCR1500

Page 7 FCC ID: AFJ288000

3.6.

DRAWING OF TEST SETUP

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC Part 15, Subpart B, Part 15.121 Communication Receiver, Models: IC-R1500 & IC-PCR1500

Page 2 FCC ID: AFJ288000

EXHIBIT 4.
4.1.

EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS

CLIMATE TEST CONDITIONS
21oC 51% 102 kPa 10.5 VDC

The climate conditions of the test environment are as follows: Temperature: Humidity: Pressure: Power input source:

4.2.

OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS
The receiver was operated in the normal intended mode during testing None None The EUT's was tested with its antenna attached for radiated emissions.

Operating Modes: Special Test Software: Special Hardware Used: Receiver Test Antenna:

Receiver Test Signals Frequency Band(s): Test Frequency(ies): (Near lowest, near middle & near highest frequencies in the frequency range of operation.) 0.010 to 3299.9999 MHz (excluding cellular bands) 30, 445 and 960 MHz

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 7 FCC ID: AFJ288000

EXHIBIT 5.
5.1.

SUMMARY OF TEST RESULTS

LOCATION OF TESTS

All of the measurements described in this report were performed at Ultratech Group of Labs located in the city of Oakville, Province of Ontario, Canada. AC Powerline Conducted Emissions were performed in UltraTech's shielded room, 16'(L) by 12'(W) by 12'(H). Radiated Emissions were performed at the Ultratech's 3-10 TDK Semi-Anechoic Chamber situated in the Town of Oakville, province of Ontario. This test site been calibrated in accordance with ANSI C63.4, and found to be in compliance with the requirements of Sec. 2.948 of the FCC Rules. The descriptions and site measurement data of the Oakville 3-10 TDK Semi-Anechoic Chamber has been filed with FCC office (FCC File No.: 31040/SIT 1300B3) and Industry Canada office (Industry Canada File No.: IC2049-1). Last Date of Site Calibration: June. 20, 2005.

5.2.

APPLICABILITY & SUMMARY OF EMC EMISSION TEST RESULTS
Test Requirements Compliance (Yes/No)

FCC Part 15, Subpart B

15.107(a), Class B 15.111(a) 15.109(a) 15.121

AC Power Line Conducted Emissions Measurements Receiver Antenna Power Conducted Emissions for Non-Integral Antenna Port Radiated Emissions from Scanning Receivers & Class B Digital Device Requirements for Scanning Receivers

Yes Yes Yes Yes

5.3.
None.

MODIFICATIONS REQUIRED FOR COMPLIANCE

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 8 FCC ID: AFJ288000

EXHIBIT 6.

MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS

6.1.

TEST PROCEDURES

Please refer to Ultratech Test Procedures, File# ULTR-P001-2004 and for Test Procedures.

6.2.

MEASUREMENT UNCERTAINTIES

The measurement uncertainties stated were calculated in accordance with requirements of UKAS Document LAB 34 with a confidence level of 95%. Please refer to Exhibit 6 for Measurement Uncertainties.

6.3.

MEASUREMENT EQUIPMENT USED

The measurement equipment used complied with the requirements of the Standards referenced in the Methods & Procedures ANSI C63.4 and CIPSR 16-1-1.

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 9 FCC ID: AFJ288000

6.4.

AC POWER LINE CONDUCTED EMISSIONS [§ 15.107(a)]

6.4.1. Limits
The equipment shall meet the limits of the following table:
Frequency of emissions (MHz) Class B Conducted Limit (dBµV) Measuring Bandwidth

Quasi-Peak

Average 56 to 46* 46 50

0.15 to 0.5 66 to 56* 0.5 to 5 56 5 to 30 60 * Decreasing linearly with logarithm of frequency

RBW = 9 kHz VBW > 9 kHz for QP VBW = 1 Hz for Average

6.4.2. Method of Measurements
Refer to Ultratech Test Procedures ULTR-P001-200 & ANSI C63.4 for method of measurements.

6.4.3. Test Equipment List
Test Instruments EMI Receiver System/Spectrum Analyzer with built-in Amplifier Transient Limiter L.I.S.N. 12'x16'x12' RF Shielded Chamber Manufacturer Hewlett Packard Model No. HP 8546A Serial No. 3520A00248 Frequency Range 9KHz-5.6GHz, 50 Ohms

