Text preview for : DEH_12_1300.pdf part of pioneer deh12a manuals for cd player deh12a
Back to : DEH_12_1300.part1.rar | Home
Service Manual
DEH-1300/X1M/UC
ORDER NO.
CRT2557
HIGH POWER CD PLAYER WITH FM/AM TUNER
DEH-1300 DEH-12
X1M/UC
- This service manual should be used together with the following manual(s):
Model No. CX-958 Order No. CRT2423
X1M/UC
Mech. Module Remarks S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly
CONTENTS
1. 2. 3. 4. 5. 6. SAFETY INFORMATION ............................................2 EXPLODED VIEWS AND PARTS LIST .......................2 BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .....8 PCB CONNECTION DIAGRAM ................................24 ELECTRICAL PARTS LIST ........................................32 ADJUSTMENT..........................................................36 7. GENERAL INFORMATION .......................................40 7.1 DIAGNOSIS ........................................................40 7.1.1 TEST MODE ..............................................40 7.1.2 DISASSEMBLY .........................................43 7.1.3 CONNECTOR FUNCTION DESCRIPTION .......47 7.2 PARTS .................................................................48 7.2.1 IC................................................................48 7.2.2 DISPLAY ....................................................54 7.3 OPERATIONAL FLOW CHART ...........................55 8. OPERATIONS AND SPECIFICATIONS.....................56
PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A. PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936 C PIONEER CORPORATION 2000
K-ZZA. OCT. 2000 Printed in Japan
DEH-1300,12
- CD Player Service Precautions
1. For pickup unit(CXX1285) handling, please refer to"Disassembly"(see page 43). During replacement, handling precautions shall be taken to prevent an electrostatic discharge(protection by a short pin). 2. During disassembly, be sure to turn the power off since an internal IC might be destroyed when a connector is plugged or unplugged. 3. Please checking the grating after changing the service pickup unit(see page 38).
1. SAFETY INFORMATION
CAUTION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do so and refer the repair to a qualified service technician. WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 - Proposition 65
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
4 8 2 9 7 6 5 3
11
14 1
15 10
13
12
2
DEH-1300,12
NOTE:
- Parts marked by "*" are generally unavailable because they are not in our Master Spare Parts List. - Screws adjacent to mark on the product are used for disassembly.
(1) PACKING SECTION PARTS LIST
Mark No. Description 1 2 3 4 5 6 7 8 9 10 Cord Assy Spring Screw Polyethylene Bag Screw Screw Polyethylene Bag Handle Bush Polyethylene Bag Part No. CDE6468 CBH1650 CBA1002 CEG-127 CRZ50P090FMC TRZ50P080FMC CEG-158 CNC5395 CNV3930 CEG1173 Mark No. Description 11-1 11-2 11-3 * 11-4 12 ····· Owner's Manual Installation Manual Card Carton Part No. CRD3279 CRD3280 ARY1048
See Contrast table(2) See Contrast table(2)
*
*
13 Contain Box 14 Protector 15 Protector
CHP2346 CHP2347
(2) CONTRAST TABLE DEH-1300/X1M/UC and DEH-12/X1M/UC are constructed the same except for the following:
Part No. Mark No. Symbol and Description DEH-1300/X1M/UC DEH-12/X1M/UC 12 Carton CHG4160 CHG4161 13 Contain Box CHL4160 CHL4161
- Owner's Manual, Installation Manual
Model DEH-1300/X1M/UC DEH-12/X1M/UC Part No. CRD3279 CRD3280 Language English, French, Spanish
3
DEH-1300,12
2.2 EXTERIOR
B
A
4
DEH-1300,12
(1) EXTERIOR SECTION PARTS LIST
Mark No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34-42 43 Tuner Amp Unit Screw Screw Screw FM/AM Tuner Unit Holder Pin Jack(CN301) Terminal(CN403) Plug(CN901) Connector(CN601) Connector(CN605) Antenna Jack(CN402) Holder Holder Holder Heat Sink Screw Cover Holder Grille Unit Screw Screw Screw Cable Cord Assy Fuse(10A)
CD Mechanism Module(S8.1)
Part No. CWM7296 ASZ26P080FMC BPZ26P080FMC BSZ26P160FMC CWE1563 CNC8815 CKB1041 CKF1059 CKM1330 CKS3581 CKS3838 CKX1056 CNC8041 CNC8043 CNC9128 CNR1589 BPZ20P080FZK CNM6975 CNV6479
See Contrast table(2)
Mark No. Description 44 45-47 48 49 50 51 52 53 54, 55 56 57 58 59 60 61 62 63 64 65 66 Chassis Unit ····· Button(+/-, EQ, LD) Button(1-6, CLK) Button(A, B) Button(EJECT/BSM) Button(CROSS) Button(SOURCE) ····· Keyboard Unit LCD Connector(CN1801) Holder Sheet Lighting Conductor Lighting Conductor Rubber Rubber ····· Holder Unit
Part No. CXB4625 CAC6821 CAC6822 CAC6823 CAC6824 CAC6825 CAC6851
See Contrast table(2)
CAW1633 CKS3580 CNC9078 CNM7057 CNV6475 CNV6476 CNV6477 CNV6478 CXB6681 ISS26P055FUC TDA7386 2SD2396
BSZ26P060FMC BSZ30P060FMC BSZ30P120FMC CDE6160 CDE6468 CEK1136 CXK5203 CNC5704 CNC9127 CNM5210 CNM6224 CNM6386 CNS6344 CXB4033
67 Screw 68 IC(IC302) 69 Transistor(Q904, 981)
Holder Cover Cushion Insulator Insulator Panel ····· Case Unit
(2) CONTRAST TABLE DEH-1300/X1M/UC and DEH-12/X1M/UC are constructed the same except for the following:
Part No. Mark No. Symbol and Description DEH-1300/X1M/UC DEH-12/X1M/UC 20 Grille Unit CXB7188 CXB7189 56 Keyboard Unit CWM7310 CWM7309
5
DEH-1300,12
2.3 CD MECHANISM MODULE
D
C
6
DEH-1300,12
- CD MECHANISM MODULE SECTION PARTS LIST
Mark No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Control Unit Connector(CN802) Connector(CN801) Connector(CN701) Connector(CN101) Screw Screw Screw(M2x3) Screw(M2x5) Screw Screw(M2x4) Washer Washer Washer ····· Spring Spring Spring Spring Spring Spring ····· Spring Spring Spring Spring Spring Spring Spring Spring Bracket Spring Connector Connector Shaft Screw(M2.6x6) Frame Frame Lever Arm Bracket ····· Spacer Sheet ····· Part No. CWX2411 CKS2192 CKS2193 CKS2773 CKS3486 BMZ20P030FMC BSZ20P040FMC CBA1077 EBA1028 CBA1243 CBA1362 CBF1037 CBF1038 CBF1060 Mark No. Description 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 ····· Ball Belt Roller Arm Arm Arm Arm Guide Guide Gear Gear Guide Damper Arm Arm Arm Guide Guide ····· Guide Clamper Gear Motor Unit(M1) Screw Unit Chassis Unit Gear Unit Arm Unit Motor Unit(M2) Lever Unit Arm Unit Motor Unit(M3) Arm Unit Bracket Unit Screw Screw Washer Pickup Unit(Service)(P8) Screw PCB Photo-transistor(Q1, 2) Damper Rack Spring Part No. CNR1189 CNT1086 CNV4509 CNV6037 CNV5247 CNV5248 CNV5249 CNV5254 CNV5255 CNV5257 CNV5256 CNV6272 CNV6174 CNV6096 CNV6031 CNV6211 CNV6012 CNV5510
CBH2079 CBH2117 CBH2314 CBH2110 CBH2282 CBH2318 CBH2324 CBH2118 CBH2161 CBH2163 CBH2189 CBH2377 CBH2260 CBH2262 CNC8568 CBL1369 CDE5531 CDE5532 CLA3894 CBA1458 CNC8565 CNC8749 CNC9265 CNC8663 CNC8567 CNM3315 CNM6659
CNV5751 CNV6013 CNV5813 CXB2190 CXB5892 CXB4797 CXB4728 CXB5753 CXB2195 CXB4730 CXB4731 CXB2562 CXB4732 CXB4795 JFZ20P025FMC JGZ17P025FZK YE20FUC CXX1285 IMS26P030FMC CNX2982 CPT230SX-TU CNV6175 CNV6014 CBH2315
*
7
1
2
3
4
DEH-1300,12
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
A TUNER AMP UNIT
A
FM/AM TUNER UNIT
ANTENNA CN402 28 AMANT
AMRF ATT
FM/AM 1ST IF 10.7MHz T51 Q51 CF51 CF52 CF53
MPXREF 41kHz AMDET IC 2 FM MPX
L ch 6 R ch 5
ANT ADJ
FMANT
IC1 MIXER, IF AMP, DET.
