shaver_Ž_.pdf part of Braun 4005 shaver_Ž_.pdf, Service Manual cord shaver

Text preview for : shaver_Ž_.pdf part of Braun 4005 Service Manual cord shaver - Pag. 8

Back to : shaver_Ž_.pdf | Home

Service Documentation Braun Pocket Twist Plus 375

Market Release 4/97

5615

5615

BINC Rev: 4/97 BAG Rev: 1/97

Service Documentation
Exploded Drawing 5615

5615 - 2

BINC Rev: 4/97 BAG Rev: 1/97

Service Documentation
Spare Parts List 5615 Part Description
Shaving foil frame Cutter block Cleaning brush

Pos. No.
7 8 24

Part Number
5614763 5524761 5524780

This shaver is a non-serviceable item. Refer to the Inventory Recommendations for Non-serviceable Products page in the Braun price book for article numbers when replacing the unit under warranty.

5615 - 3

BINC Rev: 4/97 BAG Rev: 1/97

Service Documentation
Service Information 5615

Technical Data Principle Housing Shaving head: Cutter block: Long hair trimmer: Drive: Power transmission: Power supply: Amplitude: Revolutions: Working current: Operating capacity: Dismantling Protective caps (1, 22): Remove cleaning brush (24). Take off screw (21). Pull apart the protective caps (1) and (22), and lever them, one after the other, from the housing shelves. To be unlocked through unlocking pins and to be removed. To be extracted. Remove circlip (9). Take off cutter block support (10) with ring seal and conical coil spring (11). 5615 - 4 Battery operated shaver with switch-on protection and foldable long hair trimmer. Plastic material Plastic frame with integrated shaving foil. 30 blades, 3° inclined, 10 mm diameter, plastic frame. Integrated in the housing upper part; can be additionally switched on by a separate slider. 2.7 V DC motor. via eccenter and oscillating frame onto the shaving system. by 2 Mignon batteries 1.5 V (type LR6, AM3, MN 1500/AA alkaline) Approx. 2.3 mm, measured at the cutter block. Approx. 6200 r.p.m. (with new batteries) Approx. 5500 r.p.m. (by 2.4 V minimum) Approx. 500 mA (without long hair trimmer) Approx. 60 shaving minutes.

Shaving foil frame (7): Cutter block (8): Cutter block support (10):

BINC Rev: 4/97 BAG Rev: 1/97

Service Documentation
Service Information 5615 Remove batteries. Unscrew the 3 housing screws (19). By means of a grip ring pliers inserted into the battery box, press apart the housing shelves (3) and (20), one after the other (see exploded drawing "A"). Attention: When opening the housing shelves, the spring catches (17) will snap out. Before extracting the motor, the slider (2) must be switched in the 'on' position. Snap out the motor from the direction of the eccenter and remove it together with the minus contact. Attention: When extracting the motor please take care that the spring wire (15) does not get lost. (Mostly the wire sticks to the motor through the magnetic effect.) All further dismantling steps do not require further explanation.

Open housing:

Motor (16):

Reassembly

The reassembly is made in reversed order. Attention must be paid to the following:

Battery contacts (13, 14):

Before inserting the plus contact (14) into the housing upper part (3), please absolutely make sure that the slider (2) is adjusted in the 'on' position. When inserting the battery contacts, care must be taken that the holes of the metal straps match exactly with the corresponding pins in the housing upper part (3). Insert the spring wire (15) before reassembling the motor (16, see drawing). Motor axis to be lubricated with a small amount of Vaseline underneath the eccenter. Reassemble the motor paying attention to the correct position of the poles. When inserting the motor into the housing upper part (3), the plus pole (soldered motor contact) must point upward. The minus pole must grip exactly into the contact spring "B" of the battery's minus contact (14). 5615 - 5

Spring wire (15):

Motor (16):

BINC Rev: 4/97 BAG Rev: 1/97

Service Documentation
Service Information 5615

Oscillating frame (12):

To be inserted into the housing lower part (20) in a way that the support for the long hair trimmer is pointing upward. The motor axis must be turned in a way that the eccentric stud is positioned in the center (flat part horizontally upward). Connect the housing halves in the shaving head area, paying attention to the fact that the eccentric stud must grip exactly into the long hole of the oscillating frame. After hanging in the battery cover, the housing halves are finally to be pressed together. Place the conical coil spring (11) on the oscillating frame (12). Then, pull the cutter block support (10) with the sealing over the housing bulge. To snap into the lateral pockets after the housing is reassembled, the snap-in pins pointing to the bottom of the appliance.

Housing:

Cutter block support (10):

Spring catches (17) with springs (18):

Attention!

Do not dispose of empty batteries in the household waste. Take them to special local collection sites. This product conforms to the EMC-requirements as laid down by the Council Directive (89/336/EEC). 5615 - 6

Compliance: