Text preview for : SONY HDR-TG1, TG1E, TG3E SERVICE MANUAL LEVEL 2 VER 1.2 2008.09 REV-1 (9-852-295-33).pdf part of SONY HDR-TG1 SONY HDR-TG1, TG1E, TG3E.
DIGITAL HD VIDEO CAMERA RECORDER.
SERVICE MANUAL VERSION 1.2 2008.09 REVISION-1. PART#(9-852-295-33)
Back to : SONY HDR-TG1, TG1E, TG3E | Home
HDR-TG1/TG1E/TG3E
SERVICE MANUAL LEVEL 2
US Model
Ver. 1.2 2008.09 Canadian Model
Revision History AEP Model
UK Model
Revised-1 North European Model
Replace the previously issued
E Model
SERVICE MANUAL 9-852-295-31 Australian Model
with this manual. Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
Photo: HDR-TG1
Link
SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS
SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST
· Precaution on Replacing the VC-522 Board
The components identified by Les composants identifiés par une
mark 0 or dotted line with marque 0 sont critiques pour la
mark 0 are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.
DIGITAL HD VIDEO CAMERA RECORDER
2008I0500-1
HDR-TG1/TG1E/TG3E_L2 © 2008.9
9-852-295-32 Sony EMCS Co. Published by Kohda TEC
These specifications are extracted from instruction
manual of HDR-TG1E/TG3E.
ENGLISH JAPANESE
SPECIFICATIONS
System Input/Output connectors AC Adaptor AC-L200/L200B
Video compression format: AVCHD (HD)/ A/V Remote Connector: Component/video and Power requirements: AC 100 V - 240 V, 50/60 Hz
MPEG2 (SD)/JPEG (Still images) audio output jack Current consumption: 0.35 - 0.18 A
Audio compression format: Dolby Digital 2/5.1ch HDMI OUT jack: HDMI mini Connector Power consumption: 18 W
Dolby Digital 5.1 Creator Output voltage: DC 8.4 V*
Video signal: PAL color, CCIR standards LCD screen Operating temperature: 0 °C to + 40 °C (32 °F to
1080/50i specification 104 °F)
Recording format: Movie (HD): AVCHD 1080/ Image: 6.7 cm (2.7 type, aspect ratio 16:9) Storage temperature: -20 °C to + 60 °C (-4 °F to +
50i Total dot number: 211 200 (960 × 220) 140 °F)
Movie (SD): MPEG2-PS Dimensions (approx.): 48 × 29 × 81 mm
Still image: Exif Ver.2.2*1 General (1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
Image device: 3.6 mm (1/5 type) CMOS sensor Power requirements: DC 6.8 V/7.2 V (battery excluding the projecting parts
Recording pixels (still image, 4:3): pack) Mass (approx.): 170 g (6.0 oz) excluding the
Max. 4.0 mega (2 304 × 1 728) pixels*2 DC 8.4 V (AC Adaptor) power cord (mains lead)
Gross: Approx. 2 360 000 pixels Average power consumption: During camera
Effective (movie, 16:9): Approx. 1 430 000 * See the label on the AC Adaptor for other
recording using the LCD with normal
pixels brightness: specifications.
Effective (still image, 16:9): Approx. HD: 3.3 W
1 490 000 pixels SD: 2.7 W Rechargeable battery pack NP-FH50
Effective (still image, 4:3): Approx. 1 990 000 Operating temperature: 0 °C to + 40 °C (32 °F to Maximum output voltage: DC 8.4 V
pixels 104 °F) Output voltage: DC 6.8 V
Lens: Carl Zeiss Vario-Tessar Storage temperature: -20 °C to + 60 °C (-4 °F to + Capacity: 6.1 Wh (900 mAh)
10 × (Optical), 20 ×, 120 × (Digital) 140 °F) Type: Li-ion
Focal length: F1.8 ~ 2.3 Dimensions (approx.): 32 × 119 × 63 mm
f=3.2 ~ 32.0 mm (5/32 ~ 1 5/16 in.) (1 5/16 × 4 3/4 × 2 1/2 in.) (w/h/d) Design and specifications are subject to change
When converted to a 35 mm still camera including the projecting parts without notice.
For movies*3: 43 ~ 507 mm (1 3/4 ~ 20 in.) 32 × 119 × 63 mm · Manufactured under license from Dolby
(16:9) (1 5/16 × 4 3/4 × 2 1/2 in.) (w/h/d) Laboratories.
For still images: 38 ~ 380 mm (1 1/2 ~ 15 in.) including the projecting parts, and the supplied
(4:3) rechargeable battery pack attached
Color temperature: [AUTO], [ONE PUSH], Mass (approx.): 240 g (8 oz) main unit only
[INDOOR] (3 200 K), 300 g (10 oz) including the supplied
[OUTDOOR] (5 800 K) rechargeable battery pack, and a "Memory
Minimum illumination: 5 lx (lux) ([AUTO SLW Stick PRO Duo"
SHUTTR] [ON], Shutter speed 1/25 sec)
*1 "Exif" is a file format for still images, Handycam Station DCRA-C230
established by the JEITA (Japan
Electronics and Information Technology
Input/Output connectors
Industries Association). Files in this A/V OUT jack: Component/video and audio
format can have additional information output jack
such as your camcorder's setting USB jack: mini-B
information at the time of recording. (HDR-TG3E: output only)
*2 The unique pixel array of Sony's ClearVid
CMOS sensor and image processing
Dedicated USB Terminal Adaptor
system (BIONZ) allows still image Input/Output connectors
resolution equivalent to the sizes
described. USB jack: mini-B
(HDR-TG3E: output only)
*3 The focal length figures are actual figures
resulting from wide angle pixel readout.
HDR-TG1/TG1E/TG3E_L2
--2--
These specifications are extracted from instruction
manual of HDR-TG1.
ENGLISH JAPANESE
SPECIFICATIONS
System Input/Output connectors AC Adaptor AC-L200/L200B
Video compression format: AVCHD (HD)/ A/V Remote Connector: Component/video and Power requirements: AC 100 V - 240 V, 50/60 Hz
MPEG2 (SD)/JPEG (Still images) audio output jack Current consumption: 0.35 - 0.18 A
Audio compression format: Dolby Digital 2/5.1ch HDMI OUT jack: HDMI mini Connector Power consumption: 18 W
Dolby Digital 5.1 Creator Output voltage: DC 8.4 V*
Video signal: NTSC color, EIA standards LCD screen Operating temperature: 0 °C to + 40 °C (32 °F to
1080/60i specification 104 °F)
Recording format: Movie (HD): AVCHD 1080/ Image: 6.7 cm (2.7 type, aspect ratio 16:9) Storage temperature: -20 °C to + 60 °C (-4 °F to +
60i Total dot number: 211 200 (960 × 220) 140 °F)
Movie (SD): MPEG2-PS Dimensions (approx.): 48 × 29 × 81 mm
Still image: Exif Ver.2.2*1 General (1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
Image device: 3.6 mm (1/5 type) CMOS sensor Power requirements: DC 6.8 V/7.2 V (battery excluding the projecting parts
Recording pixels (still image, 4:3): pack) Mass (approx.): 170 g (6.0 oz) excluding the
Max. 4.0 mega (2 304 × 1 728) pixels*2 DC 8.4 V (AC Adaptor) power cord (mains lead)
Gross: Approx. 2 360 000 pixels Average power consumption: During camera
Effective (movie, 16:9): Approx. 1 430 000 * See the label on the AC Adaptor for other
recording using the LCD with normal
pixels brightness: specifications.