COMP LDET
21 18
27 RFGND 26
ATT FMRF CF202 IMG ADJ AM 2ND IF X901 450kHz 10.25MHz
WC NC NC
IC 3 EEPROM
FMLOCL SDBW DGND FMSD DI/DO NL1 NL2 4 CE2 CE1 STIND 1 PDIO CN701
NC
CK
LOCH 23 25
LOCL
PDIO
PCE2
PCK
PCE1
SL
LOCL
VCC
VDD
B
PICKUP UNIT(SERVICE)(P8)
LD MD
LD+ MD
C
CONTROL UNIT
Q101
98 LD L_OUT 16 CN605 CDL
CN101 14 5
SD
Q411
7 17 20 22 10 19 14
24
9
11 12 15 16
8
SL 13
RF ADJ
CREQ
VDD VCC
2
3
8
17
97
PD
HOLOGRAM UNIT FOCUS ACT TRACKING ACT
FO+ TO+ 4 3 FOP TOP
A+C/F B+D/E 24 X201 23
IC 201 UPD63711GC
IC 301 BA5985FM
16
RF-AMP, DSP, SERVO, DAC
TD/FD SD/MD 39
CD DRIVER
FOP 18 TOP
HOME
4
C
SPINDLE MOTOR
M
CN801
12 11
SOP SOM
S801 HOME
CARRIAGE MOTOR
M
1 2
14
LOADING MOTOR
M
3 4 CN802 3 1
COP 13 COM 10 LOP 9 LOM
FWD REV MUTE
1 28 21
CDLOAD CDEJET CONT
6 5 11
19 20 14
CDLOAD EJET CONT
EJTSNS DSCSNS CLAMP
22 23 21 24
3 2 4 1
EJTD DINC CLAMP
SELECT SENSE
2
VD D802 D801 S802 CLAMP VD
Q981
VD B.U
DISC SENSE
+5V REGULATOR
VDD 4
D
PHOTO UNIT(S8)
IC 701 BA05SFP
1
IN
2
Q982
CD5VON 7 18 CD5VON VDCONT
D
8 1 2 3 4
5
6
7
8
DEH-1300,12
A
CN301
REAR L CH Q346 SYSTEM CONTROLLER IC 601(1/2) PE5196A
6 76
SD SL
14 13 48 12 PDIO 11 57
PCE PCK TUNPCE2 PDO PDI LOCL VST VCK VDT
Q363
CN901
Q903
VDD B.U B.U
BACKUP FUSE 10A 2 1 GND
B
GND
BACK UP
2
IN2_L
VST/ VCK/ VDT
POWER AMP
23 FL-- FL+ RL-- RL+ 9 11 10 12
3
E.VOL FIE/EQ
IN3_L
Frontout_L Rearout_L
10 11
14
FL
IC 301 PML003AM
12 RL
IC 302 TDA7386
21 3 5
FL FL+ RL RL+
MUTE 22
STBY 4
Q350
Q351 MUTE Q902
asens bsens ACC 4 ACC B.U
ASENS
63
SYSPW
Q901
64
BSENS
SYSTEM CONTROLLER IC 601(2/2) PE5196A
31 34 23 SYSPW CDLOAD CDEJET CONT 42 B.U SYSPW 5 6 1 B.REM 5 B.REM
POWER SWITCH
C
IC970 TPD1018F
80 79 27
EJTSNS DSCSNS CLAMP
MUTE
44
B
KEYBOARD UNIT
CN601
CN1801
22
KYDT VDCONT DPDT
8 9
3 4 1 VDD 5
3 4
20 18
KYDT DPDT
LCD
RESET
60
RESET IC 602 S--80834ANY
2
VDD
5
56
VDD
SWVDD 35 CD5VON
41
10 VLCD
Q650
KEY CONT. LCD DRIVER KEY MATRIX IC 1801 PD6340A
D
22 X1801
23
9 5 6 7 8
1
2
3
4
DEH-1300,12
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)
Note: When ordering service parts, be sure to refer to "EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST".
A
A
A-a A-b
TUNER AMP UNIT
A-a
FM(100%):-19.5dBs AM(30%):-30dBs
Large size SCH diagram
FM/AM TUNER UNIT
CN402
A-a A-b
Guide page
A-a
A-b
Detailed page
272
DSP-201M-S00B
183
CN403
272
B
C
473
822
183
162
162
PE5196A
SYSTEM CONTROLLER
CN601
B
KEYBOARD UNIT
D
NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes: Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms *Capacitors Code Practical value 103 0.01µF 101/10 100µF/10V
10
A
1
2
3
4
5
6
7
8
DEH-1300,12
A-b
FM(100%):+3.6dBs AM(30%):-6.9dBs CD:+10.2dBs E.VOL FIE/EQ
CN301
A
CD:+9.4dBs
332/16
POWER AMP
CN901
NC
B
TDA7386
FM(100%):+29.6dBs AM(30%):+19.1dBs CD:+36.2dBs
>
CEK1136
600µH
RESET
331/16
C
A.SENS
B.SENS
CN605
CONTROL UNIT
CD:+4.1dBs
D
C
5
6
7
A
11
8
B
D A C
12
A-a A-b
DEH-1300,12
183
DSP-201M-S00B
CN403
183
162
162
A-a
FM/AM TUNER UNIT
FM(100%):-19.5dBs AM(30%):-30dBs
272 272
1
1
A
TUNER AMP UNIT
CN402
2
2
3
3
1
4
4
RESE
5
473
822
NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms *Capacitors Code Practical value 103 0.01µF 101/10 100µF/10V
C
A-a A-b
B C A
For resistors and capacitors in the circuit diagrams, their resistance values or capacitance values are expressed in codes:
CONTROL UNIT
5
2
PE5196A
SYSTEM CONTROLLER
6
6
CN601
B
7
KEYBOARD UNIT
7
DEH-1300,12
A-a
8
8
13
D
B
D A C
14
A-a A-b
DEH-1300,12
NC
POWER AMP
1
4 FM(100%):+29.6dBs AM(30%):+19.1dBs CD:+36.2dBs
TDA7386
332/16
A-b
FM(100%):+3.6dBs AM(30%):-6.9dBs CD:+10.2dBs CD:+9.4dBs
CN301 CN901
>
CEK1136
600µH
1
1
E.VOL FIE/EQ
2
2
3
3
4
CEK1136
600µH
331/16
RESET
5
C
CONTROL UNIT
5 A.SENS B.SENS CD:+4.1dBs
2
6
6
CN605
7
7 C
DEH-1300,12
A-b
A-a A-b
B A
8
8
15
D
1
2
3
4
DEH-1300,12
3.3 KEYBOARD UNIT
A
B
KEYBOARD UNIT
B
LCD DRIVER KEY CONTROLLER
C
LCD CAW1633
D
16
B
1
2
3
4
CLK
5
5
EQ LOUD BSM
6
6 R1708, 1710, 1712:181 (DEH-12/X1M/UC) R1708, 1710, 1712:151 (DEH-1300/X1M/UC) IL1801, 1802:CEL1638(14V 40mA) (DEH-12/X1M/UC) IL1801, 1802:CEL1651(14V 40mA) (DEH-1300/X1M/UC) D1701-1708:SML210DT (DEH-12/X1M/UC) D1701-1708:SML210PT (DEH-1300/X1M/UC)
7
7 C
DEH-1300,12
B
8
8
17
A
B A
CN601
D
1
2
3
4
DEH-1300,12
3.4 CD MECHANISM MODULE
A
C
PICKUP UNIT (SERVICE)(P8)
CONTROL UNIT
CN101
B
RF-AMP, SE
C
CL203IRXTU
CL203IRXTU
D
PHOTO UNIT(S8)
Q1 CPT230SX-TU Q2 CPT230SX-TU
CN802
SPINDLE MOTOR
M3 CXB2562 CARRIAGE MOTOR
M1 CXB2190
D
LOADING MOTOR
CD DRIVER
M2 CXB2195
CN801
18
C D
1
BA05SFP
5V REGULATOR
3 4
2
5
6
7
8
DEH-1300,12
A
SWITCHES: CONTROL UNIT S801 : HOME SWITCH.....ON-OFF S802 : CLAMP SWITCH....ON-OFF The underlined indicates the switch position.
