Text preview for : SONY DSR-PD170, PD170P, PD190P SERVICE MANUAL VER 1.5 2008.09 (9-876-286-16).pdf part of SONY DSR-PD170 SONY DSR-PD170, PD170P, PD190P
DIGITAL CAMCORDER.
SERVICE MANUAL VERSION 1.5 2008.09
PART#(9-876-286-16)
Back to : SONY DSR-PD170, PD170P, P | Home
DSR-PD170/PD170P /PD190P
RMT-811
SERVICE MANUAL
Ver. 1.5 2008. 09
Revision History How to use Acrobat Reader
US Model Canadian Model
DSR-PD170
AEP Model UK Model E Model
DSR-PD170P
Chinese Model
DSR-PD190P
Photo : DSR-PD170
C MECHANISM
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAMS SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST ADJUSTMENTS
· INSTRUCTION MANUAL is shown at the end of this document. · Reference No. search on printed wiring boards is available.
DIGITAL CAMCORDER
DSR-PD170/PD170P/PD190P
SPECIFICATIONS
Video camera recorder
System Video recording system 2 rotary heads Helical scanning system Audio recording system Rotary heads, PCM system Quantization: Fs32 kHz (12 bits, channels 1/2, channels 3/4), Fs48 kHz (16 bits, channels 1/2) Video signal DSR-PD170: NTSC color, EIA standards DSR-PD170P/PD190P: PAL colour, CCIR standards Usable cassette Mini DVCAM cassette with the mark printed Mini DV cassette with the mark printed Tape speed DVCAM format: Approx. 28.218 mm/s DV format SP mode: Approx. 18.812 mm/s Recording/playback time (using cassette PDVM-40ME) DVCAM format: 40 min DV format SP mode: 1 h Fast-forward/rewind time (using cassette PDVM-40ME) Approx. 2 min and 30 s Viewfinder Electric viewfinder (B&W) Image device 1/3 type CCD (3 Charge Coupled Device) DSR-PD170: Approx. 380 000 pixels (Effective: Approx. 340 000 pixels) DSR-PD170P/PD190P: Approx. 450 000 pixels (Effective: Approx. 400 000 pixels) Lens Combined power zoom lens Filter diameter 58 mm (2 3/8 in) 12× (Optical), 48× (Digital) F1.6 - 2.4
Focal length 6 - 72 mm (1/4 - 2 7/8 in) When converted to a 35 mm still camera 43.2 - 518.4 mm (1 3/4 - 20 1/2 in) Color temperature Auto, nIndoor (3 200 K), Outdoor (5 800 K), Minimum illumination 1 lux (F1.6) Input/Output connectors S VIDEO input/output Input/output auto switch 4-pin mini DIN Luminance signal: 1 Vp-p, 75 ohms, unbalanced DSR-PD170: Chrominance signal: 0.286 Vp-p, 75 ohms, unbalanced DSR-PD170P/PD190P: Chrominance signal: 0.3 Vp-p, 75 ohms, unbalanced VIDEO input/output Input/output auto switch RCA pin-jack, 1 Vp-p, 75 ohms, unbalanced AUDIO CH1/CH2 input/output Input/output auto switch RCA pin-jack, 327 mV, (at output impedance more than 47 kilohms) Output impedance with less than 2.2 kilohms Input impedance more than 47 kilohms Headphones jack Stereo minijack (ø 3.5 mm) LANC control jack Stereo mini-minijack (ø 2.5 mm) INPUT1/INPUT2 connectors XLR 3-pin, female, 60 dBu: 3 kilohms, +4 dBu: 10 kilohms (0 dBu = 0.775 Vrms) DV Interface 4-pin connector Speaker Dynamic speaker (ø 20 mm) LCD screen Picture 6.2 cm (2.5 type) Total dot number 211 000 (960 × 220)
General Peak inrush current (DSR-PD170P/PD190P) Hot switching inrush current, measured in accordance with European standard EN55103-1: 6.3 A (230 V) Power requirements 7.2 V (battery pack) 8.4 V (AC Adaptor) Average power consumption (when using the battery pack) During camera recording using LCD 5.4 W Viewfinder 4.7 W Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Storage temperature 20 °C to +60 °C (4 °F to +140 °F) Dimensions (approx.) 133 × 180 × 456 mm (5 1/4 × 7 1/8 × 18 in) (w/h/d) Mass (approx.) 1.6 kg (3 lb 9 oz) including the hood with a lens cap 1.7 kg (3 lb 12 oz) including the NP-F330 rechargeable battery pack, cassette PDVM-40ME and microphone Supplied accessories See page 5-39.
Rechargeable battery pack NP-F330
Output voltage DC 7.2 V Capacity 5.0 Wh Dimensions (approx.) 38.4 × 20.6 × 70.8 mm (1 9/16 × 13/16 × 2 7/8 in) (w/h/d) Mass (approx.) 70 g (2.5 oz) Type Lithium ion
Wide conversion lens VCL-HG0758
Lens power 0.7 Lens structure 3 groups, 3 elements Screw thread for video camera recorder M58 × 0.75 Dimensions Maximum diameter : ø 93 mm (3 3/4 in) Length : Approx. 48 mm (1 15/16 in) Mass (excluding the caps) Approx. 418 g (14 oz) Supplied accessories Lens caps (2) (for the front and back of the lens) Carrying pouch (1) Design and specifications are subject to change without notice.
AC Adaptor AC-L15A/L15B
Power requirements 100 - 240 V AC, 50/60 Hz Current consumption 0.35 - 0.18 A Power consumption 18 W Output voltage DC OUT: 8.4 V, 1.5 A Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Storage temperature 20 °C to +60 °C (4 °F to +140 °F) Dimensions (approx.) 56 × 31 × 100 mm (2 1/4 × 1 1/4 × 4 in) (w/h/d) excluding projecting parts Mass (approx.) 190 g (6.7 oz) excluding power cord
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
--2--
DSR-PD170/PD170P/PD190P
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
2. 3.
4.
5. 6.
: LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
--3--
DSR-PD170/PD170P/PD190P
TABLE OF CONTENTS 1. SERVICE NOTE
1-1. NOTE FOR REPAIR ······················································· 1-1 1-2. POWER SUPPLY DURING REPAIRS ·························· 1-2 1-3. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) ····························································· 1-2 1-4. SELF-DIAGNOSIS FUNCTION ···································· 1-3 1-4-1. Self-diagnosis Function ··················································· 1-3 1-4-2. Self-diagnosis Display ····················································· 1-3 1-4-3. Self-diagnosis Code Table ··············································· 1-4 · LA-028 (1/3) (ZOOM/FOCUS DRIVE) SCHEMATIC DIAGRAM ···························· 4-19 · SE-147 (VAP SENSOR) SCHEMATIC DIAGRAM ···························· 4-19 · LA-028 (2/3) (VAP DRIVE) SCHEMATIC DIAGRAM ···························· 4-21 · LA-028 (3/3) (KEY IN/CONNECTOR) SCHEMATIC DIAGRAM ···························· 4-23 · FP-188, FP-189 FLEXIBLE SCHEMATIC DIAGRAM ···························· 4-23 · KP-013 (SELECT DIAL) SCHEMATIC DIAGRAM ···························· 4-25 · MK-016 (CONTROL KEY) SCHEMATIC DIAGRAM ···························· 4-25 · MS-209 (MS CONNECTOR) SCHEMATIC DIAGRAM ···························· 4-25 · FK-088 (CONTROL SWITCH) SCHEMATIC DIAGRAM ···························· 4-27 · XZ-003 (LITHIUM BATTERY, SW) SCHEMATIC DIAGRAM ···························· 4-29 · LB-100D (BACK LIGHT) SCHEMATIC DIAGRAM ···························· 4-31 · HL-013 (LCD DRIVE) SCHEMATIC DIAGRAM ···························· 4-33 · FP-195, FP-196 FLEXIBLE SCHEMATIC DIAGRAM ···························· 4-33 · FP-205 FLEXIBLE SCHEMATIC DIAGRAM ···························· 4-34 · MA-430D (AUDIO AMP) SCHEMATIC DIAGRAM ···························· 4-35 · FP-896 FLEXIBLE SCHEMATIC DIAGRAM ···························· 4-35 · DD-216D (1/2) (DC/DC CONVERTER) SCHEMATIC DIAGRAM ···························· 4-37 · DD-216D (2/2) (DC REGURATOR) SCHEMATIC DIAGRAM ···························· 4-39 · CONTROL SWITCH BLOCK (CF-4980, PS-4980) SCHEMATIC DIAGRAM ···························· 4-41 · RM-091 (REAR REMOTE COMMANDER RECEIVER) SCHEMATIC DIAGRAM ···························· 4-43 · VC-358D (1/18) (S/H AGC, TG) SCHEMATIC DIAGRAM ···························· 4-45 · VC-358D (2/18) (CAMERA SIGNAL PROCESS) SCHEMATIC DIAGRAM ···························· 4-47 · VC-358D (3/18) (MS I/F) SCHEMATIC DIAGRAM ···························· 4-49 · VC-358D (4/18) (RS 232C I/F, STILL CONTROL) SCHEMATIC DIAGRAM ···························· 4-51 · VC-358D (5/18) (MS DRIVE) SCHEMATIC DIAGRAM ···························· 4-53 · VC-358D (6/18) (DV SIGNAL PROCESS) SCHEMATIC DIAGRAM ···························· 4-55 · VC-358D (7/18) (DV INTERFACE) SCHEMATIC DIAGRAM ···························· 4-57 · VC-358D (8/18) (REC/PB AMP) SCHEMATIC DIAGRAM ···························· 4-59 · VC-358D (9/18) (LINE IN/OUT) SCHEMATIC DIAGRAM ···························· 4-61 · VC-358D (10/18) (LINE A/D) SCHEMATIC DIAGRAM ···························· 4-63 · VC-358D (11/18) (RGB DRIVE/TG) SCHEMATIC DIAGRAM ···························· 4-65 · VC-358D (12/18) (CAMERA CONTROL) SCHEMATIC DIAGRAM ···························· 4-67 · VC-358D (13/18) (MECHANISM CONTROL) SCHEMATIC DIAGRAM ···························· 4-69
2.
