Text preview for : UV-A_solarium_©_.pdf part of Philips HB 544/A Service Manual UV-A Solarium 1160W (00/08) - pag. 2
Back to : UV-A_solarium_©_.pdf | Home
UV-A Solarium
Service Service Service
Domestic Appliances and Personal Care
HB 544/A
Service Manual 4822 729 21763 is herewith cancelled.
Service Manual
SAP coding 8843 544 99999
PRODUCT INFORMATION UVA lamps Input power Starter Ballast Timer Radiation area Radiation distance Height adjustment Protecting goggles Output UVX36 meter : : : : : : : : : : : : : 10 x TL100W/Cleo 4 x TL 15W/Cleo approx. 1160W 10 x S12 4 x S2 10 x 100W/230V 2 x 30W 60 mins Eaton 170 x 56 cm 20 cm between 66-96 cm HB071 - 4822 690 80123 >4.6 mW/cm 2 at 20 cm
S a M a1 b1 La L S S
M
10 x
2x
HINTS FOR REPAIRS - By interchanging it can be found out whether starters, lamps or ballasts are defective. If they are not, the internal wiring is to be checked, especially that on the tube holders. - The snap-on connections of the wiring can be unlocked with a paper clip. - The quick blackening of a tube-end points to a defective starter or a wiring fault. - Disassembly of radiation part Remove end cover (item 11, 2x). Remove cover (item 10) and acrylic plate (item 13). For removal of ballast or fan the pop rivets must be drilled out. New parts have to be fixed with pop rivets 4.8 mm or blind-rivetting nuts M3 (no service items).
- Disassembly of gasspring (item 18) Put solarium in highest position. Fasten ornamental screw (item 19) Now turn the stand and the radiation unit through so far that the legs of the stand and the radiation unit rest on the floor. Remove the nut inside the stand tube. Remove the ornamental screw and unlock the plastic guide block. Separate the inner and outer stand part. Remove the ornamental prop and the spring clip at the inner side of the stand and lift the pin out. The gasspring can be taken out now. Note: a new gasspring comes with plastic guide block, spring clip and ornamental prop. Disassembly of hinge (item 15) Remove the ornamental prop, spring clip and plastic ring. Polish the shaft with abrasive paper to make the removal of guide blocks easier. On assembly see to it that the cams of the spring clip rest in the groove on the shaft.
©
Published by Philips Domestic Appliances and Personal Care
Printed in The Netherlands
Copyright reserved
Subject to modification
4322 277 00366 00/08
HB 544/A
9 10 11
1 12 13 2
3 14
4 15 16 18+17 18 19 5 20 21 6 22 23 7 8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 4822 410 11079 4822 255 10255 4822 219 80258 4822 361 10966 4822 255 10254 9965 000 06405 4822 134 30014 4822 462 11193 4822 349 40068 4822 441 11963 4822 442 00006 9965 000 01865 4822 466 10705 4822 146 10344 4822 520 10789 timer knob lamp/starter holder S12 starter fan 230V lamp holder side panel TL 100W/Cleo U-shaped foot timer 60 mins cover end cover side panel with grip acrylic plate ballast 230V/100W bearing set 16 17 18 19 20 21 22 23 24 25 9965 000 02280 9965 000 02732 4822 529 10329 4822 502 13999 4822 255 10182 4822 255 10153 5322 219 80597 4822 134 30026 4822 142 60359 4822 528 10924 handgrip stand with gasspring gasspring orn. screw lamp holder starter holder S2 starter TL 15W/Cleo ballast 230V/30W swivel wheel
24 25
4822 690 80147 HB072 prot. goggles