Text preview for : 987685693.pdf part of Sony DSC-W5/W7/W15/W17 DSC-W5/W7/W15/W17 service manual L1/L2/L3
Back to : Sony DSC-W5.part1.rar | Home
DSC-W5/W7/W15/W17
Auto-ADJ
SERVICE MANUAL
Ver 1.1 2005.11
CORRECTION-1
We will inform you that there are printing errors in the service manual previously issued.
· Correction of the Before starting adjustment · Correction of the Table 6-1-1 · Correction of the Service tool
DSC-W5/W7/W15/W17
9-876-856-93
Sony EMCS Co.
2005K0500-1 © 2005.11 Published by DI Technical Support Department
! : Points deleted portion.
SECTION 6 ADJUSTMENTS
Before starting adjustment
(Service Manual Page 6-1)
^
EVR Data Re-writing Procedure When Replacing Board
The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 when replacing board.
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced.
(Machine before starting repair) PC PC (Machine after a board is replaced)
Save the EVR data to a personal computer.
Download the saved data to a machine.
Procedure 2
When the data cannot be saved due to defective flash memory, or when the flash memory cannot be removed or installed, save the data from the same model of the same destination, and download it.
(Machine to be repaired) PC (Machine to be repaired)
Download the data. Save the data.
(The same model of the same destination)
After the EVR data is saved and downloaded, check the respective items of the EVR data. (Refer to page 6-3 for the items to be checked.)
DSC-W5/W7/W15/W17 --2--
& : Points added portion. +
Precaution on Replacing the SY-001 board
· The Repair Board has already been adjusted. Re-initialization or EVR data copy from the set before repair is not required. · Perform "VIDEO OUT Default Data and Exif Model Data Check" mentioned below, and also the adjustment items necessary after SY Board replacement.
VIDEO OUT Default Data and Exif Model Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting. When the data has changed because of board replaceing etc, check the data setting (VIDEO OUT Default Data, Exif Model Data) is right. If not, rewrite to the right value.
VIDEO OUT Default Data Page 4F 4F Address 8D A2 Data NTSC 00 00 PAL 01 01
Exif Model Data Page 8F 8F Address E5 E6 Data DSC-W5 35 00 DSC-W7 37 00 DSC-W15 31 35 DSC-W17 31 37
Writing Method: 1) Select page: 00, address: 01 and set data: 01. 2) Select page: 4F, address: 8D and A2, and set the VIDEO OUT Dafault Data. 3) Select page: 8F, address: E5 and E6, and set the Exif Model Data. 4) Click [Save] on the SEUS screen. 5) Wait for more than 3 sec. 6) Select page: 80, address: 30, and check that the data is "00". 7) Select page: 00, address: 01, and set data: 00.
DSC-W5/W7/W15/W17 --3--
! : Points deleted portion.
1-1. Adjusting items when replacing main parts and boards
(Service Manual Page 6-3) When replacing main parts and boards, adjust the items indicated by z in the following table. Note 1: The automatic Adjustment Program does not support the "Initialization of data". Perform it manually. Note 2: Use the Color Adjustment Program (W5W15ColorAdjustment.exe or W7W17ColorAdjustment.exe). Note 3: When replacing the SY-001 board, erase the data in internal memory of the board before replacement. Note 4: When replacing the SY-001 board or the IC381 on the SY-001 board, execute formatting and initialize the internal memory after replacement. Note 5: CD board DSC-W5/W15 DSC-W7/W17 CD-545 CD-546
Replaced parts Block replacement Mounted parts replacement
(Timing gen., CCD signal process)
Board replacement
(32M AND flash) (Note 4)
(AF illumination LED)
CD-545/546 board (COMPLETE)
Adjusting item
Adjustment
CD-545/546 board IC101
CD-545/546 board D104
CH-168 board
CH-168 board
SY-001 board
SY-001 board
SY-001 board
SY-001 board
SY-001 board
LCD block
LCD block
Lens block
Flash unit
(COMPLETE) (Note 3, 4)
Back light unit
(Camera DSP)
(CCD imager)
(Video amp.)
LCD901 LCD unit
(LCD driver)
(COMPLETE)
IC101
IC301
IC801
IC601
IC381
D901
(Note 1) VIDEO adjustment CAMERA adjustment 1 CAMERA adjustment 2 (Note 2)
Initialization of data Video output level adj. Flange back adj. Flange back check Color shading adj. F No. compensation Measure gain adj. Mechanical shutter adj. Light value adj. AWB 3200K-5800K standard data input Color reproduction adj. & check CCD linearity check CCD white defect compensation check CCD black defect compensation check Strobe adj. Auto focus illumination check V-COM adj. White Balance adj.
z z z z z z z z
z
z z z z z z z z z
@
CAMERA adjustment 3
z
z
z
z z z
(Note 2)
z
z
z
z z z
CAMERA adjustment 4
z
z
z
z z z
CAMERA adjustment 5 LCD adjustment
z z z z
z z z z z
z z z z
Table 6-1-1
DSC-W5/W7/W15/W17 --4--
& : Points added portion. : Points changed portion. ! : Points deleted portion.
6-1. CAMERA SECTION ADJUSTMENTS
1-1. PREPARATIONS BEFORE ADJUSTMENTS
· AC power adapter 1-1-1. List of Service Tools (Service Manual Page 6-4) · Oscilloscope · Color monitor J-11 Connection code DK-2AA 1-830-351-11 J-12
@ *
AC power adaptor AC-LS5 1-479-284-12
Fig. 6-1-1
1-1-2. Preparations (Service Manual Page 6-5)
Note: Do not connect the A/V cable when perfoming the LCD system adjustment. AC power adaptor AC-LS5 (1-479-284-12) AC IN
To AV OUT jack (Note)
PC (The SEUS must be installed in the PC.)
OS: Windows 98/98SE/Me/2000/XP RAM: 256MB or more recommended USB: 2.0 recommended (also compatible with 1.1) Two connectors are required. Insert the connection cord DK-2AA (1-830-351-11). To USB connector
To USB connector
USB cable (1-827-038-11)
HASP Key
To USB connector Video system Adjustment Osilloscope Terminated 75 Color monitor Video (yellow) Audio (Black)
Fig. 6-1-4
DSC-W5/W7/W15/W17 --5--