B
MP, SERVO, DSP, DAC, LPF
CN701
C
A
CN605
D
5
6
7
C
8
19
DEH-1300,12
Note:1. The encircled numbers denote measuring pointes in the circuit diagram. 2. Reference voltage REFO:2.5V 1 CH1: RFI 1V/div. 0.5ms/div. 2 CH2: MIRR 5V/div. Test mode: Tracking open 1 CH1: RFI 1V/div. 0.5ms/div. 2 CH2: MIRR 5V/div. Normal mode: The defect part passes 800µm
- Waveforms
1 RFI 0.5V/div. 0.5µs/div. Normal mode: play
REFO REFO REFO REFO REFO
3 CH1: FD 0.5V/div. 0.2s/div. 4 CH2: FO+ 2V/div. Test mode: No disc, Focus close
3 CH1: FD 0.5V/div. 0.2s/div. 5 CH2: FOK 2V/div. Normal mode: Focus close
6 CH1: FE 0.5V/div. 1ms/div. 7 CH2: XSI 2V/div. Normal mode: Focus close
REFO REFO
REFO
REFO REFO REFO GND
8 CH1: TE 0.5V/div. 0.5ms/div. 9 CH2: TD 0.5V/div. Test mode: 32 tracks jump (FWD)
8 CH1: TE 0.5V/div. 0.5ms/div. 9 CH2: TD 0.5V/div. Test mode: Single jump (FWD)
8 CH1: TE 0.5V/div. 5ms/div. 9 CH2: TD 0.5V/div. Test mode: 100 tracks jump (FWD)
REFO
REFO
REFO
REFO
REFO
REFO
6 CH1: FE 0.1V/div. 3 CH2: FD 0.2V/div. Normal mode: Play
20ms/div.
3 CH1: FD 0.5V/div. 0.5s/div. 0 CH2: MD 1V/div. Normal mode: Focus close (12cm)
3 CH1: FD 0.5V/div. 0.5s/div. 0 CH2: MD 1V/div. Normal mode: Focus close (8cm)
REFO REFO
REFO
REFO
REFO
REFO
20
DEH-1300,12
8 CH1: TE 0.2V/div. 9 CH2: TD 0.2V/div. Normal mode: play
20ms/div.
8 CH1: TE 0.5V/div. 5ms/div. ! CH2: SD 0.5V/div. TEST mode: 100 Tracks jump(FWD)
0 MD
0.5V/div.
0.1s/div.
Normal mode: Play (12cm)
REFO REFO REFO
REFO
REFO
0 MD 1V/div. Normal mode: Long Search (12cm)
10ms/div.
@ EFM
1V/div.
5µs/div.
Normal mode: play
8 CH1: TE 1V/div. 2ms/div. # CH2: TEC 1V/div. Test mode: Focus close Tracking open
REFO REFO REFO REFO GND
8 CH1: TE 0.5V/div. 0.2s/div. 6 CH2: FE 0.5V/div. Normal mode: AGC after focus close
$ PLCK
2V/div.
0.5µs/div.
% SCKO
2V/div.
1µs/div.
Normal mode: play
Normal mode: play
REFO
REFO
REFO GND
REFO GND
^ Dout
2V/div.
10µs/div.
& LRCK
2V/div.
20µs/div.
* VD
5V/div.
50ms/div.
Normal mode: play
Normal mode: play
Normal mode: No disc
GND REFO GND REFO GND
21
DEH-1300,12
( CH1: R OUT 1V/div. 0.2ms/div. ) CH2: L OUT 1V/div. Normal mode: Play (1kHz 0dB)
6 CH1: FE 0.2V/div. 1ms/div. 3 CH2: FD 0.5V/div. Normal mode: During AGC
8 CH1: TE 0.2V/div. 1ms/div. 9 CH2: TD 0.5V/div. Normal mode: During AGC
REFO REFO REFO
REFO
REFO
REFO
1 CH1: RFI 1V/div. 0.5ms/div. / CH2: HOLD 5V/div. Normal mode: The defect part passes 800µm(B.D)
3 CH1: FD 0.5V/div. 0.5ms/div. / CH2: HOLD 5V/div. Normal mode: The defect part passes 800µm(B.D)
9 CH1: TD 0.1V/div. 0.5ms/div. / CH2: HOLD 5V/div. Normal mode: The defect part passes 800µm(B.D)
REFO
REFO
REFO
REFO
REFO
REFO
22
DEH-1300,12
23
1
2
3
4
DEH-1300,12
4. PCB CONNECTION DIAGRAM
4.1 TUNER AMP UNIT
A
A TUNER AMP UNIT
CORD ASSY
NOTE FOR PCB DIAGRAMS
1. The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic diagram. 2. Viewpoint of PCB diagrams
2 4 1 3 6 5 8 7 10 9 12 11 14 13 16 15
Connector
Capacitor
SIDE A
B
P.C.Board Chip Part
SIDE B
C
D
24
A
1
C
2
CN701
3 4
B
CN1801
5
6
7
8
DEH-1300,12
SIDE A
ANTENNA PRE OUT
A
3 1 2
2
1
B
C
FM/AM TUNER UNIT
D
FRONT
5 6 7
A
8
25
1
2
3
4
DEH-1300,12
A
A
TUNER AMP UNIT
4 5 6
3 2 1
B
C
1 2 3
6 5 4
D
26
A
1
2
3
4
5
6
7
8
DEH-1300,12
SIDE B
A
B
1 2 3
6 5 4
4 5 6
3 2 1
C
D
FRONT
5 6 7
A
8
27
B
D A C
28
DEH-1300,12
4.2 KEYBOARD UNIT
1 2 3 4 5 6 CLK
BAND
VOL-
LOUD
VOL-
SOURCE SOURCE
AUDIO
B
BSM EJECT
1
1
B
KEYBOARD UNIT
2
2
EQ
VOL+
VOL+
3
3
SIDE A
4
4
1
2
3
4
DEH-1300,12
SIDE B
A
B
CN601
A
C
KEYBOARD UNIT
D
B
1
2
3
B
4
29
B
D A C
30
DEH-1300,12
C
PICKUP UNIT(SERVICE)(P8) M1 CARRIAGE MOTOR M2 LOADING MOTOR
HOME
CONTROL UNIT
4.3 CD MECHANISM MODULE
C D
M3 SPINDLE MOTOR
1
1
2
2
D
3
3
D
PHOTO UNIT(S8)
A
CN605
4
4
SIDE A
3 2 1
C CN802
1
2
3
4
DEH-1300,12
SIDE B
A
CLAMP
B
CONTROL UNIT
C
C
D
1
2
3
C
4
31
DEH-1300,12
5. ELECTRICAL PARTS LIST
NOTES: - Parts whose parts numbers are omitted are subject to being not supplied. - The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS.....
