Text preview for : ATA1192.pdf part of SIGMA Mouse ATA1092XA, MA60H161B Schematic Diagram ( Data Sheet ) Optical Mouse Sensor IC + MCU - Version 1_6 - ATA1080XA - pag. 11



Back to : ATA1192.pdf | Home

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

OPTICAL MOUSE SENSOR IC
ATA1092XA
(ATA1080XA+ Mosart MA60H161B)

Version 1_6

Notice AT Lab, Inc. ("@Lab") reserves the right to change any products described herein at any time and without notice. @Lab assumes no responsibility or liability arising from the use of the products described herein, except as expressly agreed to in writing by @Lab. The use and purchase of this product does not convey a license under any patent rights, copyrights, trademark rights, or any other intellectual property rights of @Lab. Copyright 2003, AT Lab, Inc. All rights reserved.

Page 1 / 11

Sep. 2003

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

@Lab ATA1092XA Optical Mouse Sensor Data Sheet

INTRODUCTION
Description The ATA1092XA is an optical sensor with capability of replacing current track ball mouse of computer system. How the most common optical sensor for mouse works today is: The sensor captures "snapshots" of the work surface at 1,700 (or 3,400) times per second, then the captured images are sent to an arithmetic unit to determine direction and magnitude of movement in accordance with speed and acceleration.

However, the key differences in ATA1092XA from other optical sensors are that it is designed based on a system level architecture so that it can eliminate side parts resulting in saving extra manufacturing costs. Additionally, ATA1092XA includes Mosart's MCU (MA60H161B) within one package so that no additional MCU is needed. ATA1092XA also tolerates to all different magnitudes of movement so that the sensor can be used for design purpose where accuracy is the most important factor as well as for gaming purpose where speed would be the critical factor.

The sensor is in a 24-pin optical DIP package with external OSC pin so that the sensor can be modified to run at 12 MHz in the application. ATA1092XA comes with the "default" resolution of 400 counts per inch (cpi) and the rate of motion up to 12.75 inches per second, running at 6 MHz. Furthermore, with 12 MHz OSC, one can enhance the resolution electrically up to 600 cpi with the rate of motion up to 19 inches per second ("Fast")

Page 2 / 11

Sep. 2003

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

General Features Optical navigation technology No mechanical parts High reliability Complete 2-D motion sensor High speed motion detection Proprietary enhanced navigation accuracy over a wide variety of surfaces No precision optical alignment Single 5.0 volt power supply Low operation current USB or PS/2 interface is included Power Conservation Mode during times of no movement (No Motion). No additional MCU is needed.

MA60H161B's Features inside ATA1092. USB-PS/2 Auto-Detection Circuit. 5V -> 3.3V Regulator. XA,XB,YA,YB,ZA,ZB Auto-Reference Circuit. 120Khz Ring Oscillator. Compatible with PS/2 protocol. Conforms to USB 1.5Mbps Specification, Version 1.1. Integrated USB transceiver. Built-in 1.5Kohm D- pull-high resistor. Compatible with Microsoft scrolling mouse. Built-in error detection circuit(one way). Sampling rate of motion detector is 50Khz. Both Key-press and key-release de-bounce internal is about 13.6ms. 3 Button ( Left, Middle, Right ) application

Applications Mice for desktop PC's, Workstations, and notebook PC's Trackballs Integrated input devices

Page 3 / 11

Sep. 2003

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

Top View of ATA1092XA

Pinout Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Name Nreset DVDD XYLED DGND YA Wh2 Wh1 XIR GND LB RB VD1 DD+ OSCI OSCO VDD Test XB MB XA OSC AGND AVDD Type Input Power Output Ground Output Input Input Output Ground Input Input Power Bidir Bidir Input Output Power Input Output Input Output Input Ground Power Description Reset Power (5V) LED On/Off Ground YA Output Wheel 2 Wheel 1 Power Down Ground Left Button Right Button Power ( 5V) Data Minus Data Plus Oscillator/Clock Oscillator/Clock Power(3.3V) Test XB Output Middle Button XA Output Sensor Oscillator/Clock Ground Power (5V)

Note: Pin assignments can be altered without notice

Page 4 / 11

Sep. 2003

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

ELECTRICAL CHARACTERISTICS
Parameter Absolute Maximum Ratings
Storage Temperature Operating Temperature Supply Voltage Input Voltage ESD Tstg Topr Vdd Vin °C °C V V V -20 0 -0.5 Vss-0.3 200 2000 70 50 7.0 Vdd+0.3 All pins, machine model All pins, human body model

Symbol

Unit

Min.

Typ.

Max.

Note

Recommended Operating Conditions
Operating Temperature Supply Voltage System clock (OSCI) Sensor clock (OSC) Frequency Distance from lens reference plane to surface Speed Topr Vdd Fclk Sclk D S °C V Mhz Mhz mm Inch/sec 2.0 0 4.5 25 5.0 6 6 12 2.2 2.4 12.75 Default (400cpi) 40 5.5 Default (400cpi) Fast Move(option)

AC Electrical Specification (Recommended operating conditions: Temp=25°C, Vdd=5.0V, and CLK=6MHz)
Motion Scale Factor Response Time (Default) Response Time (Fast) Power-On Reset Trsp1 Tres counts /sec msec msec 8.7 4.35 300 400 10.9 5.45 426 13.1 6.55 500 Default (400cpi) Movement to data in no motion mode.

DC Electrical Specification (Recommended operating conditions: Temp=25C and Vdd=5.0V)
Supply Current (in Motion) Supply Current (No Motion) Input Low Voltage Input High Voltage OSC Input Low Voltage OSC Input High Voltage Output Low Voltage (LED) Output High Current (LED) Idd Idd1 VIL VIH VOIL VOIH VOLL IOHLED mA mA V V V V V mA 2.0 3.5 1.5 16 4 0.3 4 20 8 0.8 1.5 0.5 6.5 Default Default

Page 5 / 11

Sep. 2003

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

TYPICAL APPLICATION

Application circuit for ATA1092XA running at 6MHz

C0 100nF J1 VDD D-/DATA D+/CLOCK GND F1 BEAD JUMP 1 2 3 4 CON4 D-/DATA D+/CLOCK F2 F3 BEAD JUMP BEAD JUMP

VDD Q3 A733-Y

C2 0.22uF SNS1 1 2 R10 22k 3 C5 100nF 4 5 6 7 8 NRST DVDD XY_LED DGND YA Wh2 Wh1 XIR GND LB RB VD1

R9 100k

ATA1092X AVDD AGND OSC XA MB XB TEST VDD OSCO OSCI D+ DD1 24 23 22 21 20 19 18 C8 17 100uF 16 15 14 13 MB1 2

C4 100nF C3 100uF

WH1 C1 100nF 1 2 3 M_WHEEL LB1 1 RB1 1 2 2

1

C6 33P X1 6.0M C7 33P

9 10 11 12

R3 68

Q1 R4 33k R5 33k NPN CBE

LED

GND

Page 6 / 11

Sep. 2003

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

Application Circuit for ATA1092XA running at 12MHz

C0 100nF J1 VDD D-/DATA D+/CLOCK GND F1 BEAD JUMP 1 2 3 4 CON4 D-/DATA D+/CLOCK F2 F3 BEAD JUMP BEAD JUMP

EXTERNAL 12MHz OPTION

VDD Q3 A733-Y R8 100

F4 BEAD JUMP

C2 0.22uF

R9 100k

SNS1 1 2 R10 22k WH1 C1 100nF 1 2 3 M_WHEEL 8 LB1 1 RB1 1 2 12 2 10 11 9 3 C5 100nF 4 5 6 7 NRST DVDD XY_LED DGND YA Wh2 Wh1 XIR GND LB RB VD1

ATA1092X AVDD AGND OSC XA MB XB TEST VDD OSCO OSCI D+ DD1 24 23 22 21 20 19 18 C8 17 100uF 16 15 14 13 MB1 2

C4 100nF C3 100uF

C10 100nF

C11 100nF

R7 100k Q2 C945-Y

C12 33p 1 C9 22pF C6 33P X2 R6 1k 12M

X1 6.0M

C7 33P

R3 68

Q1 R4 33k R5 33k NPN CBE

LED

GND

Page 7 / 11

Sep. 2003

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

OPERATIONS
Theory of Operation

LED Lens IAS Pixel Array (18 x 18) Surface Moving Calculation Numerating Focusing Photo Current Generating ADC MVF Quad. Moving Data Output ATA1080

ATA1092XA is based on Optical Navigation Technology. It contains an Image Acquisition System (IAS), a Motion Vector Finding Processor (MVFP), a two-channel quadrature output.

The IAS acquires microscopic surface images via the lens and illumination system provided by other parts. These images are processed by the MVF processor to determine the direction and distance of motion. The MVF processor generates the x and y relative displacement values that are converted into two-channel quadrature signals.

Description of Operation Once power is up, it requires 75.3 msec to be stabilized in Motion mode. In order to minimize the power consumption, when there is no motion in the sensor, ATA1092XA turns its operation into nomotion mode. That is, when there is no motion for one second (default time period) in Motion mode, ATA1092XA turns into No-Motion mode.

In default, from No-Motion mode, ATA1092XA wakes up every 10.9 msec for one report time (588 msec) and compares with the previous wake-up in order to check whether there is any movement. Likewise in fast mode (600 cpi running at 12 MHz), from No-Motion state, ATA1092XA wakes up every 5.45 msec for one report time (294 msec) and compares with the previous wake-up to check if there is any movement.

Page 8 / 11

Sep. 2003

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

Timing in No-Motion Mode

response time 1 (10.9 msec in detault) (5.45 msec in fast mode)

W ake-up tim e = 588 µ sec (1/1700 sec) in default = 294 µ sec (1/3400 sec) in fast m ode (600cpi@ 12MHz) Only added LED on tim e = 588 µ sec (1/1700 sec) in default = 294 µ sec (1/3400 sec) in fast m ode =>> No wake-up tim e

Page 9 / 11

Sep. 2003

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

Recommended PCB mechanical Drawing (Unit: mm)

Assembly Drawing (Unit: mm)

Recommend to use without or half clip

PCB BOARD BASE PLATE

S E N S O R C H IP PCB L E D C L IP

BASE PLATE 7.15 mm 7.15 mm 2.1 mm 2.1 mm

LENS

The maximum performance of optical mouse set can be achieved from applying the distances shown above. Lens to surface distance tolerance is ±0.2mm

Page 10 / 11

Sep. 2003

@Lab Optical Mouse Sensor + MCU ( ATA1092XA ) Data Sheet

ATA1092XA PACKAGE (Unit: mm)
Package Outline Drawing

Marking Information

000000 ATA1092XA
Page 11 / 11 Sep. 2003