Text preview for : CBCFECFI.PDF part of Carl Zeiss Planar, Tessar, Sonnar, Distagon Service Manual Hasselblad Optik Carl Zeiss - (6.702Kb) 3 Part File - pag. 156



Back to : CB_CFE_CFI.part1.rar | Home

Carl Zeiss
CB/CFE/CFi Service Manual 00: 01: 02: 03: 04: 05: 06: 07: 08: 09: 10: 11: 12: 13: 14: 15: General Information Planar Tessar Distagon Makro-Planar Planar Distagon Tele-Superachromat F-Distagon Distagon Planar Makro-Planar Sonnar Sonnar Sonnar Sonnar-Superachromat

Contents List

2,8/80 4,8/160 3,5/60 4/120 2,8/80 4/40 5,6/350 3,5/30 4/50 3,5/100 4/120 4/150 4/180 5,6/250 5,6/250

CB CB CB CB CFE CFE CFE CFi CFi CFi CFi CFi CFi CFi CFi

Revision 0

March 1999

Carl Zeiss
CB - CFE - CFi Lenses 29/97 33/97 07/98 06/99 15/99 01/00 09/00 10/00 03/01 04/01

Related Service Infos

New lenses - CB 2.8/80, CB 3.5/60, CB 4.8/160 Preliminary spare part catalogue - CB 2.8/80 New tools - CB 2.8/80 and CB 4.8/160 New spare part catalogue - CB, CFE and CFi lenses Service Manual completed - CB, CFE and CFi lenses New CD-ROM - Version 1.2 New CD-ROM - Version 1.3 Service Policy - C lenses Modified shutter parts New CD-ROM - Version 2.0

Revision 3

January 2001

Carl Zeiss
CB/CFE/CFi Service Manual

Prefactory Note 00:0:01

This Service Manual comprises a spare parts catalogue, a tools catalogue, a repair instruction and a lubrication plan. Determinant for the availability of spare parts is the latest state effective of the spares price list, as may from time to time be established. The basic lens for lists and descriptions is the Planar 2,8/80 CB. The lists and descriptions of the remaining lenses are showing only the differences to the Planar 2,8/80 CB. That means: What you don't find in the chapter of one lens you will find in the Planar 2,8/80 CB chapter. All repair descriptions deal with disassembly only. Assembling is therefore always carried out in the reverse order. Exceptions are mentioned by the text.

Page numbering system 01:1:01 page number subchapter: 1=spare part list 2=tools list 3=repair instruction 4=lubrication plan chapter (ordinal number of a lens in the manual)

Figure numbering system Fig. 01:1:01/1-1 reference number figure number page number

Ordering numbers The spare parts and tools have 13-digit ordering numbers like `102165-0011-180'. There are two exceptions: Some parts have a format like `VHAB Code No. 50377' which you will find in the remark column. Some parts have a format like `200 509', then you will find `VHAB Spare Part No.' in the remark column.

Revisions and dates To make sure, that your Service Manual is always up to date every page has a Revision counter and a date field. On the next pages you will find the Index of Current Pages, that gives you an overview over the complete Service Manual and informs you what to do in case of changes.

Revision 0

July 1999

Carl Zeiss
Page No. Rev. Date Cont. List 0 March 1999 00:0:01 0 July 1999 00:0:02 3 December 2000 00:0:03 2 December 2000 01:1:01 0 January 1999 01:1:02 0 January 1999 01:1:03 0 January 1999 01:1:04 0 January 1999 01:1:05 0 January 1999 01:1:06 0 January 1999 01:1:07 0 January 1999 01:1:08 0 January 1999 01:1:09 0 May 1999 01:1:10 0 January 1999 01:1:11 1 December 2000 01:1:12 1 December 2000 01:1:13 0 January 1999 01:1:14 0 January 1999 01:1:15 0 January 1999 01:1:16 0 January 1999 01:2:01 0 May 1999 01:3:01 0 July 1999 01:3:02 0 July 1999 01:3:03 0 July 1999 01:3:04 0 July 1999 01:3:05 0 July 1999 01:3:06 0 July 1999 01:3:07 0 July 1999 01:3:08 0 July 1999 01:3:09 0 July 1999 01:3:10 0 July 1999 01:3:11 0 July 1999 01:3:12 0 July 1999 01:3:13 0 July 1999 01:3:14 0 July 1999 01:3:15 0 July 1999 01:3:16 1 January 2000 01:3:17 0 July 1999 01:3:18 0 July 1999 01:3:19 0 July 1999 01:3:20 0 July 1999 01:3:21 0 July 1999 01:3:22 0 July 1999 01:3:23 0 July 1999 01:4:01 0 July 1999 01:4:02 0 July 1999 01:4:03 0 July 1999 01:4:04 0 July 1999 01:4:05 0 July 1999 Action

Index of Current Pages 00:0:02

CB/CFE/CFi Service Manual
Page No. Rev. Date 01:4:06 0 July 1999 01:4:07 0 July 1999 02:1:01 1 September 1999 02:1:02 1 September 1999 02:1:03 1 September 1999 02:1:04 1 September 1999 02:1:05 0 January 1999 02:1:06 0 January 1999 02:2:01 0 May 1999 02:3:01 0 July 1999 02:3:02 0 July 1999 03:1:01 0 January 1999 03:1:02 0 January 1999 03:1:03 0 January 1999 03:1:04 0 January 1999 03:2:01 0 May 1999 03:3:01 0 July 1999 03:3:02 0 July 1999 04:1:01 0 January 1999 04:1:02 0 January 1999 04:1:03 0 January 1999 04:1:04 0 January 1999 04:2:01 0 May 1999 04:3:01 0 July 1999 04:3:02 0 July 1999 05:1:01 0 January 1999 05:1:02 0 January 1999 05:1:03 0 January 1999 05:1:04 0 January 1999 05:1:05 0 January 1999 05:1:06 0 January 1999 05:2:01 0 May 1999 05:3:01 0 July 1999 05:3:02 0 July 1999 06:1:01 0 May 1999 06:1:02 0 January 1999 06:1:03 0 January 1999 06:1:04 0 January 1999 06:1:05 0 January 1999 06:1:06 0 January 1999 06:1:07 0 January 1999 06:1:08 0 January 1999 06:2:01 0 May 1999 06:3:01 0 July 1999 06:3:02 0 July 1999 07:1:01 0 March 2000 07:1:02 0 March 2000 07:3:01 0 March 2000 08:1:01 0 January 1999 Action

exchange exchange

exchange exchange

Revision 3

December 2000

Carl Zeiss
Page No. Rev. 08:1:02 0 08:1:03 1 08:1:04 1 08:1:05 0 08:1:06 0 08:2:01 0 08:3:01 0 08:3:02 1 09:1:01 0 09:1:02 0 09:1:03 0 09:1:04 0 09:1:05 0 09:1:06 0 09:2:01 0 09:3:01 0 09:3:02 0 10:1:01 0 10:1:02 0 10:1:03 0 10:1:04 0 10:2:01 0 10:3:01 0 10:3:02 1 11:1:01 0 11:1:02 0 11:1:03 0 11:1:04 0 11:1:05 0 11:1:06 0 11:2:01 0 11:3:01 0 11:3:02 0 12:1:01 0 12:1:02 0 12:1:03 0 12:1:04 0 12:2:01 0 12:3:01 0 12:3:02 0 13:1:01 0 13:1:02 0 13:1:03 0 13:1:04 0 13:2:01 0 13:3:01 0 13:3:02 1 14:1:01 0 14:1:02 0 Date January 1999 March 2000 March 2000 January 1999 January 1999 May 1999 July 1999 March 2000 January 1999 January 1999 January 1999 January 1999 January 1999 January 1999 May 1999 July 1999 July 1999 May 1999 January 1999 January 1999 January 1999 May 1999 July 1999 March 2000 May 1999 January 1999 January 1999 January 1999 January 1999 January 1999 May 1999 July 1999 July 1999 January 1999 January 1999 January 1999 January 1999 May 1999 July 1999 July 1999 May 1999 January 1999 January 1999 January 1999 May 1999 July 1999 March 2000 May 1999 January 1999 Action

Index of Current Pages 00:0:03

CB/CFE/CFi Service Manual
Page No. Rev. 14:1:03 1 14:1:04 1 14:2:01 0 14:3:01 0 14:3:02 0 15:1:01 0 15:1:02 0 15:3:01 0 Date March 2000 March 2000 May 1999 July 1999 July 1999 March 2000 March 2000 March 2000 Action

Revision 2

December 2000

Carl Zeiss
Pos No. Pcs
1 2 3 4a 4b 5 6 7a 7b 8 9 10 1 1 1 1 1 1 1 1 1 1 1 1

Planar 2,8/80 CB
Spare Part No. Description
102165-0011-180 102165-0012-030 102212-8105-000 000000-1018-370 102212-0011-000 102212-0001-000 102212-8106-000 000000-1018-373 102212-0006-000 102212-0016-000 Front lens guard Engraved ring Snap ring Front lens element Front lens element Lens holding ring Front lens Rear lens element Rear lens element Rear lens Lens holding ring Rear lens guard

01:1:01

Remark
VHAB Code No. 51643

replace it by the same type (without groove) replace it by the same type (with groove)

replace it by the same type (without groove) replace it by the same type (with groove)

