Text preview for : 2K3-005.pdf part of Kyocera 2K3-005 Kyocera Printer FS-6025-6030MFP SERVICEBULLETINS 2K3-005.pdf
Back to : 2K3-005.pdf | Home
Service Bulletin
SB Number: SB 2K3-005 Creation Date: 18/05/2011
Subject: Firmware upgrade (Pack v2.00)
Model: FS-6025MFP/6025MFP(B)/6030MFP
Content of changes
1. Paper jam 5001 (Bridge conveying sensor 3 non arrival jam) may occur.
2. Added U605 [Data clear].
3. Black streaks after setting magnification by U065.
4. The default screen lay-out of the favorites has been changed.
5. Added U265 [Set Model Destination].
6. Added support for the customized operation panel.
7. Registered data may not be found at the address book.
8. Error code F56B may occur.
Firmware
Type Program No. Version
Upgrade Pack Ver. 2K3_V2.00 2.00
MAIN 2K3_2F00.002.351 002.351
MMI 2K3_7000.002.347 002.347
ENGINE 2K3_1000.005.002 005.002
IO 2K3_1E00.001.010 001.010
DP 3M8_9500.003.001 003.001
FAX BOOT/APL 5JR_5500.B02.001 B02.001
Firmware notes *: BOOT: B01.019 / APL: B01.019
Classification Entire stock rework In-field modification at next visit X No modification necessary
In-field modification by case
Field measure When the above mentioned phenomena occur, please upgrade the firmware to the latest version.
Serial numbers of affected machines
Type Serial number
FS-6025MFP/6025MFP(B)/6030MFP April 2011 production.
The above mentioned changes have been applied to machines produced after the above mentioned production date.
KMIS Service Department, Kyocera Mita Europe Page 1 of 3 B124 / SB 2K3-005
Service Bulletin
Item Contents
1 Paper jam 5001 (Bridge Phenomenon
conveying sensor 3 non Paper jam 5001 (Bridge conveying sensor 3 non arrival jam) may occur, when
arrival jam) may occur. operating the FS-6025MFP with the DF-470 and the AK-470 installed (Optional
paper feeder is not installed).
Cause
The switch at the conveying sensor 2 may vibrate, so this sensor is triggered.
The machine detects this as if the next sheet of paper has arrived. Due to the
jam detection time-out, the above mentioned paper jam may occur. This is the
case when continuously printing A4 widthwise from the standard paper cassette
and when ejecting to the DF-470.
Solution
The timing for contact bounce has been changed from 20 milliseconds to 200
milliseconds.
Conveying sensor 2
2 Added U605 [Data clear]. Maintenance mode U605 [Data clear] has been added.
3 Black streaks after setting Black streaks may appear on the B/W copy after enlarging with maintenance
magnification by U065. mode U065 [Adjusting the scanner magnification]
4 The default screen lay-out The lay-out of the buttons from the default screen of the favorites has been
of the favorites has been changed.
changed.
5 Added U265 [Set Model Maintenance mode U265 [Set Model Destination] has been added.
Destination].
6 Added support for the Customized operation panel is available by using workflow templates in
customized operation panel. combination with FMU (File Management Utility).
7 Registered data may not be The message "Not registered" may appear when searching the address book for
found at the address book. registered data.
8 Error code F56B may occur. System error code F56B may occur under the below mentioned conditions, when
scanning large sized originals to a smaller sized scan.