Effective (still image, 16:9): Approx. HD: 3.4 W
1 490 000 pixels SD: 2.7 W Rechargeable battery pack NP-FH50
Effective (still image, 4:3): Approx. 1 990 000 Operating temperature: 0 °C to + 40 °C (32 °F to
pixels Maximum output voltage: DC 8.4 V
104 °F) Output voltage: DC 6.8 V
Lens: Carl Zeiss Vario-Tessar Storage temperature: -20 °C to + 60 °C (-4 °F to +
10 × (Optical), 20 ×, 120 × (Digital) Capacity: 6.1 Wh (900 mAh)
140 °F) Type: Li-ion
Focal length: F1.8 ~ 2.3 Dimensions (approx.): 32 × 119 × 63 mm
f=3.2 ~ 32.0 mm (5/32 ~ 1 5/16 in.) (1 5/16 × 4 3/4 × 2 1/2 in.) (w/h/d) Design and specifications are subject to change
When converted to a 35 mm still camera including the projecting parts without notice.
For movies*3: 43 ~ 507 mm (1 3/4 ~ 20 in.) 32 × 119 × 63 mm
(16:9) · Manufactured under license from Dolby
(1 5/16 × 4 3/4 × 2 1/2 in.) (w/h/d) Laboratories.
For still images: 38 ~ 380 mm (1 1/2 ~ 15 in.) including the projecting parts, and the supplied
(4:3) rechargeable battery pack attached
Color temperature: [AUTO], [ONE PUSH], Mass (approx.): 240 g (8 oz) main unit only
[INDOOR] (3 200 K), 300 g (10 oz) including the supplied
[OUTDOOR] (5 800 K) rechargeable battery pack, and a "Memory
Minimum illumination: 5 lx (lux) ([AUTO SLW Stick PRO Duo"
SHUTTR] [ON], Shutter speed 1/30 sec)
*1 "Exif " is a file format for still images, Handycam Station DCRA-C230
established by the JEITA (Japan
Electronics and Information Technology Input/Output connectors
Industries Association). Files in this A/V OUT jack: Component/video and audio
format can have additional information output jack
such as your camcorder's setting USB jack: mini-B
information at the time of recording.
*2 The unique pixel array of Sony's ClearVid Dedicated USB Terminal Adaptor
CMOS sensor and image processing
system (BIONZ) allows still image Input/Output connectors
resolution equivalent to the sizes USB jack: mini-B
described.
*3 The focal length figures are actual figures
resulting from wide angle pixel readout.
HDR-TG1/TG1E/TG3E_L2
--3--
ENGLISH JAPANESE
AVCHD HD /MPEG2 SD /JPEG 6.8 V/7.2 V NP-FH50
DC 8.4 V
DC 8.4 V
Dolby Digital2/5.1ch DC 6.8 V
5.1 HD 3.4 W SD 2.7 W
6.1 Wh 900 mAh
NTSC EIA 0 +40
1080/60i Li-ion
20 +60
HD: AVCHD 1080/60i 32 119 63 mm
SD: MPEG2-PS
Exif Ver.2.2*1 32 119 63 mm
·
3.6 mm 1/5 CMOS
400 *2
2 304 1 728 4:3 240 g
236 300 g
16 9 143 PRO
16 9 149
4 3 199
DCRA-C230
10 20 120
F1.8 2.3 /
f=3.2 32.0 mm A/V OUT
35mm
*3 USB mini-B
43 507 mm 16:9
USB
38 380 4:3
/
3 200 K 5 800 K USB mini-B
5 lx
1/30 AC AC-L200/L200B
*1 JEITA AC 100 V-240 V 50/60 Hz
18 W
DC 8.4 V *
0 +40
*2 CMOS 20 +60
48 29 81 mm
BIONZ
170 g
*3
/ * AC
A/V
HDMI OUT HDMI
6.7 cm 2.7 16:9
211 200
960 220
HDR-TG1/TG1E/TG3E_L2
--4--
Model information table
Model HDR-TG1 HDR-TG1E HDR-TG3E
US, CND, E NE, E, AUS,
Destination AEP, UK, NE
KR, JE, J HK, CH, JE
Color system NTSC PAL PAL
Data CAM PC a a a
copy PC CAM a a ×
· Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-TG1/TG1E/TG3E_L2
--5--
ENGLISH JAPANESE
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
2. Check the interboard wiring to ensure that no wires are
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
: LEAD FREE MARK
transistors, that were installed during a previous repair. Point
Unleaded solder has the following characteristics.
them out to the customer and recommend their replacement. · Unleaded solder melts at a temperature about 40°C higher than
4. Look for parts which, through functioning, show obvious signs ordinary solder.
of deterioration. Point them out to the customer and Ordinary soldering irons can be used but the iron tip has to be
recommend their replacement. applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350°C.
· Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
· Strong viscosity
· Do not touch the soldering iron on the same conductor of the
Unleaded solder is more viscous (sticky, less prone to flow) than
circuit board (within 3 times). ordinary solder so use caution not to let solder bridges occur such
· Be careful not to apply force on the conductor when soldering as on IC pins, etc.
or unsoldering. · Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HDR-TG1/TG1E/TG3E_L2
--6--
ENGLISH JAPANESE
·
·
·
0
·
·
·
· ·
HDR-TG1/TG1E/TG3E_L2
--7--
1. SERVICE NOTE ENGLISH JAPANESE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200/L200B).
1-2. PRECAUTION ON REPLACING THE VC-522 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform "DESTINATION DATA WRITE".
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform "USB SERIAL No. INPUT".
1-3. SELF-DIAGNOSIS FUNCTION
1-3-1. Self-diagnosis Function 1-3-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the counter of the
function starts working, and displays on the viewfinder or LCD viewfinder or LCD screen shows a 4-digit display consisting of an
screen what to do. alphabet and numbers, which blinks at 3.2 Hz. This 5-character
Details of the self-diagnosis functions are provided in the Instruction display indicates the "repaired by:", "block" in which the problem
manual. occurred, and "detailed code" of the problem.
Viewfinder or LCD screen
C:31:11
Blinks at 3.2 Hz
C 31 11
Repaired by: Block Detailed Code
C : Corrected by customer Indicates the appropriate Refer to "1-3-3. Self-diagnosis Code Table".
H : Corrected by dealer step to be taken.
E : Corrected by service E.g.
engineer 31 ....Reload the tape.
32 ....Turn on power again.
HDR-TG1/TG1E/TG3E_L2
1-1
ENGLISH JAPANESE
1-3-3. Self-diagnosis Code Table
Self-diagnosis Code
Repaired by:
Block Detailed Symptom/State Correction
Function Code
C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.
"Memory Stick Duo" is unformatted. Format the "Memory Stick Duo".
C 1 3 0 1
"Memory Stick Duo" is broken. Insert a new "Memory Stick Duo".
Remove the power source.
C 1 3 0 2 Access error
Reconnect it again and operate your camcorder again.
Retry turn the power on by the power switch. If it does not
Difficult to adjust focus recover, check the focus MR sensor of lens block (pin 1, 2 of
C 3 2 6 0
(Cannot initialize focus) CN5202 on the LD-235 board). If it is OK, check the focus
motor drive IC (IC5201 on the LD-235 board).
E 2 0 0 0 Flash memory data are rewritten. Make flash memory data correct value. (Note 1)
Inspect the lens block zoom reset sensor (pin wf of CN5202 on
Zoom operations fault the LD-235 board) when zooming is performed when the zoom
E 6 1 1 0
(Cannot initialize zoom lens.) lever is operated, and the zoom motor drive circuit (IC5201 on
the LD-235 board) when zooming is not performed.
The abnormalities in initialization of
the focus lens and the abnormalities in
E 6 1 1 1 Check both C : 32 : 60 and E : 61 : 10 of the self-diagnosis code.
