Text preview for : solarium_©_.pdf part of Philips HB556/A, HB556/B Service Manual Solarium 1415W - pag. 4
Back to : solarium_©_.pdf | Home
Solarium HB556/A HB556/B
Philips Domestic Appliances and Personal Care
Service Manual
TECHNICAL INFORMATION Input consumption Lamp : approx. 1415 W / 230 V / 50 Hz : 6x TL Cleo Performance 100 W-S : 4x TL Cleo Performance 80 W-S : 1x HP400/H Starter Ballast Timer Radiation area Radiation distance Height adjustment Protecting goggles : 10x S12 : 1x ZG 4,5D : 7x 100 W / 230 V : 6x 80 W / 230 V : 1x 30 mins motor-driven : 174 x 58 cm : 20 cm : between 67 97 cm : HB071 4822 690 80123
L11a L11b L11c S11 La11 M1 SK3 TCO L La S M SK1
(HB556/A)
: 1x HP400/SH (HB556/B)
6x 100 W 4x 80 W
1x HPA 260 W
Output UVX36 meter : > 5.5 mW/cm² at 20 cm (HP400 on)
NTC1
= changed
C
M2
SK2
NTC
230 V / 50 Hz
Published by Philips Domestic Appliances and Personal Care
Printed in the Netherlands
© Copyright reserved
Subject to modification
03/02
HB556/A HB556/B
HINTS FOR REPAIRS - Interchange starters, lamps or ballasts to establish whether they are defective. - If they are not defective, check the internal wiring, especially that connected to the lamp holders. - The snap-on connections of the wiring can be detached by means of a paperclip. - Premature blackening of a tube end points to a defective starter or a wiring fault. - A burned NTC resistor or overheated wiring points to a wiring fault at the connecting block. Replacement of lamps/starters (items 33, 34 and 11) Loosen the screws (item 6) and remove the end covers (item 5). Pull the acrylic sheet (item 35) out of the appliance. Now the lamps/starters can be replaced. Disassembly of gas spring (item 8) Put the canopy in its highest position. Fasten ornamental screw (item 7). Remove the 2 screws (A). Lift the canopy off the foot together with a second person. Place the canopy on a soft surface. The gas spring can now be taken out. Disassembly of fan (item 13) Unlock the clamps of the fan cover (item 12). Loosen the connecting wires and pull out the fan unit (item 13). Disassembly of timer (item 20) Remove the end cover on the side where the timer is located. Pull the top cover on this side out of the groove of the side panel (item 17). Pull the side panel off the metal frame to create enough room to remove the timer. Disassembly of hinge (items 14, 15 and 16) Unlock the clamps of the hinge cover with a screwdriver. Loosen the screw (B). Ask a second person to depress the locks of the bearing bush (item 16) with two small screwdrivers. Position yourself on the other side of the appliance and press the stand with your foot while pulling the canopy slightly (approx. 5 mm) towards you to deactivate the lock. Now you and the other person should position yourselves at opposite ends of the appliance. Lift the canopy from the stand by pulling at it. Place the canopy on a soft surface. Remove the lock spring (item 15) Tap the bearing bush off the shaft with a plastic hammer. Disassembly of facial unit (item 24) Remove the fan, the end covers and the top cover. Contrary to what is indicated in the exploded view, a complete reflector unit with filter glass mounted in a metal frame is supplied as item 24.
2-4
HB556/A HB556/B
Pos 1 2 3 4 5 6 7 7a 8 9 10 11 12 13 14 15 16 17 18 19 Service code 4822 690 80123 4822 321 11395 9965 000 11524 9965 000 11518 9965 000 11523 4822 502 14539 9965 000 11530 9965 000 16367 9965 000 11527 9965 000 01934 9965 000 01933 4822 219 80258 9965 000 11521 9965 000 11520 9965 000 11528 9965 000 11525 9965 000 11526 9965 000 12129 4822 410 11079 9965 000 01946 = changed Description HB 071 protecting goggles mains flex top cover panel rear end cover s.t. screw 4.8 x 19 orn. screw stand gas spring lamp holder lamp/starter holder starter S12 fan cover fan complete hinge cap securing spring bearing bush panel front timer knob on/off switch Pos 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Service code 9965 000 11519 4822 252 20325 4822 134 10088 9965 000 16185 4822 325 20102 9965 000 12130 4222 062 94320 4822 214 12272 4822 271 30619 4222 062 94580 4222 062 94570 4822 146 10344 4822 146 10792 4222 062 94600 9280 032 21920 9280 043 21920 9965 000 11522 9965 000 11531 9965 000 11529 9965 000 11532 Description timer 30 mins aut. cut-out 100 °C HPA lamp HP400/H (/A) HPA lamp HP400/SH (/B) lamp holder reflector/filter unit fan HPA starter HPA micro switch NTC resistor 22 connector ballast 100 W ballast 80 W capacitor 50 µF/250 V TL Cleo Performance 80 W-S TL Cleo Performance 100 W-S acrylic sheet U-shaped foot swivel wheel mounting set
SK1 SK2 M
NTC 1 NTC 2
L11a
L11b
C1
L11c
L4
L1
N
N
L1
S11
La1 - 100 W La2 - 100 W La3 - 100 W La4 - 80 W
S1 S2 S3 S4 S5 S6 S7 S8 S9 S10
SK3
M2
La5 - 80 W La 11 La6 - 80 W La7 - 80 W La8 - 100 W La9 - 100 W La10 - 100 W
TCO
M1
L10
L9
L8
L7
L6
L5
L3
L2
L 230 V / 50 Hz N
N
N
L1
L1
L1
L1
3-4
HB556/A HB556/B
12 1 5
13
2
17 18
3 4
19 20 21 22 23 24
5
14 15 16
25 26
6 B
7
27 28
7a
29 30 31 32
8
33
34 9 10 11 35
A
36
37
4-4