Text preview for : SAMSUNG CW593CWG8, CW5944N8, CW5944W8, CW683CNG8 Chassis KS3A.pdf part of Samsung CW593CWG8, CW5944N8, CW5944W8, CW683CNG8 Service Manual CW593CWG8, CW5944N8, CW5944W8, CW683CNG8
Back to : SAMSUNG CW593CWG8, CW5944 | Home
COLOR TELEVISION RECEIVER
Chassis : Model: KS3A CW593CWG8XXEG CW5944N8XXEC CW5944W8XXEG CW683CNG8XXEC
COLOR TELEVISION RECEIVER
CONTENTS
1. Precautions 2. Reference Information 3. Specifications 4. Alignment and Adjustments 5. Troubleshooting 6. Exploded View and Parts List 7. Electric Parts List 8. Block Diagrams 9. Wiring Diagram 10. Schematic Diagrams
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
LEAKAGE CURRENT TESTER
(READING SHOULD NOT BE ABOVE 0.5mA)
EARTH GROUND
Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called "horizontal disable" or "hold-down".) Heed the high voltage limits. These include the Xray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
Samsung Electronics
1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer's warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs "integral implosion" protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such "permanently attached" yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning1: First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.
Samsung Electronics
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power-- this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as "anti-static"; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
1-4
Samsung Electronics
Reference Information
2. Reference Information
2-1 Tables of Abbreviations and Acronyms
Table 2-1 Abbreviations A Ah Å dB dBm °C °F °K F G GHz g H Hz h ips kWh kg kHz k km km/h kV kVA kW I MHz Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz MV MW M m µA µF µH µm µs µW mA mg mH mI mm ms mV nF pF Ib rpm rps s V VA W Wh Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour
Samsung Electronics
2-1
Reference Information
Table 2-2 Table of Acronyms ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor
2-2
Samsung Electronics
Reference Information
2-2 IC Line Up
Table 2 - 3 IC Line - Up NO BOARD LOC. NO IC201S IC601 IC901 IC902 IC602 HIC201 HIC202 HIC203 HIC204 HIC401 IC301 Q402 Q401 D414 IC401 1 MAIN Q404 IC801S D801S PC801S IC802 D805 D806 D807 D802 IC201 IC804 IC803 IC903 IC904 Q909 Q910 TU01S TU02S Samsung Electronics TCLS3101PD09A9(S) TCPN3081PD09A(S) Main Tuner with IF Block Sub Tuner with IF Block Refer to Table 2-3-4 Refer to Table 2-3-5 2-3 FMG-G2CS KA78RM33 KA7806 KA78R08 KA78RM33 KIA7025AP 2N7000 3.3V Regulator 6V Regulator 8V Controlled Regulator 3.3V Regulator MICOM Reset IC IIC Level Shifter VDPY FML-G12S Rectifier Diode HC801 DDRI001 LA7845 KSC2073-H2 KSD5703 FMP-3FU KA393 IRF620 3S1265R RBV606 PC123Y KA78R05 SPS Controllor Bridge Diode Photo Coupler 5V Controlled Regulator E/W Drive IC Horizontal Drive IC HC401 100Hz Horizontal Pulse AMP Vertical IC Option DRGB001 RGB Drive AMP Hybrid IC SPEC VDP3112B MSP3411G SDA555X KS24L161 TDA7297 DESCRIPTION Video Processor Multistandard Sound Processor MICOM, TTX(MTP) EEPROM Audio AMP Refer to Table 2-3-3 VM Option REMARK Refer to Table 2-3-1 Refer to Table 2-3-2
Reference Information
Table 2 - 3 IC Line - Up NO 1 BOARD MAIN LOC. NO T801S T444S IC501 IC502 2 CRT IC503 QF04 QF05 QG02 QG03 ICG01 3 4 5 DOUBLE FOCUS V-S/W PIP ICP02 ICH01 QH01 ICS01 ICP01 2SC2344 2SA1011 KSA940 KSD2073-H2 KA4558 KA4558 2SC4636RB TEA6425 SDA9489X EZ1086CM OP-AMP (TILT) OP-AMP TR-Power Video Switching IC with Adder Output High-end Picture-In Picture IC 3.3V Regulator Option Option Option Push-Pull (VM) Option TR-Power (TILT) TDA6111Q Video Output AMP R.G.B Drive SPEC AA26-00046A FUJ-29B001 DESCRIPTION Trans Switching Trans FBT REMARK Refer to Table 2-3-6 Refer to Table 2-3-7
2-4
Samsung Electronics
Reference Information
Table 2-3-1 VIDEO IC (IC201S) SPEC VDP3108B VDP3112B VDP3120B VDP3130Y VDP3140D 50Hz Basic 50Hz, 2H Comb Filtr 50Hz, 2H Comb Filter, Horizontal Scaler 50Hz, 2H Comb Filter, DVD Input 100Hz FUNCTION REMARK
Table 2-3-2 SOUND IC (IC601) SPEC MSP3400D MSP3410D MSP3411G Multistandard, A2 Stereo Multistandard, A2 Stereo, Nicam Multistandard, A2 Stereo, Nicam, Vitual Dolby FUNCTION REMARK
Table 2-3-3 SOUND AMP (IC602) SPEC TDA7297 15W x 2CH, 10W x 2CH FUNCTION REMARK
Table 2-3-4 1'st TUNER (TU01S) SPEC TCLS3101PD09A(S) TCPS3001PD09D(S) TCPS3001PD09E(S) Note CS with LNA Function CS CS India FUNCTION Main REMARK
TCPS3001PD09A(S) is out-of-date, TCPS3001PD09D(S) which is up-to-date has the same function.