DISASSEMBLY
2-1. LCD SECTION (HL-013, PD-217 BOARDS, INVERTER TRANSFORMER UNIT) ··························· 2-2 2-2. EVF SECTION (LB-100D BOARD) ······························ 2-3 2-3. (UPPER) HANDLE BLOCK ASSEMBLY ···················· 2-4 2-4. FK-088, MA-430D, RM-091, XD-003, XS-004, XM-005, XZ-003 BOARDS ··········································· 2-5 2-5. CABINET (L) BLOCK ASSEMBLY, MECHANISM DECK, VC-358D, DD-216D, JK-267 BOARDS (FOR FORCE EJECT OF CASSETTE AND VTR SECTION CHECK) ························································ 2-7 2-6. CABINET (R) BLOCK ASSEMBLY ····························· 2-9 2-7. CABINET BOTTOM ASSEMBLY ································ 2-9 2-8. BATTERY PANEL BLOCK ASSEMBLY (MK-016, KP-013, MS-209 BOARDS) ······················· 2-10 2-9. EVF BLOCK ASSEMBLY ··········································· 2-10 2-10. LA-028, DD-216D, VC-358D, JK-267 BOARDS, MECHANISM DECK ··················································· 2-11 2-11. LENS BLOCK ASSEMBLY, CENTER FRAME ASSEMBLY ··································· 2-12 2-12. CD-512, SE-147 BOARDS, ZOOM LENS ASSEMBLY ···· 2-13 2-13. CONTROL SWITCH BLOCK (PS-4980), CONTROL SWITCH BLOCK (CF-4980) ··················· 2-13 2-14. CK-140 BOARD ··························································· 2-14 2-15. CONTROL SWITCH BLOCK (ED-4980), HINGE ASSEMBLY ····················································· 2-15 2-16. CIRCUIT BOARDS LOCATION ································· 2-16 2-17. FLEXIBLE BOARDS LOCATION ······························ 2-17
3.
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7.
BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (1/4) ··························· 3-1 OVERALL BLOCK DIAGRAM (2/4) ··························· 3-3 OVERALL BLOCK DIAGRAM (3/4) ··························· 3-5 OVERALL BLOCK DIAGRAM (4/4) ··························· 3-7 POWER BLOCK DIAGRAM (1/3) ································ 3-9 POWER BLOCK DIAGRAM (2/3) ······························ 3-11 POWER BLOCK DIAGRAM (3/3) ······························ 3-13
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/3) ······················· 4-1 FRAME SCHEMATIC DIAGRAM (2/3) ······················· 4-3 FRAME SCHEMATIC DIAGRAM (3/3) ······················· 4-5 4-2. SCHEMATIC DIAGRAMS · CD-512 (CCD IMAGER) SCHEMATIC DIAGRAM ···························· 4-11 · JK-267 (JACK BOARD) SCHEMATIC DIAGRAM ···························· 4-13 · CK-140 (KEY IN) SCHEMATIC DIAGRAM ···························· 4-15 · FP-194, FP-197 FLEXIBLE SCHEMATIC DIAGRAM ···························· 4-16 · CONTROL SWITCH BLOCK (ED-4980) SCHEMATIC DIAGRAM ···························· 4-16 · PD-217 (RGB DRIVE, TG) SCHEMATIC DIAGRAM ···························· 4-17
--4--
DSR-PD170/PD170P/PD190P
· VC-358D (14/18) (DRUM/CAPSTAN MOTOR DRIVE) SCHEMATIC DIAGRAM ···························· 4-71 · VC-358D (15/18) (HI CONTROL) SCHEMATIC DIAGRAM ···························· 4-73 · VC-358D (16/18) (AU LINE A/D, D/A) SCHEMATIC DIAGRAM ···························· 4-75 · VC-358D (17/18) (LINE AMP) SCHEMATIC DIAGRAM ···························· 4-77 · VC-358D (18/18) (CONNECTOR) SCHEMATIC DIAGRAM ···························· 4-79 · XD-003 (DC/DC CONVERTER, REMOTE COMMANDER RECEIVER) SCHEMATIC DIAGRAM ···························· 4-81 · XS-004 (MIC SELECT) SCHEMATIC DIAGRAM ···························· 4-81 · XM-005 (MIC AMP) SCHEMATIC DIAGRAM ···························· 4-83 4-3. PRINTED WIRING BOARD · CD-512 (CCD IMAGER) PRINTED WIRING BOARD ······················· 4-89 · FP-594 FLEXIBLE BOARD ···································· 4-91 · JK-267 (JACK BOARD) PRINTED WIRING BOARD ······················· 4-93 · CK-140 (KEY IN) PRINTED WIRING BOARD ······················· 4-95 · PD-217 (RGB DRIVE, TG) PRINTED WIRING BOARD ······················· 4-97 · FP-194 FLEXIBLE BOARD ····································· 4-97 · LA-028 (ZOOM/FOCUS DRIVE, VAP DRIVE, KEY IN/CONNECTOR) PRINTED WIRING BOARD ······················· 4-99 · SE-147 (VAP SENSOR) PRINTED WIRING BOARD ····················· 4-101 · FP-188 FLEXIBEL BOARD ··································· 4-101 · FP-189 WIRING BOARD ········································ 4-101 · MS-209 (MS CONNECTOR) PRINTED WIRING BOARD ····················· 4-103 · KP-013 (SELECT DIAL) PRINTED WIRING BOARD ····················· 4-105 · MK-016 (CONTROL KEY) PRINTED WIRING BOARD ····················· 4-105 · FK-088 (CONTROL SWITCH) PRINTED WIRING BOARD ····················· 4-107 · XM-005 (MIC AMP) PRINTED WIRING BOARD ····················· 4-109 · LB-100D (BACK LIGHT) PRINTED WIRING BOARD ····················· 4-111 · HL-013 (LCD DRIVE) PRINTED WIRING BOARD ····················· 4-113 · FP-196 FLEXIBLE BOARD ··································· 4-113 · MA-430D (AUDIO AMP) PRINTED WIRING BOARD ····················· 4-115 · DD-216D (DC/DC CONVERTER, DC REGURATOR) PRINTED WIRING BOARD ····················· 4-117 · XZ-003 (LITHIUM BATTERY, SW) PRINTED WIRING BOARD ····················· 4-119 · RM-091 (REAR REMOTE COMMANDER RECEIVER) PRINTED WIRING BOARD ····················· 4-121 · VC-358D (S/H AGC, TG, CAMERA SIGNAL PROCESS, MS I/F, RS 232C I/F, STILL CONTROL, MS DRIVE, DV SIGNAL PROCESS, DV INTERFACE, REC/PB AMP, LINE IN/OUT, LINE A/D, RGB DRIVE/TG, CAMERA CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, HI CONTROL, AU LINE A/D, D/A, LINE AMP, CONNECTOR) PRINTED WIRING BOARD ····················· 4-123
· XS-004 (MIC SELECT) PRINTED WIRING BOARD ····················· 4-127 · XD-003 (DC/DC CONVERTER, REMOTE COMMANDER RECEIVER) PRINTED WIRING BOARD ····················· 4-129 4-4. WAVEFORMS ···························································· 4-130 4-5. MOUNTED PARTS LOCATION ······························· 4-135
5.
REPAIR PARTS LIST
5-1-1. OVERALL SECTION-1 ················································· 5-3 5-1-2. OVERALL SECTION-2 ················································· 5-4 5-1-3. CABINET (L) SECTION ················································ 5-5 5-1-4. CABINET (R) SECTION-1 ············································ 5-6 5-1-5. CABINET (R) SECTION-2 ············································ 5-7 5-1-6. UPPER HANDLE SECTION ········································· 5-8 5-1-7. BATTERY PANEL SECTION ········································ 5-9 5-1-8. EVF SECTION ······························································ 5-10 5-1-9. CENTER FRAME SECTION ······································ 5- 11 5-1-10. LENS BLOCK SECTION ············································· 12 5-1-11. CASSETTE COMPARTMENT, DRUM AND REEL TABLE ASSEMBLY ····················································· 5-13 5-1-12. TAPE GUIDE, PINCH SLIDER ASSEMBLY AND BRAKE SLIDER ASSEMBLY ····································· 5-14 5-1-13. EACH GEARS AND LOADING/CAPSTAN MOTOR ASSEMBLY ·································································· 5-15 5-2. ELECTRICAL PARTS LIST ········································ 5-16
6.
ADJUSTMENT
1. Before starting adjustment ··············································· 6-1 1-1. Adjusting items when replacing main parts and boards. ···· 6-2 6-1. CAMERA SECTION ADJUSTMENT ······························ 6-4 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) ··················································· 6-4 1-1-1. List of Service Tools ······················································· 6-4 1-1-2. Preparations ····································································· 6-6 1-1-3. Precaution ········································································ 6-8 1. Setting the Switch ···························································· 6-8 2. Order of Adjustments ······················································ 6-8 3. Subjects ··········································································· 6-8 1-2. INITIALIZATION OF A, B, C, D, E, F, 8 PAGE DATA ···· 6-9 1-2-1. INITIALIZATION OF A, C, D, 8 PAGE DATA ············· 6-9 1. Initializing the C, D, 8 Page Data ···································· 6-9 2. Modification of C, D, 8 Page Data ·································· 6-9 3. C Page Table ···································································· 6-9 4. D Page Table ·································································· 6-11 5. 8 Page Table ··································································· 6-12 6. Initializing the A Page Data ··········································· 6-12 1-2-2. INITIALIZATION OF B PAGE DATA ························· 6-13 1. Initializing the B Page Data ··········································· 6-13 2. Modification of B Page Data ········································· 6-13 3. B Page Table ·································································· 6-13 1-2-3. INITIALIZATION OF E, F PAGE DATA ····················· 6-14 1. Initializing the E, F Page Data ······································· 6-14 2. Modification of E, F Page Data ····································· 6-14 3. F Page Table ·································································· 6-14 4. E Page Table ·································································· 6-16 1-3. CAMERA SYSTEM ADJUSTMENTS ························ 6-17 1. 27MHz Origin Oscillation Adjustment (VC-358D board) ·························································· 6-17 2. Zoom Key Center Adjustment ······································· 6-17 3. HALL Adjustment ························································· 6-18 4. Offset Adjustment ·························································· 6-18 5. Flange Back Adjustment (Using Minipattern Box) ······· 6-19 6. Flange Back Adjustment ··············································· 6-20 6-1. Flange Back Adjustment (1) ············································· 6-20 6-2. Flange Back Adjustment (2) ············································· 6-20 7. Flange Back Check ························································ 6-21
--5--
DSR-PD170/PD170P/PD190P
8. Picture Frame Setting ···················································· 6-21 9. Pre White Balance Data Input ······································· 6-22 10. Auto White Balance Standard Data Input ····················· 6-22 11. MAX GAIN Adjustment ··············································· 6-23 12. LV Standard Data Input ················································· 6-23 13. White Balance ND Filter 1 Compensation ···················· 6-24 14. White Balance ND Filter 2 Compensation ···················· 6-24 15. Auto White Balance Adjustment ··································· 6-25 16. Color Reproduction Adjustment (ND Filter OFF) ········ 6-25 17. Color Reproduction Adjustment (ND Filter 1) ·············· 6-26 18. Color Reproduction Adjustment (ND Filter 2) ·············· 6-26 19. White Balance Check ···················································· 6-27 20. Steady Shot Adjustment ················································ 6-28 20-1. Steady Shot Adjustment (1) ··········································· 6-29 20-2. Steady Shot Adjustment (2) ··········································· 6-30 1-4. ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT ····························································· 6-31 1. VCO Adjustment (VC-358D board) ······························ 6-31 2. Bright Adjustment (1) (VC-358D board) ······················ 6-32 3. Bright Adjustment (2) (VC-358D board) ······················ 6-32 4. Contrast Adjustment (VC-358D board) ························ 6-33 1-5. LCD SYSTEM ADJUSTMENT ··································· 6-34 1. VCO Adjustment (PD-217 board) ································· 6-34 2. Bright Adjustment (PD-217 board) ······························· 6-35 3. Black Limit Adjustment (PD-217 board) ······················ 6-35 4. PSIG GRAY Adjustment (PD-217 Board) ···················· 6-36 5. Contrast Adjustment (PD-217 board) ···························· 6-36 6. Center Level Adjustment (PD-217 board) ····················· 6-37 7. V-COM Adjustment (PD-217 board) ···························· 6-37 8. White Balance Adjustment (PD-217 board) ·················· 6-38 6-2. MECHANICAL SECTION ADJUSTMENT ··············· 6-39 2-1. PARTS REPLACEMENT AND PREPARATION FOR ADJUSTMENT ···················································· 6-39 2-1-1. Outline ··········································································· 6-39 1. Manual test ·········································································· 6-39 2. Step test ··············································································· 6-39 3. Auto test ··············································································· 6-39 2-1-3. Mode Selector II (A-6082-282-A) Connection ············· 6-39 2-1-2. Mechanism Condition (Position) Shifting Order List ··· 6-39 2-1-4. The Mechanical Adjustment Requires the Following Tools ······················································· 6-40 2-2. PARTS REPLACEMENT ············································· 6-41 2-2-1. Tape Fall Stopper, HC Roller and HC Arm ··················· 6-41 2-2-2. Drum Assembly and Drum Base Block Assembly ········ 6-41 2-2-3. Damper Assembly, Cassette Compartment Assembly and Extension Spring ··························································· 6-42 2-2-4. Reel Table (S) / Reel Table (T) Assembly ····················· 6-43 2-2-5. Cassette Base Block Assembly, Gooseneck Gear Assembly and Relay Gear ············································· 6-43 2-2-6. TG1 Adjustment Plate Assembly, Tension Coil Spring (TG1), TG1 Arm Assembly, TG7 Retainer Spring and TG7 Arm Block Assembly ············································ 6-44 2-2-7. Brake Slider Assembly, Pinch Slider Assembly and Cam Gear ······································································· 6-44 2-2-8. Pinch Arm Assembly, Torsion Spring (TG7LD), Pinch Press Arm and Eject Arm ···································· 6-45 2-2-9. GL Block Assembly, GL Driving Gear and HC Driving Arm ··································································· 6-45 2-2-10. Capstan Motor, Conversion Pulley, Timing Belt and Holder ············································································ 6-46 2-2-11. L Motor Block Assembly and FP-594 Flexible Board ····· 6-47 2-2-12. Reset Arm (S), Brake (S), Brake Rack (S), Brake (T), Brake Gear (T), Brake Spring (T) and Extension Spring ··· 6-48 2-2-13. Coaster (S) / (T) Assembly, GL Arm (S) / (T) Assembly, Guide Rail, GL Gear (S) / (T) and Torsion Spring (GLS) / (GLT) ······································· 6-49