Hewlett Packard EMCO RF Shielding

11947A 3825/2 --

----

9 kHz ­ 200 MHz 10 dB attenuation 9 kHz ­ 200 MHz 50 Ohms / 50 µH --

6.4.4. Photos of test Setup
Please refer to Photos #1 and 2 in Annex 1 for details of test setup.

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 10 FCC ID: AFJ288000

6.4.5. Test Data
Conforms, Please refer to the Plots# 1 & 2 below for test results. UltraTech Group of Labs
Applicant: Product: Model: ICOM America Communications Receiver IC-R1500 AC POWER LINE CONDUCTED EMISSIONS MEASUREMENT PLOT Detector: [X] PEAK [X] AVERAGE Line Tested:1 [X] QUASI-PEAK Temp: 21°C Test Tech: Wayne Humidity:19%

Line Voltage :120VAC

Standard : FCC Part 15 Class B

Test Date: Dec 21, 2005 Comments: : AF Max Output

Plot # 1:

Si g n a l 1 2

F r e q ( MHz )

PK Amp

QP Amp

AV Amp 31. 8 19. 4

QP

L1 - 5. / 0

/ . 15/ / / / 0 0000 / . 33/ 450 0 0 /

66. 9 48. 8

61. / 0 41. 3

- 18. 1

ACT V DET : MEAS DET :

PEAK PEAK QP AVG MKR 1 5 0 k Hz / 65. 96 dB V

L OG 10 / d B/ AT N 10 dB /

REF 7 5 . / d B 0

V

VA SB SC F C A CORR ST ART 1 5 / k Hz 0 # I F BW 9 . / k Hz 0 AVG BW 3 / k Hz 0 ST OP 3 / . / / MHz 0 00 SW 1 . 4 / P 0 s ec

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 11 FCC ID: AFJ288000

UltraTech Group of Labs
Applicant: Product: Model: ICOM America Communications Receiver IC-R1500

AC POWER LINE CONDUCTED EMISSIONS MEASUREMENT PLOT Detector:[X] PEAK AVERAGE Line Tested:2 [X] QUASI-PEAK [X] Temp: 21°C Humidity:19%

Line Voltage :120VAC

Standard : FCC Part 15 Class B

Test Date: Dec 21, 2005 Comments: : AF Max Output Test Tech: Wayne

Plot # 2:

Si g n a l 1 2

F r e q ( MHz )

PK Amp

QP Amp

AV Amp 32. 1 19. / 0

QP

L1 - 4. 6

/ . 15/ / / / 0 0000 / . 333125 0

67. 3 47. 7

61. 4 40. 1 /

- 19. 4

ACT V DET : MEAS DET :

PEAK PEAK QP AVG MKR 1 5 0 k Hz / 66. 38 dB V

L OG 10 / d B/ AT N 10 dB /

REF 7 5 . 0 d B /

V

VA SB SC F C A CORR ST ART 1 5 0 k Hz / # I F BW 9 . / k Hz 0 AVG BW 3 / k Hz 0 ST OP 3 / . / / MHz 0 00 SWP 1 . 4 / 0 sec

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 12 FCC ID: AFJ288000

6.5.

RECEIVER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§15.111(a)]

6.5.1. Limits
Receivers that operate (tune) in the frequency range 30 to 960 Mhz and CB receivers that provides terminals for the connection of an external antenna may be tested to demonstrate compliance with the provisions of @ 15.109 with the antenna terminals shielded and terminated with a resistive termination equal to the impedance specified for the antenna, provided these receivers also comply with the following:- With the receiver antenna terminal connected to a resistive termination equal to the impedance specified or employed for the antenna, the power at the antenna terminal at frequency within the range from 30 Mhz to 5th harmonic of the highest frequency shall not exceed 2.0 nanowatts (or -57 dBm @ 50 Ohm).