Table 2-3-5 2'nd TUNER (TU02S) SPEC TCPS3000PC09B(S) CS FUNCTION Sub REMARK
Samsung Electronics
2-5
Reference Information
Table 2-3-6 TRANS SPEC FUJ-29B001 FUH-29A001B 29" 21" FUNCTION REMARK
Table 2-3-7 TRANS FLYBACK (FBT) SPEC AA26-00046A AA26-00044C 29" 21" FUNCTION REMARK
2-6
Samsung Electronics
Specifications
3. Specifications
Television System
CS PAL/SECAM-B/G,D/K,L,I, NTSC-M 75ohms, Coaxial Cable 100W (Applied When 29" Flat) 220V Only Free Voltage Frequency 50/60Hz 15W x 2CH Output 10W x 2CH 5W x 2CH Vitual Dolby Effect Turbo Sound Pseudo Stereo RCA Input Front (AV2) S-VHS Head-Phone
Option Option 29 Inch 21 Inch Not Present R815
Antena Input
Consumption
Power
Requirements
Sound
Jacks
Back
2Scart Input/Output DVD Input(YPbPr) AV2 Monitor Audio Output S-VHS
AV1 : Scart I/O, RGB Input, RF Out AV2 : Scart I/O, Monitor Out
Option Option Option
Specifications are subject to change. Specifications for Model Name (Ex. CS29A6??8X/HAC) Function N P PF PT PW MT NT WT GW NICAM 2 TUNER PIP 2 TUNER PIP, NICAM, TTX 2 TUNER PIP, A2 STEREO, TTX 2 TUNER PIP, A2 STEREO 2 TUNER MULTI PIP, A2 STEREO, NICAM, TTX A2 STEREO, TTX 1 TUNER PIP, A2 STEREO, TTX "NICAM" means that A2 STEREO + NICAM NOTE
Samsung Electronics
3-1
Alignment and Adjustments
4. Alignment and Adjustments
4-1 General Alignment Instructions
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 8. To protect against shock hazard, use an isolation transformer. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.
4-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 10 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF. If color shading persists, perform the following Color purity and Convergence adjustments.
4-3 High voltage Check
CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level).
1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions.
Samsung Electronics
4-1
Alignment and Adjustments
4-4 Dynamic Focus Adjustment
1. A dynamic focus adjustment should be done after replacing the CRT PCB, FBT or CRT. 2. Input a crosshatch pattern.
3. Enter " STANDARD " in video mode. 4. Turn the Dynamic focus VR fully clockwise (maximum).( ) 5. Turn the Static focus VR fully counterclockwise (maximum).( ) 6. Slowly turn the static focus VR counterclockwise. Adjust until the vertical line in the middle of the screen has maximum clarity.( ) 7. Slowly turn the dynamic focus VR (clockwise) and adjust the 3rd horizontal line for maximum clarity.( ) 8. Repeat 4-7, if necessary.
H
STATIC FOCUS VR
V
DYNAMIC FOCUS VR
SCREEN
4-5 SCREEN Adjustment
1. Input Toshiba Pattern 2. Enter "Service Mode".(Refer to "Service Mode") 3. Select "G2-Adjust". 4. Set the values as below. 29 Inch IBRM = 220 WDRV = 35 CDL = 220 COLR G B = 150 150 150 21 Inch IBRM = 220 WDRV = 35 CDL = 165 COL = 70
4-2
Samsung Electronics
Alignment and Adjustments
5. Turn the SCREEN VR until "MRCR G B" and "MRWDG" are green and those value are about 100. (The incorrect SCREEN Voltage may result that "MRCR G B" and "MRWDG" should be red)
Note 1. When you do not have Toshiba Pattern, follow this method. 1. 2. 3. 4. 5. Set the TV on the condition that AV mode no signal(black) Enter the "Menu" and set the mode to blue screen off. Enter the "Service Mode". Select " G2-Adjust". Set the values as below. IBRM = 220 WDRV = 35 CDL = 220 COLR G B = 150 150 150 6. Turn the SCREEN VR until the value of " MRCR G B" is about 120. Do not mind that the "OSD" Color is red.
s After completing G2-Adjust, follow this procedure. x Enter the "Video Adjust 1". Choose any item in menu. (ex. Select "Red Cutoff") Change the value of item you select, and recover the value.
For example, when the value of "Red Cutoff" is 127, change the value to 128 and restore the value to 127. If you do not follow this procedure, the picture may be abnormal. For example, when the TV set is on, the picture becames brighter gradually.
Samsung Electronics
4-3
Alignment and Adjustments
4-6 E2PROM (IC902) Replacement
1. When IC902 is replaced, all adjustment data revert to the initial values. So, all adjustment values when servicing should be readjusted. 2. After IC902 is replaced, connect the AC power supply cord. 3. Turn the power switch ON. 4. In stand-by, warm up the TV for at least 10 seconds. 5. Power on the TV.
4-7 White Balance Adjustment
s Equipment : Color-Analyzer (CA-100) s Input Signal : Pattern signal (Toshiba pattern) 1. Select STANDARD from the menu. 2. Input an 100% White pattern. 3. Enter the "Service Mode". (Refer to "4-8 Service Mode") 4. Warm up the TV set at least for 30 minutes. 5. Input a Toshiba pattern signal. 6. Enter the "Video Adjust1". - Adjust "Sub Contrast" so that Y (luminance) becomes 40 ft ± 3. - Use "Red Drive" and " Blue Drive" to adjust High-Light (x : 290, y : 300) - Adjust "Sub Bright" so that Y (luminance) becomes 1.3ft ± 0.3. - Use "Red Cutoff" and "Blue Cutoff" to adjust Low-Light (x : 290, y : 300). 7. Adjust CA-100 so that the final adjustment value can be fixed. 8. Use the Channel Up/Down (v/w) buttons to move the cursor on the adjustment modes. 9. Use the Volume +/- buttons to change the adjustment value.