2-2-14. L Motor Assembly, Motor Shield, FP-248 Flexible Board, TG1 Spring Hook, Spring Hook Fulcrum Base, Spring Hook Driving Arm, Worm Shaft, Deceleration Gear and Motor Holder ················································· 6-50 2-3. CHECK AND ADJUSTMENT ····································· 6-51 2-3-1. FWD Position Checking and Adjustment ····················· 6-52 2-3-2. FWD Back Tension Checking and Adjustment ············· 6-52 2-2-3. Reel Table (S) / Reel Table (T) Torque Check ·············· 6-53 2-3-4. Preparation for Tape Path Checking and Adjustment ···· 6-54 2-3-5. Track Checking and Adjustment ··································· 6-55 2-3-6. TG7 Slack Checking and Adjustment ··························· 6-55 2-3-7. Curl Checking and Adjustment ····································· 6-56 2-3-8. CUE / REV Check ························································· 6-56 2-3-9. Rising Check ································································· 6-56 2-4. PERIODIC CHECK ······················································ 6-57 2-4-1. Cleaning of Rotary Drum Assembly ····························· 6-57 2-4-3. Periodic Checks ····························································· 6-57 2-4-2. Cleaning of Tape Path System ······································· 6-57 6-3. VIDEO SECTION ADJUSTMENTS ··························· 6-58 3-1. PREPARATIONS BEFORE ADJUSTMENTS ············ 6-58 3-1-1. Equipment Required ······················································ 6-58 3-1-2. Precautions on Adjusting ··············································· 6-59 3-1-3. HOW TO ENTER RECORD MODE WITHOUT CASSETTE ··································································· 6-59 3-1-4. HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE ··································································· 6-59 3-1-5. Adjusting Connectors ···················································· 6-60 3-1-6. Connecting the Equipment ············································ 6-60 3-1-7. Alignment Tapes ··························································· 6-61 3-1-8. Input/Output Level and Impedance ······························ 6-61 3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT ········ 6-62 1. Initialization of A, B, C, D, E, F, 8 Page Data ··············· 6-62 2. Serial No. Input ····························································· 6-62 2-1. Company ID Input ························································· 6-62 2-2. Serial No. Input ····························································· 6-62 3. Battery End Adjustment ················································ 6-64 3-3. SERVO AND RF SYSTEM ADJUSTMENT ··············· 6-65 1. Cap FG Duty Adjustment (VC-358D board) ················ 6-65 2. T reel FG Duty Adjustment (VC-358D board) ············· 6-65 3. PLL f0 & LPF f0 Adjustment (VC-358D board) ·········· 6-65 4. Switching Position Adjustment (VC-358D board) ········ 6-66 5. AGC Center Level and APC & AEQ Adjustment ········· 6-66 5-1. Preparations before adjustments ···································· 6-66 5-2. AGC Center Level Adjustment (VC-358D board) ········ 6-66 5-3. APC & AEQ Adjustment (VC-358D Board) ················ 6-67 5-4. Processing after Completing Adjustments ···················· 6-67 6. PLL f0 & LPF f0 Final Adjustment (VC-358D board) · 6-67 3-4. VIDEO SYSTEM ADJUSTMENTS ····························· 6-68 3-4-1. Base Band Block Adjustments ······································ 6-68 1. Chroma BPF f0 Adjustment (VC-358D board) ············· 6-68 S VIDEO OUT Y Level Adjustment (VC-358D board) ····· 6-68 2. 3. S VIDEO OUT Chroma Level Adjustment (VC-358D board) ·························································· 6-69 4. VIDEO OUT Y, Chroma Level Check (VC-358D board) ·························································· 6-69 3-4-2. BIST Check ·································································· 6-70 1. Playback System Check ················································ 6-70 1-1. Preparations for Playback ·············································· 6-70 1-2. IC301 TRX (RF) PB BIST Check ································· 6-70 1-3. IC301 AUD (ABUS) PB BIST Check ··························· 6-70 1-4. IC301 VFD PB BIST Check ········································· 6-70 1-5. IC301 ENCODER BIST Check ···································· 6-71 1-6. Processing after Completing Playback System Check ···· 6-71 3-5. AUDIO SYSTEM ADJUSTMENTS ···························· 6-72 1. Playback Level Check ··················································· 6-73 2. Overall Level Characteristics Check ····························· 6-73
--6--
DSR-PD170/PD170P/PD190P
3. 4. 5. 6-4. 4-1. 1. 2. 4-2. 4-3. 1. 2. 2-1. 2-2. 3. 4. 5. 6. 7. 8. 9.
Overall Distortion Check ··············································· 6-73 Overall Noise Level Check ············································ 6-73 Overall Separation Check ·············································· 6-73 SERVICE MODE ·························································· 6-74 ADJUSTMENT REMOTE COMMANDER ················ 6-74 Using the adjustment remote commander ····················· 6-74 Precautions upon using ·················································· 6-74 the adjustment remote commander ································ 6-74 DATA PROCESS ··························································· 6-75 SERVICE MODE ·························································· 6-76 Setting the Test Mode ···················································· 6-76 Emergence Memory Address ········································ 6-76 EMG Code (Emergency Code) ····································· 6-76 MSW Code ···································································· 6-77 Bit value discrimination ················································ 6-78 Switch check (1) ···························································· 6-78 Switch check (2) ···························································· 6-79 Switch check (3) ···························································· 6-79 Record of Use check ······················································ 6-80 Record of Self-diagnosis check ····································· 6-80 HRS METER (Hours meter) ········································· 6-81
* Color reproduction frame is shown on page 307.
--7--
DSR-PD170/PD170P/PD190P SECTION 1 SERVICE NOTE
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When remove a connector, don't pull at wire of connector. It is possible that a wire is snapped.
When installing a connector, don't press down at wire of connector. It is possible that a wire is snapped.
Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside)
1-1
DSR-PD170/PD170P/PD190P
1-2. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so that the unit cannot operate. These following two methods are available to prevent this. Take note of which to use during repairs. Method 1. Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the "ADJ" side. Method 2. Use the DC IN terminal. (Use the AC power adaptor.)
1-3. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1 2 3 4 5 6 Refer to page 2-4 to remove the upper handle block assembly. Refer to page 2-7 to remove the cabinet (L) assembly. Refer to page 2-7 to remove the mechanism deck (Including VC-358D board and DD-216D board). Remove DD-216D board from the mechanism deck (Including VC-358D board). Remove the CN022 (27P 0.3 mm) of VC-358D board. Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
DC power supply (+4.5V)
: loading : unloading
Disconnect from CN022 (27P) of VC-358D board.
Loading motor
What to do when a user forgets a password
This camcorder has the forced log insertion function. A password is inputted, and this function is set up. When this function was set up, this camcorder doesn't move if the memory stick which memorize a correct logo isn't inserted. To release the forced logo function, the correct password must be input. This password is memorized in the IC1105 (EEPROM) on VC-358D board. Therefore, when a user forgets the password, replace the IC1105. This IC1105 memorizes the HRS METER data (Hour meter data: page A, address 00 to 13), too. Therefore, replace the IC1105 in the following order to copy the HRS METER data. Replacing procedure: 1) Note down the data of page A, address 00 to 13. 2) Replace IC1105 (EEPROM) on VC-358D board. 3) To page A, address 00 to 13, input the data noted down. (Refer to "9. HRS METER (Hours meter)" of "6-4. SERVICE MODE")
1-2
DSR-PD170/PD170P/PD190P
1-4. SELF-DIAGNOSIS FUNCTION
1-4-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder, LCD screen or LCD window what to do. This function consists of two display; self-diagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.
Viewfinder or LCD screen
C:31:11
1-4-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the viewfinder, LCD screen or LCD window consists of an alphabet and 4-digit numbers, which blinks at 3.2 Hz. This 5-character display indicates the "repaired by:", "block" in which the problem occurred, and "detailed code" of the problem.
LCD window
C : 3 1 : 11
Blinks at 3.2Hz
C
Repaired by: C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer
31
Block
11
Detailed Code
Refer to page 1-4. Indicates the appropriate Self-diagnosis Code Table. step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.
Note: The "self-diagnosis display" data will be backed up by the coin-type lithium battery of XZ-003 board BT801, 802. When the (upper) handle block is removed, the "self-diagnosis display" data will be lost by initialization.
1-3
DSR-PDD170/PD170P/PD190P
1-4-3. Self-diagnosis Code Table
Self-diagnosis Code
Repaired by:
Block Detailed Function Code 0 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 0 0 0 1 1 2 2 2 2 2 3 4 4 9 9 9 1 1 2 2 2 2 2 3 4 4 9 9 9 0 0 0 0 1 0 1 2 3 4 0 0 2 7 8 9 0 1 0 1 2 3 4 0 0 2 7 8 9
Symptom/State
Correction
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum. FG fault during normal drum operations. Mechanical position fault. Mechanical position fault. Mechanical position fault. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum FG fault during normal drum operations Mechanical position fault. Mechanical position fault. Mechanical position fault. Difficult to adjust focus (Cannot initialize focus.)
Use the info LITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Inspect the lens block focus reset sensor (Pin wg of LA-028 board) when focusing is performed when the focus ring is rotated in the focus manual mode, and the focus motor drive circuit (IC140 of LA-028 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (Pin ws of LA-028 board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC140 of LA-028 board) when zooming is not performed. Inspect pitch angular velocity sensor (SE601 of SE-147 board) peripheral circuits. Inspect yaw angular velocity sensor (SE600 of SE-147 board) peripheral circuits.
E
6
1
0
0
E
6
1
1
0
Zoom operations fault (Cannot initialize zoom lens.) Steadyshot function does not work well. (With pitch angular velocity sensor output stopped.) Steadyshot function does not work well. (With yaw angular velocity sensor output stopped.)
E
6
2
0
0
E
6
2
0
1
1-4E
DSR-PD170/PD170P/PD190P SECTION 2 DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. LCD section (HL-013, PD-217 boards, Inverter transformer unit) HL-013, PD-217 boards service position
2-2. EVF section (LB-100D board)
LB-100D board service position
2-3. (Upper) handle block assembly
2-4. FK-088, MA-430D, RM-091, XD-003, XS-004, XM-005 boards FK-088, MA-430D, RM-091, XD-003, XS-004, XM-005 boards service position
2-5. Cabinet (L) block assembly, Mechanism deck, VC-358D, DD-216D, JK-267 boards (for force eject of cassette and VTR section check)
Mechanism deck service position-1
DSR-PD170/PD170P/PD190P
2-13. Control switch block (PS-4980), Control switch block (CF-4980)
Service position to check the VTR section
2-6. Cabinet (R) block assembly
CK-140 board service position
2-7. Cabinet bottom assembly
2-14. CK-140 board
2-8. Battery panel block assembly (MK-016, KP-013, MS-209 boards)
2-15. Control switch block (ED-4980), Hinge assembly
2-9. EVF block assembly
2-10. LA-028, DD-216D, VC-358D, JK-267 boards, Mechanism deck
2-11. Lens block assembly, Center frame (D) assembly
Service position to check the camera section
2-12. CD-512, SE-147 boards, Zoom lens assembly
[Connection diagram for service position (Mainly for voltage measurement and check)] (CK-140, VC-358D, JK-267, CD-512, DD-216D, LA-028, KP-013, MK-016, MS-209 boards, Mechanism deck-2)
2-1
DSR-PD170/PD170P/PD190P
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. LCD SECTION (HL-013, PD-217 BOARDS, INVERTER TRANSFORMER UNIT)
REMOVING THE PD-217 BOARD, INVERTER TRANSFORMER UNIT
4 Harness (CP-093) (8P) 6 LCD frame, BL retainer, FP-196 flexible board 5 Harness (CP-094) (14P) qa Remove the three solderings qh Inverter transformer unit 1 FP-195 flexible board (7P)
7 -21 PD oard B
2 Two screws (M2 × 3), lock ace
3 P cabinet (C) (D) assembly
q; HL-013 board 9 Release the two claws and slide the HL-013 board in the direction of the arrow B. qs Two screws (M2 × 3), lock ace qd Panel holder 7 Release the two claws and slide the indication panel block assembly in the direction of the arrow A. A 8 Indication panel block assembly 6 FP-205 flexible board (21P)
B
qa Screw (M2 × 3), lock ace
q; Screw (M1.7 × 2.5), lock ace qj PD-217 board
qd PCB clip
qf PCB clip qg Remove the six solderings 7 Two screws (M1.7 × 2.5), lock ace qs Back light Cold cathode fluorescent tube 9 Liquid crystal indicator module (24P) 8 P cabinet (M) assembly 2 Two screws (M2 × 5), lock ace 3 Three claws
5 FP-196 flexible board (5P)
7 -21 PD oard B
1 Two screws (M2 × 5), lock ace 4 FP-195 flexible board (7P)
[HL-013, PD-217 BOARDS SERVICE POSITION]
HL-013 board Indication panel block assembly (21P) CN007 20
1 Adjustment remote commander (RM-95) LANC jack
2 Claw
FP-196 flexible board (5P)
7 -21 PD oard B
FP-195 flexible board (7P) PD-217 board Inverter transformer unit AC POWER ADAPTOR
3 CPC cover
CPC-13 jig (J-6082-443-A) AC IN
1 Screw (M2 × 5), lock ace
2-2
DSR-PD170/PD170P/PD190P
2-2. EVF SECTION (LB-100D BOARD)
2 EVF rear cabinet assembly 4 EVF front cabinet (upper) 1 Push the lock knob in the direction of the arrow A and remove the EVF rear cabinet assembly in the direction of the arrow B.
B
6
A
3 Two tapping screws (M1.7 × 8) 5 EVF front cabinet (lower) assembly
REMOVING THE LB-100D BOARD
2 LCD (LCX033APA-1)(16P) 9 LCD (LCX033APA-1) 4 Two claws 1 FP-193 flexible board (27P) qs LCD holder assembly
3 Two claws qa LCD cushion q; Light interception sheet 8 Prism sheet 7 Illuminator 5 Lamp guide (20)
6 LB-100D board
[LB-100D BOARD SERVICE POSITION]
Adjustment remote commander (RM-95)
LCD holder assembly LB-100D board
CPC-13 jig (J-6082-443-A) LANC jack AC POWER ADAPTOR AC IN
2-3
DSR-PD170/PD170P/PD190P
2-3. (UPPER) HANDLE BLOCK ASSEMBLY
9 (Upper) handle block assembly
4 Tilt up the finder. 2 Two screws (M2 × 5), lock ace 3 Screw (M2 × 5), lock ace 1 Two screws (M2 × 5), lock ace 5 Screw (M2 × 5), lock ace
6 Tilt down the finder.
7
8 FP-895 flexible board (40P)
2-4
DSR-PD170/PD170P/PD190P
2-4. FK-088, MA-430D, RM-091, XD-003, XS-004, XM-005, XZ-003 BOARDS
1 RM-091 board (21P)
3 MA-430D board (23P)
1 Three screws 4 Handle cover (D) assembly (M2 × 5), lock ace 5 RM-091 board (7P) 7 Tapping screw (B2 × 5) q; RM-091 board 4 Ferrite core 2 Sheet 7 FK-088 board 6 Four screws (M2 × 3), spring bolt 2 Four tapping screws (B2 × 5) qs FP-897 flexible board (21P) 6 XZ-003 board 8 Two claws 9 RM fixed holder assembly 3 Tapping screw (B2 × 5) qa Screw (M2 × 3), lock ace
9 Cabinet (upper) 5 Three screws (M2 × 5), spring bolt 8 FK frame assembly
qd MA-430D board
7 Screw (M2.6) 8 Cable holder 6 Four screws (M2.6) 3 Three screws (M2 × 5), lock ace
Remove the XM-005 board and XLR sheet metal in the direction of the arrow.
9 5 Two FP-217 flexible boards (16P) 0 XM-005 board, XLR sheet metal A
w; Handle (D) assembly
qa Handle cabinet (R) 1 Two screws (B3 ×10) qd Screw (M2 × 3), lock ace qs FP-218 flexible board (13P) A 2 Microphone holder assembly qf XD-003 board, DD bracket 4 Two screws (M2 × 5), lock ace
qj SW insulated plate qh Two tapping screws (B2 × 5)
ql Handle cabinet (L) assembly
qg Three Tapping screws (M2 × 5) qk XS-004 board, FP-897 flexible board
When installing it, align the five switch positions as arrow.
PRECAUTION DURING INSTALLATION
2-5
DSR-PD170/PD170P/PD190P
[FK-088, MA-430D, RM-091, XD-003, XS-004, XM-005 BOARDS SERVICE POSITION]
MA-430D board FP-217 flexible board (16P) XM-005 board FP-218 flexible board (13P) XD-003 board XS-004 board CPC-13 jig (J-6082-443-A) FP-897 flexible board (21P) XZ-003 board RM-091 board
FK-088 board Adjustment remote commander (RM-95) AC POWER ADAPTOR LANC jack AC IN
2-6
DSR-PD170/PD170P/PD190P
2-5. CABINET (L) BLOCK ASSEMBLY, MECHANISM DECK, VC-358D, DD-216D, JK-267 BOARDS (FOR FORCE EJECT OF CASSETTE AND VTR SECTION CHECK)
3 Screw (M2 × 5), spring bolt 6 Cabinet (L) block assembly
(FOR FORCE EJECT OF CASSETTE)
4 Screw (M2 × 3), lock ace 5 Flexible retainer 2 FP-895 flexible board (13P) 1 FP-193 flexible board (27P) q; Claw 8 JK-267 board (40P)
1 Screw (M2 × 5), lock ace 2 Screw (M2 × 5), lock ace 5 Three screws (M2 × 5), lock ace 4 Two screws (M2 × 3), lock ace
3 Screw (M2 × 3), lock ace 6 FP-187 flexible board (50P)
9 Four screws (M2 × 3), EG grip 7 FP-186 flexible board (80P) qa CD-512 board (50P)
qd DC-IN connector (3P) qs Battery terminal board (4P)
qf Mechanism deck, VC-358D, DD-216D board, MD frame assembly
(FOR VTR SECTION CHECK)
6 Mechanism deck, VC-358D board, MD frame assembly 4 FP-191 flexible board (60P)
5 -3 VCard o B 8D
1 Two screws (M2 × 5), spring bolt
DD D 6 21
3 Two screws (M2 × 3), lock ace
2 JK-267 board, JK frame
5 DD-216D board
2-7
DSR-PD170/PD170P/PD190P
[MECHANISM DECK SERVICE POSITION-1]
Note: Use the parts only which can be removed easily from outside of the mechanism deck.
Adjustment remote commander (RM-95)
Mechanism deck
CPC-13 jig (J-6082-443-A)
AC POWER ADAPTOR
AC IN
Cabinet (L) block assembly
[SERVICE POSITION TO CHECK THE VTR SECTION]
Connection to Check the VTR Section
To check the VTR Section, set the VTR to the "forced VTR power ON" mode. Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position) (However, connect the cabinet (L) assembly when cassette is going to be ejected only.) Setting the "Forced VTR Power ON" mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 02, and press the PAUSE button of the adjustment remote commander. Exiting the "Forced VTR Power ON" mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00.