6.5.2. Method of Measurements
Refer to Ultratech Test Procedures ULTR-P001-200 & ANSI C63.4 for method of measurements. The spectrum shall be investigated from the lowest radio frequency signal generated or used in the device, without going below the lowest frequency for which a radiated emission limit is specified, up to the frequency shown in the following table: Highest frequency generated or used in the device or on which the device operates or tunes (MHz) Below 1.705 1.705 - 108 108 ­ 500 500 -1000 Above 1000
th

Upper frequency of measurement range (MHz) 30 1000 2000 5000 5 harmonic of the highest frequency or 40 GHz, whichever is lower

6.5.3. Test Equipment List
Test Instruments Spectrum Analyzer/ EMI Receiver RF Signal Generator Manufacturer Rohde & Schawrz Hewlett Packard Model No. FSEK20/B4/B21 HP 83752B Serial No. 834157/005 3610A00457 Frequency Range 9 kHz ­ 40 GHz with external mixer 0.01 ­ 20 GHz

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 13 FCC ID: AFJ288000

6.5.4. Test Arrangement

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 14 FCC ID: AFJ288000

6.5.5. Test Data
Conforms. Please refer to Plot # 3 through # 7 for detailed measurement data. Remark: The FCC compliance requirements are exempted for receiver operating below 30 MHz and above 960 MHz. Therefore, tests will be performed at the receiver channel frequency of 30 MHz, 445.00 MHz and 960 MHz.

6.5.5.1.

Plot # 3 ­ Receiver Conducted Emissions @ 30 MHz

The emissions were scanned from 30 MHz to 1.0 GHz and all emissions found were more than 20 dB below the limits.

REF - 3 0 . 0 d Bm 1 0 d B/

AT T 0 d B

A_ v i e w B_ b l a n k

MKR 5 8 8 . 4 MHz

MARKER 5 8 8 . 4 MHz - 8 2 . 7 5 d Bm

REF OFS 0. 2 dB

RBW 1 0 0 k Hz VBW 3 0 0 k Hz SW P 2 0 0 ms ST ART 1 0 . 0 MHz ST OP 1 . 0 0 0 0 GHz

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 15 FCC ID: AFJ288000

6.5.5.2.

Plot # 4 ­ Receiver Conducted Emissions @ 445.00 MHz

The emissions were scanned from 30 MHz to 2.5 GHz and all emissions found were more than 20 dB below the limits.

REF - 3 0 . 0 d Bm 1 0 d B/

AT T 0 d B

A_ v i e w B_ b l a n k

MKR 2 5 1 . 8 MHz

MARKER 2 5 1 . 8 MHz - 8 7 . 8 1 d Bm

REF OFS 0. 2 dB

RBW 1 0 0 k Hz VBW 3 0 0 k Hz SW P 2 0 0 ms ST ART 1 0 . 0 MHz ST OP 1 . 0 0 0 0 GHz

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 16 FCC ID: AFJ288000

6.5.5.3.

Plot # 5 ­ Receiver Conducted Emissions @ 445 MHz

The emissions were scanned from 30 MHz to 2.5 GHz and all emissions found were more than 20 dB below the limits.

REF - 3 0 . 0 d Bm 1 0 d B/

AT T 0 d B

A_ v i e w B_ b l a n k

MKR 2 . 0 4 6 GHz

MARKER 2 . 0 4 6 GHz - 7 6 . 7 2 d Bm

REF OFS 0. 2 dB

RBW 1 MHz VBW 3 MHz SW P 5 0 ms ST ART 1 . 0 0 0 0 0 0 0 0 0 GHz ST OP 2 . 5 0 0 GHz

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 17 FCC ID: AFJ288000

6.5.5.4.

Plot # 6 ­ Receiver Conducted Emissions @ 960 MHz

The emissions were scanned from 30 MHz to 5 GHz and all emissions within 20 dB below the limits were recorded.