VHAB Code No. 50377

Revision 0

January 1999

Planar 2,8/80 CB
5

6

01:1:02

3 10 2 4a/b 1 9 8

7a/b 4a

7a

4b
marked with grooves

7b

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs
1 2 3 4 5 6 7 8 9 10 11 12 13 14 4 1 1 1 1 1 1+1 1 1 2 1 1 1 1

Planar 2,8/80 CB
Spare Part No. Description
000000-0069-933 102211-1059-000 102212-1058-000 102211-1542-000 100349-1539 010 109950-0389-000 109950-0623-000 109950-0390-000 102211-1177-000 000000-0098-765 102211-1057-000 102211-1056-000 102211-1522-000 000000-1008-959 Screw Holding disk Holding ring Grip ring Setting ring Spring for setting notch Ball Notched ring Clutch lever Screw Clutch spring Notch spring Notch knob Diaphragm clutch ring

01:1:03

Remark

Revision 0

January 1999

Planar 2,8/80 CB
10 9 6 5 4 3 2 1 7 8 10 11 12 7 13 14

01:1:04

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs
1 2 3 4a 4b 1 3 1 1 1

Planar 2,8/80 CB
Spare Part No. Description
102211-1054-000 000000-0400-789 102212-1744-010 000000-1033-343 000000-1033-344 Stop down ring Screw Depth of field ring Case + shutter mount Case + shutter mount

01:1:05

Remark

replace it by the same type (lens elements without grooves) replace it by the same type (lens elements with grooves) Pos No. 4a/b has to be exchanged together with shutter mount

5 6 7 8 9 10 11 12 13

1 1 1 1 1 1 1 2 1

109950-0378-000 102211-8620-000 109951-0042-000 109950-0626-000 000000-0088-208 102211-8675-000 102211-8553-000 000000-0190-005 102211-1829-000

Cover plate Flash housing Countersunk screw Nut Screw Flash contact, riveted Stop down handle Countersunk screw Spring for stop down ring

Revision 0

January 1999

Planar 2,8/80 CB
5 4a/b

01:1:06

3 2 1

6 8 10 9 7

11 13 12

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs
1 2 3a 3b 1 1 1 1

Planar 2,8/80 CB
Spare Part No. Description
102212-8602-000 102211-1037-000 000000-1033-343 000000-1033-344 Shutter unit Intermediate stop down ring Shutter mount + case Shutter mount + case

01:1:07

Remark
replace it by the same type (lens elements without grooves) replace it by the same type (lens elements with grooves) Pos No. 3a/b has to be exchanged together with case

4 5 6 7 8 9 10

3 2 2 1 1 1 1

000000-0096-457 000000-0088-598 102211-1068-000 102211-1067-000 102211-1910-000 109950-0334-000 102211-1062-000

Screw Screw Stop ring Intermediate telescope shaft Bracket Pinion for cocking shaft Cam

Revision 0

January 1999

Planar 2,8/80 CB

01:1:08

4 3a/b

2 7 1 8 9 10 5 6

6

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 5 1 1 5 1 1 1 6+4 1 1 1 1 1 1 1 1 1 1

Planar 2,8/80 CB
Spare Part No. Description
102211-1026-010 000000-0069-908 102211-1036-000 109950-0327-000 000000-0088-598 102211-8574-000 102211-1020-000 109950-0320-000 000000-0088-598 000000-1008-958 109950-0344-000 102211-1072-000 102212-8900-000 109950-0341-000 000000-1008-957 109950-0342-000 109950-0114-000 000000-0093-536 109950-0343-000 Focusing ring Screw Focusing grip ring Clamp ring Screw Focusing mount Bearing Guide bar Screw Bayonet plate Guide bar Light tunnel Contact dummy Holding plate Telescope shaft Latch Latch spring Screw Latch bearing screw

01:1:09

Remark

Revision 0

May 1999

Planar 2,8/80 CB
11 10 8 9 5

01:1:10
12

7 6 5 4 3 13 2 1 14 16 19 17 18 15

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs
1 2 3 4 5 6 7a 7b 7c 8 9 10 11 12 13 14 15 16 17a 17b 18a 18b 19 20 21 22 23 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1

Planar 2,8/80 CB
Spare Part No. Description
109950-0611-000 109950-0702-000 109950-0703-000 109950-0370-000 109950-0619-000 109950-0617-000 109950-0614-000 109950-0615-000 109950-0616-000 000000-1026-076 102211-1515-000 109950-0369-000 109950-0007-000 109950-0624-000 109950-0368-000 109950-0363-000 109950-0037-000 109950-0064-XXX 000000-1008-960 000000-1109-777 109950-0371-000 000000-1109-776 109950-0707-000 000000-0093-536 109950-0004-000 109950-0013-000 109950-0734-000 Securing ring Cam ring Cocking ring Cocking ring spring Speed lever spring Speed lever screw Speed lever Speed lever Speed lever Cocking gear Drive spring 1 Drive Screw Bridge Drive spring 2 Spring for blade opening ring Closing spring Cocking shaft Spring for intermediate cocking gear Spring for intermediate cocking gear Intermediate cocking gear Intermediate cocking gear Retard gear train Screw Countersunk screw Cylinder head rivet Flash contact spring

01:1:11

Remark

Selection stage III, 2 notches Selection stage II, 1 notch Selection stage without notch

see repair instructions

16 selection stages (XXX=000...160, see repair instructions) replace it together with Pos. 18a (old version) replace it together with Pos. 18b (new version) replace it together with Pos. 17a (old version) replace it together with Pos. 17b (new version)

Revision 1

December 2000

Planar 2,8/80 CB
15 14

01:1:12

13 12 11

10 9 8 5 4 3 18 a/b 2 19 1 21 20 17 a/b 6 7a/b/c 16

22

23

Revision 1

December 2000

Carl Zeiss
Pos No. Pcs
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1 1 3 1 3 1 5 1 1 5 1 1 1 1 1 3 1

Planar 2,8/80 CB
Spare Part No. Description
109950-0362-000 109950-0365-000 109950-0361-000 109950-0604-000 109950-0032-000 109950-0854-000 109950-0348-000 109950-8024-000 000000-1033-458 109950-0815-000 109950-0358-000 109950-0705-000 109950-0704-000 109950-0042-000 000000-0069-975 000000-0093-538 109950-0364-000 Blade opening ring Blade Blade Tap screw Countersunk screw Blade cover disc Diaphragm blade Diaphragm disc Case Countersunk screw Base plate Blade ring Mount tube Stop plate Screw Screw Blade

01:1:13

Remark

Revision 0

January 1999

Planar 2,8/80 CB
8 7

01:1:14
9 10

6 4 5

3 2 1

17 11 16 12 13 15 14

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs
1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 1 1 1 1 1 1 1 1 1 1 1 1 2

Planar 2,8/80 CB
Spare Part No. Description
109950-0353-000 109950-0649-000 109950-0350-000 109950-0352-000 102211-1108-000 109950-0355-000 102211-8548-000 109950-0833-000 102211-8528-000 102211-1766-000 000000-1026-108 109950-0366-000 102211-1150-000 000000-0190-005 Fixing screw Collar screw Diaphragm lever Diaphram lever screw Diaphragm ring Securing ring Control ring Opening lever spring Securing ring 2 Override pawl spring Diaphragm spring Locking lever spring Locking pawl Countersunk screw

01:1:15

Remark

Revision 0

January 1999

Planar 2,8/80 CB
8 7

01:1:16
9

6 5 4 3 2 1 10

11 12

13 14
Revision 0 January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 V-2180 V-2223 000000-1033-916 109950-0716-000 109950-0723-000 109950-0724-000 109950-0722-000 109950-0718-000 109950-0715-000 109950-0719-000 109950-0713-000 109950-0750-000 109950-0688-000 109950-0721-000 109950-0725-000 109950-0726-000 102165-0000-901 102212-8105-901 102212-8106-901

Tools
Former Tool No.
1450/8 493 916 and 109950-0712-000 1450/8 385 614 1450/8 386 818 1450/8 386 821 1450/8 386 806 1450/8 385 638 1450/8 385 602 1450/8 385 641 1450/8 385 588 1450/8 416 115 1450/8 387 176 1450/8 386 795 1450/8 386 833 1450/8 386 845 -

01:2:01
Remark

Description
Measuring device for planartrueness and concentricity Standard gauge Diaphragm setting gauge with gauge pivot Grooved ring wrench for X-contact Cocking button Cocking and release key Cocking and release key Control pawl and retard gear train bending tool Locking lever adjuster Control lever latch bending tool Diaphragm setting key Auxiliary cam Centering pin Auxiliary ring Retard lever pin bending tool Retard lever pin bending tool Wrench for engraved ring Wrench for front element Wrench for rear element

only for CFE and CFi lenses only for CFE and CFi lenses

for repair with open shutter for adjustment of 1/15s for adjustment of 1/500s

Revision 0

May 1999

Carl Zeiss
General

Repair Instruction 01:3:01

Fig. 01:3:01/1

General instructions for repair works
It is recommended to do a receipt inspection before starting repair works. Additional faults could be recognized and the appearance of the faults could give hints to consequential damages. After any repair work a final inspection has to be done.

General instructions for repair works on the barrel
Only screws with securing adhesive are mentioned in the text. All other screws are screwed in
without securing adhesive.

The flash contact must be free of lubricant. The shutter blades and the diaphragm blades and their bearing points must be free of
lubricant.

Lubrication of shutter parts only according to "Lubrication Plan". It is recommended to change the drive spring 1 (Spare Part No. 102211-1515-000) doing repair
works on the shutter unit. Please see repair instructions "Exchange of drive spring 1".