4-4
Samsung Electronics
Alignment and Adjustments
4-8 Factory Adjustment
4-8-1 Service Mode
1. To enter the "Service Mode", Press the remote-control keys in this sequence : - If you do not have Factory remote-control
PICTURE OFF DISPLAY ( ) MENU MUTE PICTURE ON
- If you have Factory remote-control
PICTURE ON DISPLAY ( ) FACTORY
2. After the Service Mode is entered, the initial screen is as shown in the figure below.
Service Deflection Video Adjust 1 Video Adjust 2 Video Adjust 3 Option(81h 0Ch) Reset G2-Adjust Others
*
These hexa * depends on digits are check sum value which the MICOM. If check sum value is changed, the value of 2 E PROM Data newly initialed.
3. Use the Channel Up/Down buttons to move the cursor in the adjustment parameters. Note 2. - When CRT, CRT PCB, FBT, E PROM (sometimes MICOM) is replaced, the adjustment values should be controlled. - After the Service adjustment is completed, Do not select "Reset" in the service mode menu. (After above procedure is done, power is on initially and the "Plug and Play" will be operated.)
2
Samsung Electronics
4-5
Alignment and Adjustments
4-8-2 Memory Data
4-8-2(A) DEFLECTION (GEOMETRIC ADJUSTMENT VALUE)
Fixed Value No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 OSD V Shift V Amp V Slope V SC H EW H Trapizium H Parabola H Symmetry H Corner H Shift PIP Contrast PIP Tint PIP PAL V Pos PIP NTSC V Pos PIP H Pos PIP BLKLG Range -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 0 ~ 15 0 ~ 63 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 15 Initial Value -30 -7 -3 -17 73 -47 -7 13 23 13 8 0 26 23 30 6 Function Adjust Vertical Picture Position Adjust Vertical Picture Size Adjust Vertical Slope Correction Adjust Vertical S-Correction Adjust Horizontal Picture Size Adjust Horizontal Trapeziod Adjust Horizontal Parabola Wave Adjust Horizontal Symmetry Adjust Horizontal Corner Adjust Horizontal Position Adjust PIP Contrast Adjust PIP Tinit Adjust PIP Vertical Position (Main Picture is PAL) Adjust PIP Vertical Position (Main Picture is NTSC) Adjust PIP Horizontal Position Adjust PIP Green Cutoff Level Not to be adjusted Not to be adjusted Remark
4-6
Samsung Electronics
Alignment and Adjustments
4-8-2(B) SCREEN CHANGE (I2C BUS GEOMETRIC ADJUSTMENT)
1
V Shift
6
V Amp
2
V Slope
7
V SC
3
H EW
8
H Trapizium
4
H Parabola
9
H Symmetry
5
H Corner
10
H Shift
Samsung Electronics
4-7
Alignment and Adjustments
4-8-2(C) VIDEO ADJUST 1
Fixed Value No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OSD Red Cufoff Green Cutoff Blue Cutoff Red Drive Green Drive Blue Drive Sub Bright Sub Contrast Sub Color Sub Tint BCL Threshold BCL Gain BCL Time TTX Contrast YC Delay Range Initial Value 0 ~255 0 ~255 0 ~255 0 ~255 0 ~255 0 ~255 0 ~ 200 0 ~ 13 0 ~ 27 0 ~ 100 0 ~ 255 0 ~ 15 0 ~ 15 0 ~ 255 0~8 127 127 127 127 127 127 100 50 27 80 65 8 9 90 * Adjust OSD/TTX Contrast Refer to Table 1 Adjust Beam Control Limit Refer to Note 3 Not to be adjusted Adjust Red Cutoff Level Adjust Green Cutoff Level Adjust Blue Cutoff Level Adjust Red Output Gain Adjust Green Output Gain Adjust Blue Output Gain Adjust Brightness Level Adjust Contrast Level Adjust Color Level Adjust Tint Low Light High Light High Light Low Light Function Remark
Note 3. Beam Control Limit Characteristic
beam
MIN 1.8mA 1.6mA BCL THESHOLD BCL GAIN MAX
WDRGB
50
IRE
Table 1. YC Delay Adjustment Table YC Delay Value PAL Def. 4 BG 3 DK 6 I 6 L 7 Def. 1 BG 1 SECAM DK 5 I 8 L 5 NTSC Def. 4 M 3
The "Def." means that TV is in AV mode.
4-8
Samsung Electronics
Alignment and Adjustments
4-8-2(D) VIDEO 2 ADJUST
Fixed Value No. 1 2 3 4 5 6 7 8 OSD B stretch-BTHR B stretch-BTLT B stretch-BAM Coring RGB Bright RGB Contrast EHT Time EHT Compensation Range 0 ~ 55 0 ~ 15 0 ~ 31 10 ~ 31 0 ~ 255 0 ~ 255 0 ~ 15 0 ~ 255 Initial Value 50 8 4 20 45 15 0 90 Black Stretch Threshold Black Stretch Tilt Position Black Stretch Amount Luma Peaking Filter Coring OSD/TTX RGB Bright OSD/TTX RGB Contrast Electronic High Tension Response Time Electronic High Tension Coefficient Function Remark
Coring : The Value of Center Frequency for the active bandwidth.