AC IN
AC POWER ADAPTOR
DD-216D board DC-IN connector (3P) (1-794-637-11)
FP-191 flexible board (60P) Insert the FP-191 flexible board in the opposite direction to the normal insertion direction.
CPC-13 jig (J-6082-443-A) Connect here when the tape path check is going to be performed.
V B Co 3 a 5 rd 8 D
VC-358D board
JK-267 board
Mechanism deck
LANC jack
VIDEO jack
Monitor TV
Cabinet (L) block assembly
Adjustment remote commander (RM-95) Control switch block (CF-4980) (14P) (Connect here when cassette is going to be ejected.)
2-8
DSR-PD170/PD170P/PD190P
2-6. CABINET (R) BLOCK ASSEMBLY
5 Screw (M2 × 5), spring bolt
7 Cabinet (R) block assembly 6 Two screws (M2 × 5), lock ace 1 Screw (M2 × 5), spring bolt
4 Two screws (M2 × 5), spring bolt
3 CF ornamental plate 2 Claw
[CK-140 BOARD SERVICE POSITION]
CPC-13 jig (J-6082-443-A)
Adjustment remote commander (RM-95) AC POWER ADAPTOR LANC jack
C Bo K-1 ar 40 d
AC IN
CK-140 board Cabinet (R) block assembly
2-7. CABINET BOTTOM ASSEMBLY
REMOVING THE FBS COVER
1 Two tapping screws (B2 × 5) 3 Two tapping screws (B2 × 5)
1 FP-189 flexible board (6P)
5 Cabinet bottom assembly
2 FP-189 flexible board
5 FBS cover
3 Tripod table
4 Two screws (M2 × 5), lock ace 2 Four screws (M2 × 5), lock ace
4 Cabinet (bottom)
2-9
DSR-PD170/PD170P/PD190P
2-8. BATTERY PANEL BLOCK ASSEMBLY (MK-016, KP-013, MS-209 BOARDS)
9 CPC cover q; Battery panel block assembly 8 Screw (M2 × 5), lock ace 7 Two screws (M2 × 5), lock ace 6 Two screws (M2 × 5), lock ace
4 Screw (M2 × 3), lock ace
2 -0 LAard o b 8
1 FP-190 flexible board (20P) 5 Screw (M2 × 5), lock ace 2 DC-IN connector (3P) 3 Battery terminal board (4P)
qs DC-IN connector qa DC jack retainer q; Two tapping screws (B2 × 5) 9 MS holder assembly 8 Two tapping screws (B2 × 5) A
PRECAUTION DURING INSTALLATION
When installing it, align the switch position as shown.
09 -2 MS rd oa B
3 MK-016 board 2 MK retainer A 1 Two tapping screws (B2 × 5) 5 KP-013 board 4 Screw (M2 × 3), lock ace
7 MS-209 board
6 Two screws (M2 × 3), lock ace
2-9. EVF BLOCK ASSEMBLY
6 Two screws (M2 × 3), lock ace 1 FP-193 flexible board (27P) 7 EVF block assembly
4 Peel off the area shown by shading. 3 Claw 2 Screw (M2 × 3), lock ace 5 Flexible clamp
2 -0 LAard bo
8
2-10
DSR-PD170/PD170P/PD190P
2-10.LA-028, DD-216D, VC-358D, JK-267 BOARDS, MECHANISM DECK
1 Screw (M2 × 3), lock ace 2 Flexible retainer 9 LA joint 3 FP-188 flexible board (6P) 7 LA-028 board
28 -0 LA rd a Bo
8 Screw (M2 × 3), lock ace
6 Three screws (M2 × 3), lock ace
5 Flexible board (27P) (from VAP assembly) 4 Flexible board (39P) (from zoom lens assembly)
1 CD-512 board (50P)
8 -02 LABoard
4 Two screws (M2 × 5), spring bolt 5 3 Two screws (M2 × 3), EG grip 2 Two screws (M2 × 3), EG grip
8 Two screws (M2 × 2), lock ace
9 LD outer lid 7 MD frame assembly
4 VC-358D board q; Mechanism deck A CB D 5 Two step screws (M2) DB qa Two screws C (M2 × 3), lock ace A 3 Three screws (M2 × 3), lock ace 1 Two screws (M2 × 3), lock ace
6 Step screw (M2) qg JK-267 board qs Two screws (M2 × 3), lock ace qd Two claws
58 -3 VCard Bo
D
DD D 6 21
(LA-028 board)
2 -0 LAard Bo 8
2 DD-216D board
qf JK frame
2-11
DSR-PD170/PD170P/PD190P
2-11.LENS BLOCK ASSEMBLY, CENTER FRAME (D) ASSEMBLY
qd Center frame (D) assembly 6 Screw (M2 × 3), lock ace qs FP-188 flexible board (6P) q; Two screws (M2 × 4), lock ace qa Two screws (M2 × 3), lock ace
9 Lens block assembly PRECAUTION DURING INSTALLATION
When installing it. Align the swich position. FP-188 flexible board
8 Two screws (M2 × 5), EG grip 7 Two screws (M2 × 5), EG grip 2 Tapping screw (B2 × 5) 1 Screw (M2 × 3), lock ace 3 CCD cover
Lens block assembly
Center frame (D) assembly
4 Screw (M2 × 3), lock ace 5 CJ-064 harness
[SERVICE POSITION TO CHECK THE CAMERA SECTION]
Connection to Check the CAMERA Section
To check the CAMERA Section, set the CAMERA to the "forced CAMERA power ON" mode. Setting the "Forced CAMERA Power ON" mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press the PAUSE button of the adjustment remote commander. Exiting the "Forced CAMERA Power ON" mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00.
FP-191 flexible board (60P) Insert the FP-191 flexible board in the opposite direction to the normal insertion direction. AC IN AC POWER ADAPTOR DD-216D board
FP-186 flexible board (80P) Insert the FP-186 flexible board in the opposite direction to the normal insertion direction. CD-512 board (50P) Flexible board (27P) (from VAP assembly)
8 2 -0 d A r L oa B
DC-IN connector (3P) (1-794-637-21) Extension cable (J-6082-496-A) (50P)
LA-028 board VC-358D board JK-267 board Lens block assembly
D V B Co 3 a 5 rd 8
Flexible board (39P) (from zoom lens assembly) Mechanism deck Monitor TV LANC jack VIDEO jack
Adjustment remote commander (RM-95)
2-12
DSR-PD170/PD170P/PD190P
2-12.CD-512, SE-147 BOARDS, ZOOM LENS ASSEMBLY
4 Three tapping screws (B2 × 5) 5 SE-147 board 3 Flexible board (6P) (from zoom lens assembly) 9 Zoom lens (VCL-6012WB) 1 Three tapping screws (M1.7 × 7)
2 (CCD) flexible block assembly
REMOVING THE CD-512 BOARD
8 Remove the soldering. 7 Sheet (CD) 9 CJ-064 harness 3 Remove the sixteen solderings. q; CD-512 board 4 Remove the sixteen solderings. 5 Remove the sixteen solderings. 2 Prism cover 1 CCD heat sink
6 CCD emblem 7 Rubber foot (A) 8 Name ring 6 Prism assembly
REMOVING THE ZOOM LENS ASSEMBLY
4 Ornamental ring assembly Rotate it in the direction of the arrow C and remove it in the direction of the arrow D. B A 3 Zoom lens assembly Rotate it in the direction of the arrow A and remove it in the direction of the arrow B. 1 Tapping screw (M1.7 × 4) 5 VAP assembly
2 Two tapping screws (B2 × 7)
C D
2-13.CONTROL SWITCH BLOCK (PS-4980), CONTROL SWITCH BLOCK (CF-4980)
5 Control switch block (PS-4980) 3 Control switch block (CF-4980) 1 Tapping screw (B2 × 5) 4 Two tapping screws (B2 × 5) 2 Control switch block (PS-4980) (8P) 7 Four tapping screws (B2 × 5) 8 Slider assembly PRECAUTION DURING INSTALLATION Install the slider assembly while pushing the eject lever fully to the left (CCW). 6 Push the eject knob in the direction of the arrow, and open the cassette lid.
Cassette lid Eject knob
q; Control switch block (CF-4980) Be careful not to damage the control switch block's (CF-4980) flexible.