REF - 3 0 . 0 d Bm 1 0 d B/

ATT 0 d B

A_ v i e w B_ b l a n k MARKER 2 5 1 . 8 MHz

MKR 2 5 1 . 8 MHz
2

1

- 8 4 . 6 6 d Bm

RBW 1 0 0 k Hz VBW 3 0 0 k Hz SW 2 0 0 ms P START 1 0 . 0 MHz STOP 1 . 0 0 0 0 GHz

No . 1 : No . No . No . No . No . No . No . 2: 3: 4: 5: 6: 7: 8: :

* * * Mu l t i Ma r k e r 6 8 7 . 4 MHz 2 5 1 . 8 MHz

Li s t * * * - 7 6 . 0 3 d Bm - 8 4 . 6 6 d Bm

A A

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 18 FCC ID: AFJ288000

6.5.5.5.

Plot # 7 ­ Receiver Conducted Emissions @ 960 MHz

The emissions were scanned from 30 MHz to 5 GHz and all emissions within 20 dB below the limits were recorded.

REF - 3 0 . 0 d Bm 1 0 d B/

ATT 0 d B

A_ v i e w B_ b l a n k MARKER 1 . 3 7 7 GHz

MKR 1 . 3 7 7 GHz

1

23

4

- 7 0 . 7 5 d Bm

RBW 1 MHz VBW 3 MHz SW 6 0 ms P START 1 . 0 0 0 GHz STOP 5 . 0 0 0 GHz

No . 1 : No . No . No . No . No . No . No . 2: 3: 4: 5: 6: 7: 8: :

* * * Mu l t i Ma r k e r 1 . 3 7 7 GHz 2 . 7 6 0 GHz 2 . 8 0 6 GHz 3 . 4 5 7 GHz

Li s t * * * - 7 0 . 7 5 d Bm - 7 5 . 1 6 d Bm - 7 5 . 2 2 d Bm - 7 5 . 0 0 d Bm

A A A A

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 19 FCC ID: AFJ288000

6.6.

RECEIVER SPURIOUS/HARMONIC RADIATED EMISSIONS [§ 15.109(a)]

6.6.1. Limits
The equipment shall meet the limits of the following table: Test Frequency Range (MHz) 30 ­ 88 88 ­ 216 216 ­ 960 Above 960 Class B Limits @ 3 m (dBµV/m) 40.0 43.5 46.0 54.0 EMI Detector Used Quasi-Peak Quasi-Peak Quasi-Peak Average Measuring Bandwidth (kHz) RBW = 120 kHz, VBW > 120 kHz RBW = 120 kHz, VBW > 120 kHz RBW = 120 kHz, VBW > 120 kHz RBW = 1 MHz, VBW > 1 Hz

6.6.2. Method of Measurements
Refer to Ultratech Test Procedures ULTR-P001-200 & ANSI C63.4 for method of measurements. The spectrum shall be investigated from the lowest radio frequency signal generated or used in the device, without going below the lowest frequency for which a radiated emission limit is specified, up to the frequency shown in the following table: Highest frequency generated or used in the device or on which the device operates or tunes (MHz) Below 1.705 1.705 - 108 108 ­ 500 500 -1000 Above 1000 30 1000 2000 5000 5th harmonic of the highest frequency or 40 GHz, whichever is lower Upper frequency of measurement range (MHz)

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 20 FCC ID: AFJ288000

6.6.3. Test Equipment List
Test Instruments Spectrum Analyzer/ EMI Receiver Microwave Amplifier Biconilog Antenna Horn Antenna Manufacturer Rohde & Schawrz Hewlett Packard EMCO EMCO Model No. FSEK20/B4/B21 HP 83017A 3143 3155 1029 9701-5061 Serial No. 834157/005 Frequency Range 9 kHz ­ 40 GHz with external mixer 1 GHz to 26.5 GHz 20 MHz to 2 GHz 1 GHz ­ 18 GHz

6.6.4. Photos of test Setup
Please refer to Photos # 3 and 4 in Annex 1 for details of test setup

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 21 FCC ID: AFJ288000

6.6.5. Test Data
Remark: The FCC compliance requirements are exempted for receiver operating below 30 MHz and above 960 MHz. Therefore, tests will be performed at the receiver channel frequency of 30 MHz, 445 MHz and 960 MHz.