4-8-2(E) VIDEO 3 ADJUST
No. 1 2 3 4 5 6 7 OSD Peak Threshold Soft Limit Slope B Hard Limit Peak Video Ref Peak Video Gain Range Initial Value 0 ~ 255 0 ~ 15 0 ~ 255 0~4 0~5 185 4 255 0 0 33 39 Function White Peak Level Threshold Refer to Picture Below White Peak Level Threshold Reference White Peak Level Threshold Gain Auto Color Control Refer to Note Below Remark
ACC-REF(PAL/NTSC) 0 ~ 40 ACCR(SECAM) 0 ~ 39
Note 4. Soft Limit & Hard Limit
Output 511
Part 1
Part 2
Slope 1 [0...15]
Hard limiter
0 2 4 6 8 10 12 14
Slope 2 [0...15]
400
300
200
0 2 4 6 8 10 12 14
Soft Limit Slope B
range=256...511
"Soft Limit" is that Limitting the peak white without feed-back, but "Peak Limit" is that with feed-back for white peak level
100 tilt 1 [0...511] 0 0 100 200 300 400 500 600 700 800 900 tilt 2 [0...511] Li 1023
Samsung Electronics
4-9
Alignment and Adjustments
4-8-2(E) OPTION
Fixed Value No. 1 2 3 4 5 6 7 8 9 Language Sound CRT AV Mode X-Ray Tilt Control Auto FM PIP Txt Language OSD Initial Value Arab, Iran, Lybya, CIS A2/NICAM, V-Dolby, Mono, L-Stereo 4:3, Wide, Q(12.8:9), 4:3-16:9, Q-16:9 2Scart, 2Scart+S, 1RCA, 2RCA, 2RCA+S, 2RCA+D, 2RCA+S+D, 1Scart Off, On Off, On Off, On 2-Tuner, 1-Tuner, Off Arabic, Farsi, Arab-Hebrew, West Europe, East Europe, Russian, Greek-Turkey Off, On Off, On Off, On Off, On Without "TV/VIDEO" key in the front panel, set to "On" When PIP is "2-Tuner", set to "ON" Function Remark OSD Language
Depending on IC601 Refer to Note 5
S:S-VHS, D:DVD
10 11 12 13
LNA Equalizer High Deviate TTX On/Off
14
AV by CH key
Off, On
Initial Value : Refer to Note 6 on the next page.
Note 5. Sound A2/NICAM V-DOLBY Mono L-Stereo MSP3400D, MSP3410D MSP3411G Not used this mode for KS3A Chassis IC601
4-10
Samsung Electronics
Alignment and Adjustments
Note 6. Option. CS29A5WT8X/UMG Description LANGUAGE SOUND CRT AV MODE X-RAY TILT CONTROL AUTO FM PIP TEXT LANGUAGE LNA EQUALIZER HIGH DEVIATE TTX ON/OFF AV BY CH KEY OPTION BYTE Initial Vaue Arab V-Dolby 4:3 2 RCA + S OFF ON ON OFF Arabic OFF ON ON ON ON 84 CC D8 CS29A6PF8X/HAC Initial Vaue Arab V-Dolby 4:3 2 RCA + S OFF ON ON 2-Tuner Farsi ON ON ON ON OFF 85 DC 5E CS29A6WT8X/BWT Initial Vaue CIS A2/Nicam 4:3 2 SCART + S OFF ON ON OFF RUSSIAN OFF ON ON ON OFF 83 AC 28 CS29A5MT9X/BWT Initial Vaue CIS A2/Nicam 4:3 2 SCART + S OFF ON ON 2-Tuner RUSSIAN ON ON ON ON ON 83 AC AE
4-8-2(F) OTHERS
Fixed Value No. 1 2 3 4 5 6 7 8 OSD VSU H QEW H ZOOM Parabola H 16:9 Parabola TTX H Shift Range 96 ~ 111 -30 ~ 30 -30 ~ 30 -30 ~ 30 -30 ~ 30 Initital Value 98 0 8 -15 6 BG 2 8 Adjust Melody Volumn Adjust Horizontal Parabola in Zoom Mode Adjust Horizontal Parabola in 16:9 Mode Adjust Horizontal OSD/TTX Position Vertical Set Up Time Function Remark
Mono Sound System BG/DK/I/M V Slice Level Melody Volumn 0~3 0 ~ 20
Samsung Electronics
4-11
Alignment and Adjustments
4-9 MICOM
4-9-1 Pin Layout
Write Protect EEPROM SDA EEPROM SCL Bus-Stop Main SDA Main SCL Sound Reset Video Reset VDD 2.5V GND VDD 3.3V CVBS Input VDD 2.5V GND AFT Scart1 Ident Scart2 Ident Key 1 H-Sync V-Sync Key 3 Key 2 X-Ray Protect IR Input Stand-By LED Time LED
1 2 3 4 5 6 7 8 9 10 11 12 13 14
I/O I/O IO I/O I/O I/O I/O I/O
PWM I/O I/O
52 51 50 49 48 47 46 45
15 ADC 16 ADC 17 ADC 18 ADC 19 20 21 I/O 22 I/O 23 I/O 24 I/O 25 I/O 26 I/O
S D A 5 5 5 X
44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 I/O 27
Tilt N.C. Power Sound Mute N.C. N.C. PX. Y PX. Y VDD 3.3V GND VDD 2.5V CORE OSD-B OSD-G OSD-R VDD 2.5V GND X-TAL Out X-TAL In MICOM Reset N.C. N.C. VDD 3.3V GND N.C. Relay
4-12
Samsung Electronics
Alignment and Adjustments
4-9-2 Pin Assignment Specification
PIN NO FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 I/O I/O I/O I/O I/O I/O I/O I/O Vdd GND Vdd CVBS Vdd GND ADC ADC ADC ADC HS VS I/O I/O I/O I/O I/O I/O
ASSIGN Write Protect ROM SDA ROM SCL Bus Stop Main SDA Main SCL Sound Reset Video Reset VDD 2.5V
IN/OUT Out I/O I/O In I/O I/O Out Out
ACTIVE H/L Low
DESCRIPTION EEPROM Write Protection EEPROM Serial Data Line EEPROM Serial Clock Line
Low
Disable Micom IIC Peripheral IC Serial Data Line
Low Low
Peripheral IC Serial Clock Line MSP IC Initial Control VDP IC Initial Control
VDD 3.3V CVBS Input VDD 2.5V In TTX CVBS Input Analog B+ Analog Ground AFT SC1-ID SC2-ID Key1 H-Sync V-Sync Key3 Key2 X-Ray IR-In STD-LED TIM-LED In In In In In In In In In In Out Out Auto Fine Tuning Control Scart1 Ident Scart2 Ident Key1 Input Horizontal Sync Input Vertical Sync Input Key3 Input Key2 Input X-Ray Protection Remocon Signal Input LED Drive Output(Red) LED Drive Output(Green)
Samsung Electronics
4-13
Alignment and Adjustments
4-9-2 Pin Assignment Specification (Continued)
PIN NO FUNCTION 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 I/O N.C. GND Vdd N.C. N.C. Reset X-In X-Out GND Vdd R G B COR Vdd GND Vdd I/O I/O N.C. Not Used (Programmed Gound Level) N.C. I/O I/O N.C. I/O Tilt Out PWM S-Mute Power Out Out High Low Sound Amp Mute Picture On/Off Control Not Used (Programmed Gound Level) Tilt Control Output VDD 3.3V PX.Y PX.Y In When The Caption Function Adopted, Used. Out VDD 2.5V OSD-R OSD-G OSD-B CORE VDD 2.5V Out Out Out Out Reset X-TAL In X-TAL Out In In Out Low 6MHz 6MHz VDD 3.3V ASSIGN Relay
IN/OUT Out
ACTIVE H/L Low
DESCRIPTION Activate Degausssing Coil Not Used (Programmed Gound Level) Analog Ground Not Used (Programmed Gound Level) Not Used (Programmed Gound Level) Micom Hardware Reset Crystal Oscillation Input Crystal Oscillation Output Analog Ground Analog B+ OSD/TTX Output (Red) OSD/TTX Output (Green) OSD/TTX Output (Blue) Fast Blank/Half Contrast Output
4-14
Samsung Electronics
Plug in Power Cord
Samsung Electronics
ON Check LED lamp OFF Normal Normal Check and Replace the MICOM Normal Check and Replace IC903 Check IC901 MICOM Input Voltage Abnormal Normal Abnormal Check the MICOM Power #59 With Remote Controller Replace the MICOM Abnormal Replace Q908 Normal Normal Check IC802, IC803 Replace IC802, IC803 Normal Check IC201S VDP H-OUT #50 Abnormal Replace IC201S Normal Check Q401 H-TR Replace Q401 Normal Check 135V Line Check PC801S, IC801S Normal Replace FBT Abnormal Abnormal Check R828 and D805 Abnormal Check IC801S and FP801S Normal Check and Replace R828 or D805 Abnormal Check IC804 Input Voltage Abnormal Normal Check and Replace IC804 Check D801 and D811 Abnormal Abnormal Replace D801 or D811 Check IC903 3.3V Regulator Input Voltage Normal Replace Q908
5-1 No Power
5. Troubleshooting
Abnormal
Check MICOM IIC #5, #6
Check Level Shifter Q909, Q910 Output(If 2N7000 Output has the DC Component over 0.7V, it is broken)
Normal
Abnormal
Check MICOM IIC #2, #3
Abnormal
Replace Q909, Q910
Normal
Check IC902 EEPROM
Replace EEPROM(IC902)
Normal
Check IC201S
Note : When you check whether any component is normal, you must let the output pin be open in order not to be affected by the side of output.
Troubleshooting
5-1
No Picture, but sound is in normal operation
Normal
Turn the VR of FBT, higher screen voltage and Check the Deflection is in Normal Operation (If the deflection is in operation, flyback signal is appeared)
Abnormal
Normal
Check CRT PCB RK, BK, GK
Abnormal
Normal
Check IC201S #31
Abnormal
Check Heater Voltage Abnormal Normal Check CRT and FBT
Check HIC202, HIC203, HIC204 Output
Abnormal
Check 8V Check IC201S #63 or #59 Normal Abnormal Normal Normal
Abnormal
Check DZ202
Abnormal
Check CRT and FBT
Normal
Check IC803 Replace IC201S Check 200V, 16.5V Line Check Tuner CVBS Output Check IC301
Replace DZ202
Replace IC201S
5-2 No Picture
Troubleshooting
5-2
Samsung Electronics
Troubleshooting
5-3 No Sound
No Sound, but Picture is in normal operation
Normal
Check the CN602 Connection and Signal
Abnormal
Check the Speaker Wire Connection
Normal
Check 14V Line
Abnormal
Check IC602 #7 (If the pin is in low state, Sound is mute) Normal
Abnormal
Check FA803S
Check D816, Q906 Check IC601 #24, #25 Normal Replace IC602 Check IC601 Input Voltages (5V,8V) Normal Check the coils around IC601 Check IC601 Input Signal Normal Replace IC601 Check the Tuner Abnormal Abnormal Abnormal
Samsung Electronics
5-3
Exploded View& Part List
6. Exploded View & Parts List
6-1 CW5944N8XXEC
Samsung Electronics
6-1
Electrical Parts List
7. Electrical Parts List
7-1 CW593CWG8XXEG
Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark
ASSY-PCB,MAIN(OPT)
0.1 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ..2 ..2 ...3 ...3 ...3 ...3 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ..2 ..2 *HA94-100660ASSY-PCB,MAIN(OPT);CW593CW,KS3A/F V999S 3704-001105 SOCKET-CRT;11P,20PI,26.5PI,NI,CN501AAA39-20054BLEAD CONNECTOR-ASSY;-,YBNH025-06,S,6P,500,1007#26 CN502AAA39-20053BLEAD-CONNECTOR,ASSY;-,YBNH025-05,S,5P,500,1007#26 TOP AA39-20010B LEAD-CONNECTOR,ASSY;-,YFH800-01,S,1P,500,1617#22 IC501 HA96-00276B ASSY H/S;-,VIDEO AMP,AA62-00052A,STV510 1201-001687 IC-VIDEO AMP;STV5109,ZIP,15P,-,SIGLE,50dB,P AA62-00052AHEAT SINK-PS;,-,-,36*35*21,DC22,HA60-020004 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWRCH18 0205-000129 GREASE-SILICON;SC102,JAPAN T801S AA26-00046B TRANS SWITCHING;CODE-NO,CW6844N8X/XEF,-,AC90~2 IC201S1204-001633 IC-VIDEO PROCESS;VDP3112B,DIP,64P,-,PLASTIC,5V, TU01S AA40-00015ATUNER-F/S;TCPW3001PD09A(S),PAL/SECAM,TR, IC602 HA96-50398B ASSY-H/S;-,-,AA62-30182E,TDA7266S,1201-001308 