For works at the printed circuit boards of the CFE lenses: to avoid damages of the IC's from
electostatic discharge observe the general instructions for ESD prevention.

Check of shutter speed. Cock the shutter, actuate stop-down handle, rotate smoothly the diaphragm ring and check at
the same time whether the diaphragm blades open easily, consistently and fully. Close the diaphragm; diaphragm blades should move consistently and jerk-free. Release stop-down handle; diaphragm blades should open fully. Check flash contact. After repair works check dimensions related to lens bayonet flange, planartrueness and concentricity (Tool No. V-2180). Check functions with standard gauge (Tool No. V-2223). See instructions for standard gauge. Check lens adjustment with collimator. For maximum optical performance MTF equipment is recommended to use.

Revision 0

July 1999

Carl Zeiss
General

Repair Instruction 01:3:02

Check of planartrueness, concentricity, and flange focal length Lens Flange L1 focal length 74.9 0.05 26 0.015 74.9 0.05 26 0.015 74.9 0.05 26 0.02 74.9 0.05 26 0.02 74.9 0.05 26 0.015 74.9 0.05 26 0.015 74.9 0.05 26 0.015 74.9 0.05 26 0.015 74.9 0.1 26 0.02 74.9 0.1 26 0.015 74.9 0.1 26 0.02 L2 CC max. 31 31 68.8 68.8 65.6 31 43.1 65.6 57.3 65.5 80.9 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 PL Threads Version

Planar Planar Tessar Tessar Makro-Planar Planar Planar Makro-Planar Sonnar Sonnar Sonnar

2,8/80 2,8/80 4,8/160 4,8/160 4/120 2,8/80 3,5/100 4/120 4/150 4/180 5,6/250

CB CB CB CB CB CFE CFi CFi CFi CFi CFi

0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015 0.015

trapezoidal metric trapezoidal metric metric trapezoidal metric metric metric metric metric

a (01:1:02) b (01:1:02) a (02:1:02) b (02:1:02)

Threads metric trapezoidal

TH1 M42x0.75 TG41.5x1.5

D1 42.1 41.7

TH2 M33.5x0.5 TG33.5x1.5

D2 33.6 33.7

L2

Flange focal length (distance to film plane)

A CC A

D1 TH1

B

L1

TH2 D2 PL B

Fig. 01:3:02/1

Revision 0

July 1999

Carl Zeiss
General
Lens Flange focal length 74.9 0.05 74.9 0.05 74.9 0.05 74.9 0.05 L1

Repair Instruction 01:3:03
L2 max. 31.9 36.6 49.5 32.4 L3 CC PL

Distagon Distagon F-Distagon Distagon

3,5/60 4/40 3,5/30 4/50

CB CFE CFi CFi

26.9 0.01 26.9 0.01 26.9 0.01 26.9 0.01

38.5 20.6 31.4 20.6

0.005 0.005 0.005 0.01

0.01 0.005 0.005 0.01

L3

L2

Flange focal length (distance to film plane)

CC A A 38.1 M38x0.5 M33.5x0.5 33.6 B
July 1999

cap ring L1

PL B

Fig. 01:3:03/1

Revision 0

Carl Zeiss
General

Repair Instruction 01:3:04

Cleaning and exchange of lens elements
Use a suction lifter for removing of lens elements. The surface of the lens elements has to be cleaned before mounting. The following tools are necessary for dismounting and mounting of lens elements:

Front lens element / Front lens Unscrew engraved ring (snap ring is snapped in from the rear) Unscrew front lens element Unscrew lens holding ring Remove front lens Assembly is carried out in the reverse sequence analogously.

Tool No. 102165-0000-901 102212-8105-901

Rear lens element / Rear lens Unscrew rear lens element Unscrew lens holding ring Remove rear lens Assembly is carried out in the reverse sequence analogously.

Tool No.

102212-8106-901

Revision 0

July 1999

Carl Zeiss
General
Removal of shutter unit


Repair Instruction 01:3:05

Remove lens elements. Release shutter. Unscrew 4 screws of holding disk (from the front). Remove holding disk. Remove setting ring (mind the ball and spring of the notch). Remove diaphragm clutch ring and notched ring. Unscrew stop down handle. Remove spring and stop down ring. Unscrew 3 screws (01:3:05/1-1) of depth of field ring and one for grounding of flash contact (01:3:05/1-2), and remove depth of field ring. Unscrew one countersunk screw (01:3:05/1-3), one cylinder head screw (01:3:05/4) and remove case. Unscrew 3 screws from the back (at the shining surface). Remove shutter unit from the front. Assembly is carried out in the reverse sequence analogously (mind the ball in the setting ring).

1 2

3

1

1

4
Fig. 01:3:05/1

Revision 0

July 1999

Carl Zeiss
General

Repair Instruction 01:3:06

Recommendation: Mark position of cocking shaft before disassembly of cocking ring (otherwise index will be disoriented by 1 tooth).

1

2

3

1 Borehole 2 Intermediate cocking gear 3 Cocking shaft 4 Mark 5 Index 6 Spring for intermediate cocking gear 7 Spring suspension rivet

7

6

5

4

Fig. 01:3:06/1

Test planartrueness and concentricity after fixing of case.

Removal of flash socket
Snap out flash housing from the inside of depth of field ring with a wide screw driver. Unscrew nut with special tool (Tool No. 109950-0716-000, Former Tool No. 1450/8 385 614). For assembly, the nut has to be secured.

Removal of bayonet plate and focusing ring
Release shutter. Snap out light tunnel. Unscrew 5 screws (mind the different length of 2 and 3). Remove focusing assembly by drawing it over the stop of the telescope shaft. Remove grip ring. Loosen 5 clamp screws around the focusing ring. Remove focusing ring.

Revision 0

July 1999

Carl Zeiss
General
Exchange of telescope shaft:

Repair Instruction 01:3:07

Clinch the screw (01:3:07/1-1) from the outside after assembly.

1
Fig. 01:3:07/1 Screw in (for example after cleaning) of focusing mount is possible in any thread (For focal lengths 40, 50, 60, 80). Assembly is carried out in the reverse sequence analogously. Push the bayonet plate over the bearing and fix the screws under axial pressure. Mind the order.

1

2

3

4

6
Fig. 01:3:07/2

5

Slip the focusing ring over the threaded ring and turn it clockwise until the stop. Fix the clamp screws and mind the order (see section "Adjustment of the focusing ring").

Revision 0

July 1999

Carl Zeiss
General

Repair Instruction 01:3:08

Screw focusing assembly onto the case (all 5 screws have to be secured). Mind the right position of the notch of the telescope shaft.

Fig. 01:3:08/1 Insert the telescope shaft and push it over the stop.

Dismounting of Case
See "Disassembly of shutter unit". See "Removal of bayonet plate and focusing ring". For assembly mind the position of the cam and the pinion. Turn the cam until the inner face of the pinion is in parallel to the outside and the face of the cam is at an angle of 40 towards the center line.

40

Fig. 01:3:08/2

Adjustment of the focusing ring
Remove the focusing grip ring. Set the focusing ring at . Loosen 5 clamp screws. Turn away focusing ring by approx. 45 from the stop and secure by one clamp screw..

Revision 0

//

July 1999

Carl Zeiss
General

Repair Instruction 01:3:09

Adjust by turning the focusing ring. Loosen the clamp screw and turn focusing ring towards the -stop. Tighten all clamp screws (mind the order).

1

Index on the focusing ring

5

4

3
Fig. 01:3:09/1

2

Disassembly of shutter unit
Exchange of blades and blade opening ring Dismount securing ring and cam ring. Recommendation: Mark position of cocking pinion. Dismount cocking ring with cocking ring spring. Remove speed lever spring. Dismount securing ring 2 and control ring from the back of the shutter. Dismount securing ring 1 and diaphragm ring.

Exchange of shutter blades Mind the sequence of inserting the shutter blades (view from camera bayonet).

Bent upwards

Bent downwards

Fig. 01:3:09/2

Revision 0

July 1999

Carl Zeiss
General
Exchange of blade opening ring Remove spring for blade opening ring from the front. Remove blade opening ring.

Repair Instruction 01:3:10

Exchange of diaphragm blades Remove control pawl spring and diaphragm spring. Open diaphragm fully. Unscrew screws of blade cover disc (3 standard screws, 1 special screw). Remove blade cover disc. Dismount diaphragm blades.

Assembly is carried out in the reverse sequence analogously.

4

5

3
Bore marks for inner diameter Special screw
Fig. 01:3:10/1 Fig. 01:3:10/2

1 2

Insert centering pin (Tool No. 109950-0688-000, Former Tool No. 1450/8 387 176) through the case into the plastic bush of the cocking pinion when tightening the screws of the base plate. Test the function of the override latch at the control ring. The baffle plate spring (01:3:10/3-1) has to latch (01:3:10/3-2) when the blades extend into the opening diameter at least for approx. 0.2-0.3 mm.

0.2 - 0.3 mm

2

1

Fig. 01:3:10/3

Fig. 01:3:10/4

Revision 0

July 1999

Carl Zeiss
General
Exchange of base plate

Repair Instruction 01:3:11

See "Exchange of blades and blade opening ring". Dismount driving spring 1 from the front. Dismount drive. Dismount bridge. Dismount driving spring 2. Open shutter by twisting the blade ring. Dismount retard gear train (2 screws). Dismount cocking pinion, intermediate cocking gear and spring for intermediate cocking gear. Dismount speed lever Dismount mount tube. Dismount closing spring for blade ring. Remove blade ring.

