Text preview for : acc-164.pdf part of CANON acc-164 CANON Copiers GP 605 ServBull ServBullGP405 acc-164.pdf
Back to : acc-164.pdf | Home
Service Bulletin COPIER
Issued by Canon Europa N.V.
Model : Network Interface Kit-TR4 No.: Acc-164
(FF-T01-B3-000025-01)
DATE: 09.07.99
Location : NETWORK INTERFACE KIT-TR4
Subject : NETWORK INTERFACE KIT-TR4 INSTALLATION PROCEDURE (NETWORK MULTI-PDL
PRINTER BOARD-H1/NETWORK PRINTER BOARD-K1)
Reason : This bulletin provides instructions for installing the Network Interface Kit-TR4 to the Network Multi-
PDL Printer Board-H1/Network printer Board-K1.
Details : The pages that follow describe how the Network Interface Kit-TR4 may be installed. The product is an
accessory designed in common for the following printer boards; see the respective Service Information
bulletins for installation procedures.
Network Multi-PDL Printer Board-D1/Network Printer Board-E1 (Service Bulletin Acc-162)
Network Multi-PDL Printer Board-H1/Network Printer Board-K1 (this bulletin)
Network Printer Board-F1 (Service Bulletin Acc-163)
-1/5-
Acc-164
Network Interface Kit-TR4 Installation Procedure
1 Points to Note during Installation
Before turning off the main power, be sure to check that the FAX memory lamp is NOT on.
Copying
Error Error Data Error
COPY FAX PRINTI/F
Memory
TX/RX
Fig. 1
2 Installation Procedure
A. Checking the Package contents
Network Interface Kit-TR4 1pc.
Fig. 2-1
-2/5-
Acc-164
B. Removing the Network Interface Kit-TR4 7) Remove the three screws.
1) Turn off the main power. Screws
2) Remove the two screws, and detach the PDL
cover.
PDL cover
Fig. 2-5
Screws
8) While holding up the network printer unit with
both your hands, free the upper left hook to detach
the network printer unit from the copier.
Fig. 2-2
Hook
3) Remove the four screws, and detach the rear
cover.
4) Remove the three screws, and detach the flywheel.
5) Remove the two screws, and detach the cable
cover.
Network printer
Cable cover board
Screws
Fig. 2-3
Fig. 2-6
6) Disconnect the two flat cables on the printer board
side; then, disconnect the power connector.
C. Mounting the Network Interface Kit-TR4
1) Remove the twelve screws, and detach the
upper cover of the network printer unit.
Power connector Flat cable
Fig. 2-4
Fig. 2-7 -3/5-
Acc-164
2) Remove the two screws, and detach the TR4 5) Mount the upper cover of the network printer unit
dressing cover. with twelve screws. (See Fig. 2-7.)
D. Mounting the Network Interface Kit-TR4
1) Remove the screws (at the bottom) used to
TR4 dressing secure the copier's left cover, and free the left
cover cover toward the outside.
Screws
Fig. 2-8 Left cover
Fig. 2-11
3) Detach the connector cover, and insert the
Network Interface Kit-TR4.(Be sure to orient it as 2) While holding the network printer unit with both
shown in the figure.) your hands, insert the lower right hook into the
copier.
Connector cover Network printer unit
Hook
Network Interface
Fig. 2-12
Kit-TR4
Fig. 2-9 3) Fit the hook in the upper left of the unit to the
copier.
4) Fit the two screws, removed previously from the
Hook
dressing plate side of the network printer board;
then, secure the Network Interface Kit-TR4 in
place to the printer unit.
Fig. 2-13
4) Fit the three screws. (See Fig. 2-5.)
5) Connect the two flat cables and the power
Screws connector. (See Fig. 2-4.)
6) Mount the cable cover (See Fig. 2-3.), flywheel,
left cover, and rear cover.
7) Mount the PDL dressing cover with two
screws. (See Fig. 2-2.)
Fig. 2-10
-4/5-
Acc-164
3 Setting the Network Interface Kit-TR4
When you have finished mounting the Network Interface Kit-TR4, be sure to request the
administrator of the user's network to perform the following:
By referring to the Administrator's Guide, make necessary settings for the Network Interface
Kit-TR4.
-5/5-