IC-POWER AMP;7266,ZIP,15P,-,DUAL,26dB,PLAST AA62-30181F HEAT SINK-ES;-,AL6063 EXTR.,2,WHT,50MM,HA60-020007 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SWRCH1 0205-000129 GREASE-SILICON;SC102,JAPAN IC601 1204-001817 IC-SOUND PROCESSOR;MSP3400D-C5-G4-LH,DIP,52P,551M T444S AA26-30005UTRANS-FLYBACK;-,FUH-29A003,29,155V PT801S1404-001156 THERMISTOR-PTC;9OHM,+30%/-20%,220VRMS,270VAC, C806 2401-001137 C-AL;330uF,20%,400V,GP,BK,30x45mm,1 C405 2306-000178 C-FILM,MPPF;3.9nF,5%,1.6KV,BK,31x15x8.5,20 C406 2306-000253 C-FILM,MPPF;7.2nF,5%,1.6KV,TP,28.5x18.5x12 C426 2306-000188 C-FILM,MPPF;330nF,5%,400V,TP,26x19.5x11,20 L411 AA27-30001F COIL-LINEARITY;-,22uH,DR1011,PI0.45,25.5,-,20 L408 AA27-00056ACOIL HORIZ. WIDTH;-,600uH,YL9N 15x27.5 C:9.5,0.1 L405 AA27-00057ACOIL-HORIZ,WIDTH;-,10mH,YL-9N 15x27.5 C:9.5,0.3 C423 2306-000204 C-FILM,MPPF;430nF,5%,400V,TP,26x20.5x12. CX801S2306-000318 C-FILM,MPPF;220nF,20%,250V,TP,-,22.5mm CX802S2306-000318 C-FILM,MPPF;220nF,20%,250V,TP,-,22.5mm LX801SAA29-30002NFILTER-LINE NOISE;-,16MH,1.5A,AC100~260V,28-16MH LX802S AA29-30002N FILTER-LINE NOISE;-,16MH,1.5A,AC100~260V,28-16MH IC301 HA96-50406AASSY-H/S;-,-,AA62-30180K,LA7845,1204-000517 IC-VERTIVAL DEF.;LA7845,SIP,7P,-,PLASTIC,40V,11 AA62-30180K HEAT SINK-ES;-,A6063 EXTR,-,WHT,50/13,-,-,HA60-020007 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SWRCH1 0205-000129 GREASE-SILICON;SC102,JAPAN HC801 HA96-00274AASSY-H/S;-,COMPLEX,AA62-00053A,FMLG12S HA60-020004 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWRCH18 AA62-00053AHEAT SINK-PS;-,-,-,SILVER,HOLE 22mm,ALL, D802 0402-001230 DIODE-RECTIFIER;FMG-G2CS,1000V,3A,TO-220F,ST D805 0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,D806 0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,D807 0402-000233 DIODE-RECTIFIER;FML-G12S,200V,5A,-,IC802 1203-001006 IC-VOLTAGE REGULATOR;78R05,TO-220F,4P,-,PLASTIC,4. 0205-000129 GREASE-SILICON;SC102,JAPAN IC803 1203-001697 IC-VOLTAGE REGULATOR;78R08,TO-220,4P,-,PLASTIC,7.8 IC804 HA96-00243C ASSY-H/S;-,REGULATOR,AA62-00045A,KA7806 1203-000284 IC-POSI.FIXED REG.;7806,TO-220,3P,-,PLAS HA60-020007 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SWRCH1 AA62-00065AHEAT SINK-PS;DP,-,-,-,AA62-00045A,-,-,-,-,0205-000129 GREASE-SILICON;SC102,JAPAN IC902 1103-001171 IC-EEPROM;24L161,16KBIT,DIP,8P,300MIL,10 IC901 AA09-00135AIC MICOM;SIM806EW1-A040,CW29A6,52P,-0.3 IC801SHA96-50371C ASSY-H/S;-,-,AA62-30181H,KA3A1265R,AA13-00101AIC HYBRID;KA3A1265RD,CN5039,5Pin,-50to12 AA61-10386ABRACKET-IC;-,-,SECC 100,T1.0,-,KA2S0680,AA62-30197DHEAT SINK-ES;DP,-,-,-,AA62-30181H,-,-,HA60-020007 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SWRCH1 HA68-500033 LABEL-WARNING;A/P(90G),W33,H18,WHT 0205-000129 GREASE-SILICON;SC102,JAPAN IC903 1203-001944 IC-POSI.FIXED REG.;78RM33,TO-220,3P,-,PL C407 2301-001338 C-FILM,MPE-PPF;0.68nF,5%,1.6kV,TP,28x7x11mm,2 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 5 1 1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 1 1
..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3
D801S 0402-001399 DIODE-BRIDGE;GSIB660,600V,6A,SIP-4,BKQ402 0502-001007 TR-POWER;KSC2073-H2,NPN,25W,TO-220,ST,6 PC801S0604-001038 PHOTO-COUPLER;TR,130-260%,200MW,DIP-4,ST NT802S1404-001045 THERMISTOR-NTC;4.7OHM,15%,2900K,35.0MW,T C815 2401-003026 C-AL;330uF,20%,200V,GP,ST,22x35,10 CY802S2201-002002 C-CERAMIC,DISC;4700pF,20%,400V,+20%~-55%,TP,2 JA701 3722-000195 JACK-SCART;42P,-,SN,BLK,NO C820 2401-003076 C-AL;3300uF,20%,50V,WP,BK,18x35.5mm R807 2006-001083 R-CEMENT;120ohm,5%,5W,CJ,TP,14x10x27mm L808 AA27-10002L COIL-CHOKE;-,24UH,K,-,2A,-,24UH-K,10X10MM IC401 1202-000103 IC-VOLTAGE COMP.;393,DIP,8P,300MIL,DUAL,36V,CMO Q404 0505-000156 FET-SILICON;IRF620,N,200V,5A,0.8ohm,50W,TO HA98-600010 ASSY-SUB,PART;S51A,PCB-MAIN 0202-000008 SOLDER-WIRE;S63S-W3.0,S63S,D3,SN63/PB37 0202-000187 SOLDER-WIRE FLUX;-,RS60S,D1.2,63SN/37PB 0204-001024 FLUX;DF-96TVS,-,20%,0204-000442 SOLVENT;1M-1000,C3H70H,96,HA99-100684 ASSY-PCB,MAIN(ACI);CW593C,KS3A/F 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C105 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C101 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C103 2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C228 2301-000356 C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C230 2301-000356 C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C809 2301-000356 C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C810 2301-000356 C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C811 2301-000356 C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5mm C202 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C205 