6.6.5.1.

Near Lowest Frequency (30 MHz)

The emissions were scanned from 30 MHz to 1 GHz and all emissions found were more than 20 dB below the limits.

6.6.5.2.

Near Middle Frequency (445 MHz)

The emissions were scanned from 30 MHz to 2.5 GHz and all emissions found were more than 20 dB below the limits.

6.6.5.3.

Near Highest Frequency (960 MHz)

The emissions were scanned from 30 MHz to 5 GHz and all emissions found were more than 20 dB below the limits.

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 22 FCC ID: AFJ288000

6.7.

RADIATED EMISSIONS FROM CLASS B UNINTENTIONAL RADIATORS (DIGITAL DEVICES) [§ 15.109(a)]

6.7.1. Limits
The equipment shall meet the limits of the following table: Test Frequency Range (MHz)
30 ­ 88 88 ­ 216 216 ­ 960 Above 960

Class B Limits @3m (dBµV/m)
40.0 43.5 46.0 54.0

EMI Detector Used
Quasi-Peak Quasi-Peak Quasi-Peak Average

Measuring Bandwidth (kHz)
RBW = 120 kHz, VBW > 120 kHz RBW = 120 kHz, VBW > 120 kHz RBW = 120 kHz, VBW > 120 kHz RBW = 1 MHz, VBW > 1 Hz

6.7.2. Method of Measurements
Refer to Ultratech Test Procedures ULTR-P001-200 & ANSI C63.4 for method of measurements. The spectrum shall be investigated from the lowest radio frequency signal generated or used in the device, without going below the lowest frequency for which a radiated emission limit is specified, up to the frequency shown in the following table: Highest frequency generated or used in the device or on which the device operates or tunes (MHz) Below 1.705 1.705 - 108 108 ­ 500 500 -1000 Above 1000 30 1000 2000 5000 5th harmonic of the highest frequency or 40 GHz, whichever is lower Upper frequency of measurement range (MHz)

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 23 FCC ID: AFJ288000

6.7.3. Test Equipment List
Test Instruments Spectrum Analyzer/ EMI Receiver Microwave Amplifier Biconilog Antenna Horn Antenna Manufacturer Rohde & Schawrz Hewlett Packard EMCO EMCO Model No. FSEK20/B4/B21 HP 83017A 3143 3155 1029 9701-5061 Serial No. 834157/005 Frequency Range 9 kHz ­ 40 GHz with external mixer 1 GHz to 26.5 GHz 20 MHz to 2 GHz 1 GHz ­ 18 GHz

6.7.4. Photos of test Setup
Please refer to Photos # 3 and 4 in Annex 1 for details of test setup

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 24 FCC ID: AFJ288000

6.7.5. Test Data
FREQUENCY (MHz) 57.50 110.00 162.80 E-FIELD @3m (dBuV/m) 24.9 25.1 30.3 DETECTOR USED (PEAK/QP) PEAK PEAK PEAK ANTENNA PLANE (H/V) V H V LIMIT @3m (dBuV/m) 40.0 43.5 43.5 MARGIN (dB) -15.1 -18.4 -13.2 PASS/ FAIL PASS PASS PASS

The emissions were scanned from 30 MHz to 1000 MHz at 3 Meters distance and all emissions within 20 dB below the limits were recorded.

Radiated Emissions Measurments @ 3m OFTS ICOM Communication Receiver, IC-R1500
70

60

Radiated Emissions @ 3m (dBuV/m)

50

40

30

20

10

0 10 100 Frequency (MHz) 1000 10000

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 25 FCC ID: AFJ288000

6.8.