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------Part No. ------------------------=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 335 342 343 344 345 346 351 352 353 354 360 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 427 428 460 461 464 465 468 469 610 611 619 620 622 623 624 625 626 627 628 629 630 631 649 650 651 655 656 657 658 Part No. ------------------------RS1/16S221J RS1/16S681J RS1/16S681J RS1/16S223J RS1/16S223J RS1/16S0R0J RS1/16S102J RS1/16S103J RS1/16S103J RS1/16S331J RD1/4PU153J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S103J RS1/16S681J RD1/4PU473J RD1/4PU472J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S681J RS1/16S681J RS1/16S393J RS1/16S222J RS1/16S222J RS1/16S272J RS1/16S272J RS1/16S162J RS1/16S162J RS1/16S0R0J RS1/16S0R0J RD1/4PU822J RS1/16S473J RS1/16S0R0J RS1/16S223J RD1/4PU222J RD1/4PU222J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S473J RD1/4PU222J RS1/16S473J RS1/16S822J RD1/4PU102J RS1/16S222J RD1/4PU222J RD1/4PU222J RS1/16S103J RS1/16S103J RD1/4PU102J RD1/4PU102J
A
IC IC IC IC IC Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q D D D D D D D D D D L L L L L L L L X AR
Unit Number : CWM7296 Unit Name : Tuner Amp Unit
301 302 601 602 970 346 350 351 353 411 650 901 902 903 904 905 906 920 981 982 901 902 903 904 905 906 907 941 942 981 310 401 402 403 610 611 650 901 610 946 IC IC IC IC IC Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Ferri-Inductor Ferri-Inductor Ferri-Inductor Inductor Ferri-Inductor Ferri-Inductor Ferri-Inductor Choke Coil 600µH Crystal Resonator 4.194304MHz Arrester FM/AM Tuner Unit PML003AM TDA7386 PE5196A S-80834ANY TPD1018F RN1610 DTA124EK DTC114EK DTA124EK 2SC2412K 2SA1037K 2SC2412K 2SC2412K 2SD1859 2SD2396 2SB1243 DTC114EK RN46A1 2SD2396 RN46A1 HZS7L(C2) S5688G S5688G HZS7L(A1) S5688G HZS6L(B2) HZS9L(B3) S5688G S5688G HZS9L(B1) LAU1R0M LAU4R7K LAU2R2K LAU100K LAU101K LAU2R2K LAU2R2K CTH1221 CSS1023 DSP-201M-S00B CWE1563
MISCELLANEOUS
RESISTORS
R R R R R 310 311 332 333 334 RD1/4PU222J RD1/4PU222J RS1/16S221J RS1/16S221J RS1/16S221J
32
DEH-1300,12
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R R R R R R R R R R R R R R R R R R R R 659 660 681 682 683 684 901 902 903 904 905 906 907 908 909 910 911 912 913 914 916 918 944 971 981 982 983 984
Part No. ------------------------RD1/4PU0R0J RS1/16S1R0J RD1/4PU681J RS1/16S102J RS1/16S102J RS1/16S102J RS1/16S104J RD1/4PU104J RD1/4PU103J RS1/16S473J RD1/4PU102J RS1/16S473J RS1/16S473J RS1/16S472J RD1/4PU103J RS1/16S0R0J RS1/16S122J RD1/4PU103J RS1/16S101J RD1/4PU152J RS1/16S221J RS1/16S1R0J RD1/4PU152J RS1/16S103J RS1/16S472J RS1/16S222J RD1/4PU221J RD1/4PU221J
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 412 413 414 415 416 417 419 420 462 463 490 499 612 613 614 628 629 630 631 650 901 902 903 904 905 906 907 941 971 972 981 982 983
Part No. ------------------------CKSRYB223K25 CKSRYB102K50 CEJA220M10 CKSRYB473K16 CEAL101M10 CKSRYB472K50 CCSRCH101J50 CCSRCH101J50 CKSRYB183K25 CKSRYB183K25 CKSQYB103K50 CKSRYB103K50 CEJA4R7M35 CKSRYB473K16 CCSRCH101J50 CCSRCH150J50 CCSRCH150J50 CKSRYB473K16 CEAL2R2M50 CKSRYB104K16 CEJA101M10 CKSRYB473K16 CCH1331 CKSRYB473K16 CCH1326 CKSRYB103K50 CEJA101M16 CKSRYB473K16 CKSRYB103K50 CKSRYB473K16 CEJA101M10 CKSRYB102K50 CKSRYB473K16
470µF/16V 330µF/16V
CAPACITORS
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 310 311 313 314 315 316 330 331 332 333 334 336 337 340 341 346 347 348 349 350 361 362 363 364 365 366 367 368 369 370 371 372 390 391 411 CKSRYB105K6R3 CKSRYB104K16 CKSRYB105K6R3 CKSRYB104K16 CKSRYB102K50 CKSRYB102K50 CEJA470M10 CEJA100M16 CKSRYB104K16 CEJA4R7M35 CEJA4R7M35 CKSRYB153K25 CKSRYB153K25 CEAL2R2M50 CEJA2R2M50 CCSRCH100D50 CCSRCH100D50 CCSRCH100D50 CCSRCH100D50 CEJA330M10 CEJA2R2M50 CKSQYB225K10 CEJA100M16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB474K16 CKSQYB225K10 CKSRYB104K16 CCH1368 CKSRYB223K25
B
IC D D D D D D D D D D X IL IL
Unit Number : CWM7310(DEH-1300/X1M/UC) Unit Name : Keyboard Unit
IC LED LED LED LED LED LED LED LED LED LED Ceramic Resonator 4.97MHz Lamp 14V 40mA Lamp 14V 40mA LCD PD6340A SML210PT SML210PT SML210PT SML210PT SML210PT SML210PT SML210PT SML210PT NSSW440-9159 NSSW440-9159 CSS1422 CEL1651 CEL1651 CAW1633
MISCELLANEOUS
1801 1701 1702 1703 1704 1705 1706 1707 1708 1811 1812 1801 1801 1802
RESISTORS
R R R R R R R R R R 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 RS1/16S151J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S151J RS1/16S151J RS1/16S151J RS1/16S181J RS1/16S151J
3300µF/16V
33
DEH-1300,12
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------R R R R R R R R R 1711 1712 1713 1801 1802 1803 1804 1805 1806
Part No. ------------------------RS1/16S181J RS1/16S151J RS1/16S131J RS1/16S222J RS1/16S222J RS1/16S471J RS1/16S471J RS1/16S471J RS1/16S471J
=====Circuit Symbol and No.===Part Name --- -----------------------------------------------
Part No. -------------------------
C
IC IC IC Q D D X S S
Unit Number : CWX2411 Unit Name : Control Unit
MISCELLANEOUS
201 301 701 101 801 802 201 801 802 IC IC IC Transistor LED LED Ceramic Oscillator 16.934MHz Spring Switch(HOME) Spring Switch(CLAMP) UPD63711GC BA5985FM BA05SFP 2SB1132 CL203IRXTU CL203IRXTU CSS1456 CSN1051 CSN1052
CAPACITORS
C C C 1801 1811 1812 CKSRYB103K50 CKSQYF104Z25 CKSQYF104Z25
B
IC D D D D D D D D D D X IL IL
Unit Number : CWM7309(DEH-12/X1M/UC) Unit Name : Keyboard Unit
IC LED LED LED LED LED LED LED LED LED LED Ceramic Resonator 4.97MHz Lamp 14V 40mA Lamp 14V 40mA LCD PD6340A SML210DT SML210DT SML210DT SML210DT SML210DT SML210DT SML210DT SML210DT NSSW440-9159 NSSW440-9159 CSS1422 CEL1638 CEL1638 CAW1633
RESISTORS
R R R R R R R R R R R R R R R R R R R R R R 101 102 103 201 202 203 204 205 206 207 302 303 501 502 601 602 605 606 801 803 902 906 RS1/8S120J RS1/8S100J RS1/16S222J RS1/16S104J RS1/16S103J RS1/16S393J RS1/16S103J RS1/16S103J RS1/16S182J RS1/16S123J RS1/16S153J RS1/16S103J RS1/16S102J RA4C681J RS1/16S102J RS1/16S102J RS1/16S0R0J RS1/16S0R0J RS1/8S751J RS1/8S751J RS1/16S0R0J RS1/16S0R0J
MISCELLANEOUS
1801 1701 1702 1703 1704 1705 1706 1707 1708 1811 1812 1801 1801 1802
RESISTORS
R R R R R R R R R R R R R R R R R R R 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1801 1802 1803 1804 1805 1806 RS1/16S151J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S151J RS1/16S151J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S181J RS1/16S131J RS1/16S222J RS1/16S222J RS1/16S471J RS1/16S471J RS1/16S471J RS1/16S471J
CAPACITORS
C C C C C C C C C C C C C C C C C C C C C C C C C 101 102 103 104 105 106 107 201 202 203 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 CKSRYB102K50 CKSRYB104K16 CEV101M6R3 CEV470M6R3 CKSQYB334K16 CKSQYB334K16 CKSQYB334K16 CKSRYB104K16 CKSRYB471K50 CKSRYB104K16 CEV101M6R3 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB332K50 CKSRYB104K16 CKSRYB104K16 CKSRYB392K50 CKSRYB104K16 CKSRYB104K16 CCSRCJ3R0C50 CCSRCH270J50 CKSRYB104K16 CCSRCH181J50
CAPACITORS
C C C 1801 1811 1812 CKSRYB103K50 CKSQYF104Z25 CKSQYF104Z25
34
DEH-1300,12
=====Circuit Symbol and No.===Part Name --- ----------------------------------------------C C C C C C C C C C 220 221 222 223 224 301 603 604 702 703
Part No. ------------------------CCSRCH510J50 CKSRYB682K25 CEV220M6R3 CKSRYB103K25 CKSRYB224K10 CEV101M10 CCSQSL152J50 CCSQSL152J50 CCH1349 CKSQYB334K16
10µF/10V
D
Q Q
Unit Number : Unit Name : Photo Unit(S8)
1 2 Photo-transistor Photo-transistor CPT230SX-TU CPT230SX-TU
Miscellaneous Parts List
M M M 1 2 3 Pickup Unit(Service)(P8) Motor Unit(CARRIAGE) Motor Unit(LOADING) Motor Unit(SPINDLE) Fuse(10A) CXX1285 CXB2190 CXB2195 CXB2562 CEK1136
35
DEH-1300,12
6. ADJUSTMENT
6.1 CD ADJUSTMENT
1) Precautions · This unit uses a single power supply (+5V) for the regulator. The signal reference potential, therefore, is connected to REFO(approx. 2.5V) instead of GND. If REFO and GND are connected to each other by mistake during adjustments, not only will it be impossible to measure the potential correctly, but the servo will malfunction and a severe shock will be applied to the pick-up. To avoid this, take special note of the following. Do not connect the negative probe of the measuring equipment to REFO and GND together. It is especially important not to connect the channel 1 negative probe of the oscilloscope to REFO with the channel 2 negative probe connected to GND. Since the frame of the measuring instrument is usually at the same potential as the negative probe, change the frame of the measuring instrument to floating status. If by accident REFO comes in contact with GND, immediately switch the regulator or power OFF. · Always make sure the regulator is OFF when connecting and disconnecting the various filters and wiring required for measurements. · Before proceeding to further adjustments and measurements after switching regulator ON, let the player run for about one minute to allow the circuits to stabilize. · Since the protective systems in the unit's software are rendered inoperative in test mode, be very careful to avoid mechanical and /or electrical shocks to the system when making adjustment. · Disc detection during loading and eject operations is performed by means of a photo transistor in this unit.Consequently, if the inside of the unit is exposed to a strong light source when the outer casing is removed for repairs or adjustment, the following malfunctions may occur. *During PLAY, even if the eject button is pressed,the disc will not be ejected and the unit will remain in the PLAY mode. *The unit will not load a disc. When the unit malfunctions this way, either re-position the light source, move the unit or cover the photo transistor. 2) Test Mode This mode is used for adjusting the CD mechanism module of the device. · Test mode starting procedure Reset while pressing the 4 and 6 keys together. · Test mode cancellation Switch ACC, back-up OFF. · After pressing the EJECT key, do not press any other key until the disk is completely ejected. · If the ] or [ key is pressed while focus search is in progress, immediately turn the power off (otherwise the actuator may be damaged due to adhesion of the lenses). · Jump operation of TRs other than 100TR continues after releasing the key. CRG move and 100TR jump operations are brought into the "Tracking close" status when the key is released. · Powering Off/On resets the jump mode to "1TR", and the automatic adjustment value to the initial value.
