Text preview for : SONY DSC-T100 SECTION 6 ADJUSTMENTS AUTO-ADJ VER 1.3 2007.05 (9-852-191-54)pdf.pdf part of SONY DSC-T100 SONY DSC-T100
DIGITAL STILL CAMERA.
SECTION 6 ADJUSTMENTS AUTO-ADJ VERSION 1.3 2007.05
PART#(9-852-191-54)
Back to : SONY DSC-T100 SECTION 6 A | Home
DSC-T100
Ver. 1.3 2007.05 SECTION 6 Auto-ADJ
Revision History ADJUSTMENTS
Link
Before starting adjustments SERVICE MODE
Adjusting items when replacing main parts and boards APPLICATION FOR ADJUSTMENT (SeusEX)
List of service tools SERVICE MODE
DATA BACKUP
CAMERA SECTION ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
ADJUSTMENT PROGRAM
DESTINATION DATA WRITE
USB SERIAL No. INPUT
VIDEO SYSTEM ADJUSTMENTS
CAMERA SYSTEM ADJUSTMENTS
LCD SYSTEM ADJUSTMENTS
ERROR
· Use this Service Manual together with the Automatic Adjustment Program (DSC-T100 Auto-Adj Ver_1.3r04.exe).
2007E0500-1
DSC-T100_ADJ © 2007.5
9-852-191-51 Sony EMCS Co. Published by Kohda TEC
TABLE OF CONTENTS
Section Title Page
6. ADJUSTMENTS
Before Starting Adjustments ····················································· 6-1
1-1. Adjusting Items When Replacing
Main Parts and Boards ···················································· 6-3
1-2. List of Service Tools ························································ 6-4
6-1. Camera Section Adjustments ··········································· 6-6
1-1. Preparations Before Adjustments ···································· 6-6
1-2. Adjustment Program ······················································ 6-13
1-3. Destination Data Write ·················································· 6-15
1-4. USB Serial No. Input ····················································· 6-16
1-5. Video System Adjustments ············································ 6-17
1-6. Camera System Adjustments ········································· 6-20
1-7. LCD System Adjustments ············································· 6-31
1-8. Error ··············································································· 6-33
6-2. Service Mode ································································· 6-35
2-1. Application for Adjustment (SeusEX) ·························· 6-35
2-2. Service Mode ································································· 6-36
2-3. Data Backup ·································································· 6-41
DSC-T100_ADJ
--2--
SECTION 6
ADJUSTMENTS
Before starting adjustments
Method for Copying or Erasing the Data in Internal Memory
(Internal Memory/Music)
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the
internal memory.)
Note 1: When replacing the SY-171 board, erase the data in internal memory of the board before replacement.
Note 2: When replacing the SY-171 board, execute formatting and initialize the internal memory after replace-
ment.
Method for copying the data in internal memory
Copy
Copies all images in the internal memory to a "Memory Stick Duo".
1 Insert a "Memory Stick Duo" having 32MB or larger capacity.
2 Select [Copy] with v/V/b/B on the control button, then press z.
The message "All data in internal memory will be copied" appears.
3 Select [OK] with v, then press z.
Copying starts.
To cancel the copying
Select [Cancel] in step 3, then press z.
· Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
· You cannot copy individual images.
· The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the "Memory Stick Duo" after copying, then execute the [Format] command in
[ Internal Memory Tool].
· When you copy the data in the internal memory to the "Memory Stick Duo", all the data will be copied.
You cannot choose a specific folder on the "Memory Stick Duo" as the destination for the data to be
copied.
· Even if you copy data, a DPOF (Print order) mark is not copied.
Method for formatting the internal memory
This item does not appear when a "Memory Stick Duo" is inserted in the camera.
Format
Formats the internal memory.
· Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1 Select [Format] with v/V/b/B on the control button, then press z.
The message "All data in internal memory will be erased" appears.
2 Select [OK] with v, then press z.
The format is complete.
To cancel the formatting
Select [Cancel] in step 2, then press z.
DSC-T100_ADJ
6-1
How to Write Data to Internal Memory
Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the
board replacement.
To change the setting, use the write enable tool "WriteEnableTool.exe".