REQUIREMENTS FOR SCANNING RECEIVERS [47 CFR 15.121]

6.8.1. FCC Rules
a. Except as provided in paragraph (c) of this section, scanning receivers and frequency converters designed or marketed for use with scanning receivers, shall:
(1)

Be incapable of operating (tuning), or readily being altered by the user to operate, within the frequency bands allocated to the Cellular Radiotelephone Service in part 22 of this chapter (cellular telephone bands). Scanning receivers capable of ``readily being altered by the user'' include, but are not limited to, those for which the ability to receive transmissions in the cellular telephone bands can be added by clipping the leads of, or installing, a simple component such as a diode, resistor or jumper wire; replacing a plug-in semiconductor chip; or programming a semiconductor chip using special access codes or an external device, such as a personal computer. Scanning receivers, and frequency converters designed for use with scanning receivers, also shall be incapable of converting digital cellular communication transmissions to analog voice audio. Be designed so that the tuning, control and filtering circuitry is inaccessible. The design must be such that any attempts to modify the equipment to receive transmissions from the Cellular Radiotelephone Service likely will render the receiver inoperable.

(2)

b. Except as provided in paragraph (c) of this section, scanning receivers shall reject any signals from the Cellular Radiotelephone Service frequency bands that are 38 dB or lower based upon a 12 dB SINAD measurement, which is considered the threshold where a signal can be clearly discerned from any interference that may be present. c. Scanning receivers and frequency converters designed or marketed for use with scanning receivers, are not subject to the requirements of paragraphs (a) and (b) of this section provided that they are manufactured exclusively for, and marketed exclusively to, entities described in 18 U.S.C. 2512(2), or are marketed exclusively as test equipment pursuant to Sec. 15.3(dd)

d. Modification of a scanning receiver to receive transmissions from Cellular Radiotelephone Service frequency bands will be considered to constitute manufacture of such equipment. This includes any individual, individuals, entity or organization that modifies one or more scanners. Any modification to a scanning receiver to receive transmissions from the Cellular Radiotelephone Service frequency bands voids the certification of the scanning receiver, regardless of the date of manufacture of the original unit. In addition, the provisions of Sec. 15.23 shall not be interpreted as permitting modification of a scanning receiver to receiver Cellular Radiotelephone Service transmissions. e. Scanning receivers and frequency converters designed for use with scanning receivers shall not be assembled from kits or marketed in kit form unless they comply with the requirements in paragraph (a) through (c) of this section.

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 26 FCC ID: AFJ288000

f.

Scanning receivers shall have a label permanently affixed to the product, and this label shall be readily visible to the purchaser at the time of purchase. The label shall read as follows: WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

(3)

``Permanently affixed'' means that the label is etched, engraved, stamped, silkscreened, indelible printed or otherwise permanently marked on a permanently attached part of the equipment or on a nameplate of metal, plastic or other material fastened to the equipment by welding, riveting, or permanent adhesive. The label shall be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable. The label shall not be a stick-on, paper label. When the device is so small that it is not practicable to place the warning label on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user and shall also be placed on the container in which the device is marketed. However, the FCC identifier must be displayed on the device.

(4)

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 27 FCC ID: AFJ288000

6.8.2. Declaration for Compliance with FCC §15.121
· Comply with FCC 121(a)(1) ­ This Scanning Receiver is incapable of operating (tuning), or readily being altered by the user to operate, within the frequency bands allocated to the Cellular Radiotelephone Service in part 22 of this chapter (cellular telephone bands). Please refer to manufacturer's declaration for compliance with this Rule. · Comply with FCC 121(a)(2) ­ This Scanning Receiver is designed so that the tuning, control and filtering circuitry is inaccessible. The design is such that any attempts to modify the equipment to receive transmissions from the Cellular Radiotelephone Service likely will render the receiver inoperable. Please refer to manufacturer's declaration for compliance with this Rule. · Comply with FCC 121(b) ­ Please refer to the following Section of this Test Report for Scanning Receivers Cellular Band Rejection test. Comply with FCC 121(c) ­ Not applicable. Comply with FCC 121(d) ­ The Users Manual of this Scanning Receiver is provided with the Warning statement as below:

· ·

Warning: Changes or modifications not expressly approved by ICOM Incorporated could void the user's authority to operate the equipment. · · Comply with FCC 121(e) ­ This Scanning Receiver will not be assembled from kits or marketed in kit form. Comply with FCC 121(f) ­ This Scanning Receiver has a label permanently affixed to the product and this label is readily visible to the purchaser at the time of purchase. The label reads as follows: WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 28 FCC ID: AFJ288000

6.9.

SCANNING RECEIVERS CELLULAR BAND REJECTION [47 CFR 15.121(b)]

6.9.1. Limits
Except as provided in paragraph (c) of this section, scanning receivers shall reject any signals from the Cellular Radiotelephone Service frequency bands that are 38 dB or lower based upon a 12 dB SINAD measurement, which is considered the threshold where a signal can be clearly discerned from any interference that may be present.

6.9.2. Method of Measurements
(1) (2) (3) (4) (5) Connected the EUT as shown in the following block diagram Apply a standard RF signal to the receiver input port Adjust the audio output signal of the receiver to it's rated value with the distortion less than 10% Adjust the RF Signal Generator Output Power to produce 12 dB SINAD without the audio output power dropping by more than 3 dB Repeat step (4) at lowest, middle and highest channel frequencies across all cellular base station band to establish a reference sensitivity level. The reference sensitivity taken was the lowest or worse-case sensitivity for all of the bands. Adjust the RF Signal Generator output to a level of +60 dB above the reference sensitivity obtained in step (5) Set the Receiver squelch threshold (the signal required to open the squelch) no greater than +20 dB above the reference sensitivity level. Put the receiver in a scanning mode and allow it to scan across it's complete receive range If the receiver unsquelched or stopped on any frequency, the display frequency is recorded. The signal generator output level was then adjusted until 12 dB SINAD from the receiver was produced. The signal generator level associated with this response was also noted. Repeat this procedure for 3 frequencies in the cellular base station transmit band. The difference between the signal generator output for any response recorded and reference sensitivity is the rejection ratio

(6) (7) (8) (9)

(10) (11)

RF Signal Generator

EUT

Distortion Analyzer

RF Signal Generator

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 29 FCC ID: AFJ288000

6.9.3. Test Equipment List
Test Instruments Distortion analyzer RF Signal Generator RF Signal Generator Manufacturer Hewlett-Packard Fluke Fluke Model No. 8903E 6061A 6061A Serial No. 3514A0146 0 4770301 5130586 Frequency Range 20-100K Hz 10 kHz ­ 1050 MHz 10 kHz ­ 1050 MHz

6.9.4. Test Data

6.9.4.1.

EUT's Operating Mode: FM
Cellular Transmitter Test Frequencies (MHz) RF Input Signal Level @ Cellular Frequencies for 12 dB SINAD (dBm) Reference Sensitivity dBm Rejection Ratio (dB) Maximum Rejection Ratio Limit (dB)

EUT's Scanning Frequency Band (MHz)

824.04, 836.40, 848.97, 869.04, -40.0 -90 to -124 <-50 -38.0 880.62, 893.97 There is no spurious response detected within the above frequency band with the Rejection Ratio of at least -50 dB. 28.00 ­ 3000

6.9.4.2.

EUT's Operating Mode: AM
Cellular Transmitter Test Frequencies (MHz) RF Input Signal Level @ Cellular Frequencies for 12 dB SINAD (dBm) Highest Reference Sensitivity Rejection Ratio (dB) Maximum Rejection Ratio Limit (dB)

EUT's Scanning Frequency Band (MHz)

dBm 824.04, 836.40, 0.495 ­ 1299.99 848.97, 869.04, -30.0 -89 to -110 <-59 -38.0 880.62, 893.97 There is no spurious response detected within the above frequency band with the Rejection Ratio of at least -59 dB.

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 30 FCC ID: AFJ288000

6.9.4.3.

EUT's Operating Mode: WFM
Cellular Transmitter Test Frequencies (MHz) RF Input Signal Level @ Cellular Frequencies for 12 dB SINAD (dBm) Highest Reference Sensitivity Rejection Ratio (dB) Maximum Rejection Ratio Limit (dB)

EUT's Scanning Frequency Band (MHz)

dBm 824.04, 836.40, 50.00 ­ 3000 848.97, 869.04, -40.0 -89 to -114 <-49 -38.0 880.62, 893.97 There is no spurious response detected within the above frequency band with the Rejection Ratio of at least -49 dB.