36
DEH-1300,12
- Flow Chart
4
Test Mode In Reset
6
Select CD
SOURCE
New test mode
BAND
Power ON (Adjustment for T.Offset)
TRK MIN SEC
3
6
Display
00 00 00
Power ON (Not adjustment for T.Offset)
TRK MIN SEC
Display Power OFF
99 99 99
BAND
Focus Close/ S Curve Check
TRK MIN SEC
3 *1
Focus Mode Select
6 *2
1
]
[
2 *3
SEC TRK MIN SEC TRK
CRG+
MIN SEC
CRGTRK MIN SEC
Auto Adjustment Display Select
TRK
MIN
Display
91 91 91
Display
0x 0x 0x
00 00 00
or
TRK MIN SEC
00 00 00
or
TRK MIN SEC
00 00 00
or
TRK MIN SEC
99 99 99
Power OFF
99 99 99
99 99 99
BAND
T.Close and F,T AGC and RF AGC and Fit Servo
1
6
3
]
[
2
T. Close and Fit Servo
RF AGC Coefficient Display/ Rough Servo and RF AGC
TRK
CRG+
MIN SEC
CRGTRK MIN SEC
T.Balance Adjustment
Display
8x 8x 8x
or
TRK MIN SEC
8x 8x 8x
or
TRK MIN SEC
9x 9x 9x
Power OFF
9x 9x 9x
Tracking Open
BAND
1 *4
F, T, RF AGC/ F.Bias Display Select
3
6 *5
]
[
2
*6 CRG-/TR Jump- *6
CRG+/TR Jump+
F, T AGC and RF AGC
CRG/TR Jump NO. Select
*7
TRK MIN SEC
Power OFF
Display
8x 8x 8x
or
TRK MIN SEC
BAND
Tracking Open
TRK MIN
2
9x 9x 9x
SEC
Display
8x 8x 8x
or
TRK MIN SEC
9x 9x 9x
*1 *2 "00", "99"Focus Close / "01"S.Curve Focus Close 00(99) S.Curve 01 LD Off 02 *6 *7 1TR/4TR/10TR/32TR/100TR CRG Move,100TR Jump
*3 *4
F.Cancel
T.Offset
The original display
TRK, MIN, SEC
F.AGC Gain
T.AGC Gain
F.Bias
*5
1TR 91(81)
4TR 92(82)
10TR 93(83)
32TR 94(84)
100TR 95(85)
CRG Move 96(86)
37
DEH-1300,12
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT
· Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below.
· Purpose : To check that the grating is within an acceptable range when the PU unit is changed. · Symptoms of Mal-adjustment : If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching. · Method : · Measuring Equipment · Measuring Points · Disc · Mode
· Oscilloscope, Two L.P.F. · E, F, REFOUT · ABEX TCD-784 · TEST MODE
CONTROL UNIT
E F
E REFO
L.P.F. Xch 100k 390pF Ych
Oscilloscope
F
100k 390pF L.P.F.
REFO
REFO
· Checking Procedure 1. In test mode, load the disc and switch the 5V regulator on. 2. Using the ] and [ buttons, move the PU unit to the innermost track. 3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on the fourth press. 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75° . Refer to the photographs supplied to determine the phase angle. 5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the mechanism should be judged to be at fault. · Note Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. · Hint Reloading the disc changes the clamp position and may decrease the "wobble".
38
DEH-1300,12
Grating waveform
Ech Xch 20mV/div, AC Fch Ych 20mV/div, AC 30°
0°
45°
60°
75°
90°
39
DEH-1300,12
7. GENERAL INFORMATION
7.1 DIAGNOSIS 7.1.1 TEST MODE
- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing. (1) Basic Indication Method 1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains in blank as before. 2) Head unit display examples Depending on display capability of LCD used, display will vary as shown below. xx contains the error number. 8-digit display ERRORxx 6-digit display ERRxx OR Errxx 4-digit display Exx
(2) Error Code List Code Class Displayed error code Description of the code and potential cause(s) 10 Electricity Carriage Home NG CRG can't be moved to inner diameter. CRG can't be moved from inner diameter. Failure on home switch or CRG move mechanism. 11 12 Electricity Electricity Focus Servo NG Spindle Lock NG Subcode NG Focusing not available. Stains on rear side of disc or excessive vibrations on REWRITABLE. Spindle not locked. Sub-code is strange (not readable). Failure on spindle, stains or damages on disc, or excessive vibrations. A disc not containing CD-R data is found. Turned over disc are found, though rarely. Failure on home switch or CRG move mechanism. An appropriate RF AMP gain can't be determined. CD signal error. APC protection doesn't work. Focus can be easily lost. Damages or stains on disc, or excessive vibrations. Failed to reach target address. CRG tracking error or damages on disc. Power (VD) is ground faulted. Failure on SW transistor or power supply (failure on connector).
RF AMP NG 17 30 A0 Electricity Electricity System Setup NG Search Time Out Power Supply NG
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. A newly designed head unit must conform to the example given above. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, 3x: Search relevant errors, Ax: Other errors.
40
DEH-1300,12
- New Test Mode
S-CD plays the same way as before. If an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its cause and time occurred (in absolute time) are displayed. During setup, operational status of the control software (internal RAM: CPOINT) is displayed. These displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis. (1) Shifting to the New Test Mode 1 Turn on the current test mode by starting the reset from the key. 2 Select S-CD for the source through the specified procedure including use of the [SOURCE] key, and inserting the disc. Then, press the [Jump Mode Selector] key while maintaining the regulator turned off. 3 After the above operations, the new test mode remains on irrespective of whether the S-CD is turned on or off. You can reset the new test mode by turning on the reset start. * With some products, the new test mode can be reset through the same operations as that employed for shifting to the STBY mode (while maintaining the Acc turned off). (2) Key Correspondence Key Test mode (Example) Power Off Power On BAND To power on To power off (offset adjustment performed) ] [ 1 2 3 FWD-Kick REV-Kick T.Close (AGC performed) /parameter display switching T.BAL adjustment /T.Open F.Close/RF AGC/AGC
In-play FF/TR+ REV/TRScan Mode
New test mode Error Production Time/Err.No. switching
To power on (offset adjustment not performed) 6 Mode switching Auto/Manu /T.Close (no AGC)/Jump switching Note: Eject and CD on/off is performed in the same procedure as that for the normal mode. (3) Cause of Error and Error Code Code Class Contents 40 Electricity Off focus detected. 41 42 43 Electricity Electricity Electricity Spindle unlocked. Sub-code unreadable. Sound skipping detected.
Description and cause FOK goes low. Damages/stains on disc, vibrations or failure on servo. FOK = Low continued for 50 msec. Damages/stains on disc, vibrations or failure on servo. Sub-code was unreadable for 50 msec. Damages/stains on disc, vibrations or failure on servo. Last address memory function was activated. Damages/stains on disc, vibrations or failure on servo.
Note: Mechanical errors during aging are not displayed. The error codes should be indicated in the same way as in the normal mode.
41
DEH-1300,12
(4) Display of Operational Status (CPOINT) during Setup Status No. Contents 01 Carriage move to home position started. 02 Carriage is moving toward inner diameter. 03 05 11 12 13 14 15 16 17 18 24 25 26 27 28 29 30 31 32 33 34 35 36 Carriage is moving toward outer diameter. Carriage outer diameter feed (1 second) in progress. Setup started. Spindle rotation and focus search started. Waiting for focus close (XSI=Low). Waiting for focus close (FOK=High). (After AGC) Waiting for focus close (FOK=High). (Before AGC) Rough AGC in progress. Setup (1/2) before T balance adjustment is started. Setup (2/2) before T balance adjustment is started. T balance adjustment (1/2). T balance adjustment (2/2). Standing by after spindle rough servo is over. Setup before RF AGC (first) is started. RF AGC (first) in progress. Setup before RF AGC (second) is started. RF AGC (second) in progress. Tracking close in progress. Standing by after tracking is closed. Focus AGC started. Focus AGC in progress. Tracking AGC started. Tracking AGC in progress. Spindle processes applicable servo. Check of MIRR and LOCK pin. RF AGC in progress. CRG close in progress. Check of sub-code.
Protective action None Specified 10 seconds has been passed or failure on home switch. Specified 10 seconds has been passed or failure on home switch. None None None Specified focus search time has been passed. Specified focus search time has been passed. Specified focus search time has been passed. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Off focus. Spindle not locked. Sub-code unreadable.
(5) Display Examples 1) During Setup (When status no. = 11) TRK No. MIN. SEC. 11 11' 11" 2) During Operation (TOC read, TRK search, Play, FF and REV) The same as in the normal mode. 3) When a Protection Error Occurred Switch to the following displays (A) and (B) using the [BAND] switch: (A) Error occurrence timing display in absolute time. An example: Error occurred in 12th tune at 34'56" in absolute time. TRK No. 12 MIN. 34' SEC. 56"
(B) Error No. display An example: Error #40 (Off focus is detected) ERROR-40
42
DEH-1300,12
7.1.2 DISASSEMBLY
- Removing the Case Unit (not shown)
1. Remove the Case Unit.
- Removing the CD Mechanism Module (Fig.1)
Remove the four screws. Disconnect the connector and then remove the CD Mechanism Module (not shown).
- Removing the Grille Assy (not shown)
1. Disconnect the two stoppers and then remove the Grille Assy.
CD Mechanism Module
Fig.1
Cover
- Removing the Tuner Amp Unit
Remove the three screws and then remove the Cover. (Fig.2) Remove the two screws. (Fig.2)
Remove the screw. (Fig.3)
Fig.2
Straight the tabs at fore locations indicated and then remove the Tuner Amp Unit. (Fig.3)
Fig.3 Tuner Amp Unit
43
DEH-1300,12
- Removing the Upper Frame
1. Remove six Springs A, two Springs B and four Screws. 2. Remove two Tabs situated on rear side of the Upper Frame, remove two Arms on the front side, then remove two Tabs on the front side.
A A
A Upper Frame
B
A
Arm
A
Arm B A
- Removing the Carriage Mechanism
1. Disengage the Carriage Mechanism from the two dampers situated in the front side by driving it up, then disengage and remove the mechanism from the one damper by driving it up aslant into front side direction. Note : When assembling the Carriage Mechanism, coat the dampers with alcohol prior to the assembly.
Carriage Mechanism Section
- Removing the Clamp Arm Assy
1. Remove a Spring A, a B and a Spring C. 2. Drive the Clamp Arm Assy up into rear side direction, then disengage the arm from its current position Finally, drive the assembly approximately 45 degrees upward, then slide the assembly toward right side to remove it.
A
Clamp Arm Assy Section B
C
44
DEH-1300,12
- Removing the Guide Arm Assy
1. Remove a connector, a spring A and B 2. Drive the Guide Arm Assy up aslant into rear side direction, then remove it from a Pin. Finally, drive the assembly approximately 45 degrees upward, then slide the assembly toward left side to remove it. Note : When assembling the guide arm assembly, route the cord inside the assembly. In this operation, care must be exercised so that cord may be caught by the gear.
Guide Arm Assy Section
A
B Pin
LO Arm Assy Section
- Removing the LO Arm Assy
1. Remove two Pins to dismount the LO Arm Assy.
- Removing the Control Unit and the Spindle Motor
1. Remove from the connector after mounting the short pin on the flexible PCB of the pickup unit. 2. Remove two Soldered joints, then remove two Screws A. 3. Remove two connectors and a Screw B. 4. Disengage the Control Unit from two Tabs, then dismount the unit by sliding it toward left. 5. Dismount the Spindle Motor.
Short Pin
Spindle Motor
B
Control Unit
A
A
45
DEH-1300,12
- Removing the Loading Motor and Carriage Motor
1. Remove the Spring and two Screws A. 2. Dismount the Loading Motor. 3. Remove the Belt, a Screw B, two Screws C, a Guide and a Screw Unit. 4. Dismount the Carriage Motor. Note : When assembling the Belt, use care so that it may not be contaminated by grease.
C Guide
B Screw Unit Carriage Motor
Belt
C
A
A Loading Motor
- Removing the Pickup Unit
1. Remove two Screws and a Shaft. 2. Dismount the Pickup Unit.
Pickup Unit
Shaft
46
DEH-1300,12
7.1.3 CONNECTOR FUNCTION DESCRIPTION
PRE OUT
ANTENNA
15 13 11 9 7 5 3 1 16 14 12 10 8 6 4 2
1. BACK UP 2. GND 3. NC 4. ACC 5. B.REM 6. NC 7. NC 8. NC 9. FL10. RL11. FL+ 12. RL+ 13. FR14. RR15. FR+ 16. RR+
47
DEH-1300,12
7.2 PARTS 7.2.1 IC
- Pin Functions(PE5196A) Pin No. Pin Name 1 MODEL1 2 NL1 3 NL2DT 4 AVSS 5 ST 6 SD 7 AREF1 8 KYDT 9 DPDT 10 SDBW 11 TUNPDI 12 TUNPDO 13 TUNPCK 14 TUNPCE 15 currq 16 XSI 17 XSO 18 XSCK 19 drst 20 ADPW 21 fm/AM 22 VDCONT 23 CONT 24 XAO 25 xrst 26 xstb 27 CLAMP 28 MIRR 29 FOK 30 LOCK 31 CDLOAD 32 TELIN 33 VSS 34 CDEJECT 35 CD5VON 3639 NC 40 RECIEVE 41 swvdd 42 SYSPW 43 ILMPW 44 mute 45 PEE 46 LOCH 47 RDS57K 48 TUNPCE2 49 PCL 50 VCK 51 VDT 52 ANTPW 53 VST 54 DALMON 55,56 NC 57 LOCL 58 rdslk I/O I I I I I I O I I O O O O I O O O O O O O O O O I I I I O I O O O O O O O O O I O O O O O O O O I Format Function and Operation Model select input Noise level input Noise level input 2 AVSS Stereo input SD signal input AVREF1 Key data input Key data output SDBW input PLL IC data input PLL IC data output PLL IC clock output PLL IC chip enable output Tuner voltage FIX output CD LSI serial data input(TSI) CD LSI serial data output(TSO) CD LSI serial clock output(TSCK) RDS decoder reset output A/D converter power output Tuner power supply control output VD power supply control output Servo driver power control output CD LSI command / data control output CD LSI reset control output CD LSI strobe output Disc clamp sense input Mirror detection input Focus OK signal input Spindle lock detector input LOAD motor loading control output Cellular mute input VSS LOAD motor eject control output CD +5V power supply control output Not used RDS decoder receiving output Grille microcomputer power supply control output System power supply control output Illumination power output Mute output Beep tone output LOCH output 57kHzBP-OUT sense input EEPROM chip enable output Test mode clock adjustment output Clock output for electronic volume Data output for electronic volume Antenna power output Strobe pulse output for electronic volume Stand-by output Not used LOCL output RDSLK input
C
C C C C C C C C C C C C C C C
C C C C C C C C C C C C
48
DEH-1300,12
Pin No. 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
Pin Name RDT reset LDET RCK asens bsens dsens TMUTE NC VDD X2 X1 IC(VPP) NC TESTIN AVDD AVREF0 SL TEMP VDSENS DINC EJTD
I/O I I I I I I O
Format
C
I
I I I I I
Function and Operation RDS data input Reset PLL lock detection input RDS clock input ACC power sense input Back up power sense input Grille detach sense input Tuner mute output Not used VDD Crystal oscillator connection pin Crystal oscillator connection pin IC(VPP) Not used Test program mode input AVDD AVREF0 Signal level input Temperature detection input VD power supply sense input Disc detection input Disc eject position detect input IC's marked by* are MOS type. Be careful in handing them because they are very liable to be damaged by electrostatic induction.
Output Format C *PE5196A 80 1
Meaning C MOS output
61 60
S-80834ANY
20 21 40
41
1
OUT
2
VDD
3
VSS
49
DEH-1300,12
- Pin Functions (PD6340A)
Pin No. 1-5 6-9 10 11-14 15,16 17 18 19 20 21 22 23 24 25,26 27 28 29-32 33-55 56 57-64 Pin Name SEG4-0 COM3-0 VLCD KST3-0 KDT0,1 REM DPDT NC KYDT MODA X0 X1 VSS KDT2,3 NC KST4 NC SEG35-13 VDD SEG12-5 I/O O O O I I I O Function and Operation LCD segment output LCD common output LCD drive power supply Key strobe output Key data input (analogue input) Remote control reception Display data input Not used Key data output GND Crystal oscillator connection pin Crystal oscillator connection pin GND Key data input Not used Key strobe output Not used LCD segment output Power supply LCD segment output
I O O O
*PD6340A
33
32
48 49 64 1
17 16
50
DEH-1300,12
- Pin Functions (UPD63711GC)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Pin Name D.GND RFOK rst A0 stb sck SO SI xtalen D.VDD DA.VDD R_OUT DA.GND REGC DA.GND L_OUT DA.VDD R+ RLL+ X.VDD XTAL xtal X.GND D.VDD EMPH FLAG DIN DOUT SCKIN SCKO LRCKIN LRCK HOLD TX D.GND C16M LIMIT D.VDD LOCK RFCK MIRR PLCK D.GND C1D1 C1D2 C2D1 C2D2 C2D3 D.VDD PACK TSO TSI tsck TSTB D.GND I/O O I I I I O I I Function and Operation Logic circuit GND RFOK signal output Reset signal input Command/parameter identification signal input Data strobe signal input Clock signal input for serial data input/output Serial data and status signal output Serial data input Crystal oscillation control pin Positive power supply terminal to logic circuit Positive power supply terminal to D/A converter Right channel audio output signal D/A converter GND The outside putting capacitor connection pin for SCF regulator D/A converter GND Left channel audio output signal Positive power supply terminal to D/A converter Right channel audio data output Right channel audio data output Left channel audio data output Left channel audio data output Positive power supply terminal to crystal oscillation circuit Crystal oscillator connect pin Crystal oscillator connect pin Crystal oscillation circuit GND Positive power supply terminal to logic circuit Output pin for the pre-emphasis data in the sub-Q code Flag output pin to indicate that audio data currently being output consists of noncorrectable data Serial data input to internal DAC Serial audio data output Serial clock input to internal DAC Audio data that is output from DOUT changes at rising edge of this clock LRCK signal input to internal DAC Signals to distinguish the right and left channels of the audio data output from DOUT Defect detection output Digital audio interface data output Logic circuit GND Oscillator clock buffering output Status of the pin is output at Bit 5 of the status output Positive power supply terminal to logic circuit EFM synchronous detection signal Frame synchronous signal of XTAL-system MIRR output Monitor pin of bit clock Logic circuit GND Output pin for indicating the C1 error correction results Output pin for indicating the C1 error correction results Output pin for indicating the C2 error correction results Output pin for indicating the C2 error correction results Output pin for indicating the C2 error correction results Positive power supply terminal to logic circuit CD-TEXT PACK synchronous signal CD-TEXT data serial output CD-TEXT control parameter serial input CD-TEXT serial clock input CD-TEXT parameter strobe signal input Logic circuit GND
O I O O O O O I O
O O I O I O I O O O O I O O O O O O O O O O O I I I
51
DEH-1300,12
Pin No. 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 *UPD63711GC
25 20 26 21
Pin Name TEST0 TEST1 ATEST A.GND FD TD SD MD DAC0 DAC1 DAC2 DAC3 A.VDD EFM ASY C3T RFI AGCO AGCI RFO EQ2 EQ1 RFA.GND A C B D F E A.VDD REFOUT FEFEO TETEO TE2 TEC A.GND PD LD PN A.VDD
I/O I I O O O O O O O O O O I I O I O
I I I I I I I O I O I O O I I O I
Function and Operation Test pin Test pin Test pin Analog circuit GND Focus drive output Tracking drive output Sled drive output Spindle drive output DAC output for adjustment DAC output for adjustment DAC output for adjustment DAC output for adjustment Positive power supply terminal to analog circuit EFM signal output EFM comparator reference voltage input 3T detection capacitor additional pin RF signal input for EFM data regulation RF signal output of after gain adjustment RF-AGC amplifier input RF summing amplifier output RF amplifier equalizer parts additional pin RF amplifier equalizer parts additional pin RF summing amplifier inverted input Analog circuit GND Photo detector A input Photo detector C input Photo detector B input Photo detector D input Photo detector F input Photo detector E input Positive power supply terminal to analog circuit Reference electric potential output Focus error amplifier inverted input Focus error amplifier output Tracking error amplifier inverted input Tracking error amplifier output Tracking error output of after amplification Tracking comparator input Analog circuit GND PD detection signal input for LD output monitor LD control current output APC circuit control polarity set pin Positive power supply terminal to analog circuit
1 1 100 80 76 61 75 60
50 40 51 41
52
DEH-1300,12
FM/AM TUNER UNIT
AMRF
28 AMANT
FM/AM 1ST IF 10.7MHz T51 Q51 CF51 CF52 CF53
MPXREF 41kHz AMDET IC 2 FM MPX
L ch 6 R ch 5
ATT
ANT ADJ
FMANT
IC1 MIXER, IF AMP, DET.
COMP LDET
21 18
27 RFGND 26
ATT FMRF CF202 IMG ADJ AM 2ND IF X901 450kHz 10.25MHz
WC NC NC
IC 3 EEPROM
FMLOCL SDBW DGND FMSD DI/DO NL1 NL2 4 CE2 CE1 STIND 1
NC
CK
LOCH 23 25
LOCL
7 17 20 22 10 19 14
24
9
11 12 15 16
8
SL 13
RF ADJ
CREQ
VDD VCC
2
3
No. Symbol I/O Explain 1 STIND O stereo indicator 2 FMSD O FM station detector
"Low" when the FM stereo signals are received. To be pulled up to the "VDD" at 47k. "High" when signals are received. To be pulled up to the "VDD" at 47k Meanwhile, 10k should be used when taking diver FIX trigger from here and "High: 0.9VDD or more" and "Low: 250mV or less". (Should satisfy the diver IC specifications) 3 NL1 O noise level-1 "High" when noise is received. Output for the RDS. GND at 47k //1,800pF. 4 NL2 O noise level-2 "High" when noise is received. Output for the RDS. GND at 36k //330pF. 5 Rch O R channel FM stereo "R-ch" signal output or AM audio output. output Add the specified di-emphasis constant. 6 Lch O L channel FM stereo "L-ch" signal output or AM audio output. output Add the specified di-emphasis constant. 7 WC write control EEPROM write control. Writing permissible at "Low". Normally open. 8 SDBW O SD bandwidth SD bandwidth signal output. For detection of detuning data for the RDS. 9 NC Not used 10 VDD power Power supply pin for the digital section. supply D.C. 5V +/- 0.25V. Be careful about overlapping noise in the logic section. 11 DGND digital ground Grounding for the digital section. 12 CE2 I chip enable-2 EEPROM chip enable. Active a "Low" To be pulled up to the "VDD" at 47k 13 SL I/O signal level Received FM/AM signal level (strength) output. Connect the specified load resistor and capacitor (10k + 39k //4,700pF) 14 DI/DO I/O data input/ Data input/Data output data output To be pulled up to the "VDD" at 47k 15 CK I clock Clock input To be pulled up to the "VDD" at 47k 16 CE1 I chip enable-1 AF·RF chip enable. Active at "High" To be grounded at 47k 17 NC Not used 18 LDET O lock detector Active at "Low". To be pulled up to the "VDD" at 47k 19 CREQ I current request Active at "Low". To be grounded at 47k 20 NC Not used 21 COMP O composite signal FM composite signal output. r out < 100 22 VCC power supply Analog section power supply pin.D.C.8.4V +/- 0.3V 23 LOCH I local high FM local high pin. When seeking local high, apply 5V together with "LOCL". 24 FMLOCL I FM local low FM local low pin. When seeking local low, apply 5V to the base of the NPN transistor with which the specified resistor is being connected to the emitter. Keep it open in case of ordinary marketed models. 25 LOCL I local low FM/AM local low pin. When seeking local low, apply 5V to the base of the NPN transistor. Since this pin is exclusive for AM when the FMLOCL is in use, do not drive it under FM. 26 RFGND RF ground Grounding for the antenna section. 27 FMANT I FM antenna input FM antenna input. 75. Serge absorber (DSP-201M-S00B) is necessary. 28 AMANT I AM antenna input AM antenna input. High impedance. Connect to the antenna through an L (LAU type) of 4.7µH.To cope with the power transmission line hums, insert a series circuit consisting of an L (a coil of about 100mH) + R (a resistor of 470 to 2.2k) between the GND.
53
COM3A COM2A COM1A COM2B COM0A COM2C COM3B COM2D COM1B COM0B
COM3A COM2A COM1A COM2B COM0A COM2C COM3B COM2D COM1B COM0B SEG39 SEG38 SEG37 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 NC NC SEG36
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
DEH-1300,12
54
- CAW1633
7.2.2 DISPLAY
COMMON
SEGMENT
DEH-1300,12
7.3 OPERATIONAL FLOW CHART
Power ON
VDD=5V 68pin
bsens 64pin BSENS=L asens 63pin ASENS=L dsens 65pin DSENS=L ADPWH 20pin
Starts communication with Grille microcomputer. 300ms SWVDDL 41pin Source keys operative
300ms In case of the above signal, the communication with Grille microcomputer may fail. If the time interval is not 300msec, the oscillator may be defective.
Source ON
SYSPWH 42pin
Completes power-on operation.(After that, proceed to each source operation.)
55
DEH-1300,12
8. OPERATIONS AND SPECIFICATIONS
8.1 OPERATIONS
Key Finder
Head Unit
+/ buttons
LOCAL/BSM button
EQ button
CD loading slot
EJECT button
AUDIO button BAND button
LOUD button Buttons 16 SOURCE button 5//2/3 buttons CLOCK button
56
Basic Operation
Basic Operation of Tuner
To Listen to Music
The following explains the initial operations required before you can listen to music.
Note:
· Loading a disc in this product.
Manual and Seek Tuning · You can select the tuning method by changing the length of time you press the 2/3 button.
Manual Tuning (step by step) Seek Tuning 0.5 seconds or less 0.5 seconds or more
1. Select the desired source (e.g. Tuner).
Each press changes the Source ...
Each press of the SOURCE button selects the desired source in the following order: Built-in CD player = Tuner
Note:
· If you continue pressing the button for longer than 0.5 seconds, you can skip broadcast stations. Seek Tuning starts as soon as you release the button. · Stereo indicator "" lights when a stereo station is selected.
Note:
· When no disc is set in this product, built-in CD player source will not change. · When this product's blue/white lead is connected to the car's Auto-antenna relay control terminal, the car's Auto-antenna extends when this product's source is switched ON. To retract the antenna, switch the source OFF.
Frequency Indicator Band Indicator Preset Number Indicator
2. Raise or lower the volume.
3. Turn the source OFF.
Preset Tuning · You can memorize broadcast stations in buttons 1 through 6 for easy, one-touch station recall.
Preset station recall Broadcast station preset memory 2 seconds or less 2 seconds or more
Band
FM1 = FM2 = FM3 = AM
Hold for 1 second
Note:
· Up to 18 FM stations (6 in FM1, FM2 and FM3) and 6 AM stations can be stored in memory. · You can also use the 5 or buttons to recall broadcast stations memorized in buttons 1 through 6.
DEH-1300,12
57
DEH-1300,12
58
Basic Operation
Basic Operation of Built-in CD Player
Eject
Note:
· The CD function can be turned ON/OFF with the disc remaining in this product. · A disc left partially inserted after ejection may incur damage or fall out.
CD Loading Slot
Note:
· The built-in CD player plays one standard 12 cm or 8 cm (single) CD at a time. Do not use an adapter when playing 8 cm CD. · Don't insert any materials except for CD into CD loading slot.
Track Number Indicator
Play Time Indicator
Track Search and Fast Forward/Reverse
· You can select between Track Search or Fast Forward/Reverse by pressing the 2/3 button for a different length of time.
0.5 seconds or less Continue pressing
Track Search
Fast Forward/Reverse
Note:
· If a disc cannot be inserted fully or playback fails, make sure the recorded side is down. Push the EJECT button and check the disc for damage before reinserting it. · If a disc is inserted with the recorded side up, it will be ejected automatically after a few moments. · If the built-in CD player cannot operate properly, an error message (such as "ERR-14") appears on the display. Refer to "Built-in CD Player's Error Message".
Connection Diagram
This product
Rear output Connecting cords with RCA pin plugs (sold separately).
Power amp (sold separately)
Antenna jack
Fuse
Yellow To terminal always supplied with power regardless of ignition switch position.
Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC).
System remote control
Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF. White + Front speaker Left + Rear speaker Green/black Violet/black White/black Green Gray/black Violet + Rear speaker Right Gray + Front speaker
Black (ground) To vehicle (metal) body.
With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.
Perform these connections when using a different amp (sold separately). Rear speaker
+
+ Rear speaker
DEH-1300,12
59
DEH-1300,12
8.2 SPECIFICATIONS
General
Power source .......... 14.4 V DC (10.8 15.1 V allowable) Grounding system ........................................ Negative type Max. current consumption ...................................... 10.0 A Dimensions (DIN) (chassis) ...... 178 (W) × 50 (H) × 159 (D) mm [7 (W) × 2 (H) × 6-1/4 (D) in] (nose) ............ 188 (W) × 58 (H) × 19 (D) mm [7-3/8 (W) × 2-1/4 (H) × 3/4 (D) in] (D) (chassis) ...... 178 (W) × 50 (H) × 164 (D) mm [7 (W) × 2 (H) × 6-1/2 (D) in] (nose) ............ 170 (W) × 46 (H) × 14 (D) mm [6-3/4 (W) × 1-3/4 (H) × 1/2 (D) in] Weight ........................................................ 1.4 kg (3.1 lbs) Electrode dark current .................................... 6mA or less
CD player
System .................................... Compact disc audio system Usable discs .................................................. Compact disc Signal format .................... Sampling frequency: 44.1 kHz Number of quantization bits: 16; linear Frequency characteristics .............. 5 20,000 Hz (±1 dB) Signal-to-noise ratio ...... 94 dB (1 kHz) (IHF-A network) Dynamic range ............................................ 92 dB (1 kHz) Number of channels ............................................ 2 (stereo)
FM tuner
Frequency range .................................... 87.9 107.9 MHz Usable sensitivity ...................................................... 9 dBf (0.8 µV/75 , mono, S/N: 30 dB) 50 dB quieting sensitivity .... 15 dBf (1.5 µV/75 , mono) Signal-to-noise ratio ...................... 70 dB (IHF-A network) Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo) Frequency response ...................... 30 15,000 Hz (±3 dB) Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz) Selectivity .................................................................. 70 dB Three-signal intermodulation (desired signal level) ........................................ 30 dBf (two undesired signal level: 100 dBf)
Amplifier
Continuous power output is 20 W per channel min. into 4 ohms, both channels driven 50 to 15,000 Hz with no more than 5% THD. Maximum power output ......................................45 W × 4 Load impedance .......................... 4 (4 8 allowable) Preout maximum output level/output impedance ............................ 2.2 V/1 k Equalizer (3-Band Equalizer) (Low) .................................................. Level: ±12 dB (Mid) .................................................... Level: ±12 dB (High) .................................................. Level: ±12 dB Loudness contour (Low) .................. +3.5 dB (100 Hz), +3 dB (10 kHz) (Mid) ................ +10 dB (100 Hz), +6.5 dB (10 kHz) (High) ................ +11 dB (100 Hz), +11 dB (10 kHz) (volume: 30 dB)
AM tuner
Frequency range ...................... 530 1,710 kHz (10 kHz) Usable sensitivity .............................. 18 µV (S/N: 20 dB) Selectivity ................................................ 50 dB (±10 kHz)
Note:
· Specifications and the design are subject to possible modification without notice due to improvements.