9 Two tapping screws (B2 × 5)
Eject lever
2-13
DSR-PD170/PD170P/PD190P
[CONNECTION DIAGRAM FOR SERVICE POSITION (Mainly for voltage measurement and check)] CK-140, VC-358D, JK-267, CD-512, DD-216D, LA-028, KP-013, MK-016, MS-209 BOARDS, MECHANISM DECK-2
AC IN CPC-13 jig (J-6082-443-A) KP-013 board MK-016 board AC POWER ADAPTOR DC-IN connector (3P) (1-794-637-21) Battery panel assembly
Battery terminal board (4P) DD-216D board
B A
Mechanism deck
A B
MS-209 board Control switch block (PS-4980) (8P) LA-028 board
LA Bo-02 ar 8 d
Flexible board (27P) (from VAP assembly) Flexible board (39P) from zoom lens assembly
Control switch block (CF-4980) (14P) JK-267 board EVF block assembly Adjustment remote commander (RM-95) FP-193 flexible board (27P) CK-140 board Cabinet (R) block assembly VC-358D board FP-187 flexible board (50P) Lens block assembly CD-512 board (50P) Extension cable (J-6082-496-A) (50P)
2-14.CK-140 BOARD
PRECAUTION DURING INSTALLATION
V B Co 3 a 5 rd 8 D
When installing it. Align the switch position.
qa Claw 9 FP-194 flexible board (5P) qf CK-140 board
q; Seven screws (M2 × 3), lock ace
qd Harness (CP-094) (14P) qs Harness (CP-093) (8P) 3 R flexible protection sheet 5 Two screws (M2 × 3), lock ace 6 SP retainer plate assembly 2 FP-197 flexible board (6P) 1 Control switch block (ED-4980) (6P) 8 Speaker holder 4 Speaker (2P) 7 Speaker
2-14
DSR-PD170/PD170P/PD190P
2-15.CONTROL SWITCH BLOCK (ED-4980), HINGE ASSEMBLY
Start the removal work after the LCD section has been removed referring section 2-1.
2 Control switch block (ED-4980) 1 Bright button
3 Blind door (D) assembly 2 Hinge lid 1 Three screws (M2 × 3), lock ace 8 Three screws (M2 × 5), spring bolt 9
q; Screw (M1.7 × 2.5), lock ace qs Hinge assembly A
2 Screw (M1.7 × 2.5), 3 Three claws lock ace
4 Hinge cover (rear) 6 Two harness fixed tapes
7 6 Three screws (M2 × 3), spring bolt 4 Harness (CP-093) (8P) 5 Harness (CP-094) (14P)
qa FP-197 flexible board 9 Screw (M1.7 × 2.5), lock ace 5 Hinge cover (front)
A
1 Two screws (M1.7 × 2.5), lock ace
7 Harness (CP-093)
8 Harness (CP-094)
2-15
DSR-PD170/PD170P/PD190P
2-16.CIRCUIT BOARDS LOCATION
The circuit boards contained in the zoom lens are not shown.
XD-003 DC/DC CONVERTER, REMOTE COMMANDER RECEIVER MA-430D (AUDIO AMP) XM-005 (MIC AMP)
LB-100D (BACK LIGHT)
CK-140 (KEY IN)
PD-217 (RGB DRIVE, TG)
XS-004 (MIC SELECT)
INVERTER TRANSFORMER UNIT HL-013 (LCD DRIVE) CD-512 (CCD IMAGER) FK-088 (CONTROL SWITCH)
SE-147 (VAP SENSOR)
RM-091 (REAR REMOTE COMMANDER RECEIVER) XZ-003 (LITHIUM BATTERY, SW) JK-267 (JACK BOARD)
LA-028 ZOOM/FOCUS DRIVE, VAP DRIVE, KEY IN/CONNECTOR
MK-016 (CONTROL KEY)
KP-013 (SELECT DIAL) MS-209 (MS CONNECTOR)
DD-216D (DC/DC CONVERTER, DC REGULATOR) VC-358D S/H AGC, TG, CAMERA SIGNAL PROCESS, MS I/F, RS232C I/F, STILL CONTROL, MS DRIVE, DV SIGNAL PROCESS, DV INTERFACE, REC/PB AMP, LINE IN/OUT, LINE A/D, RGB DRIVE/TG, CAMERA CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, HI CONTROL, AU LINE A/D, D/A, LINE AMP, CONNECTOR
2-16
DSR-PD170/PD170P/PD190P
2-17.FLEXIBLE BOARDS LOCATION
The flexible boards contained in the mechanism deck and that in the zoom lens are not shown.
FP-193 FP-897 FP-202 FP-895
FP-194 FP-190
FP-196 FP-189 FP-195 FP-191 FP-188 CONTROL SWITCH BLOCK (ED-4980)
CONTROL SWITCH BLOCK (PS-4980)
FP-186
FP-187 FP-218 FP-217 FP-205
FP-197
CONTROL SWITCH BLOCK (CF-4980)
2-17E
DSR-PD170/PD170P/PD190P
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/4) OVERALL BLOCK DIAGRAM (2/4) OVERALL BLOCK DIAGRAM (3/4) OVERALL BLOCK DIAGRAM (4/4) POWER BLOCK DIAGRAM (1/3) POWER BLOCK DIAGRAM (2/3) POWER BLOCK DIAGRAM (3/3)
DSR-PD170/PD170P/PD190P SECTION 3 BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/4)
CD-512 BOARD IC103 IC101
G-CH CCD IMAGER 8 3 1 35 35 31 32 11,14-16 1-4 V1,V2A,V2B,V3 40 40 43 43 44 44 H1,H2,RG,SUB 29 47 47 DICHROIC PRISM 5 R 21 CN025 G CCD OUT 40 42 1 3 G 38 47 G D0-09 2 11
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-358D BOARD(1/4)
AGC CONT 1,2 R,B GAIN R,G,B OFFSET
(1/18)
7
19
(1/18)
(2/18)
(IC705)SPCK 38 Y0-Y7 45
IC704
S/H,AGC 28
IC706
A/D CONVERTER 26 36 R D0-09 79 88
IC771
CAMERA SIGNAL PROCESS
LENS BLOCK
29 C0-C7 36 49 HD,VD,OE
1
TO OVERALL BLOCK DIAGRAM (2/4)
IC104 IC102
R-CH CCD IMAGER 8 R CCD OUT 3 1 19 19
IRIS
11 35 34 B 1 48 26 25 19 28 28 29 29 H1,H2,RG,SUB 32 32 XSHD XSHP XRS 11 14 37 38 44 CLPDM PBLK CLP OB 48 1 2 14
B D0-09
50 99 51 90 HI SO,SI,SCK
(PAGE 3-3)
9
17
11,14-16
1-4 V1,V2A,V2B,V3
25 25
IC105 IC100
B-CH CCD IMAGER 8 B CCD OUT 3 1 9 9 31 X701 27MHz H1,H2,RG 6 H1,H2,RG,SUB 18 18 SUB CN100 V1,V2A,V2B,V3 6 45 13 13 29 46 71 HD,VD 70 32 11,14-16 1-4 V1,V2A,V2B,V3 17 3 3
IC705
TIMING GENERATOR 47 SPCK 47 77
(1/18)
IC701,702
CCD V DRIVE
10 5 9
39 38
IRIS METER
(1/3)
DRIVE20 8 IRIS DRIVE 10 HALL AD HALL AMP 5 ZM RST SENS 22 1 7 41 42
(1/18)
IRIS PWM 54 53
M H
ZOOM RESET SENSOR
IC141
HALL17
EN1 DIR 1A,1B 61 62 64 66 68 AGC CONT 1,2 R,B GAIN R,G,B OFFSET EN1 DIR 1A,1B
62 63 64
ZOOM MOTOR
M M
2 4 6 34
ZOOM A,B
(1/3)
ZOOM MOTOR DRIVE
63 65 67
EN0 DIR 0A,0B
59 60 61
IC140
FOCUS A,B FOCUS MOTOR DRIVE
IC803
ZM RST SENS EVR 17 16 FC RST SENS
58 57
64 FOCUS MOTOR 36 38 39 FC RST SENS FOCUS RESET SENSOR 25 28 ND A,B,C ND FILTER SW 27 29 CN050 ACTIVE PRISM ACTUATOR 55 57 59 53 66 68
63 65 67 60 54 56 58
EN0 DIR 0A,0B
43 66 19 20 17 18 82
(12/18)
IC802
CAMERA CONTROL 33 CAM SO,SI,SCK 35
(12/18)
14 15 66
(2/3)
4
3
2
P Y
21 20
P DRIV A,B
IC070,071 073-076
ACTIVE PRISM ACTUATOR DRIVE
P PWM 56 55
45 64 63 ZM SPD SEL
IC801
EEPROM H ZOOM AD
15 14
Y DRIV A,B
Y PWM 58 57
44 48 HI SO,SI,SCK
(12/18)
50 62 ZOOM VR AD ZM SPD SEL H ZOOM AD ZOOM VR AD
2
TO OVERALL BLOCK DIAGRAM (4/4)
P OUT 12 Y OUT 22 46 45 44 43
61 60
(2/3)
25 VAP LOCK 26 VAP LOCK DRIVE VAP LOCK +,-
(PAGE3-7)
VP LOCK DR 36 35 7
IC072
VP LOCK SENS 23 38 37
10
(1/3)
ZOOM RING 3 5 MZ F0,F1 1,2 DETECTOR
XM-005 BOARD
CN200 48 47 49 MZ A,B 24 25 INPUT 1 50
IC144
8,13
XS-004 BOARD (1/2) IC202
2 7 LOW CUT AMP 5 CN201 14 3 CN102 1 21
MIC L (1/3)
FOCUS RING 8 9 CN052 MF F0,F1 1,2 DETECTOR
IC200 IC201
MIC/LINE AMP
MA-430D BOARD (1/2)
23
FK-088 BOARD (1/2)
39 27
LA-028 BOARD (2/4)
2 CH1 TO OVERALL BLOCK DIAGRAM (2/4) (VC-358D)
IC143
8,13
2 S103 CN103 INPUT1 INPUT SLECT SW S102 INPUT1 REC CH SELECT CH1
20 CN1106
22 CN500 CN501
40
26 CN053 CN051
1
CH2
3
47 49
48 50
MF A,B
22 23 1 11 40 X801 20MHz 41 16 6
(PAGE 3-3)
SE601 PITCH SENSOR SE600 YAW SENSOR CN600 YSD OUT 3 10 8 CN050 PSD OUT 5 12 12
(2/3)
IC200
18 PITCH/YAW SENSOR AMP
PS OUT 43 44
59
MIC R
CN300
IC300 IC301
MIC/LINE AMP
IC302
2 7 LOW CUT AMP 5
CN301 14 3
CH1+CH2
XD-003 BOARD (1/2)
CN401 7 SHOE UNREG 8 7 6
YS OUT 45 2 CN051 CN023 46
58
INPUT 2 1 11 16 6 CN101
S104 INPUT2 INPUT SLECT SW
IC401
DC/DC CONV.