6.9.4.4.

EUT's Operating Mode: SSB
Cellular Transmitter Test Frequencies (MHz) RF Input Signal Level @ Cellular Frequencies for 12 dB SINAD (dBm) Highest Reference Sensitivity Rejection Ratio (dB) Maximum Rejection Ratio Limit (dB)

EUT's Scanning Frequency Band (MHz)

dBm 824.04, 836.40, 0.495 ­ 1299.999 848.97, 869.04, -30.0 -98 to -106 <-68 -38.0 880.62, 893.97 There is no spurious response detected within the above frequency band with the Rejection Ratio of at least -68 dB.

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 31 FCC ID: AFJ288000

EXHIBIT 7.

MEASUREMENT UNCERTAINTY

The measurement uncertainties stated were calculated in accordance with the requirements of NIST Technical Note 1297 and LAB 34

7.1.

LINE CONDUCTED EMISSION MEASUREMENT UNCERTAINTY
CONTRIBUTION (Line Conducted) PROBABILITY DISTRIBUTION Rectangular Rectangular Normal (k=2) U-Shaped Std. deviation -Normal Normal (k=2) UNCERTAINTY (dB) 9-150 kHz 0.15-30 MHz +1.5 +1.5 +1.5 +1.5 +0.3 +0.5 +0.2 +0.2 -+1.25 +2.50 +0.3 +0.05 -+1.30 +2.60

EMI Receiver specification LISN coupling specification Cable and Input Transient Limiter calibration Mismatch: Receiver VRC 1 = 0.03 LISN VRC R = 0.8(9 kHz) 0.2 (30 MHz) Uncertainty limits 20Log(1+1R) System repeatability Repeatability of EUT Combined standard uncertainty Expanded uncertainty U

Sample Calculation for Measurement Accuracy in 150 kHz to 30 MHz Band: uc(y) = mui2(y) = + (1.52 + 1.52)/3+ (0.5/2) 2 + (0.05/2) 2+0.352 = + 1.30 dB
I=1

U = 2uc(y) = + 2.6 dB

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)

FCC PART 15, SUBPART B, SCANNING RECEIVERS SCANNING RECEIVER, Model IC-R1500 & IC-PCR1500

Page 32 FCC ID: AFJ288000

7.2.

RADIATED EMISSION MEASUREMENT UNCERTAINTY
CONTRIBUTION (Radiated Emissions) PROBABILITY DISTRIBUTION Normal (k=2) Normal (k=2) Rectangular Rectangular Rectangular Rectangular Rectangular Rectangular Rectangular U-Shaped Std. Deviation Normal Normal (k=2) UNCERTAINTY (+ dB) 3m 10 m +1.0 +1.0 +0.3 +0.5 +1.5 +1.5 +0.5 +0.5 +2.0 +0.5 0.0 +0.2 +0.25 +0.25 +0.6 +0.4 +2.0 +2.0 +1.1 +0.5 -1.25 +0.5 +0.5 +2.19 / -2.21 +1.74 / -1.72 +4.38 / -4.42 +3.48 / -3.44

Antenna Factor Calibration Cable Loss Calibration EMI Receiver specification Antenna Directivity Antenna factor variation with height Antenna phase center variation Antenna factor frequency interpolation Measurement distance variation Site imperfections Mismatch: Receiver VRC 1 = 0.2 Antenna VRC R = 0.67(Bi) 0.3 (Lp) Uncertainty limits 20Log(1+1R) System repeatability Repeatability of EUT Combined standard uncertainty Expanded uncertainty U

Calculation for maximum uncertainty when 3m biconical antenna including a factor of k = 2 is used: U = 2uc(y) = 2x(+2.19) = +4.38 dB And U = 2uc(y) = 2x(-2.21) = -4.42 Db

ULTRATECH GROUP OF LABS
3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: 905-829-1570, Fax. : 905-829-8050

File #: ICOM-122FCC15B
January 10, 2006

All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST)