Text preview for : CSDTD 31 Supp.pdf part of Aiwa CSD-TD31 Service Manual Cd Stereo Fm Tape Recorder - Tape mech. TN-21ZVC-2000, Cd mech. DA11T3C - (4.417Kb) 2 Part File - pag. 30
Back to : portable_stereo.part1.rar | Home
CSD-TD31 HR(S,L) EZ(S)
HA(S)
SERVICE MANUAL
COMPACT DISC STEREO RADIO CASSETTE RECORDER BASIC TAPE MECHANISM : TN-21ZVC-2000 BASIC CD MECHANISM : DA11T3C
S/M Code No. 09-003-342-8N2
DA TA
SPECIFICATIONS HA MODEL
·
Design and specifications are subject to change without notice .
EZ MODEL
HR MODEL
·
Design and specifications are subject to change without notice .
·
Design and specifications are subject to change without notice .
2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel:Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
Precaution to replace Optical block (SF-P101NR)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure.
PICK-UP Assy P.C.B
Solder
3
ELECTRICAL MAIN PARTS LIST
REF. NO IC
PART NO.
KANRI NO.
DESCRIPTION
REF. NO C321 C322 C325 C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C416 C417 C418 C419 C420 C421 C422 C423 C424 C425 C426 C428 C429 C430 C431 C432 C433 C434 C435 C436 C437 C438 C439 C440 C441 C442 C445 C446 C447 C448 C450 C451 C455 C457 C458 C459 C460 C461 C462 C463 C465 C466 C467 C469 C470 C471 C472 C473 C474 C475 C476 C477 C478
87-A21-550-010 87-A21-185-040 87-A21-064-010 87-A21-520-040 87-A20-446-010 87-A20-459-010 87-A21-093-010 8A-CH4-661-010 87-A21-431-010 TRANSISTOR 89-327-143-080 87-026-447-080 89-111-624-080 87-026-213-080 89-503-025-010 89-320-011-080 87-026-230-080 87-026-463-080 89-327-125-080 89-112-965-080 87-026-291-080 87-A30-226-010 87-026-462-080 89-318-154-080 89-109-332-380 89-113-187-080 87-026-239-080 87-026-464-080 DIODE 87-070-345-080 87-A40-616-070 87-A40-128-080 87-017-072-080 87-027-607-080 87-A40-648-080 87-A40-234-080 87-017-978-080 87-027-702-080 87-020-465-080 87-A40-465-010 MAIN C.B C30 C251 C261 C262 C263 C264 C265 C266 C267 C268 C271 C272 C278 C279 C301 C306 C307 C308 C311 C312 87-010-260-080 87-010-401-080 87-010-402-080 87-010-402-080 87-010-178-080 87-010-178-080 87-010-263-080 87-010-263-080 87-010-112-080 87-010-112-080 87-010-237-080 87-010-237-080 87-010-405-080 87-010-385-080 87-016-495-000 87-010-404-080 87-010-401-080 87-010-221-080 87-010-263-080 87-010-385-080
IC,TA2149N C-IC,LC72121M IC,LA4227 C-IC,M61509FP C-IC,LA9241ML C-IC,LC78622ED IC,LA6541D C-IC,LC867132V-5P07 IC,BA4560N
KANRI NO. 87-010-197-080 CAP, 87-010-263-080 CAP, 87-010-405-080 CAP, 87-010-403-080 CAP, 87-010-197-080 CAP, 87-010-263-080 87-010-248-080 87-010-197-080 87-010-374-080 87-010-178-080 87-010-198-080 87-010-248-080 87-010-263-080 87-A11-177-080 87-010-401-080 87-016-369-080 87-010-405-080 87-010-545-080 87-012-157-080 87-010-213-080 87-A11-608-080 87-016-369-080 87-A11-177-080 87-010-184-080 87-010-194-080 87-A10-712-080 87-010-176-080 87-A11-608-080 87-010-197-080 87-010-186-080 87-012-156-080 87-010-545-080 87-010-374-080 87-010-401-080 87-010-184-080 87-010-197-080 87-010-374-080 87-010-404-080 87-016-669-080 87-010-178-080 87-010-145-080 87-010-197-080 87-010-312-080 87-012-368-080 87-012-368-080 87-012-368-080 87-010-315-080 87-012-140-080 87-012-156-080 87-010-247-080 87-010-312-080 87-010-312-080 87-010-263-080 87-015-819-080 87-010-197-080 87-010-248-080 87-018-134-010 87-010-404-080 87-012-368-080 87-010-263-080 87-012-154-080 87-010-544-080 87-015-785-080 87-015-785-080 87-015-785-080 87-015-785-080 87-010-197-080 87-010-236-080 87-010-197-080 87-010-263-080 CAP, CAP, CAP, CAP, CHIP
PART NO.
DESCRIPTION CHIP 0.01 DM ELECT 100-10V ELECT 10-50V ELECT 3.3-50V CHIP 0.01 DM ELECT 100-10V ELECT 220-10V CHIP 0.01 DM ELECT 47-10V CAP 1000P
TR,2SC2714 (0.1W) TR,2SC1740S R TR,2SA1162Y CHIP-TR,DTC114YK C-FET,2SK302GR TR,2SC2001 (15W) CHIP-TR,DTA114YK TR,2SA933S (0.3W) C-TR,2SC2712(GR) TR,2SA1296 (0.75W) TR,DTC124XS TR,2SB1655E TR,2SC1740 S(RS 0.3W) TR,2SC1815 (0.4W) TR,2SA933RS TR,2SA1318TU TR,DTC114TK (0.2W) TR,DTC114TS (0.3W)
CAP, CHIP 0.022 CAP, ELECT 220-10V CAP, ELECT 100-10V C-CAP,S 0.15-16 K B CAP, ELECT 1-50V C-CAP,S 0.033-25 B K CAP, ELECT 10-50V CAP, ELECT 0.22-50V C-CAP,S 330P-50 CH C-CAP,S 0.015-50 B C-CAP,S 0.33-25 K B C-CAP,S 0.033-25 B K C-CAP,S 0.15-16 K B CHIP CAPACITOR 3300P(K) C-CAP,S 0.47-25V(Z)F C-CAP,S 0.22-25V(Z)F C-CAP,S 680P-50 SL C-CAP,S 0.33-25 K B CAP, CHIP 0.01 DM CAP,CHIP 4700P C-CAP,S 220P-50 CH CAP, ELECT 0.22-50V CAP, ELECT 47-10V CAP, ELECT 1-50V CHIP CAPACITOR 3300P(K) CAP, CHIP 0.01 DM CAP, ELECT 47-10V CAP, ELECT 4.7-50V C-CAP,S 0.1-25 K B CHIP CAP 1000P C-CAP,S 1P-50 CH CAP, CHIP 0.01 DM C-CAP,S 15P-50 CH C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F C-CAP,S 27P-50 CH CAP 470P C-CAP,S 220P-50 CH CAP, ELECT 100-50V C-CAP,S 15P-50 CH C-CAP,S 15P-50 CH CAP, ELECT 100-10V CAPACITOR,0.01 CAP, CHIP 0.01 DM CAP, ELECT 220-10V CAP, TC U 0.01-16NY UP050 CAP, ELECT 4.7-50V C-CAP,S 0.1-50 F CAP, ELECT 100-10V C-CAP,S 150P-50 CH CAP, ELECT 0.1-50V CHIP CAPACITOR, 0.1FZ-25Z CHIP CAPACITOR, 0.1FZ-25Z CHIP CAPACITOR, 0.1FZ-25Z CHIP CAPACITOR, 0.1FZ-25Z CAP, CHIP 0.01 DM CAP,E 1000-10 SME CAP, CHIP 0.01 DM CAP, ELECT 100-10V
DIODE,IN4148 VARI-CAP,SVC384(S/T) C-VARI-CAP,HVU202A ZENER,HZS3B1 ZENER,HZ7B3L ZENER,MTZJ8.2A ZENER,MTZJ5.6A DIODE,1N4003 ZENER,HZ6C2L DIODE,1SS133 (110MA) DIODE,FR202
CAP, CAP, CAP, CAP, CHIP CHIP CAP, CAP, CAP, CAP,
ELECT 47-25V ELECT 1-50V ELECT 2.2-50V ELECT 2.2-50V CAP 1000P CAP 1000P ELECT 100-10V ELECT 100-10V ELECT 100-16V ELECT 100-16V
CAP, ELECT 1000-16V CAP, ELECT 1000-16V CAP, ELECT 10-50V CAP, ELECT 220-25V EL CAP 3300UF/25V CAP, CAP, CAP, CAP, CAP, ELECT ELECT ELECT ELECT ELECT 4.7-50V 1-50V 470-10V 100-10V 220-25V
4
REF. NO C479 C480 C481 C482 C483 C484 C489 C490 C491 C493 C494 C495 C499 C501 C502 C503 C504 C505 C506 C510 C831 CN202 CN205 CN301 CN401 CN403 CN802 CNA402 JW425 JW429 JW442 L401 L402 L404 R840 SFR430 X401 TAPE C.B C211 C212 C215 C216 C231 C232 C233 C234 C235 C236 C237 C239 C240 C247 C248 C309 C310 C316 C801 C805 C806 C807 C808 C809 C810 C811 C812 C816
KANRI DESCRIPTION NO. 87-010-197-080 CAP, CHIP 0.01 DM 87-010-221-080 CAP, ELECT 470-10V 87-010-405-080 CAP, ELECT 10-50V 87-010-405-080 CAP, ELECT 10-50V 87-012-156-080 C-CAP,S 220P-50 CH 87-012-156-080 87-012-368-080 87-012-368-080 87-010-197-080 87-010-197-010 87-010-197-080 87-010-184-010 87-018-120-010 87-012-368-080 87-010-322-080 87-010-322-080 87-010-322-080 87-010-322-080 87-010-322-080 87-016-669-080 87-010-198-080 8A-CH4-689-010 87-A60-109-010 87-099-416-010 87-A60-424-010 87-099-201-010 87-049-469-010 8A-CDB-622-010 87-003-098-010 87-003-098-010 87-003-098-010 87-003-102-080 87-003-098-010 87-003-152-080 87-029-124-010 87-024-437-080 8Z-CD5-633-010 C-CAP,S 220P-50 CH C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F CAP, CHIP 0.01 DM C-CAP,S 0.01-25K B GRM CAP, CHIP 0.01 DM C-CAP,S 3300-50KB CAP,TC U 120P-50KB UP050 C-CAP,S 0.1-50 F C-CAP,S 100P-50 CH C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S 100P-50 CH 100P-50 CH 100P-50 CH 100P-50 CH 0.1-25 K B
PART NO.
REF. NO C817 C819 C820 C821 C822 C823 C824 C829 C830 C833 C834 C835 C836 C843 C844 C845 C846 C851 C852 C853 C853 CN201 CN801 CNA302 L801 SW801 FRONT C.B
KANRI DESCRIPTION NO. 87-010-180-080 C-CER 1500P 87-010-426-080 C-CAP,S 0.012-25 B 87-010-426-080 C-CAP,S 0.012-25 B 87-010-401-080 CAP, ELECT 1-50V 87-010-401-080 CAP, ELECT 1-50V 87-010-178-080 87-010-178-080 87-010-178-080 87-010-178-080 87-018-195-080 87-010-248-080 87-010-322-080 87-010-322-080 87-010-197-080 87-018-124-080 87-010-178-080 87-010-263-080 87-010-186-080 87-010-178-080 87-018-211-080 87-A11-145-080 87-099-018-010 87-A60-110-010 8A-CDB-627-010 87-007-342-010 88-CT6-619-010 CHIP CHIP CHIP CHIP CAP, CAP CAP CAP CAP CER 1000P 1000P 1000P 1000P 1200P-16V
PART NO.
CAP, ELECT 220-10V C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH CAP, CHIP 0.01 DM CAP, CER 270P-50V CHIP CAP 1000P CAP, ELECT 100-10V CAP,CHIP 4700P CHIP CAP 1000P CAP, CER 0.01-50 CAP,TC U 0.01-50 Z F CONN,16P CONN,4P V S2M-4W CONN ASSY,6P MA-TUNER COIL,OSC 85K BIAS BACK SLIDE SW 6P2T SHORTIN
CAP, CHIP 0.022 CONN BASE 3P 2.5mm CONN,2P V S2M-2W CONN,3P EH H WHT CONN,16P V TOC-B CONN,8P 6216 CONN,4P V CONN ASSY,6P COIL,2.2UH K COIL,2.2UH K H CD-MOTOR LAL02 LAL02
COIL,2.2UH K LAL02 COIL, 10UH COIL,2.2UH K LAL02 COIL, 100UH RES,FUSE 2.2-1/4 SFR100K,RH063EC VIB, CER16.93MHZ FCR16.93M2
C601 C602 C603 C604 C605 C606 C607 C608 C610 C611 C612 C613 C614 C615 C616 C620 C625 C661 CN601 CN602 CNA603 CNA604 CNA606 L601 LCD601 LED602 LED603 LED604 LED608 S601 S604 S605 S606 S607 X601 X602
87-010-313-080 87-010-315-080 87-010-415-040 87-010-312-080 87-010-317-080 87-015-785-080 87-010-196-080 87-010-196-080 87-010-555-040 87-010-196-080 87-A10-189-040 87-010-495-040 87-010-196-080 87-010-493-040 87-010-494-040 87-010-555-040 87-010-197-080 87-010-498-040 87-099-033-010 87-099-201-010 8A-CHB-616-010 8A-CHB-617-010 8A-CHB-621-010 87-003-171-010 8A-CHB-625-010 88-CD6-630-010 88-CD6-630-010 88-CD6-630-010 88-CD6-630-010 8Z-CT6-636-010 8Z-CT6-636-010 8Z-CT6-636-010 8Z-CT6-636-010 8Z-CT6-636-010 87-030-273-010 87-030-376-080
CAP, CHIP 18P C-CAP,S 27P-50 CH CAP,E 10-50 5L C-CAP,S 15P-50 CH C-CAP,S 39P-50 CH CHIP CAPACITOR, 0.1FZ-25Z CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP,E 100-10 GAS CHIP CAPACITOR,0.1-25 CAP,E 220-10 CAP,E 2.2-50 GAS CHIP CAPACITOR,0.1-25 CAP,E 0.47-50 GAS CAP,E 1-50 GAS CAP,E 100-10 GAS CAP, CHIP 0.01 DM CAP,E 10-16 GAS 16P 6216 H CONN,8P 6216 H CONN ASSY,4P TU-FR(DIGITAL) CONN ASSY,2P VOL-KEY CONN ASSY,8P FUNCT-KEY COIL,15UH TROIDAL LCD,HLC7107ACH-11 LED,934ID RED LED,934ID RED LED,934ID RED LED,934ID RED SW,TACT EVQJAC04M SW,TACT EVQJAC04M SW,TACT EVQJAC04M SW,TACT EVQJAC04M SW,TACT EVQJAC04M VIB,XTAL 32.768K5PPM VIB,CER CSA5.76MG200
87-010-805-080 87-010-805-080 87-016-460-080 87-016-460-080 87-010-213-080 87-010-213-080 87-A10-201-080 87-A10-201-080 87-016-669-080 87-016-669-080 87-010-408-080 87-010-197-080 87-010-197-080 87-010-401-080 87-010-401-080 87-010-197-080 87-010-248-080 87-010-384-080 87-010-248-080 87-012-365-080 87-012-365-080 87-010-405-080 87-010-405-080 87-010-405-080 87-010-405-080 87-010-178-080 87-010-178-080 87-010-180-080
CAP, S 1-16 CAP, S 1-16 C-CAP,S 0.22-16 B C-CAP,S 0.22-16 B C-CAP,S 0.015-50 B C-CAP,S 0.015-50 B C-CAP,S0.33-16 KB C-CAP,S0.33-16 KB C-CAP,S 0.1-25 K B C-CAP,S 0.1-25 K B CAP, CAP, CAP, CAP, CAP, ELECT 47-50V CHIP 0.01 DM CHIP 0.01 DM ELECT 1-50V ELECT 1-50V
CAP, CHIP 0.01 DM CAP, ELECT 220-10V CAP, ELECT 100-25V CAP, ELECT 220-10V C-CAP,S 0.027-25VBK C-CAP,S 0.027-25VBK CAP, ELECT 10-50V CAP, ELECT 10-50V CAP, ELECT 10-50V CAP, ELECT 10-50V CHIP CAP 1000P CHIP CAP 1000P C-CER 1500P
5
REF. NO TU C.B C1 C1 C2 C3 C3 C5 C6 C7 C8 C10 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C25 C26 C27 C28 C29 C30 C30 C31 C31 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 C47 C48 C49 C50 C51 C52 C53 C54 C55 C61 C64 C71 C72 C73 C91 C92 C93 CF1 CF2 CF2 CF3
PART NO.
KANRI NO.
DESCRIPTION
REF. NO CF3 CN2 CN3 HLD1 HLD2 L2 L3 L3 L4 L4 L5 L6 L7 L8 L51 TC1 TC51 X1 HP C.B CN203 J251 LED C.B CN607 LED605 LED606 LED611 S608 S609 S610 S611 S613 VOL C.B
87-010-312-080 87-010-314-080 87-010-316-080 87-010-312-080 87-010-314-080 87-A11-067-080 87-010-313-080 87-014-049-080 87-012-349-080 87-010-197-080 87-010-197-080 87-010-197-080 87-010-197-080 87-010-150-080 87-010-303-080 87-012-349-080 87-010-374-080 87-010-198-080 87-015-835-080 87-010-263-080 87-010-404-080 87-010-197-080 87-010-197-080 87-010-197-080 87-016-460-080 87-018-131-080 87-A11-067-080 87-016-669-080 87-016-669-080 87-010-213-080 87-010-198-080 87-010-213-080 87-010-198-080 87-A11-729-080 87-A11-729-080 87-015-819-080 87-010-263-080 87-010-197-080 87-010-374-080 87-010-404-080 87-010-197-080 87-012-349-080 87-012-349-080 87-012-349-080 87-010-311-080 87-010-312-080 87-010-197-080 87-010-197-080 87-010-197-080 87-012-140-080 87-010-197-080 87-010-316-080 87-010-197-080 87-010-197-080 87-014-055-080 87-010-197-080 87-010-184-080 87-010-314-080 87-010-197-080 87-010-263-080 87-010-197-080 87-010-197-080 87-010-197-080 87-010-197-080 87-A91-094-010 82-785-747-080 87-008-261-010 82-785-747-080
C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S
15P-50V 22P-50V 33P-50 CH 15P-50V 22P-50V
KANRI DESCRIPTION NO. 87-008-261-010 FILTER, SFE10.7MA5-A 87-099-194-010 CONN,6P 6216V 87-A60-110-010 CONN BASE 4P 88-CD6-661-010 HLDR,BAR ANT. 88-CD6-661-010 HLDR,BAR ANT. 87-A50-560-010 8A-CH4-670-010 8A-CH4-671-010 87-A50-420-010 87-A50-572-010 87-A50-566-010 87-A50-568-010 87-A91-308-010 87-005-849-080 87-A50-421-010 87-011-254-080 87-011-233-080 87-A70-061-010 COIL,FM BPF(ACD) BAR-ANT,MW 2B-ACH(COI) BAR-ANT,MW/LW 3B-ACH(COI) COIL,MW OSC(SYN) COIL,MW OSC-HE(ACH) COIL,FM RF EX(ACH) COIL,FM OSC EX(ACH) FLTR,PCFAZH- 450T (TOK) COIL,10UH(CECS) COIL,LW OSC(SYN) TRIMER,20P LAR TRIMER,50P VCT54 VIB,XTAL 4.500MHZ CSA-309
PART NO.
C-CAP,S 1-10 K B CAP, CHIP 18P CAP,PP 470P-100 J C-CAP,S 1000P-50 CH CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM C-CAP,S 6P-50 CH C-CAP,S 330P-50CH C-CAP,S 1000P-50 CH CAP, ELECT 47-10V CAP, CHIP 0.022 C-CAP,0.047 D CAP, ELECT 100-10V CAP, ELECT 4.7-50V CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM C-CAP,S 0.22-16 B CAP, CER 1000P-50V C-CAP,S 1-10 K B C-CAP,S 0.1-25 K B C-CAP,S 0.1-25 K B C-CAP,S 0.015-50 B CAP, CHIP 0.022 C-CAP,S 0.015-50 B CAP, CHIP 0.022 C-CAP,0.47-16V Y5V C-CAP,0.47-16V Y5V CAPACITOR,0.01 CAP, ELECT 100-10V CAP, CHIP 0.01 DM CAP, ELECT 47-10V CAP, ELECT 4.7-50V CAP, CHIP 0.01 DM C-CAP,S 1000P-50 CH C-CAP,S 1000P-50 CH C-CAP,S 1000P-50 CH CAP 12P C-CAP,S 15P-50 CAP, CHIP 0.01 CAP, CHIP 0.01 CAP, CHIP 0.01 CAP 470P CH DM DM DM
87-049-469-010 87-009-216-010
CONN,4P V JACK, DIA 3.5
87-009-236-010 88-CD6-630-010 88-CD6-630-010 88-CD6-631-010 8Z-CT6-636-010 8Z-CT6-636-010 8Z-CT6-636-010 8Z-CT6-636-010 8Z-CT6-636-010
CONN 8P PH H LED,934ID RED LED,934ID RED LED,934GD GRN SW,TACT EVQJAC04M SW,TACT SW,TACT SW,TACT SW,TACT EVQJAC04M EVQJAC04M EVQJAC04M EVQJAC04M
CN608 S614 S615 PWR C.B C901 C902 C903 C904 CNA901 !PR901 MOTOR C.B
84-722-632-010 8Z-CT6-636-010 8Z-CT6-636-010
CONN,2P H SW,TACT EVQJAC04M SW,TACT EVQJAC04M
87-018-205-080 87-018-205-080 87-018-205-080 87-018-205-080 8A-CDB-621-010 87-A90-092-080
CAP, CAP, CAP, CAP, CONN
CERA-SOL 0.022 CERA-SOL 0.022 CERA-SOL 0.022 CERA-SOL 0.022 ASSY,3P POWER
PROTECTOR,2.5A 491
CAP, CHIP 0.01 DM C-CAP,S 33P-50 CH CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP,PP 820P-100 J CAP, CHIP 0.01 DM CHIP CAPACITOR 3300P(K) C-CAP,S 22P-50V CAP, CHIP 0.01 DM CAP, ELECT 100-10V CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM FLTR,CDA10.7 MG80A CF,MS2 GHY,R FILTER, SFE10.7MA5-A CF,MS2 GHY,R
M2 PIN3 SW1 BATT C.B
9X-262-576-910 91-564-722-110 91-572-085-120
MOTOR GEAR ASSY CONNECTOR 6P LEAF SW
6
LCD DISPLAY LCD, HLC7107ACH-11
· Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Resistor Code Value of resistor Chip resistor
Dimensions (mm)
Figure
Wattage 1/16W 1/16W 1/10W 1/8W
Type 1005 1608 2125 3216
Tolerance 5% 5% 5% 5%
Symbol CJ CJ CJ CJ
Form
L W
L 1.0
t
W 0.5 0.8 1.25 1.6
t 0.35 0.45 0.45 0.55
:A Resistor Code : A
104 108 118 128
1.6 2 3.2
TRANSISTOR ILLUSTRATION
S B G E
C
D ECB ECB
ECB
ECB
2SB1655E
DTC114TS
2SK302GR
2SA1162Y 2SC2712 2SC2714 DTA114YK DTC114TK DTC114YK
2SA933RS 2SC1740S R DTC124XS
2SA933S 2SA1296 2SA1318TU 2SC1740 S 2SC1815 2SC2001
7
8
WIRING-1 (MAIN/TAPE)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
HA
JW442
HR,EZ
MOTOR C.B
M2
HR,EZ
B
HR,EZ
+ _
HA
M2 (SLED MOTOR) SW1 (INSIDE LIMIT SW) M3 (SPINDLE MOTOR)
C493
HA
HR,EZ
C 49 9
HR,EZ
C
HA JW425
PIN3
HR,EZ
SW1
_
D
+
M3
HR,EZ JW429 HA
E
F
G
H
I
J
K 9 10
SCHEMATIC DIAGRAM-1 (MAIN)
HA, HR MODEL
C812 1000P R810 330K
C811 1000P R809 330K
EZ MODEL
AC230V50Hz
HZ7B3L 4.7k
1N4148
11
12
SCHEMATIC DIAGRAM-2 (CD)
X401 VIB,CER 16.934MHz (TDK)
15p
100
15p
25
R499 33k
JW442 *29
0.01
C499 *26
JW429 27
*19 *25 *27 *28 *20 *24 *26 *29 *21 (OPTI OUT) (C494) (C493) (C495) (L402) (C499) (JW429) (JW425) (JW442) JW NM HA NO MOUNT 0.01 JW JW NM JW NM 0.01 0.01 2.2µ 120p COIL 2.2µ COIL 2.2µ COIL 2.2µ HR NM EZ NM
13
JW425 *28
C495 *24
14
WIRING-2 (POWER)
1 2 3 4 5 6 7
A
HA, HR MODELS
B
EZ MODEL
C AC 230V 50Hz
D
E
F
G
H
I
J
K 15
WIRING-3 (TU: HA, HR)
1 2 3 4 5 6 7
A
B
C
D
E
F
G
H
I
J
K 16
SCHEMATIC DIAGRAM-3 (TUNER: HA, HR)
1µ
VT
TU C.B
17
18
SCHEMATIC DIAGRAM-4 (TUNER: EZ)
19
20
WIRING-4 (TUNER: EZ)
1 2 3 4 5 6 7
IC BLOCK DIAGRAM IC, M61509FP
INA1 1 Mono.SW INB1 INC1 IND1 INE1 2 3 4 5 VOL VOL MUTE 23 22 21 20 INB2 INC2 IND2 INE2 24 INA2
IC, LA6541D
A
B
QF1 QF2 TONEH1 TONEL1 6 7 8 9 10 11 12
Treble boost
Treble boost 19 18 17 16 Bass boost Bass boost 15 14 Control logic 13 QF4 QF3 TONEH2 TONEL2 OUT2 VSS CONT
ATT
ATT
C
OUT1 GND VDD
D
IC, TA2149N
IC, LC72121M
E
F
G
H
IC, BA4560N
I
J
K 21 22
WIRING-5 (FRONT)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
HA,HR
HA
EZ
E
F
G
H
I
J
K 23 24
SCHEMATIC DIAGRAM-5 (FRONT)
HA,HR
HA,HR
25
100µ10v
26
ELECTRICAL ADJUSTMENT
L003 (BAR-ANT)
< TUNER SECTION > (HA, HR MODEL)
1. AM IF Adjustment L007 ....................................................................... 450kHz 2. AM VT Adjustment Settings: · Test point: C39+ · Adjustment location: L004 (HA MODEL) Method: Set to AM 1000kHz adjust L004 so that the test point becomes 3.24 V±0.02V (HR MODEL) Method: Set to MW 999kHz adjust L004 so that the test point becomes 3.24 V±0.02V 3. AM Tracking Adjustment L003 ....................................................................... 600kHz TC001, L007 ........................................................ 1400kHz
J251 L006 L051
< TAPE SECTION >
8. Bias frequency Adjustment L801 ............................................................... 85Hz ±1kHz 9. Tape speed Adjustment Settings: · Test tape: TTA-100 · Test point: PHONES JACK (J251) · Adjustment location: SFR of deck motor Method: Play back the test tape and adjust so that the output frequency is 3000Hz ±30Hz. 10. Azimuth Adjustment Settings: · Test tape: TTA-320 · Test point: PHONES JACK (J251) · Adjustment location: Azimuth adjustment screw Method: Play back the test tape and adjust so that the output is maximum.
TU C.B
3
5
L007 IC001
L005
TC051
TC001
3 HP C.B 7
EZ MODEL
L004
13
2
EZ MODEL
90
4. FM VT Adjustment Settings: · Test point: C39+ · Adjustment location: L006 Method: Set to FM 108MHz adjust L006 so that the test point becomes 6.0V±0.2V 5. FM Tracking Adjustment L005 ........................................................................ 98MHz
4 6
(EZ MODEL)
1. MW IF Adjustment L007 ....................................................................... 450kHz
C39 +
2. MW VT Adjustment Settings: · Test point: C39+ · Adjustment location: L004 Method: Set to MW 999kHz adjust L004 so that the test point becomes 3.8V±0.02V 3. MW Tracking Adjustment L003 ....................................................................... 603kHz TC001, L007 ........................................................ 1404kHz 4. FM VT Adjustment Settings: · Test point: C39+ · Adjustment location: L006 Method: Set to FM 108MHz adjust L006 so that the test point becomes 6.0V±0.2V 5. FM Tracking Adjustment L005 ........................................................................ 98MHz
L801
246 TAPE C.B
6. LW VT Adjustment Settings: · Test point: C39+ · Adjustment location: L051 Method: Set to LW 288kHz adjust L051 so that the test point becomes 4.60V±0.02V 7. LW Tracking Adjustment L003 ....................................................................... 153kHz TC051 ..................................................................... 288kHz
8
M1 (DECK MOTOR)
0
9
27 28
IC DESCRIPTION IC, LA9241ML
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Pin Name FIN2 FIN1 E F TB TE TE TESI SCI TH TA TD TD JP TO FD FD I/O I I I I I I O I I I O I I I O O I Description Pin to which external pickup photo diode is connected. RF signal is created by adding with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal. Pin to which external pickup photo diode is connected. Pin to which external pickup photo diode is connected. TE signal is created by subtracting from the F pin signal. Pin to which external pickup photo diode is connected. DC component of the TE signal is input. Pin to which external resistor setting the TE signal gain is connected between the TE pin. TE signal output pin. TES "Track Error Sense" comparator input pin. TE signal is passed through a bandpass filter then input. Shock detection signal input pin. Tracking gain time constant setting pin. TA amplifier output pin. Pin to which external tracking phase compensation constants are connected between the TD and VR pins. Tracking phase compensation setting pin. Tracking jump signal (kick pulse) amplitude setting pin. Tracking control signal output pin. Focusing control signal output pin. Pin to which external focusing phase compensation constants are connected between the FD and FA pins. 18 FA I Pin to which external focusing phase compensation constants are connected between the FD and FA pins. 19 20 21 22 23 24 25 26 27 28 29 30, 31 32, 33 34 35 FA FE FE AGND SP SPI SPG SP SPD SLEQ SLD SL, SL+ JP, JP+ TGL TOFF I O I -- -- O I I O I O I I I I Pin to which external focusing phase compensation constants are connected between the FA and FE pins. FE signal output pin. Pin to which external FE signal gain setting resistor is connected between the FE pin. Analog signal GND. No connection. Single ended output of the CV+ and CV pin input signal. Pin to which external spindle gain setting resistor in 12 cm mode is connected. Pin to which external spindle phase compensation constants are connected together with SPD pin. Spindle control signal output pin. Pin to which external sled phase compensation constants are connected. Sled control signal output pin. Sled advance signal input pin from microprocessor. Tracking jump signal input pin from DSP. Tracking gain control signal input from DSP. Low gain when TGL = H. Tracking off control signal input pin from DSP. Off when TOFF = H.
29
Pin No. 36 37 38 39, 40 41 42
Pin Name TES HFL SLOF CV, CV+ RFSM RFS
I/O O O I I O I
Description Pin from which TES signal is output to DSP. "High Frequency Level" is used to judge whether the main beam position is on top of bit or on top of mirror. Sled servo off control input pin. CLV error signal input pin from DSP. RF output pin. RF gain setting and EFM signal 3T compensation constant setting pin together with RFSM pin.
43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
SLC SLI DGND FSC TBC NC DEF CLK CL DAT CE DRF FSS VCC2 REFI VR LF2 PH1 BH1 LDD LDS VCC1
O I -- O I -- O I I I I O I -- -- O I I I O I --
"Slice Level Control" is the output pin which controls the RF signal data slice level by DSP. Input pin which control the data slice level by the DSP. Digital system GND. Output pin to which external focus search smoothing capacitor is connected. "Tracking Balance Control" EF balance variable range setting pin. No connection. Disc defect detector output pin. Reference clock input pin. 4.23 MHz of the DSP is input. Microprocessor command clock input pin. Microprocessor command data input pin. Microprocessor command chip enable input pin. "Detect RF" RF level detector output. "Focus Search Select" focus search mode (± search/+ search) select pin. Servo system and digital system Vcc pin. Pin to which external bypass capacitor for reference voltage is connected. Reference voltage output pin. Disc defect detector time constant setting pin. Pin to which external capacitor for RF signal peak holding is connected. Pin to which external capacitor for RF signal bottom holding is connected. APC circuit output pin. APC circuit input pin. RF system Vcc pin.
30
IC, LC78622ED
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12, 13 14 15 16 17 18 19, 20 21 22 23 24 25 26 27 28 29 30 31 32, 33 34 35 36 37 38 39 40 41 42 Pin Name DEFI TAI PDO VVSS ISET VVDD FR VSS EFMO EFMIN T2 CLV+, CLK___
I/O I I O -- I -- I -- O For slice level control. I I O O I I O O O O O -- O O -- I O O O O I -- O -- O -- -- O -- O R-channel 1-bit DAC. L-channel 1-bit DAC. For PLL.
Description Defect sense signal (DEF) input pin. (Connect to 0V when not used). Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Phase comparator output pin to control external VCO. GND pin for built-in VCO. Be sure to connect to 0V. Pin to which external resistor adjusting the PD0 output current. Power supply pin for built-in VCO. Pin for VCO frequency range adjustment. Digital system GND. Be sure to connect to 0V. EFM signal output pin. EFM signal input pin. Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Disc motor control output. Three level output is possible using command. Rough servo or phase control automatic selection monitoring output pin. Rough servo at H. Phase servo at L.
V/P HFL TES TOFF TGL JP+, JPPCK FSEQ VDD SL+ SL-- PUIN RW EMPH C2F DOUT T3, T4 N.C. MUTEL LVDD LCHO LVSS RVSS RCHO RVDD MUTER
Track detect signal input pin. Schmidt input. Tracking error signal input pin. Schmidt input. Tracking OFF output pin. Tracking gain selection output pin. Gain boost at L. Track jump control signal output pin. Three level output is possible using command. EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in. Sync signal detection output pin. H when the sync signal which is detected from EFM signal and thesync signal which is internally generated agree. Digital system power supply pin. Moves the sled to outer circumference. Moves the sled to inner circumference. Not connected. CD pickup inner switch detection. Read, wright signal. De-emphasis monitor output pin. De-emphasis disc is being played back at H. C2 flag output pin. DIGITAL OUT output pin. (EIAJ format). Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Not used. Set the pin to open. L-channel mute output pin. L-channel power supply pin. L-channel output pin. L-channel GND. Be sure to connect to 0V. R-channel GND. Be sure to connect to 0V. R-channel output pin. R-channel power supply pin. R-channel mute output pin.
31
Pin No. 43 44 45 46 47 48 49 50 51
Pin Name XVDD XOUT XIN XVSS SBSY EFLG PW SFSY SBCK
I/O -- O I -- O O O O I Crystal oscillator power supply pin.
Description
Pin to which external 16.9344 MHz crystal oscillator is connected. Crystal oscillator GND pin. Be sure to connect to 0V. Subcode block sync signal output pin. C1, C2, single and dual correction monitoring pin. Subcode P, Q, R, S, T, U and W output pin. Subcode frame sync signal output pin. Falls down when subcode enters standby. Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not in use.)
52 53 54 55 56 57 58 59 60 61 62 63 64
FSX WRQ RWC SQOUT COIN
___________
O O I O I I I O O O I I I
Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of crystal oscillator. Subcode Q output standby output pin. Read/write control input pin. Schmidt input. Subcode Q output pin. Command input pin from microprocessor. Command input read clock or subcode read input clock from SQOUT pin LC78622 reset input pin. Set this pin to L once when the main power is turned on. Test signal output pin. Use this pin as open (normally L output). 16.9344 MHz output pin. 4.2336 MHz output pin. Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V while it is not controlling.
CQCK RES T11 16M 4.2M T5
______
CS T1
Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.
32
IC, LC867132V-5P07
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37-40 41 42 43-50 51-54 Pin Name O-RMC/CE O-DATA O-CLK NC O-CLK SFT I-HOLD I-RST XT1 (IN) XT2 (OUT) VSS1 CF1 (IN) CF2 (OUT) VDD1 I-FM ST I-KEYO I-CD SW I-KEY1 I-MOTOR I-REC I-FM/AM (NC) I-TU DO O-BASS LED (NC) O-QS LED NC O-INT I-DRF I-WRQ I-REMO SO/PAO (NC) S1/PA1 (NC) S2/PA2 S3/PA3 (NC) S4/PA4 (NC) S5/PA5 (NC) S6/PA6 S7/PA7 S8-S11 VDD3 VSS3 S12-S19 S20-S23 (NC) I/O O O O -- O I I I O -- I O -- I I I I I I I I O O -- O I I I O O O O O O O O O -- -- O O Power supply for microcomputer (+5V). GND. LCD segment output. LCD segment output. (Not Connected) Power supply for microcomputer (+5V). FM STEREO status input. KEY AD input. CD DOOR SW status detection input. KEY AD input. DECK MECHA MOTOR status input. REC status input. FM, AM status input. (Not connected) Data input from tuner PLL. BASS LED ON/OFF control output. (Not connected) Q-Sound LED ON/OFF control output. Not connected. INT DIODE MATRIX detection output. CD RF level detection input. CD sub-code Q standby input. Remote control input. LCD segment output and initial settings output. (SW) (Not connected) LCD segment output and initial settings output. (LW) (Not connected) LCD segment output and initial settings output. (MW 10K) LCD segment output and initial settings output. (FM WIDE) (Not connected) LCD segment output and initial settings output. (OIRT) (Not connected) LCD segment output and initial settings output. (SW2) (Not connected) LCD segment output and initial settings output. (SYN) LCD segment output and initial settings output. GND. Connected to 5.76MHz Ceramic Filter. CD read/write control output. Data output to sound processor IC (M62495FP). Clock output to sound processor IC (M62495FP). Not Connected. Clock shift output of the microcomputer. Hold status detection. Microcomputer reset. Connected to 32.768kHz crystal oscillator. Description Pin No. 55 56 57 58 59 60 61 62 63 64-66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Pin Name O-CD LED O-TU LED O-TA LED (NC) O-ROCK LED O-POP LED O-JAZZ LED NC I-CD TEST (NC) I-TU TEST (NC) COM0-COM2 NC VSS2 VDD2 O-CD ON O-TU ON O-P.CONT NC O-MUTE O-FM MONO (NC) O-BEAT CONT O-QSOUND O-COIN I-SQOUT O-CQCK I/O O O O O O O -- I I O -- -- -- O O O -- O O O O O I O LCD common output. Not connected. GND. Power supply for microcomputer (+5V). CD PWR control output. TU PWR control output. Power supply control output. Not connected Main mute output. FM force control MONO output. (Not connected) BEAT switch over output. Q-Sound ON/OFF output. CD command output. CD sub-code Q input. CLK for CD commands/sub-codes. Not connected. Description LED ON/OFF control output for CD functions. LED ON/OFF control output for TU functions. LED ON/OFF control output for TAPE functions. (Not Connected) LED ON/OFF control output for ROCK. LED ON/OFF control output for POP. LED ON/OFF control output for JAZZ.
33
34
MECHANICAL EXPLODED VIEW 1/1
P.C.B H 28 19 23 C H 42 18 52 22 21 D 24 17 16 15 14 C 13 H C 6 C H 5 10 57 10 10 9 8 58 H 6 C C 2 4 6 12 5 C 3 56 H D G D 36 D TN-21ZVC-2000 53 47 9 46 37 LCD P.C.B 38 35 51 30 P.C.B P.C.B 48 6 26 A P.C.B 26 25 A A 26 A D 54 P.C.B P.C.B H D 39 F F 45 49 20 25 27 31 7 34 33 P.C.B D 55 50 44 24 32 CHASS,TU BAR-ANT 40 E B D E H H D B 43 29 H H 41
11
7
D
1
35
36
MECHANICAL PARTS LIST 1/1
REF. NO 1 1 2 2 3 4 5 6 8 9 10 11 11 11 12 12 13 14 15 16 17 18 18 19 19 20 20 21 22 23 24 25 26 27 28 29 30 31 32 33
KANRI DESCRIPTION NO. 8A-CDB-006-010 WINDOW,CASS 8A-CDB-061-010 WINDOW,CASS BL 8A-CDB-008-010 BOX,CASS 8A-CHB-037-010 BOX,CASS BL 8A-CDB-204-010 SPR-T,CASS 8A-CDB-001-010 88-CD8-622-010 8Z-CDB-208-010 87-063-164-010 8A-CDB-206-010 8A-CDB-016-010 8A-CHB-047-010 8A-CHB-013-010 8A-CHB-016-010 8A-CDB-023-010 8A-CDB-067-010 8Z-CT6-213-010 8Z-CT6-214-010 87-036-368-010 86-CT9-222-010 86-CT9-217-010 8A-CDB-009-010 8A-CDB-088-010 8A-CHB-011-010 8A-CDB-068-010 8A-CHB-014-010 8A-CHB-041-010 8A-CDB-213-010 8A-CDB-014-010 8A-CDB-003-010 8A-CDB-021-010 8A-CDB-203-010 88-CH6-220-010 8Z-CT9-064-010 87-036-389-010 8A-CDB-218-010 8A-CDB-620-010 M8-ZZK-E90-070 87-063-165-010 8A-CDB-214-010 CABI,FR SPKR,F 77 7OHM 3W HLDR,SPKR OIL-DMPR 80 BASE,CD BTN,CD WINDOW,DISP EX BL WINDOW,DISPLAY WINDOW,DISPLY GRILLE,SPKR GRILLE,SPKR BL BASE,CHUCK RING,CHUCK MAGNET PLATE,MAGNET HLDR,CHUCK A(S) BOX,CD BOX,CD EX BL WINDOW,CD WINDOW,CD BL BTN,FUNC BTN,FUNC EX BL BASE,FUNC BTN,QSOUND CHAS,CD LENS,FUNC HLDR,LED FUNC CUSHION,CD A PANEL CD SW,PUSH LOCK SPR-T,CD CONN ASSY,2P CD-DOOR DA11T3C OIL-DMPR 150 BASE,VOL
PART NO.
REF. NO 34 34 35 36 37 38 39 40 40 41 42 43 44 45
KANRI DESCRIPTION NO. 8A-CDB-012-010 BTN,VOL 8A-CDB-065-010 BTN,VOL BL 8A-CHB-202-010 HLDR,LCD 8A-CDB-212-010 PLATE,REC 8A-CHB-619-010 FF-CABLE, 8P 1.25 CD-FR 8A-CHB-618-010 8A-CDB-219-010 8A-CDB-653-010 8A-CDB-651-010 8A-CDB-019-010 8A-CDB-018-010 8Z-CH4-640-010 8A-CHB-001-010 87-A91-369-010 FF-CABLE, 16P 1.25 FR-MAIN HLDR,TRAN PT,E 2.5W EI48X23 PT,H 2.5W EI48X23 HANDL,GRIP COVER, HANDL ANT,ROD CABI,REAR SW,AC SL 2 2 2 SDKGA41700 FF-CABLE, 16P 1.0 CD-RF LID,BATT CUSH,FOOT HLDR,ANT JACK,AC E W/SW SPR-T,BATT HLDR,M66 BAR ANT KEY,CASS PLATE,TRAN COVER,AC-SOCKET CONN ASSY,4P CASS HEAD CONN ASSY,4P SPKR CONN ASSY,4P CASS MECHA SCREW CD VT1+3-30 UT2+3-10 SCREW 3X12 SCREW,V+3-10 GLD UT2+2.6-8 SCREW,V+2-3 GLD VT2+3-8 W/O
PART NO.