Assembly is carried out in the reverse sequence analogously. Secure screws of mount tube and stop plate with two component adhesive.

Secured

Secured

Fig. 01:3:11/1

Revision 0

July 1999

Carl Zeiss
General
Exchange of cocking shaft

Repair Instruction 01:3:12

Special tools: V-2223 Standard gauge 109950-0721-000 Auxiliary ring Assortment of 16 different cocking shafts 109950-0064-XXX

(XXX = 000-160)

Insert intermediate cocking gear (01:3:12/1-6) together with spring (01:3:12/1-3). Spring for intermediate cocking gear has to rest against the spring suspension rivet (01:3:12/1-1). Pre-cock intermediate cocking gear, until its boring (01:3:12/1-2) points to the center of the spring suspension rivet (01:3:12/1-1). Insert (anyone of assortment) cocking shaft (01:3:12/1-4) in a way, that the index (01:3:12/1-5) points to the center of intermediate cocking gear (clearance for one of the shutter blades). Tension the shutter slowly by the gauge lever and make sure the cocking shaft starts to rotate before position No. 11marked out on tool V-2223. In case the cocking shaft starts to rotate later than No. 11, select another shaft out of the assortment. (see: "Recommendation: Mark position of cocking shaft.")

6 5

1 Spring suspension rivet 2 Borehole 3 Spring for intermediate cocking gear 4 Cocking shaft 5 Index 6 Intermediate cocking gear

1

2

3

4

Fig. 01:3:12/1

Revision 0

July 1999

Carl Zeiss
General
Exchange of drive spring 1

Repair Instruction 01:3:13

It is recommended to change the drive spring 1 doing repair works on the shutter unit. Lubricate well inside diameter of drive spring with Lubricant K. Hang in short leg at Pos. 01:3:13/1-1.

Pos. 1

Drive spring 1

Fig. 01:3:13/1

Exchange of bridge Special Tools: 109950-0721-000 Auxiliary ring 109950-0715-000 Locking lever adjuster When mounting the bridge (01:3:13/2-1), make sure that the nose (01:3:13/2-3) of the locking lever (01:3:13/2-2) suspended by the cocking ring (01:3:13/2-5) will fall it at the drive (01:3:13/2-4) by at least 0.5 mm. In case of deviation: Bend locking lever (01:3:13/2-2) as required for the right engaging depth with the locking lever adjustment tool (A = Point of application for the locking lever adjuster).

1

A

2

3

4 5

1 Bridge 2 Locking lever 3 Nose of locking lever 4 Drive 5 Cocking ring

min 0.5 mm
Fig. 01:3:13/2

Revision 0

July 1999

Carl Zeiss
General
Checking of flash contact

Repair Instruction 01:3:14

In released position the opening width of contact must be 0.5 mm. The contact must close approx. 1 mm before the shutter is fully opened.

0.5 mm

1 mm
Fig. 01:3:14/1

Revision 0

July 1999

Carl Zeiss
General
Exchange of the retard gear train

Repair Instruction 01:3:15

Special Tools: 109950-0726-000 Retard lever pin bending tool 109950-0725-000 Retard lever pin bending tool 109950-0718-000 Control pawl and retard gear train bending tool Turn the blade ring (01:3:15/1-8) at the switch off hook for escapement 2 (01:3:15/1-2) towards the drive (01:3:15/1-9). Fit in retard gear train (01:3:15/1-3), press slightly towards the center against the tube mount (01:3:15/1-6) and screw tight. Adjust control fin (01:3:15/1-5) of the escapement lever 2 in a way that the escapement 2 (01:3:15/1-2) touches the tube mount (01:3:15/1-6) when it is switched off. Fit the cam ring (must be fitted before the speeds can be checked). Check 1/30 s. In case of deviation: Loosen both screws (01:3:15/1-1) (01:3:15/1-4) and revolve the retard gear train around screw (01:3:15/1-4). Towards tube mount Away from tube mount = = prolongation of time shortening of time

After adjustment, tighten both screws firmly.
1/30 s +

-

1 2 3

9

4

8
6

5

7
1 Screw 2 Escapement 2 3 Retard gear train 4 Screw (Revolving point) 5 Control fin for escapement 2 6 tube mount 7 Switch off hook 8 Blade ring 9 Drive

Fig. 01:3:15/1

Revision 0

July 1999

Carl Zeiss
General

Repair Instruction 01:3:16

Check 1/125 s. The control fin (01:3:16/1-3) must rest against the center side of the control cam. In case of deviation: Adjust speed by bending the adjusting pin (01:3:16/1-1). Towards tube mount Away from tube mount = = shortening of time prolongation of time

2 3 1 +
1 Adjusting pin 2 Cam ring 3 Control fin

1/125 s

Fig. 01:3:16/1

Check 1/500 s. In case of deviation: Bend retard lever pin (01:3:16/2-1) to such a degree, that the retard lever is disengaged by the cam ring (01:3:16/2-2) and the drive can work without resistance.

2

1

1 Retard lever pin 2 Cam ring

1/500 s

Fig. 01:3:16/2

Revision 1

January 2000

Carl Zeiss
General

Repair Instruction 01:3:17

Check 1 s. In case of deviation: Bend tongue (01:3:17/1-1) for escapement 1 (01:3:17/1-2) as far as required. Mind catch of escapement (01:3:17/2).

1

Escapement 1 Engagement 1/3 - 2/3

+

-

2

2

free

Fig 01:3:17/1

Fig. 01:3:17/2

Check 1/8 s and 1/15 s formed by escapement 2. In case of deviation: Bend tongue (01:3:17/3-1) for escapement 2 (01:3:17/3-2) as far as required. Mind catch of escapement (01:3:17/4).

1

Escapement 1 Engagement 1/3 - 2/3

+

-

2
Fig. 01:3:17/3

free
Fig. 01:3:17/4

2

Check remaining shutter speeds, if necessary adjust values by chiseling or filing the control cam.

Revision 0

July 1999

Carl Zeiss
General
Shutter speed table Nominal speed Upper limit DIN 19015 Upper limit Carl Zeiss Nominal speed Lower limit Carl Zeiss Lower limit DIN 19015 Tolerance Carl Zeiss Tolerance DIN 19015 s ms ms ms ms ms EV EV 1 1231 1149 1000 871 812 1/2 616 574 500 435 406 1/4 308 287 250 218 203 1/8 154 144 125 109 102

Repair Instruction 01:3:18

1/15 76.9 71.8 62.5 54.4 50.8

1/30 38.5 35.9 31.3 27.2 25.4

1/60 19.24 17.95 15.63 13.6 12.69

1/125 1/250 9.62 8.97 7.81 6.8 6.35 5.34 4.68 3.91 3.26 2.86

1/500 2.67 2.34 1.95 1.63 1.43

0.2 0.3

0.26 0.45

Revision 0

July 1999

Carl Zeiss

Repair Instruction 01:3:19

Additional instructions for CFE and CFi type lenses
The shutter blades and the diaphragm blades are opened when the shutter is cocked and the setting ring is in "F-position". As long as the release knob of the camera is pressed the diaphragm blades stay closed at the preset position.

F-adjustment Special Tools: 109950-0750-000 Auxiliary cam

Note! The shutter must be separated from the barrel. Mount auxiliary cam. Using shutter speed setting from 1/500s to B, the diaphragm will remain closed after operating sequence. Using the F-setting, the diaphragm opens fully after operating sequence. Turn cocking ring (01:3:19/1-1) until rivet (01:3:19/1-4), on control lever (01:3:19/1-2) comes to be positioned just before the peak point of the cam. In this position, control latch (01:3:19/1-5) must fall in at the control lever by 0.5 mm and arrest it. If necessary, correct by bending fin (01:3:19/1-3).

1

0.5 mm

1 Cocking ring 2 Control lever 3 Fin 4 Rivet 5 Control latch

5
Fig. 01:3:19/1

4

3

2

Revision 0

July 1999

Carl Zeiss

Repair Instruction 01:3:20

Additional instructions for CFE and CFi type lenses
Adjustment of diaphragm switch lever Special Tools: V-2223 Standard gauge 109950-0718-000 Control pawl and retard gear train bending tool 109950-0750-000 Auxiliary cam Select B-position. Mount auxiliary cam Check shutter with standard gauge. Check that there is a clearance of 0.1 0.2 mm between the diaphragm switch lever (01:3:20/1-2) and the cocking ring (01:3:20/1-1). (A = Point of application for the control pawl and retard gear train bending tool).

B-position

1

1 Cocking ring 2 Diaphragm switch lever

2

0.1 - 0.2 mm A

Fig. 01:3:20/1

Revision 0

July 1999

Carl Zeiss

Repair Instruction 01:3:21

Additional instructions for CFE and CFi type lenses
Special Tools: V-2223 Standard gauge 109950-0718-000 Control pawl and retard gear train bending tool 109950-0719-000 Control lever latch bending tool Select F-position. Mount auxiliary cam. Adjust diaphragm switch lever (01:3:21/1-2) with the control pawl and retard gear train bending tool in a way that its nose does not touch the cocking ring (01:3:21/1-1). (A = Point of application for the control pawl and retard gear train bending tool) Make sure the diaphragm opens up within position No. 5 marked out on gauge V-2223. Adjust if necessary. (B = Point of application for the control lever latch bending tool)

F-position 1 free
1 Cocking ring 2 Diaphragm switch lever

2

B
Fig. 01:3:21/1

A

Revision 0

July 1999

Carl Zeiss

Repair Instruction 01:3:22
Link to: VHABSTS

Additional instructions for CFE type lenses
Adjustment of circuit board position for F-stop indication

Mount the lens on a camera body 202, 203 or 205. Make sure that the preset F-stop value corresponds (lens/camera body). If not, loosen the 3 screws (01:3:22/1-1) and reset the printed circuit board (01:3:22/1-2) accordingly. Tighten the screws and recheck. Repeat until F-stop setting and camera display corresponds.

1

1 Screws 2 Printed circuit board

2

Fig. 01:3:22/1

Revision 0

July 1999

Carl Zeiss
Focusing mount 102211-8574-000 Used for the following types: Planar Distagon Distagon Distagon 2,8/80 4/40 4/50 3,5/60

Repair Instruction 01:3:23

Mounting and dismounting of focusing mount

Note! The threaded ring and the flange can be put together in any position. Make sure that the measurement 4.5 0.2 mm is achieved by rotating the focusing mount parts (01:3:23/1-1) against each other.

2

1

1 Focusing mount 2 Bearing ring

4.5 0.2 mm

Fig. 01:3:23/1

Revision 0

July 1999

Carl Zeiss
General

Lubrication Plan 01:4:01

Lubricants other than those given in the lubrication chart must not be used, for only the ones tested by us can guarantee safe operation. Grease points of lubrication only slightly. Shining grey gears have been lubricated in a special procedure already when being manufactured and therefore never require any further lubrication. Lubricant Lubricant K Lubricant L Lubricant M Lubricant N Lubricant P Lubricant R Lubricant S Lubricant T Lubricant Y Order No. HB-K HB-L HB-M HB-N HB-P HB-R HB-S HB-T HB-Y

Revision 0

July 1999

Carl Zeiss
General

Lubrication Plan 01:4:02

Different types of telescope shafts

Fig. 01:4:02/1

Fig. 01:4:02/2

Fig. 01:4:02/3

HB - K HB - L

Fig. 01:4:02/4

Fig. 01:4:02/5

Fig. 01:4:02/6

Fig. 01:4:02/7

Revision 0

July 1999

Carl Zeiss
General

Lubrication Plan 01:4:03

Fig. 01:4:03/1

Fig. 01:4:03/2

HB - K HB - N HB - S

Fig. 01:4:03/3

Fig. 01:4:03/4

Revision 0

July 1999

Carl Zeiss
General

Lubrication Plan 01:4:04

Fig. 01:4:04/1

Fig. 01:4:04/2

Fig. 01:4:04/3

Fig. 01:4:04/4

HB - K HB - M HB - Y

Fig. 01:4:04/5

Revision 0

July 1999

Carl Zeiss
General
HB - K HB - M

Lubrication Plan 01:4:05

Fig. 01:4:05/1

Fig. 01:4:05/2

Fig. 01:4:05/3 CB lenses

Fig. 01:4:05/4 CFE/CFi lenses

Fig. 01:4:05/5

Fig. 01:4:05/6

Revision 0

July 1999

Carl Zeiss
General
focal length 30

Lubrication Plan 01:4:06

focal lengths 40, 50, 60

Fig. 01:4:06/1

Fig. 01:4:06/2

focal length 80

focal length 100

Fig. 01:4:06/3

HB - S HB - T

Fig. 01:4:06/4

Revision 0

July 1999

Carl Zeiss
General
focal lengths 120, 180

Lubrication Plan 01:4:07

focal length 150

Fig. 01:4:07/1 focal length 160

Fig. 01:4:07/2

HB - R

Fig. 01:4:07/3 focal length 250

Fig. 01:4:07/4

Revision 0

July 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7

Tessar 4,8/160 CB
Spare Part No.
102165-0011-160 102165-0012-040 102165-1010-000 100349-8105-000 100349-0111-000 100349-0001-010 100349-8106-000

02:1:01

Pcs
1 1 1 1 1 1 1

Description
Engraved ring Snap ring Bayonet Front lens element Lens holding ring Front lens Rear lens Element

Remark

Revision 1

September 1999

Tessar 4,8/160 CB
7

02:1:02

6 5

3 2 1

4

Revision 1

September 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Tessar 4,8/160 CB
Spare Part No.
100349-8058-000 000000-0095-550 100349-1590-010 100349-1744-010 100349-8601-000 000000-1033-343 109950-0592-000 100349-1072-000 000000-0069-974 000000-1015-939 109950-0644-000 000000-0093-535 000000-1015-953 000000-1015-960 000000-1015-961 000000-1015-942 000000-0098-795 000000-1015-947

02:1:03

Pcs
1 1 1 1 1 1 1 1 5 1 1 4 1 1 1 1 2 1

Description
Holding ring Roll pin Diaphragm clutch ring Depth of field ring Shutter unit Shutter mount + case Telescope bush Light tunnel Screw Bayonet plate Telescope shaft Screw Focusing mount Guide bar Guide bar Stop Screw M1,7x1,5 Focusing ring

Remark

Revision 1

September 1999

Tessar 4,8/160 CB
4 3

5

6 7

02:1:04

2 1

12

15

8 9 10 17 16 11

14

13

18

Revision 1

September 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6

Tessar 4,8/160 CB
Spare Part No.
109950-0417-000 109950-0034-000 109950-0755-000 109950-0128-000 109950-0416-000 100349-8601-000

02:1:05

Pcs
1 3 1 1 1 1

Description
Blade Opening Ring Blade Blade Blade Blade Cover Disc Shutter Unit

Remark

Revision 0

January 1999

Tessar 4,8/160 CB
6

02:1:06

5

2 3 2

1

4 2

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 1 1 102212-8105-901 102212-8106-901

Tessar 4,8/160 CB
Former Tool No.
-

02:2:01
Remark

Description
Wrench for front element Wrench for rear element

Revision 0

May 1999

Carl Zeiss
Tessar 4,8/160 CB

Repair Instruction 02:3:01

Fig. 02:3:01/1

Revision 0

July 1999

Carl Zeiss
Recommendation:

Repair Instruction 02:3:02

Mounting and dismounting of focusing mount
Before dismounting the focusing mount mark the positions between the three parts.

Focusing mount 000000-1015-953 Used for the following type: Tessar 4,8/160

Screw together threaded ring (02:3:02/2-1) and flange (02:3:02/2-2) until face (Pos. B) is even. Fit in both parts into the carrier (02:3:02/2-3) according to 02:3:02/1 and screw in until the end. Mount one guide bar (turn the carrier to fit in the threads) and measure dimension A. In case of deviation: Dismount guide bar, unscrew threaded ring and flange and screw them into the next thread.

ca. 10

Fig. 02:3:02/1

2 +0.5 mm

A

1

2

3

Pos. B

1 Threaded ring 2 Flange 3 Carrier

Fig. 02:3:02/2

Revision 0

July 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7

Distagon 3,5/60 CB
Spare Part No.
102165-0011-200 102165-1010-000 102165-0012-010 104940-0011-000 104852-0001-010 104869-0018-000 104852-0107-000

03:1:01

Pcs
1 1 1 1 1 1 1

Description
Engraved ring Bayonet Snap ring Lens holding ring Front lens Lens holding ring Rear lens

Remark

Revision 0

January 1999

Distagon 3,5/60 CB

03:1:02

5 4 7

6

3 2

1

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8

Distagon 3,5/60 CB
Spare Part No.
104940-8058-000 000000-0095-550 100349-1539-010 104940-1590-010 104940-1744-010 102212-8602-000 000000-1033-344 104940-1026-010

03:1:03

Pcs
1 1 1 1 1 1 1 1

Description
Holding ring Roll pin Setting ring Diaphragm clutch ring Depth of field ring Shutter unit Shutter mount + case Focusing ring

Remark

Details: look at 1:1:11 - 1:1:16 has to be exchanged together with case

Revision 0

January 1999

Distagon 3,5/60 CB
6

7

03:1:04

5

4 3 8 2 1

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 3 1 1 1 000000-1054-350 000000-1054-351 000000-1054-352

Distagon 3,5/60 CB
Former Tool No.
104869-8005-905 104869-8006-902 104869-8007-902

03:2:01
Remark

Description
Wrench for front element Wrench for center element Wrench for rear element

Revision 0

May 1999

Carl Zeiss
Distagon 3,5/60 CB

Repair Instruction 03:3:01

Fig. 03:3:01/1

Revision 0

July 1999

Carl Zeiss
Focusing mount 102211-8574-000 Used for the following types: Distagon Distagon Distagon Planar 3,5/60 4/40 4/50 2,8/80

Repair Instruction 03:3:02

Mounting and dismounting of focusing mount

Note! The threaded ring and the flange can be put together in any position. Make sure that the measurement 4.5 0.2 mm is achieved by rotating the focusing mount parts (03:3:02/1-1) against each other.

2

1

1 Focusing mount 2 Bearing ring

4.5 0.2 mm

Fig. 03:3:02/1

Revision 0

July 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8

Makro-Planar 4/120 CB
Spare Part No.
102165-0011-310 107836-0016-000 000000-1004-983 107836-0011-000 107836-0001-000 000000-1005-010 107836-0006-000 107836-0015-000

04:1:01

Pcs
1 1 1 1 1 1 1 1

Description
Engraved ring Snap ring Front lens element Lens holding ring Front lens Rear lens element Rear lens Lens holding ring

Remark

Revision 0

January 1999

Makro-Planar 4/120 CB
4

5

04:1:02
8

2 7 1

3

6

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Makro-Planar 4/120 CB
Spare Part No.
000000-1034-202 000000-1034-206 100349-8601-000 000000-1033-344 109950-0592-000 000000-1034-203 000000-0069-974 000000-1015-939 109950-0644-000 000000-0093-535 000000-1034-207 000000-1034-208 000000-1034-209 000000-1034-204 000000-0098-795 000000-1034-205

04:1:03

Pcs
1 1 1 1 1 1 5 1 1 4 1 1 1 1 2 1

Description
Diaphragm clutch ring Depth of field ring Shutter unit Shutter mount + case Telescope bush Light tunnel Screw Bayonet plate Telescope shaft Screw Guide bar Guide bar Focusing mount, compl. Stop Screw Focusing ring

Remark
Details: look at 2:1:5 - 2:1:6 has to be exchanged together with case

Revision 0

January 1999

Makro-Planar 4/120 CB
3

4

04:1:04
5 10

2

1 6 7

8 9

14 15 12

11

13

16

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 1 1 000000-1054-355 000000-1054-356

Makro-Planar 4/120 CB
Former Tool No.
107836-8004-906 107836-8005-906

04:2:01
Remark

Description
Wrench for front element Wrench for rear element

Revision 0

May 1999

Carl Zeiss
Makro-Planar 4/120 CB

Repair Instruction 04:3:01

Fig. 04:3:01/1

Revision 0

July 1999

Carl Zeiss
Recommendation:

Repair Instruction 04:3:02

Mounting and dismounting of focusing mount
Before dismounting the focusing mount mark the positions between the three parts.

Focusing mount 000000-1034-209 Used for the following types: Makro-Planar Sonnar 4/120 4/180



Screw together threaded ring (04:3:02/2-1) and flange (04:3:02/2-2) until face (Pos. B) is even. Fit in both parts into the carrier (04:3:02/2-3) according to 04:3:02/1 and screw in until the end. Mount one guide bar (turn the carrier to fit in the threads) and measure dimension A. In case of deviation: Dismount guide bar, unscrew threaded ring and flange and screw them into the next thread. =

or one thread

Fig. 04:3:02/1

2 +0.5 mm

A

1

2

3

Pos. B

1 Threaded ring 2 Flange 3 Carrier

Fig. 04:3:02/2
Revision 0 July 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8

Planar 2,8/80 CFE
Spare Part No.
102165-0011-180 102165-0012-030 102210-0014-000 102076-0101-000 102210-8005-000 102210-8006-000 102076-0107-000 102210-0019-000

05:1:01
Remark

Pcs
1 1 1 1 1 1 1 1

Description
Engraved ring Snap ring Lens holding ring Front lens Front lens element Rear lens element Rear lens Lens holding ring

Revision 0

January 1999

Planar 2,8/80 CFE
7

05:1:02
8

6

4 3

2

1

5

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12

Planar 2,8/80 CFE
Spare Part No.
000000-1034-425 000000-1034-426 000000-1034-427 102211-1590-010 000000-1034-428 000000-1034-432 000000-1034-433 000000-1034-434 000000-1034-429 000000-1034-431 200 509 000000-0093-535

05:1:03
Remark

Pcs
1 1 1 1 1 1 1 1 1 3 1 3

Description
Holding ring Setting ring F-knob Diaphragm clutch ring Depth of field ring Case + shutter mount Shutter unit Contact finger plate Contact finger for stop down Spacer bolt Printed circuit board Screw

has to be exchanged together with shutter mount

VHAB Spare Part No.

Revision 0

January 1999

Planar 2,8/80 CFE
8 7

05:1:04
12

6 11 5 10 4 1 3 2

9

1

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10

Planar 2,8/80 CFE
Spare Part No.
109950-0652-000 000000-0007-701 109950-0651-000 109950-8050-000 109950-0706-000 102211-8551-000 109950-8049-000 000000-0064-668 109950-8048-000 109950-0650-000

05:1:05
Remark

Pcs
1 1 1 1 1 1 1 2 1 1

Description
Diaphragm switch lever Locking washer Control pawl spring Control pawl, riveted Base plate Case, riveted Control lever, riveted Locking washer F-locking lever F- and control lever spring

Revision 0

January 1999

Planar 2,8/80 CFE
8 7 10

05:1:06

6

5

9

4 3 2 1

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 1 1 000000-1054-353 102210-8006-902

Planar 2,8/80 CFE
Former Tool No.
102210-8005-901 -

05:2:01
Remark

Description
Wrench for front element Wrench for rear element

Revision 0

May 1999

Carl Zeiss
Planar 2,8/80 CFE

Repair Instruction 05:3:01

Fig. 05:3:01/1

Revision 0

July 1999

Carl Zeiss
Focusing mount 102211-8574-000 Used for the following types: Planar Distagon Distagon Distagon 2,8/80 4/40 4/50 3,5/60

Repair Instruction 05:3:02

Mounting and dismounting of focusing mount

Note! The threaded ring and the flange can be put together in any position. Make sure that the measurement 4.5 0.2 mm is achieved by rotating the focusing mount parts (05:3:02/1-1) against each other.

2

1

1 Focusing mount 2 Bearing ring

4.5 0.2 mm

Fig. 05:3:02/1

Revision 0

July 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7

Distagon 4/40 CFE
Spare Part No.
000000-0088-598 109950-0667-000 104878-0016-020 104878-0001-000 104878-0027-000 104878-0011-000

06:1:01
Remark
VHAB Code No. 51654

Pcs
1 4 1 1 1 1 1

Description
Front lens guard Screw Grooved ring Engraved ring Front lens Lens holding ring Rear lens

Revision 0

May 1999

Distagon 4/40 CFE
5 4

06:1:02

3 7 2 1

6

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 3 1 1 3 3 1 1 3 1 1 3 1 3 3 1 1

Distagon 4/40 CFE
Spare Part No.
000000-0093-535 000000-1034-672 109950-0466-000 109950-0468-000 000000-0004-810 109950-0464-000 000000-1034-673 000000-0093-538 102211-1542-000 000000-1034-678 000000-0007-054 109950-0462-000 109951-0042-000 000000-1034-674 000000-0007-290 000000-0007-238

06:1:03
Remark

Description
Screw Tube Bearing Pressure spring Ball Grooved ring Index ring Screw Focusing grip ring Thread flange, fitted Threaded pin Retaining ring Screw Stop screw Notched cylinder pin Notched cylinder pin

Revision 0

January 1999

Distagon 4/40 CFE

06:1:04
10 14 13 12 11 15 16

9 8 7 6 5

4 3

2 1

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Distagon 4/40 CFE
Spare Part No.
000000-1034-668 107882-8560-000 000000-1034-426 000000-1034-427 000000-1034-669 000000-1034-670 000000-1034-793 000000-1034-675 000000-1034-793 000000-1034-671 000000-1042-424 000000-1042-423 000000-1034-429 000000-1034-676 000000-1034-431 200 502 000000-0093-535

06:1:05
Remark

Pcs
1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1

Description
Holding ring Snap in spring, riveted Setting ring F-knob Diaphragm clutch ring Depth of field ring Case + shutter mount Shutter unit Shutter mount + case Focusing ring Telescope shaft Bayonet plate Contact finger for stop down Contact finger plate Spacer bolt Printed circuit board Screw

has to be exchanged together with shutter mount has to be exchanged together with case

VHAB Spare Part No.

Revision 0

January 1999

Distagon 4/40 CFE
6 5 4

7

06:1:06
17

14 3 13

2

1 16

15

12

11

10 9 8
Revision 0 January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11

Distagon 4/40 CFE
Spare Part No.
109950-0652-000 000000-0007-701 109950-0651-000 109950-8050-000 109950-0706-000 109950-8055-000 102211-8551-000 109950-8049-000 000000-0064-668 109950-8048-000 109950-0650-000

06:1:07
Remark

Pcs
1 1 1 1 1 5 1 1 2 1 1

Description
Diaphragm switch lever Locking washer Control pawl spring Control pawl, riveted Base plate Shutter blade Case, riveted Control lever, riveted Locking washer F-locking lever F- and control lever spring

Revision 0

January 1999

Distagon 4/40 CFE
9 8 7

06:1:08
11

9 10 6

5

4 3 2 1

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 3 4 1 1 1 1 104878-8005-907 104878-8006-913 000000-1030-049 104878-8007-901

Distagon 4/40 CFE
Former Tool No.
-

06:2:01
Remark

Description
Wrench for front element Wrench for center element Wrench for rear element Wrench for retaining ring

Revision 0

May 1999

Carl Zeiss
Distagon 4/40 CFE

Repair Instruction 06:3:01

Fig. 06:3:01/1

Revision 0

July 1999

Carl Zeiss
Focusing mount 102211-8574-000 Used for the following types: Distagon Distagon Distagon Planar 4/40 4/50 3,5/60 2,8/80

Repair Instruction 06:3:02

Mounting and dismounting of focusing mount

Note! The threaded ring and the flange can be put together in any position. Make sure that the measurement 4.5 0.2 mm is achieved by rotating the focusing mount parts (06:3:02/1-1) against each other.

