Text preview for : 3M_MP8620_quicksetup_english.pdf part of 3M/Liesegang MP8620/DV710 Quicksetup manual (english) for 3M MP8620 or Liesegang DV710 projector
Back to : 3M_MP8620_quicksetup_engl | Home
3MP8620 Multimedia Projector Quick Setup Instructions
Cable Connections: Always turn power off when making any cable connections. 1. Power Cord 2. Computer 3. Mouse Emulation a) MS Mouse Port b) PS/2 Mouse Port 4. S-VHS 5. VCR
Technical Assistance & Product Information
Internet: [email protected]
1-800-328-1371
Procedure: 1. Turn off all power to projector and input sources before making any connections. 2. Connect cables (be careful not to bend any pins in cable connector plugs. 3. Start up projector then start up input sources.
©
3M 1997 78-6970-xxxx-x
3MP8620 Multimedia Projector Quick Setup Instructions
Projector Packout
Projector Startup Procedure 1. Lift cover locks (1) and raise top to open position. 2. Press the power switch (2) to ON. The red LED (4) illuminates. 3. Press the STANDBY button (3). The green LED (4) illuminates. 4. Check all ventilation slots and clear away any obstructions. 5. Turn the lens (5) to focus. 6. Press the foot lock button (6) to release height adjustment feet. Extend/retract feet (7) to for best image height. 7. Rotate feet (8) for fine adjustment. 8. Move projector closer or further away from screen to adjust width of projected image.
REVEAL BLANK FREEZE TIMER
Packout Items shown 1. Projector 2. Remote Control 3. VGA Cable 4. Mouse Cable 5. Power Cord
above: 6. PS/2 Mouse Adaptor 7. Audio Cable (RCA mini jack) 8. S-Video cable 9. RCA Video Cable 10. Soft Case
Remote Control Transmitter
Press to toggle projector between STANDBY mode (lamp off, fan off) and operation mode (lamp on, fan on). Press REVEAL to cover the image on the screen with a gray mask. Use the control stick to reveal the image or press REVEAL again to return full image. Stores (freezes) the projected image. Press again to return current image. Press MAGNIFY to double image size in horizontal and vertical directions. Press again to return image. Remove image (white background). Return image. Toggle between TIMER and data projection image. When TIMER is displayed, press ENTER and move control stick to adjust value. Press ENTER to start timer function. Display pointer. Operate control stick to move pointer. Press to adjust brightness image. Switch to video mode, then press again to select video source (video or s-video). Press to mute the speaker. Press again to return sound. Switch to PC mode. Press to adjust speaker volume. Display on-screen menu system (projector adjustments) Toggle mouse emulation ON/OFF . ON: The L and R buttons operate the left and right mouse key functions. Hold down L/R and operate control stick for drag and drop capability. OFF: L button is the ENTER confirmation key. R button not used. Control stick centers image. Mouse emulation ON, left mouse button. Emulation OFF, confirmation of selection. Mouse emulation ON, right mouse button. Mouse emulation ON, control stick moves on-screen pointer. OFF control stick centers image. ,
REVEAL FREEZE MAGNIFY BLANK TIMER
MAGNIFY
POINTER
VIDEO
PC
POINTER
MENU
Standby Mode 1. Press the STANDBY button (3). 2. The lamp will switch off and the red LED (4) will illuminate. 3. Press the STANDBY button (3) to illuminate lamp and project image. Projector Shutdown Procedure 1. Press the STANDBY button (3). (The lamp turns off, the fan motor continues to run)
!
ON/OFF
ENTER
VIDEO PC MENU
L
R
Caution
Do not turn off the projector power before pressing the STANDBY button. The fan motor will run for about 1 minute and cool the projector.
L/ENTER
R
8620-01A
2. After fan stops, press main power switch (2) to "OFF". 3. Lift cover locks (1) and lower cover into closed position to protect lens. 4. Disconnect cables to transport the projector.