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
Inspect PITCH/YAW angular velocity sensors (SE6602 on the
E 6 2 0 0 work well. (With PITCH angular
SE-174 board) peripheral circuits.
velocity sensor output stopped.)
Handshake correction function does not
Inspect PITCH/YAW angular velocity sensors (SE6602 on the
E 6 2 0 1 work well. (With YAW angular velocity
SE-174 board) peripheral circuits.
sensor output stopped.)
E 9 1 0 1 Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit.
Fault of writing to or erasing the flash
E 9 4 0 0 Inspect the flash memory (IC2101 on the VC-522 board).
memory
Note 1: Refer to Service manual, ADJ ("1-3. DESTINATION DATA WRITE").
Note 2: When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
HDR-TG1/TG1E/TG3E_L2
1-2
ENGLISH JAPANESE
1-4. PRECAUTION ON REPLACING THE CABINET (L)
1-4-1. Precaution on ordering the Cabinet (L)
Note: After replacing the Cabinet (L), the serial number for it will
The model display adopts the laser printing method.
be changed to the one exclusive for service use.
Therefore, the Cabinet (L) for replacement differs depending on
Inform a customer of the serial number change and change
the destination.
the serial number in the repair data.
As similar displays are provided, choose the suitable one for order.
HDR-TG1 (J) HDR-TG1 (US) HDR-TG1 (CND)
Serial No. Serial No. Serial No.
Part No. Description Part No. Description Part No. Description
A-1542-400-A CABINET (L (TG1-J1)), A-1542-402-A CABINET (L (TG1-U2)), A-1542-403-A CABINET (L (TG1-CA2)),
SERVICE SERVICE SERVICE
HDR-TG1 (KR) HDR-TG1 (E, JE) HDR-TG1E (NE)
Serial No. Serial No. Serial No.
Part No. Description Part No. Description Part No. Description
A-1542-404-A CABINET (L (TG1-KR2)), A-1542-405-A CABINET (L (TG1-E23)), A-1542-406-A CABINET (L (TG1-CEL)),
SERVICE SERVICE SERVICE
HDR-TG1E (E, HK, AUS, JE) HDR-TG1E (CH) HDR-TG3E (NE)
Serial No. Serial No. Serial No.
Part No. Description Part No. Description Part No. Description
A-1542-407-A CABINET (L (E34)), A-1542-408-A CABINET (L (CN2)), A-1542-409-A CABINET (L (TG3-CEL)),
SERVICE SERVICE SERVICE
HDR-TG3E (AEP, UK)
Serial No.
Part No. Description
A-1542-410-A CABINET (L (TG3-CEN)),
SERVICE
HDR-TG1/TG1E/TG3E_L2
1-3
ENGLISH JAPANESE
1-4-2. Precaution on Replacing the Cabinet (L) for J Models
The year of manufacture on the labels should be the same as the previous Cabinet (L) (circled portions shown on the below).
Example: For the figure below, attach the "Made of 08 years" label.
* The replacement label and "inset (how to affix)" are supplied together with Cabinet (L) for service.
* Manufacturing year
* Affix the label
1-4-3. Precaution on Replacing the Cabinet (L) for US Models
The date of manufacture and the manufacturer on the labels should be the same as the previous Cabinet (L) (circled portions shown on the
below).
Example: For the figure below, attach the "8A" and "SKD" labels.
* The replacement labels and "inset (how to affix)" are supplied together with Cabinet (L) for service.
* Manufacturing year * Factory
* Affix the label
1-4-4. Precaution on Replacing the Cabinet (L) for KR Models
The date of manufacture on the labels should be the same as the previous Cabinet (L) (circled portions shown on the below).
Example: For the figure below, attach the "2008.2" label.
* The replacement label and "inset (how to affix)" are supplied together with Cabinet (L) for service.
* Manufacturing year
* Affix the label
HDR-TG1/TG1E/TG3E_L2
1-4
1. SERVICE NOTE ENGLISH JAPANESE
C:31:11
C 31 11
HDR-TG1/TG1E/TG3E_L2
1-5
ENGLISH JAPANESE
C 0 4 0 0
C 1 3 0 1
C 1 3 0 2
C 3 2 6 0 1 2
E 2 0 0 0
E 6 1 1 0
wf
E 6 1 1 1
E 6 2 0 0
E 6 2 0 1
E 9 1 0 1
E 9 4 0 0
HDR-TG1/TG1E/TG3E_L2
1-6
ENGLISH JAPANESE
HDR-TG1 (J ) HDR-TG1 (US ) HDR-TG1 (CND )
A-1542-400-A A-1542-402-A A-1542-403-A
HDR-TG1 (KR ) HDR-TG1 (E, JE ) HDR-TG1E (NE )
A-1542-404-A A-1542-405-A A-1542-406-A
HDR-TG1E (E, HK, AUS, JE ) HDR-TG1E (CH ) HDR-TG3E (NE )
A-1542-407-A A-1542-408-A A-1542-409-A
HDR-TG3E (AEP, UK )
A-1542-410-A
HDR-TG1/TG1E/TG3E_L2
1-7
ENGLISH JAPANESE
*
*
* *
*
*
*
HDR-TG1/TG1E/TG3E_L2
1-8E
2. DISASSEMBLY
NOTE FOR REPAIR
Cut and remove the part of gilt
· Make sure that the flat cable and flexible board are not cracked of bent at the terminal. which comes off at the point.
Do not insert the cable insufficiently nor crookedly. (Be careful or some
pieces of gilt may be left inside)
· When remove a connector, don't pull at wire of connector. It is possible that a wire is snapped.
· When installing a connector, don't press down at wire of connector.
It is possible that a wire is snapped.
DISCHARGING OF FP-914 FLEXIBLE BOARD'S CHARGING CAPACITOR (C001)
The charging capacitor (C001) of FP-914 flexible board is
charged up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
Preparing the Short Jig
capacitor is handled by hand. The electric shock is caused by To preparing the short jig, a small clip is attached to each end of
the charged voltage which is kept without discharging when the a resistor of 1 k /1 W (1-215-869-11).
main power of the unit is simply turned off. Therefore, the Wrap insulating tape fully around the leads of the resistor to
remaining voltage must be discharged as described below. prevent electrical shock.
1 k/1 W
Wrap insulating tape.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
R:1 k/1 W
(Part code: 1-215-869-11)
FP-914
Flexible Board
HDR-TG1/TG1E/TG3E_L2
2-1
2-1. IDENTIFYING PARTS Control Switch Block
(PS27500)
Top Cabinet
Inner (Top) Cabinet
Lens Block
CM-096 Board
FP-910 Flexible Board
LD-235 Board
Main Frame
FP-902 Flexible Board
Cabinet (L) FP-903 Flexible Board
FP-905 Flexible Board
FP-906 Flexible Board
FP-907 Flexible Board
FP-911 Flexible Board
FP-912 Flexible Board
FP-913 Flexible Board
FP-915 Flexible Board
FP-916 Flexible Board
FP-917 Flexible Board
MD-137 Board
MS-396 Board
SE-174 Board
ST-186 Board
VC-522 Board
LCD Panel Block
FP-909 Flexible Board
Cabinet (R) Block
Front Cabinet FP-904 Flexible Board
FP-908 Flexible Board
FP-914 Flexible Board
- DISASSEMBLY FLOW -
2-2-1. OVERALL SECTION 2-2-2. Front Cabinet Section 2-2-3. Main Frame Section-1
Cabinet (L) Front Cabinet FP-907 Flexible Board
Control Switch Block (PS27500) Flash Unit Cabinet (R) Block
Inner (Top) Cabinet MS-396 Board SE-174 Board
2-2-4. Main Frame Section-2 2-2-5. Cabinet (R) Section
ST-186 Board JK Holder Block
MD-137 Board Capacitor Block
Lens Block LCD Panel Block
HDR-TG1/TG1E/TG3E_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW HARDWARE LIST
2-2-1. OVERALL SECTION
Follow the disassembly in the numerical order given.
1 Cabinet (L) (1-1 to 1-5)
2 Control Switch Block (PS27500) (2-1 to 2-3)
3 Inner (Top) Cabinet (3-1 to 3-9)
2 Control Switch Block
(PS27500)
2-1
(#14)
3-3 2-3
3-2
(Boss)
3-8 (#14)
3-6 2-2
1 Cabinet (L)
1-5 (#2) 3-1 (#2)
1-2 (#2)
3-9
3-5 (Boss)
3-4 (#14)
1-4 3-7
(Open)
3 Inner (Top) Cabinet
1-3 (#2)
1-1
(Open)
Front Cabinet Section
(See Page 2-4)
HDR-TG1/TG1E/TG3E_L2
2-3
2-2-2. FRONT CABINET SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Front Cabinet (1-1 to 1-5)
2 Flash Unit (2-1 to 2-3)
3 MS-396 board (3-1 to 3-6)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
R:1 k/1 W
(Part code: 1-215-869-11)
2-1
2 Flash Unit
FP-914
Flexible Board
2-3
3-3 3-5
3-1 (#14)
2-2 (#14)
3 MS-396 Board 1-3 (#5)
3-6 (#3)
6
-39
3-2 MS
3-4
1-2 (#14)
1-5
1-1 (#14)
Main Frame Section-1
(See Page 2-5)
1-4 (Claw)
1 Front Cabinet
HDR-TG1/TG1E/TG3E_L2
2-4
2-2-3. MAIN FRAME SECTION-1
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 FP-907 Flexible Board (1-1 to 1-4)
2 Cabinet (R) Block (2-1 to 2-6)
3 SE-174 Board (3-1 to 3-9)
Main Frame Section-2
(See Page 2-6)
3 SE-174 Board
2-5 (#14)
3-6
(#3)
3-3 1-2
3-9 (#3) HELP 1
3-7
(Claw)
3-8 2-6
3-5 (#14) 3-4 (#14)
3-2 (#3)
(#14)
2-1
1-3 (#14)
2-4
(#14)
3-1
1-1
2-2
2 Cabinet (R) Block
(See Page 2-7)
1-4 2-3
(Claw)
1 FP-907 Flexible Board
HDR-TG1/TG1E/TG3E_L2
2-5
2-2-4. MAIN FRAME SECTION-2
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 ST-186 Board (1-1 to 1-4)
2 MD-137 Board (2-1 to 2-6)
3 Lens Block (3-1 to 3-3)
2-1
1 ST-186 Board
2-2 (#3) HELP 4
1-2 (#3)
1-3
(Claw)
7 1-1
MD
-13 3 Lens Block
1-4
2-3
(Claw)
2-6
HELP 3
2 MD-137 Board
3-1
3-2
2-5
2
-52
VC
2-4 (#3)
3-3
HELP 2
HDR-TG1/TG1E/TG3E_L2
2-6
2-2-5. CABINET (R) SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 JK Holder Block (1-1 to 1-5)
2 Capacitor Block (2-1 to 2-2)
3 LCD Panel Block (3-1 to 3-13)
3-11
3-10 (#14) 3-12 (#14)
3 LCD Panel Block
3-1 (#14) 3-2
1 JK Holder Block
1-1 3-3
(#14) 3-7
3-6
3-5
3-4 (#14)
1-3
(#2) 1-4
3-8
HELP 1
3-9
1-5
3-13
1-2 (#2)
2-2
2 Capacitor Block
(#2)
2-1
HDR-TG1/TG1E/TG3E_L2
2-7
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP 1: DC Jack Harness
Hook
DC Jack Harness
FP-914 Flexible Board
FP-908 Flexible Board
DC Jack Harness
BT Frame Hook
Terminal Retainer Hook
HELP 2: Radiation Sheet (A)/AG Copy Sheet HELP 3: FP-917 Flexible Board
Radiation Sheet (A) AG Copy Sheet
Apply the fold habit.
Valley fold
AG Copy Sheet
VC-522 Board
HDR-TG1/TG1E/TG3E_L2
HELP
HELP 4: The Method of Attachment of ST-186 Board
1 Apply folds to the FP-915 flexible board as shown in 4 Prepare the stand of about 20 mm in height, and
the figure below. set it as shown in the figure below.
2 Install the FP-915 flexible board to CN7503 of 5 Install the FP-915 flexible board to CN1112 of
ST-186 board. MD-137 board.
6 Insert the claw of ST-186 board in the main frame.
CN7503 of ST-186 Board (Side A) 7 Tighten the screw.
6 Claw
7 Screw
1 Fold ST-186 Board
2 FP-915 Flexible Board
5 FP-915 Flexible Board
1 Fold
3 Install the FP-912 flexible board to CN7501 of
ST-186 board.
CN7501 of ST-186 Board (Side B)
About 20 mm
3 FP-912 Flexible Board
4 Stand
CN1112 of MD-137 Board (Side A)
8 Install the FP-912 flexible board to CN1026 of
VC-522 board.
8 FP-912 Flexible Board
CN1026 of VC-522 Board (Side A)
HDR-TG1/TG1E/TG3E_L2
HELP
HELP 5: The Method of Attachment of FP-909 Flexible Board
1 Apply folds to the FP-909 flexible board as shown in 5 Install the hinge clamp to the FP-909 flexible board.
the figure below. 6 Install the hinge assy to the hinge clamp.
2 Stick adhesive tapes.
3 Match the position of the hole, and stick adhesive
tapes.
4 Paste the JN copy sheet.
5 Hinge clamp
1 Mountain fold 2 Adhesive tape
6 Hinge assy
1 Mountain fold 1 Valley fold
7 Rotate the hinge assy.
2 Adhesive tape 8 Match the position of the boss, and stick adhesive
tapes.
9 Rotate the hinge clamp, and fix the FP-909 flexible
board.
1 Valley fold 7
8 Boss
3 Adhesive tape
9 Hinge clamp
0 Install the hinge cover (rear).
Note: Confirm the FP-909 flexible board is fixed.
qa Tighten the screw.
qa Screw 0 Hinge cover (rear)
Match the position
of the hole
4 JN Copy Sheet
HDR-TG1/TG1E/TG3E_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/7) OVERALL BLOCK DIAGRAM (6/7)
OVERALL BLOCK DIAGRAM (2/7) OVERALL BLOCK DIAGRAM (7/7)
OVERALL BLOCK DIAGRAM (3/7) POWER BLOCK DIAGRAM (1/3)
OVERALL BLOCK DIAGRAM (4/7) POWER BLOCK DIAGRAM (2/3)
OVERALL BLOCK DIAGRAM (5/7) POWER BLOCK DIAGRAM (3/3)
HDR-TG1/TG1E/TG3E_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/7) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LENS BLOCK CM-096 BOARD VC-522 BOARD (1/6)
IRIS
(SHUTTER) CN1303
CN6902
4M_DOAP/10M_DOCP, 4M_DOAP/10M_DOCP, SENS_DATA_P_5,
14, 16
14, 16
4M_DOAM/10M_DOCM 4M_DOAM/10M_DOCM SENS_DATA_M_5
K10,
K11
4M_DOBP/10M_DODP, 4M_DOBP/10M_DODP, SENS_DATA_P_4,
20, 22
20, 22
4M_DOBM/10M_DODM