2

1

1 Focusing mount 2 Bearing ring

4.5 0.2 mm

Fig. 06:3:02/1

Revision 0

July 1999

Carl Zeiss
Pos No. Pcs
1 2 3 4 5 6 7 1 2 1 1 2 4 1 104549-1037-000 104549-1036-000 30 763 829 755 829 790 100349-1072-000

Tele-Superachromat 5,6/350 CFE
Spare Part No. Description
Front lens guard Rubber knob Focusing grip ring Tripod plate Screw Screw Light tunnel

07:1:01

Remark
VHAB Code No. 51654 (not figured)

VHAB Spare Part No. VHAB Spare Part No. (not figured) VHAB Spare Part No. (not figured) (not figured)

Revision 0

March 2000

Tele-Superachromat 5,6/350 CFE

07:1:02

2

3

Carl Zeiss Tele-Superachromat 5,6/350



7
Nr 0000000

5

4

6

Revision 0

March 2000

Carl Zeiss

Repair Instruction 07:3:01

Tele-Superachromat 5,6/350 CFE

Carl Zeiss Tele-Superachromat 5,6/350



Nr 0000000

Fig. 07:3:01/1

Each lens has been adjusted individually. Repair works may not be carried out with the exception of the replacement of the parts mentioned in the spare part list of this lens. In case of damage please send the complete lens to: Carl Zeiss D-73446 Oberkochen

Revision 0

March 2000

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 7 7 7 8 9 10 11

F-Distagon 3,5/30 CFi
Spare Part No.
104877-0012-010 104813-0101-010 104813-0039-000 000000-0069-911 104877-0011-000 104813-8010-000 104813-8011-000 104813-8012-000 104813-8013-000 000000-1010-224 000000-0089-029 101025-0217-000 104813-0008-000

08:1:01
Remark
VHAB Code No. 50709

Pcs
1 1 1 1 1 1 1 1 1 1 1 4 1 1

Description
Front lens guard Lens holding ring Front lens Washer Screw Washer Neutral glass Filter Or 57 Filter Y 50 Filter B 11 Flange Screw Lens holding ring Rear lens

Revision 0

January 1999

F-Distagon 3,5/30 CFi
5 4 6

7

8

9

08:1:02

3 2

1

10 11

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15a 15b 16a 16b 17 18 19 20 21

F-Distagon 3,5/30 CFi
Spare Part No.
000000-0069-908 109950-0503-000 000000-1038-875 000000-1038-864 000000-0098-468 000000-1038-863 109950-0498-000 109950-0497-000 000000-0007-283 000000-1038-865 000000-0069-911 109950-0501-000 000000-0050-208 109950-0494-000 000000-0069-933 000000-1099-929 000000-1038-866 000000-1099-917 000000-0069-933 107882-8560-000 000000-0004-814 109950-0502-000 000000-0069-921

08:1:03
Remark
has to be exchanged together with Pos No. 14

Pcs
4 1 1 1 3 1 1 1 1 1 2 1 1 1 4 4 1 1 4 1 1 1 1

Description
Screw Bayonet ring Threaded ring Rubber ring Screw Index ring Spring Lever Cylinder pin Ring Screw Stop Cylinder pin Tube Screw Screw Holding ring Holding ring Screw Snap in spring Ball Flat spring Screw

has to be exchanged together with Pos No. 3 replace it by the same type (cheese head screw) replace it by the same type (countersunk screw) replace it by the same type (for cheese head screws) replace it by the same type (for countersunk screws)

Revision 1

March 2000

F-Distagon 3,5/30 CFi
14 13 11 10 9 8 7 6 5 12

17 16a/b 15a/b

18

08:1:04

4 3 2 1

19 20 21

Revision 1

March 2000

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

F-Distagon 3,5/30 CFi
Spare Part No.
000000-1034-426 000000-1034-427 000000-1038-867 000000-1038-868 000000-1034-793 000000-1034-675 000000-1034-793 109950-0594-000 000000-1038-869 000000-0069-974 000000-1015-939 000000-1026-109 000000-1038-871 000000-0093-535 000000-1038-872 000000-1038-873 000000-1038-874 000000-0098-795 109950-0481-000

08:1:05
Remark

Pcs
1 1 1 1 1 1 1 1 1 5 1 1 1 4 1 1 1 2 1

Description
Setting ring F-knob Diaphragm clutch ring Depth of field ring Case + shutter mount Shutter unit Shutter mount + case Telescope bush Light tunnel Screw Bayonet plate Telescope shaft Focusing mount, complete Screw Guide bar Guide bar Focusing ring Screw Stop

has to be exchanged together with shutter mount Details: look at 06:1:07 - 06:1:08 has to be exchanged together with case

Revision 0

January 1999

F-Distagon 3,5/30 CFi
5

6

7

8

08:1:06

4 3 2 1 10 11 12 19 18 15 16 14 9

13

17

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 1 1 000000-1054-348 000000-1054-347

F-Distagon 3,5/30 CFi
Former Tool No.
104813-8007-901 104877-8003-904

08:2:01
Remark

Description
Wrench for center element Wrench for rear element

Revision 0

May 1999

Carl Zeiss
F-Distagon 3,5/30 CFi

Repair Instruction 08:3:01

Fig. 08:3:01/1

Revision 0

July 1999

Carl Zeiss
Recommendation:

Repair Instruction 08:3:02

Mounting and dismounting of focusing mount
Before dismounting the focusing mount mark the positions between the three parts.

Focusing mount 000000-1038-871 Used for the following type: F-Distagon 3,5/30

Screw together threaded ring (08:3:02/1-1) and flange (08:3:02/1-2) until the total length is 33.3 0.05 mm. Measure dimension C of flange (08:3:02/1-2). If dimension C = 20.0 mm Fit in flange (08:3:02/1-2) according to 08:3:02/2. If dimension C = 17.5 mm Fit in flange (08:3:02/1-2) according to 08:3:02/3. Mount one guide bar (turn the carrier to fit in the treads) and measure dimension A. In case of deviation: Dismount guide bar, unscrew flange (08:3:02/1-2) and screw it into the next thread.
33.3 0.05 mm

A

6.15 0.5 mm

1 2 3

1 Threaded ring 2 Flange 3 Carrier

C
Fig. 08:3:02/1

one thread

one thread

Fig. 08:3:02/2
Revision 1

Fig. 08:3:02/3
March 2000

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8

Distagon 4/50 CFi
Spare Part No.
102165-0011-370 104908-0022-000 104931-1010-000 000000-0083-974 000000-0069-940 104908-0011-000 104908-0001-010 104908-0023-000

09:1:01
Remark

Pcs
1 1 1 3 3 1 1 1

Description
Engraved ring Snap ring Bayonet Screw Washer Lens holding ring Front lens Transfer ring

Revision 0

January 1999

Distagon 4/50 CFi
7 6 4 5

8

09:1:02

3 2 1

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14

Distagon 4/50 CFi
Spare Part No.
000000-1038-878 109950-0468-000 000000-0004-810 102211-1542-000 000000-0093-538 000000-1038-879 109950-0462-000 000000-0088-598 109950-0760-000 109951-0042-000 000000-1034-674 000000-0007-290 000000-0007-238 000000-1038-880

09:1:03
Remark

Pcs
1 3 3 1 3 1 1 2 1 3 3 1 1 1

Description
Intermediate ring Pressure spring Ball Grip ring Screw Index ring Fixing ring Screw Guide angle Screw Stop screw Pin Pin Threaded flange, fitted

Revision 0

January 1999

Distagon 4/50 CFi
9 8 7 10

09:1:04
11 12 13

6 5

4

2 1

3

14

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13

Distagon 4/50 CFi
Spare Part No.
000000-1034-668 107882-8560-000 000000-1034-426 000000-1034-427 000000-1038-881 000000-1038-882 000000-1034-793 000000-1034-675 000000-1034-793 000000-1038-883 000000-1038-884 000000-1038-885 000000-1038-886

09:1:05
Remark

Pcs
1 1 1 1 1 1 1 1 1 1 1 1 1

Description
Holding ring Snap in spring Setting ring F-knob Diaphragm ring Depth of field ring Case + shutter mount Shutter unit Shutter mount + case Focusing ring Bayonet plate Telescope shaft Intermediate telescope shaft

has to be exchanged together with shutter mount Details: look at 06:1:07 - 06:1:08 has to be exchanged together with case

Revision 0

January 1999

Distagon 4/50 CFi
10

09:1:06

9 8 7 6 12 11

5 4 13 3 2 1

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 3 4 1 1 1 1 000000-1037-017 104908-8003-907 000000-1054-349 104878-8007-901

Distagon 4/50 CFi
Former Tool No.
104908-8105-901 -

09:2:01
Remark

Description
Wrench for front element Wrench for center element Wrench for rear element Wrench for retaining ring

Revision 0

May 1999

Carl Zeiss
Distagon 4/50 CFi

Repair Instruction 09:3:01

Fig. 09:3:01/1

Revision 0

July 1999

Carl Zeiss
Focusing mount 102211-8574-000 Used for the following types: Distagon Distagon Distagon Planar 4/50 4/40 3,5/60 2,8/80

Repair Instruction 09:3:02

Mounting and dismounting of focusing mount

Note! The threaded ring and the flange can be put together in any position. Make sure that the measurement 4.5 0.2 mm is achieved by rotating the focusing mount parts (09:3:02/1-1) against each other.