16
SE-147 BOARD
CH1 MIC 48V CH2 MIC 48V CN100
5 6
8 9
LA-028 BOARD(1/4)
AUDIO SIGNAL VIDEO SIGNAL
3-1
3-2
DSR-PD170/PD170P/PD190P
3. BLOCK DIAGRAMS
3-2. OVERALL BLOCK DIAGRAM (2/4)
VC-358D BOARD(2/4)
(3/18)
SPCK SPCK
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN300
DV Interface
(6/18)
199 77 203 | Y0-Y7 207 211 215 3 7 17 HD,VD OE 62 21 23 200 202 206 212 216 6 8 213 68 1 | C0-C3 5 64 63 DV SIGNAL PROCESS 205 201
138 139 142 | 145
IC1407
37 60 DIGITAL STILL PROCESS | 51
IC301
X301 24.576MHz
(7/18)
45 L BUS 42
CN006 6 9 TPA+,TPB+,6 2 6 2
CN301
70
IC361
DV INTERFACE
YO-Y7
Y0-Y7
1
CO-C7 TO OVERALL BLOCK DIAGRAM (1/4) C0-C7 HD,VD,OE HD,VD,DE
46 | 38 49 61 48 47 HI SO,SI,SCK 96
51 141 152 153 156 133 132 127
TRCK LCK
47 79
29 MC BUS 37
FRRV,TRRV,TRRT
JK-267 BOARD(1/2)
J301 S1 VIDEO
(PAGE 3-2)
JK-267 BOARD (2/2)
DATA TO SFD DATA FROM SFD SFD BCK
IC1301
39 48 42 LINE IN LINE OUT AGC ACC Y C
SPCK
68
IC903
A/D CONVERTER 59 Y0-Y7 52 49 C0-C7 42
204 | 87 214 86 | 83 80 HD,VD,OE 79 C4-C7 9 2 4 Y0-Y7 208
11 13 15 18 22
99 97
REC CK REC DT
36 34
2 6
C
Y
Y 20 20 C 22 22 17 17 X1301 13.5MHz
Y
18 26 IC1301 CK 25
83 78 24 | HD,VD,DE 88 7 82 AFCK SYSCLK(IC1401) AFCK(IC903) SPCK(IC705) 196 48 170 8 | 20 · 19 HD VD 184 · 183 179 81 79 6
AD DT 6
38 37
G
G
C V
14 22 28 30 46 7 Y C
36
5
PB CK ATF ERR TO OVERALL BLOCK DIAGRAM (3/4)
(9/18)
10 9
(10/18)
63 66
34
J300(1/2) V VIDEO
(7/18) (3/18)
20 | 31 1 129 13 D0-D15 | 111 38 48 A0-A8 97 | 106 CHARACTER GENERATOR 18 · 17 · 16 · 14 COL0 195 · | COL3 194 · 191 · 190
MC BUS FRRV,TRRV,TRRT
(PAGE 3-5)
IC1403
4
TO OVERALL BLOCK DIAGRAM (4/4) HI SO,SI,SCK 16Mbit DRAM SP+,OSD CS,SO,SCK PANEL R,G,B,EVF R,G,B,HD,VD LANC SIG
IC302
159 | 161 VSP SO,SI,SCK
PANEL G 75 73 PANEL R PANEL B HD,VD EVF G 67 65 63 Y 55 59 C EVF R EVF B
(PAGE 3-8)
1
3 OSD CS OSD SO OSD SCK
71 105 · 106
VSP SO,SCK
141 · 142
12 | 21 JID0-JID7
J303 LANC SIG/232C RD LANC 35 35 140 132 143 144 4 1
(16/18)
IC1003
J302 HP L 26 26 HP R (HEADPHONES) 28 28 Q1008,1004 CH1 J300(2/2) AUDIO CH2 CH2 CN301 9 9 CN006 CH1 CH2 CH1 51 17 CH2 16 9 46 25 CH1 2 7 0dbB -7odB ATT 8 5 3 12 2 DATA FROM SFD DATA TO SFD SFD BCK 109 DI,CI 1 2 SHUTTER SOUND 7 5 CH2 55 19 CH1 CH1 12 12 1 3 CH1 54 AUDIO I/O 64 2
(16/18)
IC1001
8 10
SP+,-
(16/18)
IC1002
(16/18)
VSP SO, SCK
IC1010
15
D/A CONV. A/D CONV.
HI SO,SI SCK
(4/18)
X1401 7.375MHz 77 79 54-52 19 21 2 4
IC1406
EEPROM
SPCK1(IC705)
6
(4/18)
(17/18)
(17/18)
IC1412
SYSCLK 88 27 34 JID0-JID7 13 41 JPEG 2,9-16 58-64
IC1092
CH1 TO OVERALL BLOCK DIAGRAM (1/4) (LA-028) 1 10 8 3
IC1008
1 CH1 58
IC1012
(17/18)
2 7 CH2 0dbB -7odB ATT 5
(3/18)
(4/18)
4
112
IC1401
DIGITAL STILL CONTROL
(5/18)
IC1005
EVR
14
IC1409
18
IC1408
16Mbit DRAM SYSCLK(IC1401) 1-13 38-48 28 36
3
ATT CH2 2 CN023 7 12 13 14 5 5 7
(17/18)
5-15
55-75
20-31
(PAGE 3-2)
VSP SO,SCK 15 KASHAON 10 | A0-A10 | 38 4
(5/18)
IC1410
MEMORY STICK I/F DIO SCLK BS 15 | CN023 31 30 33 31 30 33
MS-209 BOARD
CN051 18 20 17 CN056 6 8 5 CN776 CN775 4 8 2
MEMORY STICK SLOT
(17/18)
D0-D15
1 · 48 X1411 20MHz 2 4 XTAL OSC SCK |
53 CH2 49 60
IC1004
AUDIO CHZ INPUT
23 14 15
CH2
(5/18)
17 40
IC1411
13
16
LA-028 BOARD(3/4)
AUDIO SIGNAL VIDEO SIGNAL VIDEO/AUDIO SIGNAL
3-3
3-4
DSR-PD170/PD170P/PD190P
3. BLOCK DIAGRAMS
3-3. OVERALL BLOCK DIAGRAM (3/4)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN007 FOR ADJUSTMENTS 3 2 RF MON
C MECHA DECK
(8/18)
REC CK REC DT
VC-358D BOARD(3/4)
REC CK REC DT
SWP
IC102
40 42 REC/PB AMP 6 7 2 1 EVEN CN101 ODD 5 6 8 9 VIDEO HEAD
(8/18)
AD DT 6 AD DT 6 20 EQ A/D CONV. PLL 34 ATF ERR 22 24 31 15
42
PB Y OUT
27
IC101
5
TO OVERALL BLOCK DIAGRAM (2/4)
PB CK
PB CK
13
(PAGE 3-4)
95 60 78 | DRP SO,XDRP SCK SWP
SWP
MC BUS FRRV TRRT,TRRV
(13/18)
80
CN024 CAP FG CAP ON,CAP FWD 2,3 32 14,15 24 25
M902
I