Data writing method
1) Connect the PC to the camera (USB mode: Mass Storage), and switch the driver to the "Sony Seus USB Driver".
2) Start the Write Enable Tool and the SeusEX.
3) Click the [Activate Write Enable Mode] button of the Write Enable Tool.
4) Upon completion of the setting change, the following message will be displayed.
5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
6) Write the data read out into the PC to the internal memory of the camera.
7) Disconnect the PC from the camera, and turn off the camera.
Note: By turning off the camera, the write enable setting is reset.
DSC-T100_ADJ
6-2
1-1. Adjusting items when replacing main parts and boards
When replacing main parts and boards, adjust the items indicated by z in the following table.
Note 1: The automatic Adjustment Program does not support the "Wide Limit Adjustment". Perform it manually.
Note 2: When replacing the SY-171 board, erase the data in internal memory of the board before replacement.
Note 3: When replacing the SY-171 board, execute formatting and initialize the internal memory after replacement.
Replaced parts
Block Mounted parts Board
replacement replacement replacement
CCD block assy (Including CD-696 flexible board and CCD imager)
(Timing gen., CCD signal process)
(AF illumination LED)
SY-171 board SE502, SE501 (PITCH, YAW sensor)
(Video amp.)
SY-171 board (COMPLETE) (Note 2, 3)
LCD unit
Adjusting item Adjustment
(COMPLETE)
LCD901
SY-171 board IC304
SY-171 board IC602
D002
ST-162 board
ST-162 board
LCD block
Lens block
Flash unit
Destination Data Write Destination data write z
USB Serial No. Input USB serial No. input z
Composite video level adj. z z
Component out Y level adj.
VIDEO adjustment
Component out Pb level adj. z z
Component out Pr level adj.
CAMERA adjustment 1 Hall adj. z z
(Note 1) Wide limit adj. z z
CAMERA adjustment 2 Flange back adj. z z z
CAMERA adjustment 3 Flange back check z z z
F No. compensation
Measure gain adj.
Light value adj.
Mechanical shutter adj.
AWB 3200K-5800K standard data input
CAMERA adjustment 4 z z z z
AWB 3200K-5800K check
Color reproduction adj. & check
CCD linearity check
CCD white defect compensation check
CCD black defect compensation check
CAMERA adjustment 5 Strobe adj. z z z z z
CAMERA adjustment 6 Auto focus illumination check z z z
CAMERA adjustment 7 Angular velocity sensor sensitivity adj. z z z
V-COM adj.
LCD adjustment z z
White Balance adj.
Table 6-1-1
DSC-T100_ADJ
6-3
1-2. List of service tools
· Oscilloscope · Color monitor
J-1 J-2 J-3
HASP key and application
for adjustment (SeusEX)
Personal computer
(Note 1)
Contact our service headquater of each area USB, A/V, DC IN cable
how to get the application for adjustment for multi-use terminal
(SeusEX) and HASP key. 1-830-848-21
J-4 J-5 J-6
Pattern box PTB-450
9 colors chart (Note 2)
J-6082-200-A
USB cable or
1-829-868-41 For PTB-1450:
Small pattern box
J-6082-562-A
PTB-1450
J-6082-557-A
J-7 J-8 J-9
Clear chart
For PTB-450: Flange back
J-6080-621-A Minipattern box adjustment jig
J-6082-353-B J-6082-563-A
For PTB-1450:
J-6082-560-A
J-10 J-11 J-12
AC power adaptor
Siemens star chart Back ground paper
AC-LS5
J-6080-875-A J-2501-130-A
1-479-284-51
Fig. 6-1-1
Note 1: Personal computer
OS: Windows98/98SE/Me/2000/XP Home/XP Pro
RAM: 256 MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
Two connectors are required.
Note 2: In using the 9 colors chart on the pattern box PTB-450, adjust the chart size through the procedure shown below so that it matches
to the pattern box PTB-450.
1) Prepare a woody board A of the thickness 5 mm, and paint it mat-black.
2) Fit the 9 colors chart in the woody board A, and secure the chart with a black tape, etc. to shield the light.
woody boad A
woody boad A
360 mm
155 mm
135 mm 280 mm
9 colors chart
DSC-T100_ADJ
6-4
J-13 J-14 J-15
Tripod Adaptor
J-6082-577-A Camera table
J-6082-384-A HD Station (CSS-HD1)
(Note 3)
A-1242-190-A
Fig. 6-1-2
Note 3: The HD Station must be modified. (Refer to "4. HD Station Modifying Procedure")
DSC-T100_ADJ
6-5
6-1. CAMERA SECTION ADJUSTMENTS
1-1. PREPARATIONS BEFORE ADJUSTMENTS L = About 11 cm
1-1-1. Preparations Pattern box
1) Connect the equipment for adjustments according to Fig. 6-1-4. Front of the lens
2) Start up the application for adjustment (SeusEX).
L Camera
Fig. 6-1-3
· Connecting the Equipment
PC (The SeusEX must be installed in the PC.) DISP SEL switch setting
OS: Windows 98/98SE/Me/2000/XP
TV: Video/Camera
RAM: 256MB or more recommended
System Adjustment
USB: 2.0 recommended (also compatible with 1.1)
Two connectors are required. CAMERA: LCD
System Adjustment
To Multi connector
HASP Key
AC power adaptor
AC-LS5
To USB (1-479-284-51)
Video system Adjustment connector
(Composite video level adj.) AC IN
Osilloscope
USB, A/V, DC IN cable To DC IN jack
Color monitor for multi-use terminal
Terminated Video
75 (yellow) (1-830-848-21)
Audio
(Black)
Fig. 6-1-4
Note: The set must be connected to the modified HD station when performing the "Component out (Y, Pb, Pr) level adjustment" in the
"Video System Adjustment".
DSC-T100_ADJ
6-6
· Connection diagram when "Component out (Y, Pb, Pr) level adjustment in "Video System Adjustment" is performed.
Measurement Point (Component out (Y, Pb, Pr) level adj.)
Pr
Pb
Y
(COMPONENT OUT)
Y (Green)
Terminated Pr (Red)
75
Pb (Blue)
PC
OS: Windows 98/98SE/Me/2000/XP
RAM: 256MB or more recommended
USB: 2.0 recommended
To COMPONENT OUT (also compatible with 1.1)
Two connectors are required.
To DC IN jack
AC power adaptor
USB connector
AC IN
To USB USB cable
connector (1-829-868-41)
HASP Key
To USB
connector
Fig. 6-1-5
Note: For the USB connection, refer to "4. HD Station Modifying Procedure".
DSC-T100_ADJ
6-7
1-1-2. Precautions
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments.
1. HOME button (Shooting) ............................................ Auto Adjustment
2. ZOOM button ............................................................... WIDE end
3. Digital Zoom
(Setting - Shooting Settings - Shooting Settings 1) .... Off
9 colors chart (Standard picture frame)
A B A
A=B
C
B
C=
Green Yellow W14 3
C14: Filter for AWB 5800K adjustment
Cyan White Red B
C14 Blue Magenta
C
Adjust the camera position and direction
A to obtain the LCD screen or the monitor
Effective picture frame 2 Transparent window TV display shown in Fig. a.
Fig. a
( LCDmonitor TV under scan )
screen or
picture
Fig. 6-1-6
2. Subjects
1) 9 colors chart (Standard picture frame).
When performing adjustments using the 9 colors chart, adjust
the picture frame as shown in Fig. 6-1-6. (Standard picture
frame)
2) Clear chart (Standard picture frame)
Remove the 9 colors chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations dur-
ing this time)
DSC-T100_ADJ
6-8
3. Preparing the Flash Adjustment Box
A dark room is required to provide an accurate flash adjustment.
If it is not available, prepare the flash adjustment box as given
below;
1) Provide woody board A, B and C of 15 mm thickness.
woody board A (2) woody board B (2) woody board C (1)
400 mm 370 mm 700 mm
513 mm 513 mm 700 mm
730 mm 700 mm
Fig. 6-1-7
2) Apply black mat paint to one side of woody board A and B.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper
side of woody board A, B and C are internal. (Fig. 6-1-8)
woody board A
woody board B
woody board A
woody board B
woody board C
Fig. 6-1-8
L = 50cm
Flash adjustment box
Front of the lens
L Camera
Background paper
Fig. 6-1-9
DSC-T100_ADJ
6-9
4. HD Station Modifying Procedure
The HD station must be modified to perform the "Component out (Y, Pb, Pr) level adjustment" in the "Video System Adjustment".
Modify the HD station by the following steps.
1) Prepare the HD station and USB connector.
Part No.
HD station (Note) A-1242-190-A
USB connector 1-794-962-11
Note: You may purchase the commercially available CSS-HD1.
2) Disassemble the HD station in the numerical order given in the following figure to remove the Connector board.
1 Pull the switch
Upper cabinet
4 Lower cabinet
3 Five screws
6 Connector board/
5 Two screws Multi board
2 Two foot rubbers
Fig. 6-1-10
3) Mount the USB connector on the Connector board.
Connector board
Mount the USB connector.
Fig. 6-1-11
DSC-T100_ADJ
6-10
4) Connect four lead wires between USB connector and Multi board.
Wiring diagram when USB connector is added for modification
CN105 CN006
(USB connector) (No mount)
CONNECTOR BOARD (SIDE B)
VCC 1Pin 2Pin
D 2Pin 4Pin
D+ 3Pin 5Pin
GND 5Pin 6Pin CN105
2 4
1 3 5
MULTI BOARD (SIDE B)
1 5 21
CN006
22
2 4 6
Fig. 6-1-12
DSC-T100_ADJ
6-11
5) Puncture the Upper cabinet to make a window for the USB connector as shown below.
Upper cabinet
USB connector position
Puncture the Upper cabinet.
USB connector
Fig. 6-1-13
6) Assemble the HD station.
DSC-T100_ADJ
6-12
1-2. ADJUSTMENT PROGRAM 3. Function of Each Button on Main Menu Screen
The DSC-T100 is adjusted by the Automatic Adjustment Program. When the Automatic Adjustment Program started, the Main Menu
The Automatic Adjustment Program enters automatically via the screen in Fig. 6-1-14 will appear. On this screen, select each ad-
SeusEX the adjustment operations that were formerly entered justment section.
manually by the adjustment remote commander (some items may
be adjusted by manual operation on the operation screen of the
SeusEX).
1
1. Precautions When Using Automatic Adjustment
qa
Program
2
1) The Automatic Adjustment Program writes the adjustment re-
sults such as EVR data to the set through two-way communi- 4
cation with the camera via the SeusEX. Accordingly, the Au-
tomatic Adjustment Program must be used in the environment 5
where the SeusEX operates.
2) The Automatic Adjustment Program cannot be used when the 6
SeusEX or the SeusCam is running. Exit the SeusEX or the 9
SeusCam before using the Automatic Adjustment Program. 7
3) The SeusEX must be already started on the PC when using the 0
8
Automatic Adjustment Program. With the SeusEX not started,
some adjustment items will take time in adjustment. 3
4) The program run time may vary depending on the environ-
ment of the personal computer used. Fig. 6-1-14
2. Start of Automatic Adjustment Program 1 [Connecting the Equipment] button
Double-click the application file (DSC-T100 Auto-Adj A connection diagram of the equipment is displayed.
Ver_1.0r01.exe), and the Automatic Adjustment Program will start.
2 [CONNECT] button
The mode of Camcorder is switched to the Adjustment Mode.
When the Adjustment Mode has switched normally, the op-
eration of the buttons 4 - 0 is enabled.
3 [END] button
The mode of Camcorder is switched to the normal mode.
When the normal mode has switched correctly, the Automatic
Adjustment Program is finished.
4 [DESTINATION DATA WRITE] button
The "DESTINATION DATA WRITE" screen appears.
5 [USB SERIAL N0. INPUT] button
The "USB SERIAL No. INPUT" screen appears.
6 [VIDEO SYSTEM ADJUSTMENT] button
The "VIDEO SYSTEM ADJUSTMENT" screen appears.
7 [CAMERA SYSTEM ADJUSTMENT] button
The "CAMERA SYSTEM ADJUSTMENT" screen appears.
8 [LCD SYSTEM ADJUSTMENT] button
The "LCD SYSTEM ADJUSTMENT" screen appears.
9 [SERVICE MODE] button
The "SERVICE MODE" screen appears.
q; [DATA BACKUP] button
The "DATA BACKUP" screen appears.
qa This part indicates the version of Automatic Adjustment Pro-
gram.
DSC-T100_ADJ
6-13
4. Setting of Adjustment Mode 5. Release of Adjustment Mode
Before performing the adjustment, "Setting of Adjustment Mode" To finish the adjustment, be sure to perform "Release of Adjust-
is required. ment Mode".
[Setting method] [Releasing method]
1) Connect the Camera to the PC with a USB cable, and turn on 1) Click the [END] button on the Main Menu screen.
the power switch. 2) When the following message is displayed, releasing of adjust-
2) Start the Automatic Adjustment Program, and click the [Con- ment mode has completed. Click the [OK] button in the mes-
nect] button on the Main Menu screen. sage window to exit the Automatic Adjustment Program.
3) When the following message is displayed, turn off and on again Note: The Camera switches to the normal mode by turning
the power switch of the Camera. off and on the power switch. After the adjustment fin-
Note: Turning off and on the power switch causes the Cam- ished, turn off and on again the power switch of the
era to be switched to the Adjustment Mode. After the Camera to confirm that the USB mode screen is dis-
Camera restarted, click the [OK] button in the message played.
window.
4) Upon successful completion of the settings in the Adjustment
Mode, the operation of each button on the Main Menu screen
is enabled.
DSC-T100_ADJ
6-14
1-3. DESTINATION DATA WRITE 2. Destination Data Write
Note: The DESTINATION DATA WRITE cannot be set with other [Writing method]
than the Service board. 1) Select the written destination with the Destination List.
1. Function of Each Button on Destination Data Write
Screen
Click the [DESTINATION DATA WRITE] button on the Main Menu
screen, and the "DESTNATION DATA WRITE" screen in Fig. 6-
1-15 will appear.
1
3
2
2) Click the [Data Write] button.
Fig. 6-1-15
1 [To Menu] button
The Main Menu screen comes back.
2 Destination List
Selects the written destination.
3 [Data Write] button
Write the destination data to the camera. 3) The writing finishes when the following message is displayed.
SELECTABLE LANGUAGE
DSTINATION
VIDEO OUT
Default
Portuguese
Norwegian
Traditional
AREA
Hungarian
Simplified
Japanese
Swedish
Chinese
German
Spanish
Russian
Chinese
Persian
English
Turkish
Korean
Melayu
Finnish
French
Danish
Arabic
Czech
Polish
Greek
Italian
Dutch
Thai
J1 J z NTSC
JE3 JE z a a a a a a a a a PAL
U2 US z a a a a a NTSC
CA2 CND z a a a a a NTSC
CEE2 a a a a a a a z a a a a a a a a a PAL
CEE8 AEP z a a a a a a a a a a a a a a a a PAL
CEE9 z a a a a a a a a a a a a a a a a PAL
CEH UK z a a a a a a a a a a a a a a a a PAL
E15 z a a a a a a a a a PAL
E32 E z a a a a a a a a a PAL
E33 a z a a a a a a a a NTSC
AU2 AUS z a a a a a PAL
HK1 HK z a a a a a a a a a PAL
CN2 CH a a a z a a a a a a PAL
KR2 KR a a a a a z a a a a NTSC
BR1 BR a a z a a a a a a a NTSC
z: INITIAL LANGUAGE
Table 6-1-2
DSC-T100_ADJ
6-15
1-4. USB SERIAL No. INPUT 1. Function of Each Button on USB Serial No. Input
The set is shipped with a unique ID (USB Serial No.) written in it. Screen
This ID has not been written in a new board for service, and there- Click the [USB SERIAL No. INPUT] button on the Main Menu
fore it must be entered after the board replacement. screen, and "USB SERIAL No. INPUT" screen in Fig. 6-1-16
If original ID can be read from the board before replacement, read will appear.
it from the board before replacement using the "SERIAL READ/ 1
WRITE" screen, and then write it after replacement.
If original ID cannot be read from the board before replacement,
write the ID for service using the "MANUAL WRITE" screen.
(The ID for service is different from the ID written when the set is
shipped.) Enter the PRODUCT ID (last 5 characters of model name) 3
2
and SERIAL No. into the screen and write them.
4
5
6
7
Fig. 6-1-16
1 [To Menu] button
The Main menu screen comes back.
2 Display area
The "PRODUCT ID", "SERIAL No." and "ASCII TRANS-
LATION" are displayed.
For the "ASCII TRANSLATION", the last 5 characters of
model name are displayed if the PRODUCT ID is set from the
model name in the MANUAL WRITE. For the PRODUCT ID
set in the factory, the model name is not displayed but "?" etc.
will be displayed.
3 [Check Serial] button
The USB SERIAL No. data is read from the camera and dis-
played in the display area.
4 [Read and Save] button
The USB SERIAL No. data is read from the camera and saved
in PC as a file.
5 [Load and Write] button
The USB SERIAL No. data is loaded from the file saved in
PC and written to the camera.
6 Input area
Enter the "SERIAL No.".
For the "PRODUCT ID", the last 5 characters of model name
are fixed. For the "SERIAL No.", read it from the label on the
camera body and enter it.
7 [Write Manually] button
The USB SERIAL No. data entered in the input area is written
to the camera.
DSC-T100_ADJ
6-16
1-5. VIDEO SYSTEM ADJUSTMENTS
1-5-1. Function of Each Button on Video System
Adjustment Screen
Click the [VIDEO SYSTEM ADJUSTMENT] button on the Main
Menu screen, and the "VIDEO SYSTEM ADJUSTMENT"
screen in Fig. 6-1-17 will appear.
1
2 3
4
5
Fig. 6-1-17
1 [To Menu] button
The Main Menu screen comes back.
2 [Preparation] button
Notes for adjustment or jigs used are displayed.
3 [Start] button
Each adjustment "Composite Video Level Adjustment" or
"Component out (Y, Pb, Pr) Level Adjustment" starts.
4 [Reboot] button
When this button is clicked, the camera is rebooted.
5 [Release Data Setting] button
The data setting at the adjustment is cancelled.
During the data setting, the button color changes from "white"
to "red". When the data setting is cancelled, the button color
returns to "white".
(Use this button when an error occurred in the video adjust-
ment. If the adjustment completed successfully, the data set-
ting is automatically cancelled and the button color returns to
"white".)
1-5-2. Adjustment Items of VIDEO System Adjust-
ment
The adjustment items of video system adjustment are as listed in
Table 6-1-3. The Automatic Adjustment Program executes the ad-
justment items if the VIDEO Adjustment Start button is clicked.
Button Measuring Adjusting Address
Adjustment Measurement Point
Name Instrument Block Page Address
VIDEO terminal of USB, A/V, DC IN
Composite Video
cable for multi-USB terminal Oscilloscope 11 60 06DE
Level Adj.
(75 ohm terminated)
COMPONENT OUT
VIDEO R040 on Multi board (HD Station) Oscilloscope 11 60 06BF
Y Level Adj.
Adjustment
COMPONENT OUT
R041 on Multi board (HD Station) Oscilloscope 11 60 06C0
Pb Level Adj.
COMPONENT OUT
R042 on Multi board (HD Station) Oscilloscope 11 60 06C1
Pr Level Adj.
Table 6-1-3
DSC-T100_ADJ
6-17
1-5-3. Adjusting Method 4) If the [End] button is clicked, "4. VIDEO OUT Level Check"
1. Composite Video Level Adjustment will be executed. The following message and screen are dis-
[Automatic Adjustment Program execution items and played. Check that the sync signal level and burst level of the
sequence] video signals satisfies the specified value, and click the [OK]
1. Data Setting during Video Adj. button in the message.
2. Composite Video Level Adj.
3. VIDEO OUT Level Check
4. Release of Data Setting during Video Adj.
[Adjusting method]
1) Click the [Start] button of the Composite Video Level Adj.
2) The Automatic Adjustment Program executes the "1. Data
Setting during Video Adj.".
3) If "1. Data Setting during Video Adj." completed successfully,
the following screen is displayed during the execution of "2.
Composite Video Level Adj.". Using the [Up] / [Down] bu