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C920 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C231 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C215 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C630 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C631 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C645 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C652 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C603 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C708 2401-002235 C-AL;10UF,20%,16V,GP,TP,5X11MM,5MM C214 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C216 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C605 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C620 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C635 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C646 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C829 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C837 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C839 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C916 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C308 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C914 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C831 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C825 2305-000665 C-FILM,MPEF;100NF,5%,63V,TP,7.5X4.0X5.0MM, C208 2401-001026 C-AL;3.3uF,20%,50V,GP,TP,5x11mm,5mm C217 2401-001026 C-AL;3.3uF,20%,50V,GP,TP,5x11mm,5mm C636 2401-001026 C-AL;3.3uF,20%,50V,GP,TP,5x11mm,5mm C905 2202-000796 C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C607 2202-000796 C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C608 2202-000796 C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C903 2202-000796 C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C923 2202-000796 C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C211 2202-000796 C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,3.5x19,C212 2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5m C416 2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5m C213 2301-000247 C-FILM,PEF;33nF,5%,50V,TP,8.1x4.5x13mm,5m C218 2202-000632 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C219 2202-000632 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C220 2202-000632 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,-
1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 6 8 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Samsung Electronics
7-1
Electrical Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3
C221 C222 C223 C901 C921 C922 C919 C924 C511 C233 C234 C235 C907 C909 C237 C841 C604 C201 C303 C224 C225 C304 C305 C821 C902 C307 C302 C401 C403 C421 C402 C404 C408 C414 C418 C422 C424 C601 C610 C611 C415 C612 C613 C617 C917 C413 C622 C625 C626 C628 C707 C623 C624 C627 C629 C642 C644 C701 C638 C639 C632 C504 C505 C506 C634 C826 C832 C838 C637 C640 C641 C643 C647 C649 C804 C805 C807
2202-000632 2202-000632 2202-000632 2202-000632 2202-000632 2202-000632 2202-000632 2202-000632 2202-000632 2305-000412 2305-000412 2305-000412 2305-000412 2305-000412 2401-000914 2401-000603 2401-000603 2401-000603 2201-002031 2201-002031 2201-002031 2305-000285 2305-000149 2301-000192 2301-000192 2401-000360 2401-000360 2201-000556 2201-000556 2201-000556 2401-001397 2401-001397 2305-000382 2401-002597 2401-002597 2401-001527 2201-000132 2201-000558 2301-000445 2301-000445 2301-000445 2401-001914 2401-001914 2401-000493 2401-000493 2401-000493 2401-001264 2401-001264 2401-001264 2401-001264 2401-001264 2202-000231 2202-000231 2202-000231 2202-000231 2202-000231 2202-000231 2202-000231 2202-000231 2202-000231 2202-000806 2202-000806 2202-000806 2202-000806 2401-001840 2401-001840 2401-001840 2401-001840 2401-000027 2401-000027 2401-000027 2401-000027 2202-000286 2301-000108 2201-000332 2201-000332 2301-001397
C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP,2.5x4.3,C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-AL;22uF,20%,16V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;1uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,DISC;5pF,0.25pF,50V,NPO,TP,5x3mm,5m C-CERAMIC,DISC;5pF,0.25pF,50V,NPO,TP,5x3mm,5m C-CERAMIC,DISC;5pF,0.25pF,50V,NPO,TP,5x3mm,5m C-FILM,MPEF;220nF,5%,100V,TP,20x18x11.5,15 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5,5 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-AL;100uF,20%,50V,GP,TP,8x11.5,5 C-AL;100uF,20%,50V,GP,TP,8x11.5,5 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4,5 C-AL;470uF,20%,25V,GP,10x16mm,5mm,T C-AL;470uF,20%,25V,GP,10x16mm,5mm,T