! !
!
46 8A-CDB-623-010 47 48 49 50 51 52 53 54 55 56 57 58 A B C D E F G H 8A-CDB-020-010 86-CT9-223-010 8A-CDB-207-010 87-A60-178-010 8A-CDB-215-010 8A-CDB-220-010 8A-CDB-015-010 8A-CDB-216-010 87-A90-086-010 8A-CDB-626-010 8A-CDB-633-010 8A-CDB-625-010 81-CD5-204-010 87-651-104-410 87-741-096-410 87-751-097-410 87-261-096-410 87-741-074-410 87-261-032-410 87-751-095-410
!
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color B Black C Cream D Orange G Green H Gray L Blue LT Transparent Blue N Gold P Pink R Red S Silver ST Titan Silver T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange
37
TAPE MECHANISM EXPLODED VIEW 1/1
F G 52 46 1 E 2 3 47 4 5 LUG PLATE
25
8 a 9 10 J L 12 11
21 20 22 18 23 24 36 c 51 26 27 28 A 6 29 7 C 48 37 38 39 D D K 42 41 I 50 43 H B B 40 C a 34 35 c b 33 A 19 b 14 15 16 17 49 30 13 31 32
44
45
38
TAPE MECHANISM PARTS LIST 1/1
REF. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
KANRI DESCRIPTION NO. S1-921-030-4A0 HEAD BASE S1-821-030-070 AZIMUTH SPRING S1-921-030-090 PANEL P SPRING S1-921-260-050 GEAR PLATE SPRING S1-921-265-020 GEAR PLATE ASSY S1-510-020-020 S1-921-015-010 S1-921-030-110 S1-921-143-160 S1-921-141-8A0 S1-921-260-4A0 S1-921-043-100 S1-921-130-010 S1-921-141-3A0 S1-921-140-550 S1-921-140-120 S1-921-140-110 S1-921-140-150 S1-821-011-590 S1-921-141-070 S6-401-011-490 S1-921-140-090 S1-921-140-080 S1-921-140-190 S1-921-030-100 S1-921-140-040 S1-921-140-050 S1-921-140-060 S1-921-140-600 S1-821-100-700 S1-921-050-060 S1-921-053-100 S1-829-100-010 S1-921-050-150 S1-921-050-220 REC SPRING PLATE CHASSIS ASSY HEAD PANEL BASE ASSY M CONTROL SPRING SENSING LEVER PINCH ROLLER ARM ASSY EJECT SLIDE LEVER P CONTROL SPRING PAUSE LEVER(E) PAUSE LEVER SPRING PAUSE STOPPER BUTTON LEVER SPRING(B) E KICK LEVER BUTTON LEVER SPRING(A) LEAF SW MSW-1541T SWITCH ACTUATOR PUSH BUTTON ACTUATOR PLAY BUTTON LEVER MG ARM SPRING REW BUTTON LEVER FF,BUTTON REVER STOP BUTTON LEVER PAUSE BUTTON LEVER FF GEAR SENSER TAKE UP REEL ASSY PACK SPRING S REEL HUB BACK TENSION SPRING
PART NO.
REF. NO 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 A B C D E F G H I J K L
KANRI DESCRIPTION NO. S1-921-140-030 REC BUTTON LEVER S1-921-140-170 P.S.LEVER SPRING S1-921-073-040 RF CLUTCH ASSY S1-921-070-030 RF BELT S1-921-260-020 CAM GEAR S1-921-140-160 S1-921-093-210 S1-921-090-380 S1-921-120-590 S6-002-030-220 S6-209-100-100 S1-921-030-050 S1-921-140-210 S1-821-100-690 S1-821-128-9A0 S1-821-010-500 S6-201-011-110 S9-P04-200-310 S1-921-120-020 S9-B10-200-510 S9-C07-204-510 S9-P01-200-610 S9-B01-200-310 S9-F08-200-710 S1-921-120-030 S9-W02-300-100 S9-W02-500-100 S9-W01-400-100 S9-W01-130-200 E ACTUATOR SPRING FLYWHEEL ASSY MAIN BELT MOTOR PULLEY MOTOR EG530AD-2B E HEAD PH-K380-MS1 MG ARM REC BUTTON LEVER SPRING RECORD SAFETY LEVER MOTOR BRACKET PLAY BUTTON LEVER SPRING HEAD,RP7442ES-0951 C TAPPING SCREW 2-3 MOTOR COLLER SCREW P TAPPING BIND SCREW M2-5 SCREW,TAPPING(CAMERA)M2-4.5 SCREW,M2-6 (+)BIND SCREW M2-3 AZIMUTH SCREW M2-7 MB SCREW P P P P WASHER WASHER WASHER WASHER CUT 1.2-3.8-0.3 CUT 1.45-3.8-0.5 2-3.5-0.4 2.1-4-0.13
PART NO.
39
CD MECHANISM EXPLODED VIEW 1/1
B SHAFT,SLIDE
SF-P101NR
B 1
2 A
A CHASSIS 3
SPINDLE MOTOR(M3)
MOTOR C,B
CD MECHANISM PARTS LIST 1/1
REF. NO 1 2 3 A B
KANRI DESCRIPTION NO. S2-121-A28-400 COVER GEAR S2-511-A21-000 GEAR MIDDLE S2-511-A21-100 GEAR,DRIVE S1-PN2-03R-OSE SCR PAN PCS 2-3 87-261-073-410 SCR S-TPG FLT 2.6-6 DA11T3C
PART NO.
ALL M8-ZZK-E90-070
40
ACCESSORIES/PACKAGE LIST
REF. NO 1 1 1 2 3
! !
KANRI DESCRIPTION NO. 8A-CHB-906-010 IB,EZ(9L)FM 8A-CHB-901-010 IB,H(ECA)FM 8A-CHB-902-010 IB,LH(ESP)FM 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL 87-A91-017-010 PLUG,CONVERSION JT-0476
PART NO.
41
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111
737004 Printed in Singapore