2

1

1 Focusing mount 2 Bearing ring

4.5 0.2 mm

Fig. 09:3:02/1

Revision 0

July 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8

Planar 3,5/100 CFi
Spare Part No.
000000-1010-362 102165-0012-030 102166-8105-000 102165-0014-000 102111-0001-000 000000-1010-366 102111-0105-000 102111-0020-000

10:1:01
Remark

Pcs
1 1 1 1 1 1 1 1

Description
Engraved ring Snap ring Front lens element Lens holding ring Front lens Rear lens element Rear lens Lens holding ring

Revision 0

May 1999

Planar 3,5/100 CFi

10:1:02
6

8 7

3

2

1

5 4

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Planar 3,5/100 CFi
Spare Part No.
000000-1034-425 000000-1034-426 000000-1034-427 000000-1038-867 000000-1038-951 000000-1034-793 000000-1034-433 000000-1034-793 109950-0594-000 000000-1038-869 000000-0069-974 000000-1015-939 109950-0806-000 000000-1038-952 000000-1038-872 000000-0093-535 000000-1038-873 000000-1038-874 000000-0098-795 109950-0481-000

10:1:03
Remark

Pcs
1 1 1 1 1 1 1 1 1 1 5 1 1 1 1 4 1 1 2 1

Description
Holding ring Setting ring F-knob Diaphragm clutch ring Depth of field ring Case + shutter mount Shutter unit Shutter mount + case Telescope bush Light tunnel Screw Bayonet plate Telescope shaft Focusing mount, complete Guide bar Screw Guide bar Focusing ring Screw Stop

has to be exchanged together with shutter mount Details: look at 05:1:05 - 05:1:06 has to be exchanged together with case

Revision 0

January 1999

Planar 3,5/100 CFi
6

8 7

10:1:04

5 9 4 3 2 10 1 12 13 15 16 17 11

20 19

14

18

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 1 1 102165-8005-906 000000-1054-354

Planar 3,5/100 CFi
Former Tool No.
102166-8006-903

10:2:01
Remark

Description
Wrench for front element Wrench for rear element

Revision 0

May 1999

Carl Zeiss
Planar 3,5/100 CFi

Repair Instruction 10:3:01

Fig. 10:3:01/1

Revision 0

July 1999

Carl Zeiss
Recommendation:

Repair Instruction 10:3:02

Mounting and dismounting of focusing mount
Before dismounting the focusing mount mark the positions between the three parts.

Focusing mount 000000-1038-952 Used for the following type: Planar 3,5/100

Screw together threaded ring (10:3:02/1-1) and flange (10:3:02/1-2) until the total length is 28 0.05 mm. Fit in flange (10:3:02/1-2) according to 10:3:02/2. Mount one guide bar (turn the carrier to fit in the threads) and measure dimension A. In case of deviation: Dismount guide bar, unscrew flange (10:3:02/1-2) and screw it into the next thread.
28 0.05 mm

A

4.0 +0.5 mm

1 2 3

1 Threaded ring 2 Flange 3 Carrier

one thread
Fig. 10:3:02/1

Fig. 10:3:02/2

Revision 1

March 2000

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8

Makro-Planar 4/120 CFi
Spare Part No.
102165-0011-310 107836-0016-000 000000-1004-983 107836-0011-000 107836-0001-010 000000-1005-010 107836-0006-000 107836-0015-000

11:1:01

Pcs
1 1 1 1 1 1 1 1

Description
Engraved ring Snap ring Front lens element Lens holding ring Front lens Rear lens element Rear lens Lens holding ring

Remark

Revision 0

May 1999

Makro-Planar 4/120 CFi

11:1:02
6

8 7

3

2 1

5 4

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Makro-Planar 4/120 CFi
Spare Part No.
000000-1034-425 000000-1034-426 000000-1034-427 000000-1034-202 000000-1039-083 000000-1034-793 000000-1039-085 000000-1034-793 109950-0592-000 100349-1072-000 000000-0069-974 000000-1015-939 109950-0644-000 000000-0093-535 000000-1034-209 000000-1034-207 000000-1034-208 000000-1034-205 000000-1034-204 000000-0098-795

11:1:03

Pcs
1 1 1 1 1 1 1 1 1 1 5 1 1 4 1 1 1 1 1 2

Description
Holding ring Setting ring F-knob Diaphragm clutch ring Depth of field ring Case + shutter mount Shutter unit Shutter mount + case Telescope bush Light tunnel Screw Bayonet plate Telescope shaft Screw Focusing mount, complete Guide bar Guide bar Focusing ring Stop Screw

Remark

has to be exchanged together with shutter mount has to be exchanged together with case

Revision 0

January 1999

Makro-Planar 4/120 CFi
7 6

11:1:04
8

5 4 3 2 10 1 12 13 14 19 17 20 15 16 11 9

18

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Makro-Planar 4/120 CFi
Spare Part No.
109950-0652-000 000000-0007-701 109950-0651-000 109950-8050-000 109950-0359-000 109950-0417-000 109950-0128-000 109950-0034-000 109950-0755-000 109950-0416-000 102211-8551-000 109950-8049-000 000000-0064-668 109950-8048-000 109950-0650-000

11:1:05

Pcs
1 1 1 1 1 1 1 3 1 1 1 1 1+1 1 1

Description
Diaphragm switch lever Locking washer Control pawl spring Control pawl, riveted Base plate Blade opening ring Blade Blade Blade Blade cover Case, riveted Control lever, riveted Locking washer F-locking lever F- and control lever spring

Remark

Revision 0

January 1999

Makro-Planar 4/120 CFi
11

11:1:06

10 9 8 7

12

13

14

15

6

13

5

4 2 1 3

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 1 1 000000-1054-355 000000-1054-356

Makro-Planar 4/120 CFi
Former Tool No.
107836-8004-906 107836-8005-906

11:2:01
Remark

Description
Wrench for front element Wrench for rear element

Revision 0

May 1999

Carl Zeiss
Makro-Planar 4/120 CFi

Repair Instruction 11:3:01

Fig. 11:3:01/1

Revision 0

July 1999

Carl Zeiss
Recommendation:

Repair Instruction 11:3:02

Mounting and dismounting of focusing mount
Before dismounting the focusing mount mark the positions between the three parts.

Focusing mount 000000-1034-209 Used for the following types: Makro-Planar Sonnar 4/120 4/180



Screw together threaded ring (11:3:02/2-1) and flange (11:3:02/2-2) until face (Pos. B) is even. Fit in both parts into the carrier (11:3:02/2-3) according to 11:3:02/1 and screw in until the end. Mount one guide bar (turn the carrier to fit in the threads) and measure dimension A. In case of deviation: Dismount guide bar, unscrew threaded ring and flange and screw them into the next thread. =

or one thread

Fig. 11:3:02/1

2 +0.5 mm

A

1

2

3

Pos. B

1 Threaded ring 2 Flange 3 Carrier

Fig. 11:3:02/2
Revision 0 July 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9

Sonnar 4/150 CFi
Spare Part No.
102165-0011-355 107823-0012-020 102165-1010-000 101114-8005-000 101114-0014-000 101025-0301-000 000000-1010-397 101025-8121-010 101025-0217-000

12:1:01
Remark

Pcs
1 1 1 1 1 1 1 1 1

Description
Engraved ring Snap ring Bayonet Front lens element Lens holding ring Front lens Rear lens element Rear lens Lens holding ring

Revision 0

January 1999

Sonnar 4/150 CFi

12:1:02
7

9 8

4

3 2 1

6 5

Revision 0

January 1999

Carl Zeiss
Pos No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Sonnar 4/150 CFi
Spare Part No.
000000-1039-114 107882-8560-000 000000-1034-426 000000-1034-427 000000-1039-115 000000-1039-116 000000-1034-793 000000-1039-085 000000-1034-793 109950-0581-000 100349-1072-000 000000-0069-974 000000-1015-939 109950-0582-000 000000-1039-118 000000-1039-119 000000-0093-535 000000-1039-120 000000-1039-121 000000-0098-795 000000-1015-942

12:1:03
Remark

Pcs
1 1 1 1 1 1 1 1 1 1 1 5 1 1 1 1 4 1 1 2 1

Description
Holding ring Snap in spring Setting ring F-knob Diaphragm clutch ring Depth of field ring Case + shutter mount Shutter unit Shutter mount + case Telescope bush Light tunnel Screw Bayonet plate Telescope shaft Focusing mount, complete Guide bar Screw Guide bar Focusing ring Screw Stop

has to be exchanged together with shutter mount Details: look at 11:1:05 - 11:1:06 has to be exchanged together with case

Revision 0

January 1999

Sonnar 4/150 CFi
7 6

12:1:04
8 9 10

5 4 3 2 12 1 13 21 20 16 17 18 14

11

15 19

Revision 0

January 1999

Carl Zeiss
Pos No. Pcs Tool No.
1 2 1 1 101114-8005-902 101025-0000-924

Sonnar 4/150 CFi
Former Tool No.
-

12:2:01
Remark

Description
Wrench for front element Wrench for rear element

Revision 0

May 1999

Carl Zeiss
Sonnar 4/150 CFi

Repair Instruction 12:3:01

Fig. 12:3:01/1

Revision 0

July 1999

Carl Zeiss
Recommendation:

Repair Instruction 12:3:02

Mounting and dismounting of focusing mount
Before dismounting the focusing mount mark the positions between the three parts.

Focusing mount 000000-1039-118 Used for the following type: Sonnar 4/150

Screw together threaded ring (12:3:02/2-1) and flange (12:3:02/2-2) until face (Pos. B) is even. Fit in both parts into the carrier (12:3:02/2-3) according to 12:3:02/1 and screw in until the end. Mo