Text preview for : DPS-24.pdf part of Akai DPS-24 Akai DPS DPS-24 DPS-24.pdf
Back to : DPS-24.pdf | Home
48V ON OFF
1 2 3 4 5 6 7 8 9 10 11 12
A/B
A B A B A B A B A B A B A B A B A B A B A B A B
LINE
/ MIC
LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC
1 2 3 4 5 6 7 8 9 10 11 12 MONITOR
TRIM LEVEL
Q1
0 +60 0 +60 0 +60 0 +60 0 +60 0 +60 0 +60 0 +60 0 +60 0 +60 0 +60 0 +60 MIN MAX
-15 +45 -15 +45 -15 +45 -15 +45 -15 +45 -15 +45 -15 +45 -15 +45 -15 +45 -15 +45 -15 +45 -15 +45 CLIP Q2
0
2
SIGNAL / CLIP SIGNAL / CLIP SIGNAL / CLIP SIGNAL / CLIP SIGNAL / CLIP SIGNAL / CLIP SIGNAL / CLIP SIGNAL / CLIP SIGNAL / CLIP SIGNAL / CLIP SIGNAL / CLIP SIGNAL / CLIP !!SOLO!! 4
6
8 Q3
10
RECORD 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 1 10 2 11 3 12 4 2-TRACK 15
/EDIT 20
25 Q4
SELECT 30
35
40
50
13 5 14 6 15 7 16 8 17 1 18 2 19 3 20 4 21 5 22 6 23 7 24 8 MONO 60 Q5
L R
Q6
L/R 1/2 3/4 5/6 7/8 Q-STRIP PAN FX / AUX 1 FX / AUX 2 FX / AUX 3 FX / AUX 4 NEAR
ASSIGN FUNCTION
Q-CHANNEL EQ ON PRE PRE PRE PRE
F1 F2 F3 F4 F5 F6
LOCK
RELEASE
STUDIO CR
HOURS MINS SECS FRAMES
DISPLAY
SELECT
L R 20Hz 20kHz -24dB +24dB 20Hz 20kHz -24dB +24dB Q 20Hz 20kHz -24dB +24dB FX / AUX 1 FX / AUX 2 FX / AUX 3 FX / AUX 4
PAN LOW SWEEP HIGH EFFECT / AUX SENDS TB
BARS BEATS CLOCKS CONTRAST
LEVEL
SELECT
SELECT
CURSOR
TALK BACK
ON EXT MAIN
SYNC SCREEN EDIT MIXER AUTOMATE FX PROJECT SETUP
SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO
OFFSET GRID DSP PATCH V.TRACK CD-R
ZOOM
INPUT 1 2 3 4 5 6 7 8 9 10 11 12
MASTER MIX SCENE
TRACK 1 / 13 2 / 14 3 / 15 4 / 16 5 / 17 6 / 18 7 / 19 8 / 20 9 / 21 10 / 22 11 / 23 12 / 24
STORE RECALL 7 8 9
SHIFT UNDO REDO PRE-ROLL AUTO
4 5 6
CANCEL ENTER
SET
1 2 3
FADER BANK
INP TRACKS TRACKS GROUP USER
1-12 1-12 13-24 FX BANK INP MON WHEEL
- + 0
IN OUT
TO FROM IN OUT AUTO LOCATE JOG SHUTTLE
GO TO MEMORY
OVER LOOP
REWIND FAST FORWARD STOP
5 5
ABORT
GROUP 1 GROUP 2 GROUP 3 GROUP 4 GROUP 5 GROUP 6 GROUP 7 GROUP 8 FX RTN 1 FX RTN 2 FX RTN 3 FX RTN 4 L/R
DIGITAL PERSONAL STUDIO
SERVICE MANUAL
1
Downloaded from www.Manualslib.com manuals search engine
# SAFETY INSTRUCTIONS # INFORMATIONS
1. Parts identified by the } symbol are critical for safety. SYMBOLS FOR PRIMARY DESTINATION
Replace them only with the parts number specified. Unit destinations are indicated with letters as shown below.
2. In addition to safety, other parts and assemblies are
specified for conformance with such regulations as those Symbols Principal Destinations
applying to spurious radiation. A U.S.A
These must also be replaced only with the specified B England
replacements. E Europe
Examples : Noise blocking capacitors, noise blocking filters, J Japan
etc. V Germany
3. Use specified internal wiring. Note especially : X1 Japan
1) Wires covered with PVC tubing
X4 Universal Area
2) Double insulated wires
3) High voltage leads
4. Use specified insulating materials for hazardous live parts.
Note especially : MAKE YOUR CONTRIBUTION TO PROTECT THE
1) Insulation Tape ENVIRONMENT
2) PVC tubing Used batteries with the ISO symbol for recycling as
3) Spacers (insulating barriers) well as small accumulators (rechargeable batteries),
4) Insulation sheets for transistors mini-batteries (cells) and starter batteries should not
5) Plastic screws for fixing micro switches be thrown into the garbage can.
Please leave them at an appropriate depot.
5. When replacing AC primary side components (trans-
formers, power cords, noise blocking capacitors, etc.), wrap
the ends of the wires securely around the terminals before PRECAUTIONS FOR LITHIUM BATTERY
soldering. The lithium battery may explode when incorrectly replaced.
[OBSERVE THE FOLLOEING WHEN REPLACING]