C-FILM,MPEF;4.7NF,5%,400V,TP,-,5MM C-AL;220uF,20%,35V,GP,TP,10x12.5,5 C-AL;220uF,20%,35V,GP,TP,10x12.5,5 C-AL;47uF,20%,250V,HR,TP,13x25mm,5m C-CERAMIC,DISC;100pF,10%,500V,Y5P,TP,6x4,5 C-CERAMIC,DISC;470pF,10%,50V,Y5P,TP,5x3,5 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-AL;1uF,20%,50V,BP,TP,5x11,5 C-AL;1uF,20%,50V,BP,TP,5x11,5 C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP,3.5x19,C-CERAMIC,MLC-AXIAL;220PF,10%,50V,Y5P,TP,3.5*19,C-CERAMIC,MLC-AXIAL;220PF,10%,50V,Y5P,TP,3.5*19,C-CERAMIC,MLC-AXIAL;220PF,10%,50V,Y5P,TP,3.5*19,C-CERAMIC,MLC-AXIAL;220PF,10%,50V,Y5P,TP,3.5*19,C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;56pF,5%,50V,SL,TP,1.9x3.5,C-FILM,PEF;1.5nF,5%,50V,TP,6.5x3.0x5.5mm, C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7 C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,11x7,7 C-FILM,PPF;2.2nF,5%,1.2kV,TP,15x8.5x13.5m
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3
C814 C816 C817 C819 C822 C818 C910 C911 C913 C915 C918 C210 D201 D202 D207 D208 D209 D210 D211 D602 D804 DZ402 D906 D405 D501 D502 D503 D508 D604 KEZI D301 D411 D803 D816 D401 D404 D402 D403 D406 D810 D811 D907 D504 D413 D801 DZ201 DZ202 DZ802 DZ902 DZ601 DZ603 DZ903 DZ904 DZ905 DZ906 DZ907 DZ604 DZ605 DZ908 DZ909 DZ910 DZ203 DZ302 DZ303 DZ304 DZ305 DZ306 DZ804 DZ401 DZ801 DZ808 DZ805 GT101 GT102 GT301 GT302 GT401
2201-000406 C-CERAMIC,DISC;270pF,10%,2KV,Y5P,TP,8x6,7.5 2401-000293 C-AL;100uF,+30-10%,200V,HR,TP,16x25 2201-000599 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5 2201-000599 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5 2201-000599 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4,5 2401-000722 C-AL;2200uF,20%,25V,WT,TP,16x25,7.5 2201-000980 C-CERAMIC,DISC;30pF,5%,50V,CH,TP,5.0x3.0,5mm 2201-000980 C-CERAMIC,DISC;30pF,5%,50V,CH,TP,5.0x3.0,5mm 2401-000287 C-AL;100uF,20%,16V,WT,TP,6.3x11,5 2401-000287 C-AL;100uF,20%,16V,WT,TP,6.3x11,5 2401-000287 C-AL;100uF,20%,16V,WT,TP,6.3x11,5 2401-000287 C-AL;100uF,20%,16V,WT,TP,6.3x11,5 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0401-000005 DIODE-SWITCHING;1N4148,75V,300MA,DO-35,TP 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,TP 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP 0402-000534 DIODE-RECTIFIER;RG10V,400V,1.2A,DO-201,TP 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP 0402-000537 DIODE-RECTIFIER;RH1A,600V,0.6A,DO-204AC 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-204AC,TP 0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-000508 DIODE-ZENER;BZX79C5V6,5.6V,5%,500mW,DO0403-001321 DIODE-ZENER;MTZJ6.8C,6.66-7.01V,500mW,DO-3 0403-001329 DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW,DO0403-001329 DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW,DO0403-001329 DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW,DO0403-001221 DIODE-ZENER;UZ39BSB,35.36-37.19V,500MW,DO0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,TP 0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,TP 0403-001325 DIODE-ZENER;MTZJ15C,14.35-15.09V,500mW,DO0403-001322 DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO-3 0403-001322 DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO-3 1203-001217 IC-POSI.ADJUST REG.;431,TO-92,3P,4.58MIL,PLASTIC,2 AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
7-2
Samsung Electronics
Electrical Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3
GT402 GT801 GT802 GT803 GT804 GT805 GT806 GT103 GT409 GT501 GT502 GT503 J102 J103 J105 J108 J110 J111 J112 J113 J114 J115 J116 J117 J119 J122 J123 J124 J203 J205 J206 J207 J208 J209 J210 J212 J213 J214 J215 J216 J217 J218 J219 J222 J223 J224 J225 J226 J227 J228 J229 J230 J232 J234 J236 J237 J238 J239 J242 J244 J246 J247 J248 J401 J402 J404 J406 J409 L410 J412 J414 J416 J418 J421 J422 J424 J428
AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO AA60-40014APIN-GT,ASSY;1P,-,-,AUTO 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3
J601 J602 J603 J604 J606 J607 J611 J614 J615 J616 J617 J618 J619 J620 J621 J622 J624 J627 J629 J631 J632 J703 J704 J709 J708 J715 J716 J717 J805 J806 J807 J810 J811 J816 J819 J820 J821 J822 J823 J824 J825 J826 J829 J830 J831 J832 J833 J908 J909 J911 J912 J913 J915 J916 J917 J924 J925 J926 J927 J928 J932 J933 J934 J936 J939 J941 J942 R939 J714 J249 D908 J835 J425 J633 J818 J612 L610
3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219 3812-000219
WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Samsung Electronics
7-3
Electrical Parts List
Loc. No.
Code No.
Description ; Specification
Remark
Loc. No.
Code No.
Description ; Specification
Remark
...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ..