Text preview for : SONY DSC-H1 SERVICE MANUAL LEVEL 2 VER 1.4 2006.06 (9-876-880-35).pdf part of SONY DSC-H1 SONY DSC-H1 DIGITAL STILL CAMERA. SERVICE MANUAL VERSION 1.4 2006.06 PART#(9-876-880-35)



Back to : SONY DSC-H1 SERVICE MANUA | Home

DSC-H1
SERVICE MANUAL
Ver. 1.4 2006. 06
Revision History How to use Acrobat Reader LEVEL

2

DSC-H1
US Model Canadian Model AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Japanese Model Korea Model Tourist Model

Internal memory ON BOARD

Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAMS SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST

· For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-880-51). · For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-880-41). · Reference number search on printed wiring boards is available. On the CH-169 and SY-127 board
This service manual provides the information that is premised the circuit board replacement service and not intended repair inside the SY-127 board. Therefore, schematic diagram, printed wiring board, mounted parts location and electrical parts list of the SY-127 board are not shown. The following pages are not shown. Schematic diagram ............................. Pages 4-21 to 4-44 Mounted parts location ............................. Page 4-64 Printed wiring board ............................ Pages 4-55 to 4-60 Electrical parts list ................................... Pages 5-14 to 5-18 Waveforms ........................................... Page 4-62

DIGITAL STILL CAMERA

DSC-H1
9-876-880-31

Sony EMCS Co.

2006F1600-1 ©2006.06 Published by Kohda TEC

SPECIFICATIONS

Camera
[System]
Image device 7.19 mm (1/2.5 type) color CCD, Primary color filter

[LCD screen]
LCD panel 6.2 cm (2.5 type) TFT drive Total number of dots 115 200 (480x240) dots

BC-CS2A/CS2B Ni-MH battery charger
Power requirements AC 100 to 240 V, 50/60 Hz, 3W Output voltage 0.75 cm (0.3 type) TFT drive AA: DC 1.4V 400 mAx2 AAA: DC 1.4 V 160 mAx2

Total pixel number of camera Approx. 5 255 000 pixels Effective pixel number of camera Approx. 5 127 000 pixels Lens 12 zoom lens f = 6.0 - 72.0 mm (36 - 432 mm when converted to a 35 mm still camera) F2.8 - 3.7

[Finder]
LCD panel Total number of dots 115 200 (480x240) dots

Operating temperature 0°C to +40°C (+32°F to +104°F) Storage temperature ­20°C to +60°C (­4°F to +140°F) Dimensions Approx. 71x30x91 mm (2 7/8x 13/16x 35/8 inches) (W/H/D) Approx. 90 g (3 oz)

[Power, general]
Power HR 15/51:HR6 (size AA) Nickel-Metal Hydride batteries (2), 2.4 V ZR6 (size AA) Oxy Nickel Primary Battery (2, not supplied), 3 V AC-LS5K AC Adaptor (not supplied), 4.2 V

Exposure control Automatic exposure, Shutter speed priority, Aperture priority, Manual exposure, Scene Selection (7 modes) White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash, One push

Mass

Power consumption (during shooting with the LCD screen) 1.8 W Operating temperature 0°C to +40°C (+32°F to +104°F) Storage temperature ­20°C to +60°C (­4°F to +140°F) Dimensions 108x81.4x91.2 mm (4 1/4x 31/4x 35/8 inches) (W/H/D, excluding maximum protrusions) Approx. 590.8 g (1 lb 20.8 oz) (including two batterries, shoulder strap, adaptor ring, lens hood, lens cap, etc.) Electret condenser microphone Dynamic speaker Compatible

Design and specifications are subject to change without notice.

File format (DCF compliant) Still images: Exif Ver. 2.2 JPEG compliant, DPOF compatible Movies: MPEG1 compliant (Monaural) Recording media Internal memory 32 MB "Memory Stick" Flash Recommended distance (ISO set to Auto): 0.3 m to 6.8 m (11 26/32 inches to 22 feet 3 23/32 inches) (W)/0.9 m to 5.2 m (2 feet 11 14/32 inches to 17 feet 23/32 inches) (T) Electric viewfinder (color)

Mass

Viewfinder

[Input and Output connectors]
A/V OUT (MONO) jack (Monaural) Minijack Video: 1 Vp-p, 75 , unbalanced, sync negative Audio: 327 mV (at a 47 k load) Output impedance 2.2 k USB jack mini-B Hi-Speed USB (USB 2.0 compliant) USB communication

Microphone Speaker Exif Print

PRINT Image Matching III Compatible PictBridge Compatible

DSC-H1

--2--

SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

2. 3.

4.

5. 6.

: LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

DSC-H1

--3--

1. 2.

TABLE OF CONTENTS 4-3. PRINTED WIRING BOARDS SERVICE NOTE ........................................................ 1-1 DISASSEMBLY
· CD-576 (CCD IMAGER) PRINTED WIRING BOARD ······················· 4-49 · MS-275 (MEMORY STICK, LI BATTERY) PRINTED WIRING BOARD ······················· 4-47 · ST-123 (FLASH DRIVE) PRINTED WIRING BOARD ······················· 4-51 · ST-124 (FLASH) PRINTED WIRING BOARD ······················· 4-52 · PL-039 (PLUNGER) PRINTED WIRING BOARD ······················· 4-51 · SW-447 (FUNCTION SW, PITCH/YAW SENSOR AMP) PRINTED WIRING BOARD ······················· 4-53 · EV-016 (EVF, BACK LIGHT) PRINTED WIRING BOARD ······················· 4-49 · AF-102 FLEXIBLE (AF LED, LENS COVER SW) PRINTED WIRING BOARD ······················· 4-47 Printed wiring board of the CH-169 and SY-127 board are not shown. Pages from 4-55 to 4-60 are not shown. 4-4. WAVEFORMS ······························································ 4-61 Waveforms of the SY-127 board are not shown. Page 4-62 is not shown. 4-5. MOUNTED PARTS LOCATION ································· 4-63 Mounted parts location of the SY-127 board is not shown. Page 4-64 is not shown.

2-1. DISASSEMBLY ······························································ 2-1 2-2. SERVICE POSITION ····················································· 2-5 2-3. CIRCUIT BOARDS LOCATION ··································· 2-7 2-4. FLEXIBLE BOARDS LOCATION ································ 2-8 HELP (List of caution points is shown here.)

3.
3-1. 3-2. 3-3. 3-4.

BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (1/2) ··························· 3-1 OVERALL BLOCK DIAGRAM (2/2) ··························· 3-3 POWER BLOCK DIAGRAM (1/2) ································ 3-5 POWER BLOCK DIAGRAM (2/2) ································ 3-7

4.

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM ································ 4-1 4-2. SCHEMATIC DIAGRAMS · CD-576 (CCD IMAGER) SCHEMATIC DIAGRAM ······························ 4-5 · MS-275 (MEMORY STICK, LI BATTERY) SCHEMATIC DIAGRAM ······························ 4-7 · ST-123 (FLASH DRIVE) SCHEMATIC DIAGRAM ······························ 4-9 · ST-124 (FLASH) SCHEMATIC DIAGRAM ···························· 4-17 · PL-039 (PLUNGER) SCHEMATIC DIAGRAM ······························ 4-8 · SW-447 (1/2) (FUNCTION SW) SCHEMATIC DIAGRAM ···························· 4-11 · SW-447 (2/2) (PITCH/YAW SENSOR AMP) SCHEMATIC DIAGRAM ···························· 4-13 · EV-016 (EVF, BACK LIGHT) SCHEMATIC DIAGRAM ······························ 4-7 · AF-102 FLEXIBLE (AF LED, LENS COVER SW) SCHEMATIC DIAGRAM ···························· 4-15 · SW-006 FLEXIBLE (SY-SW RELAY) SCHEMATIC DIAGRAM ···························· 4-18 · MS-029 FLEXIBLE (SY-MS RELAY) SCHEMATIC DIAGRAM ···························· 4-15 · ST-001 FLEXIBLE (SY-ST RELAY) SCHEMATIC DIAGRAM ···························· 4-17 · FP-224 FLEXIBLE (SY-CD RELAY) SCHEMATIC DIAGRAM ···························· 4-16 · CONTROL SWITCH BLOCK (SW51780) SCHEMATIC DIAGRAM ···························· 4-19 Shematic diagram of the CH-169 and SY-127 board are not shown. Pages from 4-21 to 4-44 are not shown.

5.

REPAIR PARTS LIST

5-1. EXPLODED VIEWS ······················································ 5-3 5-1-1. OVERALL SECTION ···················································· 5-3 5-1-2. LED SECTION, CABINET(REAR) SECTION ············ 5-4 5-1-3. MAIN SECTION ··························································· 5-5 5-1-4. EVF SECTON ······························································· 5-6 5-1-5. LENS SECTION ··························································· 5-7 5-1-6. CABINET(FRONT) SECTION ····································· 5-8 5-1-7. ST SECTION ································································· 5-9 Checking supplied accessories ················································ 5-10 5-2. ELECTRICAL PARTS LIST ········································ 5-11 Electrical parts list of the SY-127 board are not shown. Pages from 5-14 to 5-18 are not shown.

DSC-H1

--4--

1. SERVICE NOTE
· NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When remove a connector, don't pull at wire of connector. Be in danger of the snapping of a wire.

When installing a connector, don't press down at wire of connector. Be in danger of the snapping of a wire.

Cut and remove the part of gilt which comes off at the point. (Take care that there are some pieces of gilt left inside)

[Discharging of the FLASH unit's charging capacitor]
1 k/1 W

The charging capacitor of the FLASH unit is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the DSC-H1 is simply turned off. Therefore, the remaining voltage must be discharged as described below. Preparing the Short Jig To preparing the short jig. a small clip is attached to each end of a resistor of 1 k /1 W (1-215-869-11) Wrap insulating tape fully around the leads of the resistor to prevent electrical shock. Discharging the Capacitor 1 Remove the main section. 2 Discharge the capacitor on the ST-123 board for about 10 seconds by using the short jig.

Wrap insulating tape.

Caution
1 Discharging the capacitor

Capacitor

Short jig (1k/1W)

ST-123 board

DSC-H1 1-1

[Description on Self-diagnosis Display]

Self-diagnosis display · C: ss: ss The contents which can be handled by customer, are displayed. · E: ss: ss The contents which can be handled by engineer, are displayed.

Display Code C:32:01

Countermeasure Turn off the main power then back on. Replace the memory stick. Format the memory stick with the DSC-H1. Checking of flash unit or replacement of flash unit.

Cause Trouble with hardware. · The type of memory stick that cannot be used by this machine, is inserted. · Data is damaged. · Unformatted memory stick is inserted. Abnormality when flash is being charged.

Caution Display During Error SYSTEM ERROR

C:13:01

MS ERROR Flash LED Flash display Flashing at 3.2 Hz

E:91:01 E:01:XX E:61:00 *1 E:61:10 *1

Checking of lens drive circuit

When failed in the focus initialization.

--

Note : The error code is cleared if the battery is removed, except defective flash unit. *1: The error display is given in two ways.

DSC-H1 1-2

· METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note: 1 When replacing the SY-127 board, erase the data in internal memory of the board before replacement. Note: 2 When replacing the SY-127 board or the IC381 on the SY-127 board, execute formatting and initialize the internal memory after replacement.

Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a "Memory Stick".
OK Cancel
See the following procedure. Cancels the copying.

1 Insert a "Memory Stick" having 32 MB or larger capacity. 2 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be copied Ready?" appears. 3 Select [OK] with v , then press z. Copying starts.

Copying 102_COPY

Use batteries with enough capacity or the AC Adaptor (not supplied). If you attempt to copy image files using batteries with little remaining capacity, the batteries may run out, causing copying to fail or possibly corrupting the data. You cannot copy individual images. The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the "Memory Stick" after copying, then execute the [Format] command in Internal Memory Tool. You cannot select a folder copied on a "Memory Stick". The setting of (Print order) marks is not copied even when you copy data.

Method for Formatting the Internal Memory
Format
Formats the internal memory.
Note that formatting irrevocably erases all data in the internal memory, including even protected images.

OK Cancel

See the following procedure. Cancels the formatting.

1 Select [OK] with v on the control button, then press z. The message "All data in internal memory will be erased Ready?" appears. 2 Select [OK] with v, then press z. The format is complete.

· PROCESS AFTER FIXING FLASH ERROR
When "FLASH error" (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.

Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting.
OK Cancel
See the following procedure. Cancels the resetting.

1 Select [OK] with v on the control button, then press z. The message "Initialize all settings Ready?" appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting.
Make sure that the power is not disconnected during resetting.

DSC-H1 1-3E

2. DISASSEMBLY
The following flow chart shows the disassembly procedure.

2-1. DISASSEMBLY
2

2 4 2 1 -12 SY 5 5 1 Three screws (M2x4) silver 2 Three screws (M2x4) silver 3 Remove the JK lid in the 4 3 1 1 Light guide plate (2.5) block 3 1 2 Two claws 3 Remove the LCD, Light guide plate (2.5) block 1 Tapping screw (M1.7x4) black 2 Three claws 3 Claw 4 LCD frame assembly 4 7 3

direction of the arrow.
4 Claw 5 Cabinet (rear) section

in the direction of the arrow.
4 LCD unit 5 LCD unit, Light guide plate (2.5) block 3 1

Note: Be very careful not to
6 1 EV-016 board 2 Two claws 3 EVF section 7 -12 SY 5 2 4 3 S 1 1 Flexible flat cable (MS-029) 2 Battery connector 3 From the loudspeaker 4 Three tapping screws (M1.7x4) black 5 Fuse replacement caution label 6 SY-127 board 3 4 5 6 7 -12 SY 6 1 From the lens flexible board 7 6 2 FP-224 flexible board 3 From the lens flexible board 4 Flexible flat cable (ST-001) 5 Control switch block (SW51780) 6 AF-102 flexible board 1 Flexible flat cable (MS-029) 2 Tapping screw (M1.7x4) black 3 Two claws 4 MS-275 board 5 Battery connector 6 Three claws 7 Battery terminal board 1 7 4 5 -27 MS 5 SY -12 7 1 2 3 3 7 From the microphone 8 Tapping screw (M1.7x4) black 9 Main section 2 S 7 1 2 Y-1 7 1 Flexible flat cable (SW-006) 8 2 Four tapping screws (M1.7x4) black 3 Claw 4 SW-447 board 5 2 1 4 2 9 3 2 Y-1 7 -44 SW 7

damage the flexible board.

SY-127

4

ST section
2

(See page 2-3.)

DSC-H1 2-1 2-2

2. DISASSEMBLY

2

Caution
1 Discharging the capacitor

Capacitor
2 1

Short jig (1k/1W)
1 Two tapping screws (M1.7x4) black 2 Lens section 1

ST-123 board
1 Tapping screw (M1.7x4) black 2 Control switch block (SW51780), Microphone unit

1

5

6 HELP 01 4 1 Tapping screw (M1.7x4) black 2 Claw 3 ST-123 board 4 Three harnesses (HA-001) (Red, White, Blue) 5 Open the ST cover in the direction of the arrow. 6 ST section 2 1 4 2 3 HELP 02 3

1 Remove the AF-102 flexible board

in the direction of the arrow.
2 Three claws 3 Three claws 4 AF-102 flexible board

DSC-H1 2-3 2-4

2-2. SERVICE POSITION

2

[SERVICE POSITION TO CHECK THE SY-127 BOARD]
1

From the lens section FP-224 flexible board
2

SW-447 board

2
4

Lens section
5

SW -44

Flexible flat cable (SW-006)
7

Monitor TV

3 1

1

Audio/Video jack

CN401 CN502

S
CN513

1

5

Y -1

2

CN101

2

7

Caution
1 Discharging the capacitor

SY-127 board
CN509

4 3

Capacitor

Short jig (1k/1W)

From the lens section Flexible flat cable (MS-029)
M S

CN506 CN514

Battery terminal board

ST-123 board

-2 7 5

MS-275 board
1

-12 SY

7 3 2

2

6 7 -12 SY
1 4

3 4

5

Battery section

3 1

Control switch block (SW51780)
3 -12 SY 7 -44 SW 1 4 7

Insert the batteries (size AA). Nickel Metal Hydride batteries (x2).

2

7 -12 SY

2

6

MS-275 board
5 9 4 3 7 1 -12 SY 7 2

8

Flexible flat cable (MS-029)

DSC-H1 2-5 2-6

2. DISASSEMBLY

2-3. CIRCUIT BOARDS LOCATION
AF-102 ST-124 ST-123

MS-275 PL-039

CD-576

SW-447 CH-169 SY-127 EV-016

NAME AF-102 CD-576 CH-169 EV-016 MS-275 PL-039 ST-123 ST-124 SW-447 SY-127

FUNCTION AF LED, LENS COVER SW CCD IMAGER CCD SIGNAL PROCESS EVF, BACK LIGHT MEMORY STICK, LI BATTERY PLUNGER FLASH DRIVE FLASH FUNCTION SW, PITCH/YAW SENSOR AMP LENS DRIVE, CAMERA A/D CONV., TIMING GENERATOR, CAMERA DSP, SYSTEM CONTROL, 256Mbit SDRAM, FLASH MEMORY, SUPER AND FLASH MEMORY, A/V AMP, USB/AV JACK, SP, MIC, PANEL DRIVE, STEADY SHOT CONTROL, LENS SERVO, CONNECTOR, DC/DC CONVERTER

DSC-H1 2-7

2. DISASSEMBLY

2-4. FLEXIBLE BOARDS LOCATION
The flexible boards contained in the optical unit are not shown.

CONTROL SWITCH BLOCK (SW51780)

MS-029

SW-006

FP-224

ST-001

DSC-H1 2-8E

HELP
Disassembling and assembling procedures that require attention are described here.
HELP 01

Harness (HA-001) (Blue)

Harness (HA-001) (White) Harness (HA-001) (Red)

HELP 02 6 7 2White 8 1 Harness (H-001) (Red) 2 Harness (H-001) (White) 3 Harness (H-001) (Blue) 4 Apply the soldering in three points. 5 ST-123 board 6 ST-124 board 7 Four claws 9 1Red 3Blue 8 ST cover 9 Tapping screw (M1.7x4) black 0 ST section

Blue Red
4

0

White
5

DSC-H1

HELP

3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (2/2)

DSC-H1

3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

Ver 1.1 2005. 09

LENS UNIT
IRIS SHUTER

CD-576 BOARD

FP-224 FLEXIBLE BOARD

SY-127 BOARD (1/2)
22 | 35 CA AD0 - CA AD13 K5,G4,H4,L5 H2,H1,J1,J2 M5,J4,K4,M6 K2,K1 AC4,AE4 AE5,AC5 AB6,AF6 MS D0-MS D3, MS BS, MS CLK XMS IN 8 CN506

MS-029 FLEXIBLE BOARD (1/2)
CN251 7,8,6, 4,9,3 5 4,3,5,7,2,8 CN252 MEMORY STICK CONNECTOR

IC101
CCD IMAGER 15 1
V1A,B V2 V3A,B V4 V5A,B V6 V7A,B V8, VST, VHLD

IC102
BUFFER

CCD OUT 3 22 22 6

S/H A/D CONV.

6,5,7, 9,4,10

X301

(3/11)
EXTAL A6

6

(2/11)

12MHz XTAL OSC

1-14

27,28 19-17 H1A,B H2A,B RG 12 10 8 6 18 CN101 12 10 8 6 18 CN502 1 | 5

CP201
TIMING GENERATOR 47 45 46 CLK TGO

F2 E1 H5 J5

IC301 (1/2)
CAMERA DSP

MS-275 BOARD (1/2)
K2 K3 K1 J6 K4 VR VG VB CN505 4 5 3 24 23 6 PANEL REF PANEL VST VCK,EN DWN,XSTB M PCG,HST HCK2,HCK1 RGT 22 | 19 14 | 11 8 7 2 LCD901 2.5 INCH COLOR LCD PANEL

CN101 25-38

CA HD, CA FD

25-38 CN502

(7/11)
7 | 20 42 D21,D22,D20,B22,A22,A23 B23,E20,E21,B24,A24,A25 B25,C25,C26,B26,E10,A10 D10,E11,B10,A11,B11,E12 D11,D12,F12,B12,A12,E13 D13,D14 D17,D18,D16,B18,A19 B19,E16,D19,E19,E17 B20,A20

IC601
D8,D7,E8 E7,D6,D5 E6,B4 E9 B8 D9 LCD D0-D7 LCD HD LCD VD LCD CK B3,A3,B4 B5,A5,B6 A7,B7 A9 C9 A2 SAN1 SO, SCK B9 A10 C10 RGB DRVE TIMING GENERATOR

IRIS MOTOR

M
SHUTTER MOTOR

1 4

IRIS A IRIS XA IRIS B IRIS XB

(1/11)
F2 E2 D2 B1 F3 F4 D6 E6 B7 C6

IC401
(1/2)
IRIS DRIVE SHUTTER DRIVE

M
FOCUS MOTOR

8 5

SHUTTER + SHUTTERFOCUS A FOCUS XA FOCUS B FOCUS XB

G1 E4 D5 A6 B6 C5

MSHUT DIR MSHUT EN

SAN1 SO,SCK

F5 E5 D3 F1

DIR2A BRK2A DIR2B BRK2B

(4/11)
40 41

D0-D31

PANEL COM/CS

IC353
256Mbit SDRAM A0-A11

M
ZOOM MOTOR

9 16

FOCUS MOTOR DRIVE

FC DIR A FC DIR B FC EN

DIR2A BRK2A DIR2B BRK2B

N4 P6 P4 R2 R25 R5 L2 N5 L4 N6 N2 U4 U5 V4 V5 W4

U2 T2 SAN1 SO, SI, SCK R6 AF4 XSAN RST OUT

PSIG PANEL REF XSTB E PANEL VST VCK,EN DWN,XSTB M J4,H1 PCG,HST H2,G1 HCK2,HCK1 G2,F1 RGT F2,E2 D1,D2 C2,B1

MSHUT DIR MSHUT EN FC DIR A FC DIR B FC EN ZM DIR A ZM BRK A

VR VG VB

CN508 5 8 9 3 4 7 21 | 17 14 | 10 6

CN001 17 18 16 21 19 20

M
FOCUS RESET SENSOR ZOOM RESET SENSOR 1ST ZOOM RESET SENSOR 2ND ZOOM DC FG

36 39

ZOOM + ZOOM -

B4 B5

ZOOM MOTOR DRIVE

A2 B2

ZM DIR A ZM BRK A

J7

EVF COM/CS PSIG

LCD902 COLOR EVF UNIT

22

FC SENS FC SENS ZM SENS 1ST ZM SENS 1ST ZM SENS 2ND ZM DC FG 1A ZM DC FG 1B

(7/11)

IC602
EVF BL ON EVF BL LEV EVF BACK LIGHT DRIVE

Q602,603

24

25 32 31 CN401

ZM SENS 2ND ZM DC FG 1A ZM DC FG 1B F4

XMS IN B5 XSHIFT ON XDD RST OUT USB VBUS

(9/11)
ACTIVE LENS ACTUATOR PITCH 7 6

(5/11)

(4/11)

TO OVERALL BLOCK DIAGRAM (2/2)

PANEL REF PANEL VST VCK,EN DWN,XSTB E PCG,HST HCK2,HCK1 RGT EVF BL L

EV-016 FLEXIBLE BOARD

15 | 5

1

1
M 5V EVF BL H 2 D001 (EVF BACK LIGHT)

(9/11)
P DRIVE A P DRIVE B 7 6

IC101
3 1

IC381
SUPER AND FLASH MEMORY

IC351
FLASH MEMORY SAN1 SO, SCK L26 AUIN F3 E3 E6

(PAGE 3-4)
(6/11)

IC103
PITCH DRIVE

(9/11)

2

7

(9/11)

6

7

(9/11)

3 4

PITCH PWM 2

(9/11)
8 YAW 9 Y DRIVE A Y DRIVE B 7 6

IC104
PRE DRIVE 3 7 6 8

IC105
LPF 9 8

IC106
LPF 12

(9/11)

IC801
MIC AMP B6 A5 A2 SPEAKER AMP

CN510 2
MIC SIG SP+ SP-

MIC

MIC901

IC102
YAW DRIVE

IC107
YAW PWM 4 2

A20,A21,A25 D0-D15 D0-D15

A01-A21 C1 AUOUT 1 2 CN511 K26 E5 AU OUT AMP D1 C2
SP901 SPEAKER

D0-D15

AB13,AA13,AE13,AF13,AF12 AE12,AA12,AC12,AC11,AB12 AE11,AF11,AE10,AB11,AC10 AB10 AF21,AF20,AE20,AB18,AB19 AC19,AB16,AE19,AF19,AF18 AE18,AA15,AC18,AC17,AB15 AE17,AF17,AE16,AB14,AC16 AC15,AE14,

2 4 CN101

PITCH POS AD YAW POS AD

A01-A21,A25 131 132 1 3 95 96 66 65 63 37 38 9 8 184 EVF BL ON EVF BL LEV PITCH PWM YAW PWM

3,2 AC1 AD1
Q301

CN751 (USB)

(8/11)

USB DPP, USB DMM USB VBUS 1

X902 20MHz
SE401

IC901
STEADY SHOT CONTROL

SAN1 SO, SI, SCK V LINE OUT 5

(6/11)

T5 V OUT U25 H26 XAV JACK IN

IC802
VIDEO AMP

3

V LINE OUT

J751 A/V OUT

PITCH SENSOR
SE402

8

IC401
PITCH/YAW SENSOR AMP

2

9

PITCH AD

12

129

AU LINE OUT XDD RST OUT SAN1 SO, SI, SCK XSHIFT ON

YAW SENSOR

12

18 CN451

7

YAW AD

14 CN513

130

SW-447 BOARD (1/2)
SW-006 FLEXIBLE FLAT CABLE (1/2)

DSC-H1 3-1 3-2

Ver 1.1 2005. 09

3-2. OVERALL BLOCK DIAGRAM (2/2)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-127 BOARD (2/2)
ST-001 FLEXIBLE FLAT CABLE
(3/11)
12 | 10 1 | 3

ST-123 BOARD

ST UNREG T001 15 D001 (RECT) XE H

FLASH UNIT (ST-124 FLEXIBLE BOARD)

MS-275 BOARD (2/2)
CN251

MS-029 FLEXIBLE FLAT CABLE (2/2)
VL 3V 11 2 CN506

IC301 (2/2)
SYSTEM CONTROL

STRB CHG R22 XSTRB FULL V23 STRB CHG CONT AB22

4 5 6

STRB CHG XSTRB FULL STRB CHG CONT

9 8 7

10 9 6

HIGH VOLTAGE CHAGER

1 2

C004

L001 TRIGGER COIL

IC001
IGBT DRIVE 7

Q001 FLASH DRIVE XE L D001

XENON TUBE

STRB ON R4 CN501

7

STRB ON

6 CN001

4

BT251 LITHIUM BATTERY (SECONDARY)

(1/11)

STRB PLUNGER ON AA25

A1

IC401 (2/2)
STRB PLUNGER DRIVE

CN507 B3 8 7

AF-102 FLEXIBLE BOARD
STRB PLUNGER 4 3

RY301 PLUNGER

XSTRB POPUP V22 XLENS COVER SENS AC23 VL 3V

5 1 XAF LED

1

S301 (STRB POP UP)
CN301

S001 (LENS COVER OPEN)

4 4 3 2 1
UNREG REG GND F001 ST UNREG

D001 (AF LED)

PL-039 BOARD

BATTERY TERMINAL

CN514 CN509 SAN0 SO C5 SAN0 SI C6 XSAN0 SCK B6
BATT SENS G5 XDD RST OUT
A7 B7

S103
8 7 7 8

SAN0 SO, SI, SCK

AB5 AA5 Y5 K25 Y4 R26 A23

SAN0 SO SAN0 SI XSAN0 SCK BATT SENS XDD RST OUT XPWR OFF

XAE LOCK SW XSHUTTER SW MODE DIAL 0 MODE DIAL 1

N21 P23

SHUTTER

CONTROL SWITCH BLOCK(SW51780)
S105

L22 L25 AB23 W22 G25

14 12 10 9

1 3 5 6

MODE DIAL

(11/11)
UNREG F002

XPWR OFF

JOG A JOG B

JOG DIAL S106,101,102 EXEC

IC001
DC/DC CONVERTER REAL TIME CLOCK
A8
OSC I OSC O

EVER 3.1V EVER 2.8V D 3.2V D 3.2V (TO CAM) D 3.2V (TO SP) A 3.2V MS VCC CAM 2.9V (TO CAM) CAM 2.9V (TO PANEL) D 1.8V M 5V ST 5V D 1.2V PANEL 8.5V BL H BL L A4 XAF LED

KEY AD2 XSTRB LED XPWR LED

11

4

EVF/LCD, FOCUS, BRK

E22 D23

1 3

14 12

D101 (FLASH) D102 (POWER) S104

X001 32.768KHz

A9 B8

4

11

XPWR ON

POWER S107

VL 3V

C7 C9

XPWR ON USB VBUS

1
KEY AD0 K23

TO OVERALL BLOCK DIAGRAM (1/2)

XSHIFT ON
USB VBUS XMS IN XDD RST OUT

6

9

XSHIFT ON

STEADY SHOT

B10 XMS IN

(PAGE 3-2)

CN513 20 1

S458,460,456,454,457,453 DOWN, RIGHT, UP, LEFT, SET, DUST S459,455,452,451

(11/11)

KEY AD1 L23 CAM 15V CAM -7.5V XACCESS LED E4

19

2

ZOOM WIDE, ZOOM TELE, MENU, DISPLAY

LED901 LCD BACK LIGHT 6 4

IC005
-7,5V/15V REG

1 5 4 3 2 BL H BL L

20 16 17 18 19 CN451

D455 (ACCESS)

(11/11)

IC004
DC/DC CONV.

CN452

STEADY 5V

SW-006 FLEXIBLE FLAT CABLE (1/2)

SW-447 BOARD (2/2)

DSC-H1 3-3 3-4

Ver 1.1 2005. 09

3-3. POWER BLOCK DIAGRAM (1/2)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-127 BOARD (1/2)
4 3
BATTERY TERMINAL

ST-001 FLEXIBLE FLAT CABLE
ST UNREG ST UNREG

ST-123 BOARD
T001 1 | 3 9 8 7 4 CN001
15

D001 (RECT) XE H XENON TUBE

UNREG

F001

12 | 10 4 5 6 9

STRB CHG 2 REG GND 1 CN509 XSTRB FULL

L001
10 9 6

IC001
HIGH VOLTAGE CHAGER IGBT DRIVE

1 2

C004

6 8 L010
9

(11/11)

STRB CHG CONT

IC004
2

STEADY 5V

ST 5V
CN501

3

DC/DC CONV. 1

FLASH UNIT (ST-124 FLEXIBLE BOARD)

F002

MS VCC
UNREG

MT 5V

(6/11)
AU 3.2V D 3.2V (TO SP) D 3.2V (TO CAM) D 3.2V A 3.2V D 3.2V (TO CAM) D 3.2V A 3.2V

(11/11)

IC801
MIC AMP SPEAKER AMP AU OUT AMP

CN252 MEMORY STICK CONNECTOR

MS-275 BOARD
9 CN251 MS VCC 2 11
R002

IC001
DC/DC CONVERTER REAL TIME CLOCK EVER 2.8V EVER 3.1V VL 3V
CN506 STRB CHG XSTRB FULL STRB CHG CONT
R22 V23 AB22

PWR1-1 A1 PWR1-2 B1 PWR1-3 C2 VO1-1 F1 VO1-2 F2 VFB1 H2 MS PWR IN MS PWR LDO3IN 2.9V REG LDO3 L011
G1

D001

J1 UNREG1-1,2 K1
H1

LDO1

3.1V REG.

L001

(6/11)
4 3

BT251 LITHIUM BATTERY (SECONDARY)

VL 3V

11 2

B8 RTC BAT
A8 OSC I

MS VCC
G2

IC803
1

AU 3.2V

3.2V REG

X001 32.768KHz

B2

(3/11)

A9 OSC O

CAM 2.9V
A2

CAM 2.9V

IC301
CAMERA DSP SYSTEM CONTROL

K25 Y4 R26 AA23 T25

BATT SENS XDD RST OUT XPWR OFF MS PWR ON

G5 UNREGMON A7 XRESET B7 XPWR OFF MS PWR ON D3

LDO2IN 1.8V REG LDO2

CAM 2.9V
B3

L803

VI 3.2V D 1.8V

A3

UNREG2

CONTROL SWITCH BLOCK (SW51780)
-7.5V ON
P25

XCS DD SAN0 SO SAN0 SI XSAN0 SCK

W23 AB5 AA5 Y5

XCS DD C5 SAN0 SO C6 SAN0 SI B6 XSAN0 SCK
A6

J6 K6

PWR56 OUT J7 K7 LX5-1 LX5-2 LX5-3 LX5-4 VO5
J9 J10 K9 K10
H10

L006 7 D003 (RECT) Q004 SWITCHING & RECT

(11/11)
15V REG 6 CAM 15V

D102 (POWER) D101 (FLASH)
D 3.2V

12 3 14 1 13 2 D 3.2V A 3.2V AU 3.2V VI 3.2V D 1.2V

D23 E22

XPWR LED XSTRB LED

IC005
-7.5V REG 3 1 -7.5V ON M 5V 4 CAM -7.5V

VFB5 H9 GT6 H6 VFB6 H7 PWR2
D10

TO POWER BLOCK DIAGRAM (2/2)

1

L009

(PAGE 3-7)

L003 LX2 C10 VFB2 D8
F003

MODE DIAL

A 3.2V

D 1.2V STEADY 5V L005 D 1.2V BL H D002 (RECT) BL L BL L BL H

2 13

S104 POWER XPWR ON
11 4 CN514

XPWR ON

C7 XPWRON1

LX3

E10

VO3 E9

(4/11)
D 3.2V

LV3 RS3

IC353
(5/11)
256Mbit SDRAM

F9 F8

L008 Q001 SWITCHING

Q003 SWITCH M 5V ST 5V ST 5V

IC381
SUPER AND FLASH MEMORY

(4/11)

BG4 G9

AF-102 FLEXIBLE BOARD
D3.2V 3

D 1.8V

IC351
FLASH MEMORY
A4

TG4

F10

VFB4 F7 PSG4 G8
XAF LED

Q002 RECT

PANEL 8.5V CAM 2.9V (TO PANEL)

D001 (AF LED)

XAF LED

4 CN507

VO7 K4

PANEL 8.5V

(6/11)
CAM 3.2V

IC802
D821 VIDEO AMP

-7.5V ON D 3.2V A 3.2V, AU 3.2V, VI 3.2V, D 1.8V, D 1.2V

DSC-H1 3-5 3-6

Ver 1.1 2005. 09

3-4. POWER BLOCK DIAGRAM (2/2)

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-127 BOARD (2/2)
(2/11)
D 3.2V D 3.2V A 3.2V CAM 2.9V

CP201
S/H A/D CONV. TIMING GENERATOR

FP-224 FLEXIBLE BOARD

CD-576 BOARD
IC102
BUFFER

CAM 15V CAM -7.5V

L201

CAM 15V CD CAM -7.5V CN502
16 14 16 14

IC101
CCD IMAGER CN101

D 3.2V

(1/11)

21

FC RST VCC

IC401
M 5V

FOCUS RESET SENSOR

LENS UNIT

(9/11)

IC110
STEADY 5V FULL PWR LIM PWR
CURRENT LIMITER

IRIS DRIVE SHUTTER DRIVE FOCUS MOTOR DRIVE ZOOM MOTOR DRIVE PLUNGER DRIVE Q107,110 VCC CN401

27 28

ZM RST VCC

ZOOM RESET SENSOR

ZM FG VCC
33

ZOOM DC FG

(9/11)

(9/11)

(9/11)

(9/11)

1
TO POWER BLOCK DIAGRAM (1/2)

IC101 IC107
INVERTER

IC105 IC106
LPF

IC104
PRE DRIVE

IC102 IC103
PITCH DRIVE YAW DRIVE

L101
3

A 4.6V CN101

ACTIVE LENS ACTUATOR

(9/11)

(PAGE 3-6)
3

IC108
1

A 4.6V L103

4.6V REG
4

SW-006 FLEXIBLE FLAT CABLE

SW-447 BOARD

(2/2)

IC401
PITCH/YAW SENSOR AMP
11

SE401, 402
PITCH/YAW SENSOR

VAP DD ON A 3.2V D 3.2V

VAP DD ON
10 9 8 18

Q401,402

A 3.2V D 3.2V

12 13 3

D455
ACCESS LED

BL H BL L CN513

5 4 3 2

BL H BL L

16 17 18 19 CN451 4 6

CN452

FULL PWR LIM PWR

154 155

(8/11)

VAP DD ON
170

IC901
STEADY SHOT CONTROL

(7/11)
EVF BL ON EVF BL LEV

PANEL VDD
18

D_1.2V

79 36 191 160

IC601
RGB DRIVE TIMING GENERATOR EVF BL ON EVF BL LEV

LCD901 2.5 INCH COLOR LCD PANEL

LED901 LCD BACK LIGHT

CN505

37 38

(7/11)

IC602
BACK LIGHT DRIVE

Q602, 603 EVF BL L D001 (EVF BACK LIGHT)
1 LCD902 COLOR EVF UNIT

ST 5V PANEL 8.5V CAM_ 2.9V(TO PANEL)

L603 L602

EVF BL H PANEL VDD CN508

2 16

CN001
2

EV-016 FLEXIBLE BOARD

DSC-H1 3-7 3-8E

F

I

E

J

K

L C A B

N H D G M
16

DSC-H1
1
LCD BACK LIGHT SPEAKER 2.5 INCH LCD UNIT AV USB

2

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 11 12 13 14 15 16 17 18 19 20 HST REG_GND 21 22 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 ZM_DC_MOTOR_ZM_DC_MOTOR_ZM_DC_MOTOR_+ ZM_DC_MOTOR_+ XZM_FG_TR XACCESS_LED BL_L BL_L BL_H BL_H REG_GND REG_GND A_3.2V REG_GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 V3B V7B VST V8 V4 REG_GND 34 35 36 37 38 39 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 23 22 21 REG_GND CCD_OUT REG_GND REG_GND V5A V1A V5B V1B VHLD V2 V6 V3A V7A V7A V3B V7B VST V8 V4 REG_GND REG_GND REG_GND STRB_PLUNGER STRB_PLUNGER REG_GND 1 2 3 4 5 6 7 8 9 10 XSTRB_POPUP LENS_VC P_OUT D_3.2V A_4.6V REG_GND Y_OUT REG_GND P_DRIV_B P_DRIV_A Y_DRIV_A Y_DRIV_B N.C. UNREG UNREG REG_GND REG_GND 4 3 2 1 2 3 XAF_LED 10 9 8 7 6 5 4 20 REG_GND 19 REG_GND 18 RG 17 REG_GND 16 CAM_15V_CD 15 POWER_SAVE 14 CAM_-7.5V_CD 13 REG_GND 12 H1A KEY_AD0 20 11 REG_GND KEY_AD1 19 10 H2A D_3.2V 18 9 REG_GND REG_GND 17 8 H1B VST_C_RESET 16 7 REG_GND REG_GND 15 6 H2B YAW_AD 14 5 REG_GND REG_GND 13 4 RAMDOM_TRIGGER 3 VSUB 2 CSUB 1 CSUB VSUB RAMDOM_TRIGGER REG_GND H2B REG_GND H1B REG_GND H2A REG_GND H1A REG_GND CAM_-7.5V_CD POWER_SAVE CAM_15V_CD REG_GND RG REG_GND REG_GND REG_GND CCD_OUT REG_GND REG_GND V5A V1A V5B V1B VHLD V2 V6 V3A REG_GND 1 2 3 4 5 6 7 8 XZM_FG_LED ZM_FG_VCC ZM_DC_FG_1A ZM_DC_FG_1B XZM_RST_TR2 XZM_RST_LED2 ZM_RST_VCC2 ZM_RST_VCC1 XZM_RST_LED1 ZM_SENS_2ND HCK1 ZM_SENS_1ST COM 24 DWN XZM_RST_TR1 CS 23 XSTB_E FC_SENS VST 22 VCK FC_RST_VCC VCK 21 PANEL_VDD XFC_RST_TR EN 20 EVF_VSSG XFC_RST_LED DWN 19 HCK2 LENS_TMP PANEL_VDD 18 RGT REG_GND REG_GND 17 PANEL_REF FOCUS_XA N.C. 16 VST FOCUS_XA PANEL_VSSG 15 10 EN FOCUS_B XSTB_M 14 9 VB FOCUS_B PCG 13 8 VG FOCUS_A HST 12 7 PSIG FOCUS_A PANEL_REF 11 6 PCG FOCUS_XB TEST1 10 VR 5 R B PCG EN VCK VST XSTB REF DWN RGT HCK1 HCK2 HST EVF_VSSG REG_GND VDD N.C. 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 FOCUS_XB N.C. 9 4 G 18 CS SHUTTER_+ HCK2 8 3 CS 19 COM SHUTTER_+ HCK1 7 EVF_BL_H 2 PSIG 20 SHUTTER_PSIG 6 1 COM 21 EVF_BL_L SHUTTER_VG 5 IRIS_XA VR 4 IRIS_B VB 3 IRIS_A RGT 2

4-1. FRAME SCHEMATIC DIAGRAM

IRIS_XB TEST2 1

1 SP_CN505 24P CN511 2P SP_+

2

3 4 5

EVF,BACK LIGHT

EV-016 FLEXIBLE BOARD

4-1
CN508 22P CN401 39P

6

COLOR EVF UNIT

CN001 21P

LENS UNIT
CN513 20P
A_3.2V VAP_DD_ON REG_GND PITCH_AD 9 10 11 12

7

6 BL_H

5 N.C.

4 BL_L

3 N.C.

2 N.C.

1 N.C.

8

CN452 6P

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

KEY_AD0 KEY_AD1 D_3.2V REG_GND VST_C_RESET REG_GND YAW_AD REG_GND PITCH_AD REG_GND VAP_DD_ON A_3.2V A_3.2V REG_GND REG_GND BL_H BL_H BL_L BL_L XACCESS_LED

9

SY-SW RELAY

SW-447 BOARD

CN451 20P

10

SW-006 FLEXIBLE FLAT CABLE

(1/2) FUNCTION SWITCH (2/2) PITCH/YAW SENSOR AMP

4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

CCD IMAGER

CD-576 BOARD
SY-CD RELAY

11

FP-224 FLEXIBLE BOARD

CN101 39P

(1/11) LENS DRIVE

(9/11) LENS SERVO

(7/11) PANEL DRIVE

(10/11) CONNECTOR

SY-127 BOARD

(11/11) DC/DC CONVERTER

CN502 39P

PLUNGER

MIC

12

(8/11) STEADY SHOT CONTROL

PL-039 BOARD

(5/11) SUPER AND FLASH MEMORY

(6/11) A/V AMP,USB/AV JACK,SP,MIC

(3/11) CAMERA DSP,SYSTEM CONTROL

(4/11) 256Mbit SDRAM,FLASH MEMORY

(2/11) CAMERA A/D CONV. TIMING GENERATOR

(CH-169 board) CCD SIGNAL PROCESS

CCD IMAGER

6 5 MIC_SIG MIC_GND 2 1 4 3 2 1

REG_GND REG_GND STRB_PLUNGER STRB_PLUNGER REG_GND XSTRB_POPUP

13

CN301 6P

CN510 2P CN507 10P

14

AF-102 FLEXIBLE BOARD
AF LED,LENS COVER SW

LENS COVER SW

15

CN101 10P CN509 4P JOG_B JOG_A REG_GND XPWR_ON KEY_AD2 XPWR_LED D_3.2V XSHUTTER_SW XAE_LOCK_SW XSTRB_LED XSHIFT_ON XMS_IN VL_3V ST_5V STRB_ON XSTRB_FULL STRB_CHG ST_UNREG ST_UNREG ST_UNREG REG_GND

XLENS_COVER_SENSE

1

AF 16 17

A_3.2V

MODE_DIAL1

MODE_DIAL0

STRB_CHG_CONT

REG_GND 1

REG_GND 2

REG_GND 3

MS_CLK

REG_GND

REG_GND

REG_GND MS_VCC

MS_D1

MS_D0

MS_D2

MS_D3

CN514 14P

MS_BS

CN501 12P

CN506 12P

10

11

12

13

14

10

11

12

10

11

12

4

5

6

7

8

1

2

3

4

5

6

7

8

9

9

1

2

3

4

5

6

7

8

9

4-2
FLASH DRIVE

18

BATTERY

ST-001 FLEXIBLE FLAT CABLE
SY-ST RELAY
12 9 8 7 6 5 4 3 2 1 12 REG_GND 11 REG_GND 10 REG_GND CN001 12P ST_5V STRB_ON REG_GND REG_GND ST_UNREG ST_UNREG ST_UNREG STRB_CHG XSTRB_FULL

MS-029 FLEXIBLE FLAT CABLE SY-MS RELAY
9 8 7 6 5 4 3 2 1 14 13 12 11 10 9 8 7 6 5 4 3 2 1 11 VL_3V 10 REG_GND 14P MS_D1 MS_D0 MS_D2 MS_D3 CN251 12P MS_BS JOG_B JOG_A A_3.2V D_3.2V XMS_IN MS_CLK MS_VCC KEY_AD2 REG_GND REG_GND XPWR_ON XPWR_LED XSHIFT_ON XSTRB_LED

19

MODE_DIAL1

MODE_DIAL0

XAE_LOCK_SW

XSHUTTER_SW

STRB_CHG_CONT

CONTROL SWITCH BLOCK (SW51780)

ST-123 BOARD

20

MS-275 BOARD

(LITHIUM BATTERY) (SECONDARY)

MEMORY STICK, LI BATTERY

21

ST-124 FLEXIBLE BOARD
FLASH

SDIO/DATA0

DATA3

DATA2 INT

DATA1

MS_BS

SCLK

Ver 1.1 2005. 09

VSS 10

VCC 9

VSS

10P

8

7

6

5 MEMORY STICK CONNECTOR

4 CN252

3

2

1

22

FRAME SCHEMATIC DIAGRAM

4-2. SCHEMATIC DIAGRAMS
Link
CD-576 BOARD (CCD IMAGER) MS-275 BOARD (MEMORY STICK, LI BATTERY) ST-123 BOARD (FLASH DRIVE) ST-124 FLEXIBLE BOARD (FLASH) PL-039 BOARD (PLUNGER) SW-447 BOARD (1/2) (FUNCTION SW) SW-447 BOARD (2/2)
(PITCH/YAW SENSOR AMP)

EV-016 FLEXIBLE BOARD (EVF, BACK LIGHT) AF-102 FLEXIBLE BOARD
(AF LED, LENS COVER SW)

SW-006 FLEXIBLE BOARD (SY-SW RELAY) MS-029 FLEXIBLE BOARD (SY-MS RELAY) ST-001 FLEXIBLE BOARD (SY-ST RELAY) FP-224 FLEXIBLE BOARD (SY-CD RELAY) CONTROL SWITCH BLOCK (SW51780)

COMMON NOTE FOR SCHEMATIC DIAGRAMS

WAVEFORMS

DSC-H1

4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For schematic diagrams) · All capacitors are in µF unless otherwise noted. pF : µ Link V or less are not indicated except for electrolytics µF. 50 and tantalums. · Chip resistors are 1/10 W unless otherwise noted. k=1000 , M=1000 k. · Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. · Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Kinds of capacitor Temperature characteristics External dimensions (mm) · Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. · Parts with * differ according to the model/destination. Refer to the mount table for each function. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted. · Signal name XEDIT EDIT PB/XREC PB/REC · 2: non flammable resistor · 5: fusible resistor · C: panel designation · A: B+ Line · B: B­ Line · J : IN/OUT direction of (+,­) B LINE. · C: adjustment for repair. · A: VIDEO SIGNAL (ANALOG) · A: AUDIO SIGNAL (ANALOG) · A: VIDEO/AUDIO SIGNAL (ANALOG) · A: VIDEO/AUDIO/SERVO SIGNAL · A: SERVO SIGNAL · Circled numbers refer to waveforms. (Measuring conditions voltage and waveform) · Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 M input impedance is used) · Voltage values change depending upon input impedance of VOM used.) 1. Connection
Pattern box
Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A

Color bar chart
For PTB-450: J-6020-250-A For PTB-1450: J-6082-559-A

Pattern box

100 cm (PTB-450) 40 cm (PTB-1450)

Front of the lens

2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Yellow
H

Cyan Green

White Magenta

A B

A=B

Fig. a (Video output terminal output waveform)

Red Blue
B A Electronic beam scanning frame CRT picture frame

Precautions Upon Replacing CCD imager
· The CD-576 board mounted as a repair part is not equipped with a CCD imager. When replacing this board, remove the CCD imager from the old one and mount it onto the new one. · If the CCD imager has been replaced, carry out all the adjustments for the camera section. · As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light.

Fig.b (Picture on monitor TV)

When indicating parts by reference number, please include the board name.
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

DSC-H1 4-3

4-2. SCHEMATIC DIAGRAMS

For Schematic Diagram · Refer to page 4-49 for printed wiring board.

· Refer to page 4-61 for waveforms

1

2

3

4

5

6

7

8

9

A

CD-576 BOARD
CCD IMAGER
XX MARK:NO MOUNT NO MARK:REC/PB MODE R :REC MODE P :PB MODE
CN101 39P

V1A V1B V2 V3A V3B VST V4 V5A

1 1

B

REG_GND V4 V8 VST V7B V3B V7A V3A

39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R108 0 R2.9 P0 2 Q104 DTC144EMT2L VSUB 1 R109 270k 0 R110 1M 3 C108 XX R11.7 P0
2 1

V5B V4 V8 VST V7B V3B V7A V3A V6 V2 VHLD V1B V5B V1A V5A VHLD
CL109 CL108 CL104 CL101

V6 V7A V7B
CL113

V8

4
Note:IC101 is not included in this complete board of CD-576 board.

14 13 12 11 10
R-6.6/P0 V8 R-6.5/P0 V7B R-6.5/P0 V7A VHLD V6

V4

V5B

V5A

VST

V3B

V3A

V2

V1B

C

V6 V2 VHLD V1B V5B V1A V5A REG_GND

3 7
H1B H2B

2
IC101 ICX495BQF

IC101
CCD IMAGER Note
R11.7/P0 CCD_OUT R15.1/P0 VDD

6
RG

7
CSUB N.C. H1A H2A VL

GND

GND

GND

IC102
BUFFER

R13.3 P0.3 R2.0 P0.1 R1.2 P0.1

R11.0 P0 R11.3 P0

TO FP-224 FLEXIBLE BOARD

CCD_OUT REG_GND REG_GND REG_GND RG REG_GND CAM_15V_CD

IN GND OUT

ISF VCC IDRV

6

R11.7 P0

C102 0.1u 16V B C101 0.01u C103 XX 1 R3.5 P0 2 R104 1500 0 R106 220k R105 1200

E

POWER_SAVE CAM_-7.5V_CD REG_GND H1A REG_GND H2A REG_GND H1B

3

4

R4.1 P0

Q102 3 DTC144EMT2L SWITCH

F

REG_GND H2B REG_GND RAMDOM_TRIGGER VSUB CSUB REG_GND

G
16

DSC-H1 4-5 4-6

C105 0.1u 16V B

C109 0.1u 16V B

5

R15.1 P0

C107 0.1u

(PAGE 4-16)

IC102 CXA3691EN-T9

CL123

CL124

R-7.6 P0 R2.0 P0.1 R1.2 P0.1

D

REG_GND

5

15 16 17 18 19 20 21 22 23 24 25 26 27 28

SUB

V1A

R-0.3 P0 R-7.3 P0 R-0.3 P0 R-0.3 P0 R-0.3 P0 R-6.2 P0 R-0.4 P0 R-0.4 P0 R-0.3 P0 R-0.5 P0 R-0.5 P0

9

8

7

6

5

4

3

2

1

CD-576

For Schematic Diagram · Refer to page 4-49 for printed wiring board.

For Schematic Diagram · Refer to page 4-51 for printed wiring board.

1
EVF,BACK LIGHT

2

3
22P EVF_BL_L EVF_BL_H COM CS VR PCG PSIG VG VB 1 LND002 2 LND003 3 LND004 4 LND005 5 LND006 6 LND007 7 LND008 8 LND009 9 LND010 10 LND011 VST PANEL_REF RGT HCK2 EVF_VSSG PANEL_VDD VCK 11 LND012 12 LND013 13 LND014 14 LND015 15 LND016 16 LND017 17 LND018 XSTB_E DWN HCK1 18 LND019 19 LND020 20 LND021 21 LND022 REG_GND 22 LND001

4
D001 NSCW455T-TC9 (EVF BACK LIGHT)

5

6
1 2 3 4

EV-016 FLEXIBLE BOARD A

CN001 21P 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 COM PSIG CS G R B PCG EN VCK VST XSTB REF DWN RGT HCK1 HCK2 HST EVF_VSSG REG_GND VDD N.C. LCD902 COLOR EVF UNIT

PL-039 BOARD A
PLUNGER
XX MARK:NO MOUNT
CN301 6P REG_GND TO AF-102 FLEXIBLE BOARD REG_GND STRB_PLUNGER STRB_PLUNGER REG_GND 6 5 4 3 2 1 D301 XX S301 (FLASH POP UP) LND301 STATIC_GND C301 1u D302 1SS355TE-17 2 RY301 (PLUNGER) 1

B

TO SY-127 BOARD(7/11) CN508

EN

(PAGE 4-15)

(PAGE 4-34 OF LEVEL3)

B
16

XSTRB_POPUP

C
16

HST

For Schematic Diagram · Refer to page 4-47 for printed wiring board.

1

2

3

4

5

6

MS-275 BOARD A
MEMORY STICK,LI BATTERY
XX MARK:NO MOUNT
CN251 12P REG_GND VL_3V REG_GND MS_BS 12 11 10 9 8 7 6 5 4 3 2 1 R251 0 C251 XX C252 0.1u B 1k CL256 FB254 CL262 0uH 7 8 9 10 DATA3 SCLK VCC VSS R253 FB251 FB252 FB253 0uH 0uH 0uH BT251 (LITHIUM BATTERY) (SECONDARY) CL251 CL257 1 2 3 4 5 6

10P VSS MS_BS DATA1 SDIO DATA2 INT MEMORY STICK CONNECTOR CN252

B

TO MS-029 FLEXIBLE FLAT CABLE

MS_D1 MS_D0 MS_D2 XMS_IN MS_D3 MS_CLK MS_VCC REG_GND

(PAGE 4-15)

C
LND251 STATIC_GND

D251 XX

16

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

DSC-H1 4-7 4-8

EV-016/MS-275/PL-039

For Schematic Diagram · Refer to page 4-51 for printed wiring board.

Ver 1.1 2005. 09

1 ST-123 BOARD
FLASH DRIVE

2

3
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
CN001 12P ST_UNREG ST_UNREG ST_UNREG ST_5V 1 2 3 L001 4.7uH

4

5

6

7

8

9

10

A

XX MARK:NO MOUNT
2

T001 CONVERTER TRANSFORMER D001 FT02P80TP 6 C001 22u 6.3V C005 22u 6.3V LND003 XE_H

1 4 5 6 7 8 3 STRB_CHG REG_GND REG_GND REG_GND 9 10 11 12
3.1

TO ST-001 FLEXIBLE FLAT CABLE

REG_GND STRB_ON STRB_CHG_CONT XSTRB_FULL

B

(PAGE 4-17)

4

5

C004 205u 330V TO ST-124 BOARD

(PAGE 4-17)

C IC001
1

17 16 15 14 13
HGND VBATT N.C N.C N.C

SW PGND SW VCC F_ON IC001 TPS65552RGTR CHG XFULL

10 11 12

HIGH VOLTAGE CHARGE, IGBT DRIVE R001 0

3.1

PGND

LND004 REG_GND 0 3.2

5.1 0
4 3

D
R004 XX C002 1u C

2

9

G_IGBT

I_PEAK

N.C

N.C

5 6 7 R002 4.7M 0 R003 33 8

1 2 3 4 Q001 CY25BAJ-8F-T23 FLASH DRIVE

LND005 R280.0 P13.0

XE_L

5
0

6
0

7

8

E
16
C003 XX

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

DSC-H1 4-9 4-10

ST-123

For Schematic Diagram · Refer to page 4-53 for printed wiring board.

1

2

3

4

5

6

7

8

SW-447 BOARD(1/2) A
FUNCTION SWITCH
XX MARK:NO MOUNT
S459 R457 5600 ZOOM W S455 ZOOM T
8 6 4 2

A_3.2V VST_C_RESET YAW_AD PITCH_AD VAP_DD_ON

A_3.2V VST_C_RESET YAW_AD PITCH_AD VAP_DD_ON

@W01

(2/2)

RB452 2200X4 2 NO 1 1st 4 2nd 5 2 NO 3 6 1 1st 4 2nd 5
7 5 3 1

CN452 6P 1 2 3 N.C. N.C. N.C. BL_L N.C. BL_H LED901 LCD BACK LIGHT

B
2

3 S452 MENU 1 6

4 5 6

R456 27k

4

3

S456 UP

2

1

CN451 20P 1 KEY_AD0 KEY_AD1 D_3.2V REG_GND VST_C_RESET REG_GND YAW_AD REG_GND PITCH_AD REG_GND VAP_DD_ON A_3.2V A_3.2V REG_GND REG_GND BL_H BL_H BL_L BL_L XACCESS_LED TO SW-006 FLEXIBLE FLAT CABLE

2

DISP 2 1
8 6 4 2

RB451 2200X4

D452 MAZW068H0LS0 3

C
4

7 5 3 1

S451

4

3

2 R453 330 3 4 VST_C_RESET
1

5 6

3 R454 5600 2 1 S457 SET 2 1 S460 RIGHT 4 R455 27k 3

YAW_AD

7 8

PITCH_AD
D451 1SS387-TPL3

9 10

D

4 S454 LEFT 4 3 2 2 1

3

VAP_DD_ON A_3.2V

11 12 13 14

(PAGE 4-18)

1

S458 DOWN 2 1

S453 DUST

15 16 17

4

3 4 3 REG_GND

18 19 20 LND451 D455 SML-310LTT86 (ACCESS)

E
16

STATIC_GND

DSC-H1 4-11 4-12

SW-447(1/2)

For Schematic Diagram · Refer to page 4-53 for printed wiring board.

1

2

3

4

5

6

7

8

SW-447 BOARD(2/2) A
PITCH/YAW SENSOR AMP
XX MARK:NO MOUNT

NO MARK:REC/PB MODE R :REC MODE P :PB MODE
L401 10uH

Q401,402 3.2V SWITCH R3.2 P0.5 1 3 3.2 A_3.2V

Q401 2SA2029T2LQ/R R2.5 P3.2

2

R412 47k R411 1k 2 R3.2 P0

R0.1 P3.2 1

B

IC401
PITCH/YAW SENSOR AMP IC0401 1 R1.3 P0 2 3 4 5 6 7 8 9 10 PASS OUT1 AM1 Vref1 HO1 HI1 LO1 LIA1 LIB1 GND NJM3230V(TE2) R3.2/P0.5 VCC C_RESET OUT2 AM2 Vref2 HO2 HI2 LO2 LIA2 LIB2 20 19 18 17 16 15 14 13 12 11 R0 P3.1 R1.2 P0 R1.3 P0 R1.3 P0 R1.3 P0.2 R1.3 P0 R1.3 P0 R0.8 P0 R0.6 P0 C410 0.047u
1

VAP_DD_ON

Q402 DTC144EMT2L 3 PITCH_AD C411 0.1u C416 22u 6.3V TA A

@W01

(1/2)

C

C401 22u 6.3V TA A

R403 15k SE401 (PITCH SENSOR)
3 1

R404 1M R405 10k

VST_C_RESET YAW_AD

R1.3 P0 R1.3 P0 R1.3 P0.2

C404 0.33u

R406 1M R407 10k

R408 15k C414 0.33u

C406 10u R401 22k R402 22k

C408 10u

4

2

R1.3 P0 R1.3 P0

C409 10u

C412 10u

C405 0.047u

R0.9 P0 R0.7 P0

D
C403 0.1u C402 22u 6.3V TA A C407 0.047u SE402 (YAW SENSOR)
3

C413 0.047u

R409 22k

R410 22k

C415 0.1u

4

E
16

2

REG_GND

DSC-H1 4-13 4-14

SW-447(2/2)

For Schematic Diagram · Refer to page 4-47for printed wiring board.

Ver 1.1 2005. 09

1

2

3
D001 DOR5073 (AF LED) 1 2 3 6 5 4

4

5

1

2 FP-224 FLEXIBLE BOARD

3

4

5

AF-102 FLEXIBLE BOARD
AF LED,LENS COVER SW

A
10P XLENS_COVER_SENSE REG_GND TO SY-127 BOARD(10/11) CN507 D_3.2V XAF_LED XSTRB_POPUP REG_GND STRB_PLUNGER STRB_PLUNGER REG_GND 1 2 3

S001 (LENS COVER OPEN) LND001 LND002 LND003 LND004 4 LND005 5 LND006 6 LND007 7 LND008 8 LND009 9 LND010 REG_GND 10

A

SY-CD RELAY
39P REG_GND 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 39P 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 REG_GND V4 V8 VST V7B V3B V7A V3A V6 V2 VHLD V1B V5B V1A V5A REG_GND REG_GND CCD_OUT REG_GND REG_GND REG_GND RG REG_GND CAM_15V_CD POWER_SAVE CAM_-7.5V_CD REG_GND H1A REG_GND H2A REG_GND H1B REG_GND H2B REG_GND RANDOM_TRIGGER VSUB CSUB REG_GND TO CD-576 BOARD CN101

LND012 1 LND013 2 LND016 3 LND011 4 LND020 5 LND021 6

6P XSTRB_POPUP REG_GND STRB_PLUNGER STRB_PLUNGER REG_GND REG_GND TO PL-039 BOARD CN301

V4 V8 VST V7B

(PAGE 4-39 OF LEVEL3)

B
16

(PAGE 4-8)

B

V3B V7A V3A V6 V2 VHLD V1B V5B

C
TO SY-127 BOARD (2/11) CN502

V1A V5A REG_GND REG_GND CCD_OUT REG_GND

1

2

3

4

5

(PAGE 4-23 OF LEVEL3)

REG_GND REG_GND RG REG_GND CAM_15V_CD POWER_SAVE

(PAGE 4-5)

D
MS-029 FLEXIBLE FLAT CABLE A
SY-MS RELAY
12P REG_GND MS_VCC MS_CLK TO SY-127 BOARD(10/11) CN506 MS_D3 XMS_IN MS_D2 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 12P REG_GND MS_VCC MS_CLK MS_D3 XMS_IN MS_D2 MS_D0 MS_D1 MS_BS REG_GND VL_3V REG_GND TO MS-275 BOARD CN251

CAM_-7.5V_CD REG_GND H1A REG_GND

E
(PAGE 4-7)

H2A REG_GND H1B REG_GND H2B REG_GND RANDOM_TRIGGER VSUB

B

(PAGE 4-39 OF LEVEL3)

MS_D0 MS_D1 MS_BS REG_GND VL_3V REG_GND

F
16

CSUB REG_GND

C
16

MS-029 FLEXIBLE FLAT CABLE is replaced as a block. So that this PRINTED WIRING BOARD is omitted.

FP-224 FLEXIBLE BOARD is replaced as a block. So that this PRINTED WIRING BOARD is omitted.

DSC-H1 4-15 4-16

AF-102/FP-224/MS-029

Ver 1.1 2005. 09

1
SY-ST RELAY

2

3

4

5

1

2

3

4

5

ST-001 FLEXIBLE FLAT CABLE A
ST_UNREG ST_UNREG ST_UNREG TO SY-127 BOARD (10/11) CN501 ST_5V REG_GND STRB_ON STRB_CHG_CONT XSTRB_FULL STRB_CHG REG_GND 12P 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 12P ST_UNREG ST_UNREG ST_UNREG ST_5V REG_GND STRB_ON STRB_CHG_CONT XSTRB_FULL STRB_CHG REG_GND REG_GND REG_GND TO ST-123 BOARD CN001

SW-006 FLEXIBLE FLAT CABLE A
SY-SW RELAY
XX MARK:NO MOUNT
20P KEY_AD0 KEY_AD1 D_3.2V REG_GND VST_C_RESET 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20P KEY_AD0 KEY_AD1 D_3.2V REG_GND VST_C_RESET REG_GND YAW_AD REG_GND PITCH_AD REG_GND XFE_ON/VAP_DD_ON A_3.2V A_3.2V REG_GND REG_GND BL_H BL_H BL_L BL_L XACCESS_LED TO SW-447 BOARD (1/2) CN451

B

(PAGE 4-40 OF LEVEL3)

(PAGE 4-9)

B

REG_GND TO SY-127 BOARD (10/11) CN513 YAW_AD REG_GND PITCH_AD REG_GND XFE_ON/VAP_DD_ON A_3.2V

16

REG_GND REG_GND

(PAGE 4-40 OF LEVEL3)

(PAGE 4-12)

ST-001 FLEXIBLE FLAT CABLE is replaced as a block. So that this PRINTED WIRING BOARD is omitted.

A_3.2V

C

REG_GND REG_GND BL_H BL_H BL_L

For Schematic Diagram · Refer to page 4-52 for printed wiring board.

16

BL_L XACCESS_LED

SW-006 FLEXIBLE FLAT CABLE is replaced as a block. So that this PRINTED WIRING BOARD is omitted.

1
FLASH
XX MARK:NO MOUNT

2

3

4

5

ST-124 FLEXIBLE BOARD A

LND005 LND001 XE_H R001 1M C002 0.047u 250V L001 TRIGGER COIL XE_+

LND004 TRIGGER

B

XENON TUBE

TO ST-123 BOARD

(PAGE 4-10)
LND002 XE_L

C003 0.01u 250V

XE_D001 RR255L-400TE25 R002 100k 1/10W

C
REG_GND

LND003

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

16

DSC-H1 4-17 4-18

ST-001/ST-124/SW-006

Ver 1.1 2005. 09

1

2

3

4

5
R111 2K R112 2K

6

7

8

A

CONTROL SWITCH BLOCK (SW51780)
R104 2K

R109 2K

R113 2K R115 2K

6 5 4

7

14

13 12 11 10

S101 AF/MF

S102 BRK

R105 2K R106 2K R107 2K

R116 2K R117 2K R118 2K

S106 EVF/LCD

S107 STEADY SHOT

3 2
R110 2K R108 10K

B
R101 4900

1

8

9

R114 2K

C

R102 7130 3

S103 SHUTTER 1

R103 2200

S104 POWER S105 JOG DIAL

4

2

D

D102 (POWER) D101 (FLASH)

E
14 13 12 11 10 9 8 7 6 5 4 3 2 REG_GND XAE_LOCK_SW XPWR_ON XSHIFT_ON MODE_DIAL1 XSHUTTER_SW MODE_DIAL0 XPWR_LED KEY_AD2 XSTRB_LED

LND115 STATIC_GND

CONTROL SWITCH BLOCK(SW51780) is replaced as a block. So that this PRINTED WIRING BOARD is omitted.

14P

JOG_B

D_3.2V

JOG_A

16

TO SY-127 BOARD(10/11) CN514

A_3.2V

1

(PAGE 4-41 OF LEVEL3)

Schematic diagram of the CH-169 and SY-127 board are not shown. Pages from 4-21 to 4-44 are not shown.

DSC-H1 4-19 4-20

SW51780

4-3. PRINTED WIRING BOARDS
Link
CD-576 BOARD MS-275 BOARD ST-123 BOARD ST-124 FLEXIBLE BOARD PL-039 BOARD SW-447 BOARD EV-016 FLEXIBLE BOARD AF-102 FLEXIBLE BOARD

COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION CIRCUIT BOARDS LOCATION

WAVEFORMS FLEXIBLE BOARDS LOCATION

NAME AF-102 CD-576 CH-169 EV-016 MS-275 PL-039 ST-123 ST-124 SW-447 SY-127

FUNCTION AF LED, LENS COVER SW CCD IMAGER CCD SIGNAL PROCESS EVF, BACK LIGHT MEMORY STICK, LI BATTERY PLUNGER FLASH DRIVE FLASH FUNCTION SW, PITCH/YAW SENSOR AMP LENS DRIVE, CAMERA A/D CONV., TIMING GENERATOR, CAMERA DSP, SYSTEM CONTROL, 256Mbit SDRAM, FLASH MEMORY, SUPER AND FLASH MEMORY, A/V AMP, USB/AV JACK, SP, MIC, PANEL DRIVE, STEADY SHOT CONTROL, LENS SERVO, CONNECTOR, DC/DC CONVERTER

DSC-H1

4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR WIRING BOARDS (In addition to this, the necessary note is printed in each block)
(For printed wiring boards) · : Uses unleaded solder. : Pattern from the side which enables seeing. · (The other layers' patterns are not indicated) · Through hole is omitted. · Circled numbers refer to waveforms. · There are a few cases that the part printed on diagram isn't mounted in this model. · C: panel designation

· Chip parts. Transistor
C

6 5 4 4 5 6 5

4 4

5

Diode
3

3

3

1 23

B

E

1 2 3 3 2 1 1 2 3 3 2 1 1 2 2 1 3 4

2 1

1 2 2 3

1 2 4 4

1 6 54 3 3 4

5 4 3 3 4 5 2

1

4 5

3 2 4

6

1 1 2 4 3

2

1

1

3 1

3

1

2

BOARD INFORMATION board name CD-576 MS-275 ST-123 ST-124 PL-039 SW-447 EV-016 AF-102 SY-127 waveforms 4-61 ­ ­ ­ ­ ­ ­ ­ 4-62 parts location 4-63 ­ ­ ­ ­ 4-63 ­ ­ 4-64 2 2 2 1 2 2 1 1 8 pattern ­ ­ ­ ­ ­ ­ ­ ­ 2 to 7 (shown on page) (shown on page) number of layers layers not shown

DSC-H1 4-45

4-3. PRINTED WIRING BOARDS
· Refer to page 4-45 for common note for printed wiring board.

·

: Uses unleaded solder.

AF-102 FLEXIBLE BOARD

LND021 LND020 LND011 LND016 LND013 LND012

A
6

10 1 LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002 LND001 1 S001

K

1-867-1296 1

11

D001

4 3

2

AF-102

16

1

2

3

MS-275 BOARD(SIDE A)
LND251 12

10

A C251

CN252

BT251

+
11

D251

CL257 CL251
MS-275 >EP GW < 1-867-122-

LITHIUM BATTERY (SECONDARY)

1

FB254 FB253 FB251

CL262 + CL256
R253 FB252

MEMORY STICK CONNECTOR

R251

C252

1-867-122-

11
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

DSC-H1 4-47 4-48

1-867-129>PI<

B

AF LED

(LENS COVER OPEN)
1

4

3

5

MS-275 BOARD(SIDE B)
CN251
12 1

1-867-122-

11

AF-102/MS-275

Ver 1.1 2005. 09
· Refer to page 4-45 for common note for printed wiring board.

·

: Uses unleaded solder.

CD-576 BOARD(SIDE A)
4
14

Note:IC101 is not included in this COMPLETE of CD-576 board

CD-576 BOARD(SIDE B)

3

1 2

1

A

1

A
C101 R106 6
C103 C102

IC101

4

IC102
1 3

C107
15 28

B

5 6 7

7
C105 C109 R109
R104 R105 R110 C108

B
Q104
312 1 2 38

Q102
312

CN101
39

R108

1-867-12116

11

1-867-121-

11
16

1

2

3

3

2

1

EV-016 FLEXIBLE BOARD
1 LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 LND012 LND013 LND014 LND015 LND016 LND017 LND018 LND019 LND020 LND021 LND022 22

20

21

CN001

D001

A

K >PI< EV-016 1-867-1281-867-12811

2

16

1

2

3

1

4

DSC-H1 4-49 4-50

CD-576/EV-016

Ver 1.1 2005. 09
· Refer to page 4-45 for common note for printed wiring board.

·

: Uses unleaded solder.

ST-123 BOARD(SIDE A)
LND004 LND005 LND003 R004 R002 R003 C002

ST-123 BOARD(SIDE B)
C004 IC001
17 R001 8 9 C003 5 12 13 54 1 16 4 3

ST-123 >EP GW< 1-867-123-

1

Q001

8

4

5

1

K

C005

C001

T001

A

L001

1

6

1

12

2

A

D001

A
2

CN001

1-867-1231-867-12316

11

11

1

2

3

4

4

3

2

1

16

PL-039 BOARD (SIDE A)
1-867-124PL-039

PL-039 BOARD (SIDE B)
1 6

ST-124 FLEXIBLE BOARD
D001
LND002
>PI<

CN301
PL-039

D302
C301

C002

C003 R002 LND003

LND001 R001

1-867124-

D301
S301

2

RY301

1

(FLASH POP UP)

LND006 2 1

ST-124-

L001

3 LND004

LND005

1-867-127-

11

1-867-124-

11

DSC-H1 4-51 4-52

>EP GW<

1-867-124-

11

ST-123/PL-039/ST-124

· Refer to page 4-45 for common note for printed wiring board.

·

: Uses unleaded solder.

SW-447 BOARD
20

CN451
1

A
DISP
3 S451 1 2 1 4 3 S454 2 1

LEFT
4 3

MENU
4 S452 2

3 SE402

1 1 5 S459 2 3
C411 C415 R410 R409 C413 C410 C407

2

(YAW SENSOR)
4 C401 A + C402 A +

DOWN
3 4 S458 1
R456 R454

SET
3 S457 2 1 2 1 4 3

UP
4 S456 2

C416 +
L401

6

4

R408 A
C414 R403R404 R407 C404 R406

ZOOM W
11

20

B
DUST
3 S453 1 2 4

IC0401
1 1
C412

ZOOM T
5 S455 2

D451

D452
312

RIGHT
(PITCH SENSOR)
3 S460 1 2 4 R412
4

10 C405 R401

3

R457

R455

R411

SE401

C409

Q401

C403 R402

312

R405

R453

3 2 8

6

4

C406

Q402

3 12

RB452 1 7

2

1

RB451

D455

K

C
16

C408

CN452
6 1

8

7

1-867-125-

11

A

1

2

2

1

3

4
Printed wiring board of the CH-169 and SY-127 board are not shown. Pages from 4-55 to 4-60 are not shown.

DSC-H1 4-53 4-54

SW-447

4-3. PRINTED WIRING BOARDS

4-4. WAVEFORMS

CD-576 BOARD (CAMERA MODE)
1 IC101 1-5,7-9,qa 6 IC101 qj

7.7 Vp-p 265 us 74 ns

4.6 Vp-p

2 IC101 6

7 IC101 qk,ql,wj,wk

7.7 Vp-p 4.4 Vp-p 265 us 74 ns

3 IC101 q;

7.7 Vp-p

265 us

4 IC101 qs-qf

7.7 Vp-p 265 us

5 IC101 qg

1.8 Vp-p 265 us

Waveforms of the SY-127 board are not shown. Page 4-62 is not shown.

DSC-H1 4-61

CD-576

4-3. PRINTED WIRING BOARDS

4-5. MOUNTED PARTS LOCATION
CD-576 BOARD
* C101 * C102 * C103 * C105 * C107 * C108 * C109 A-1 A-1 A-1 B-3 B-1 B-3 B-3

no mark : side A * mark : side B

SW-447 BOARD
C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C415 C416 B-3 B-3 C-4 B-3 B-4 C-3 B-4 C-3 C-3 B-4 B-3 C-4 B-4 B-3 B-4 B-3

* CN101 B-1 IC101 * IC102 * Q102 * Q104 * * * * * * R104 R105 R106 R108 R109 R110 A-3 A-1 B-3 B-2 B-3 B-3 A-1 B-2 B-2 B-3

CN451 A-3 CN452 C-4 D451 D452 D455 B-1 B-1 C-1

IC0401 B-4 L401 Q401 Q402 R401 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R453 R454 R455 R456 R457 B-3 C-3 C-2 C-4 C-4 B-3 B-3 B-3 B-3 B-3 B-3 B-4 B-4 B-2 B-3 C-1 B-1 C-1 B-1 C-1

RB451 C-2 RB452 C-4 S451 S452 S453 S454 S455 S456 S457 S458 S459 S460 SE401 SE402 A-1 A-3 C-1 A-2 B-4 B-2 B-2 B-1 A-4 C-2 C-3 A-3

Mounted parts location of the SY-127 board are not shown. Page 4-64 is not shown.

DSC-H1 4-63E

CD-576/SW-447

NOTE

5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.

Link

EXPLODED VIEWS

H

D I

C

OVERALL SECTION

LCD/CABINET(REAR) SECTION

MAIN SECTION

EVF SECTION

B

A

E F G

LENS SECTION

CABINET(FRONT) SECTION

ST SECTION

Link
AF-102 Flexible BOARD MS-275 BOARD ST-124 Flexible BOARD

ELECTRICAL PARTS LIST
A D G

ACCESSORIES
C F I

CD-576 BOARD PL-039 BOARD SW-447 BOARD

B E H

EV-016 Flexible BOARD ST-123 BOARD SY-127 BOARD

DSC-H1

5. REPAIR PARTS LIST

NOTE: · -XX, -X mean standardized parts, so they may have some differences from the original one. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · CAPACITORS: uF: µF · COILS uH: µH · RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable · SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD...

When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

· Abbreviation CND : Canadian model HK : Hong Kong model AUS : Australian model CH : Chinese model KR : Korea model JE : Tourist model J : Japanese model

Language that can be selected about SY-127 board
Simplified Chinese Traditional Chinese Japanese Swedish Korean Portugal German Spanish Russian

English

French

GP1 GP2

J US CND AUS Vietnam AEP UK E AR BR TW JE HK CH KR

z

z z

z z

z

z

GP3

z z z z z z

GP4

z

z

z

z

z

z

GP5

z

z

z

z

z

Arabic Dutch

Italian

Area

z z z

z

DSC-H1 5-1

5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
5-1-1. OVERALL SECTION

Cabinet (front) section (See page 5-8) E

1
Lens section (See page 5-7)
B C D

D A B C

A

3 2
LCD section, Cabinet (rear) section (See page 5-4)

4
-12 SY 7

2 2
Main section (See page 5-5)

1

2

E

1

1

Ref. No. 1 2 3 4

Part No. 3-056-233-21 3-080-204-11 A-1119-330-A 1-830-604-11

Description SCREW (M2), LOCK ACE, P2 SCREW, TAPPING, P2 SW-447 BOARD, COMPLETE CABLE, FLEXIBLE FLAT (SW-006)

DSC-H1 5-3

5. REPAIR PARTS LIST
5-1-2. LCD SECTION, CABINET(REAR) SECTION
ns : not supplied

51 60 58

55
LED901

52
ns

53
LCD901

59

ns

56

57

54

Ref. No. 51 52 53 54 55

Part No. 3-080-204-11 2-629-828-01 2-629-831-01 2-629-769-01 2-629-767-01

Description SCREW, TAPPING, P2 SHEET METAL (L), STRAP LID, DC WINDOW, LCD EYE CUP

Ref. No. 56 57 58 59 60

Part No. 2-629-833-01 2-629-834-01 X-2055-957-1 X-2055-956-1 2-629-835-01

Description SHEET, LCD ADHESIVE LID, JK FRAME ASSY, LCD CABINET (REAR) ASSY BRACKET (L), STRAP

LCD901 8-753-229-36 ACX336AK-3 LED901 1-479-015-11 BLOCK, LIGHT GUIDE PLATE (2.5)

DSC-H1 5-4

Ver 1.1 2005. 09

5. REPAIR PARTS LIST
5-1-3. MAIN SECTION
ns : not supplied

EVF section (See page 5-6)

102
ns BT901 BT251

103

MS -

27

5

107 108

ns

104 110 109 7
(Note)

101

-12 SY

103

SP901

105
: BT251 (Lithium battery) MS-275 board on the mount position. (See page 4-48)

106

Note : Refer to the table of page 5-1 about language of SY-127 board.
Ref. No. 101 102 103 104 105 106 107 108 109 109 Part No. X-2055-945-1 A-1119-327-A 3-080-204-11 1-830-602-11 2-629-768-01 2-630-230-01 2-629-759-01 2-629-760-01 A-1127-774-A A-1127-775-A Description HOLDER ASSY, BATTERY MS-275 BOARD, COMPLETE SCREW, TAPPING, P2 CABLE, FLEXIBLE FLAT (MS-029) RETAINER, SP LABEL, FUSE REPLACEMENT CAUTION SHAFT, BT SPRING, BT, OPEN SY-127 BOARD, COMPLETE (SERVICE) (GP1) SY-127 BOARD, COMPLETE (SERVICE) (GP2) Ref. No. 109 109 109 110 SP901 0 BT251 BT901 Part No. A-1127-776-A A-1127-777-A A-1127-778-A X-2059-858-1 1-825-923-41 Description SY-127 BOARD, COMPLETE (SERVICE) (GP3) SY-127 BOARD, COMPLETE (SERVICE) (GP4) SY-127 BOARD, COMPLETE (SERVICE) (GP5) LID ASSY (SERVICE), BT LOUDSPEAKER (1.3CM)

1-756-539-21 BATTERY, LITHIUM SECONDARY 1-780-267-11 TERMINAL BOARD, BATTERY

Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

DSC-H1

5-5

5. REPAIR PARTS LIST
5-1-4. EVF SECTION

156 157

LCD902

155

154

153

152 151

Ref. No. 151 152 153 154 155

Part No. A-1119-332-A 3-089-447-01 3-089-448-01 3-089-445-01 3-089-446-01

Description EV-016 BOARD, COMPLETE GUIDE, LAMP CUSHION, LB ILLUMINATOR SHEET, PRISM

Ref. No.

Part No.

Description

156 X-2055-959-1 HOLDER ASSY, LCD 157 X-2055-958-1 LENS ASSY, VF LCD902 8-753-233-08 LCX067AKEB-1

DSC-H1 5-6

5. REPAIR PARTS LIST
5-1-5. LENS SECTION

207 201 206

208
IC101
76

209
-5

CD

204

210

202 205 205

203

Ref. No. 201 202 203 204 205

Part No. A-1127-773-A 2-631-861-01 2-629-774-01 2-629-773-01 3-078-890-21

Description OPTICAL UNIT (B173A) (SERVICE) SHEET (CD) HEAT SINK, CCD FRAME, LENS SCREW, TAPPING

Ref. No. 206 207 208 209 210 IC101

Part No. 2-592-605-01 1-788-298-11 2-592-693-01 A-1119-326-A

Description

RUBBER (TM), SEAL OPTICAL FILTER BLOCK PLATE (T), LIGHT INTERCEPTION CD-576 BOARD, COMPLETE (IC101 is not included in this COMPLETE board.) 1-867-126-11 FP-224 FLEXIBLE BOARD A-1122-935-A CCD BLOCK ASSY (CCD IMAGER) (IC101 is not included in this COMPLETE board of CD-576.)

Be sure to read "Precautions upon replacing CCD imager" on page 4-1 when changing the CCD imager.

DSC-H1 5-7

5. REPAIR PARTS LIST
5-1-6. CABINET(FRONT) SECTION
ns : not supplied

ST section (See page 5-9)
B

259
A

256 260 253

ns

258

B

ns

259
MIC901

261 252
ns

259

254 259

251

257 255 259

259

ns
A

262
Ref. No. 251 252 253 254 255 Part No. X-2055-951-1 2-629-813-01 2-629-815-01 2-629-812-01 2-629-783-01 Description CABINET (FRONT) ASSY PLATE, ORNAMENTAL GRIP SHEET METAL (R), STRAP SCREW, TRIPOD Ref. No. 256 257 258 259 260 Part No. 1-830-603-11 2-629-781-01 1-479-260-11 3-080-204-11 2-629-820-01 Description CABLE, FLEXIBLE FLAT (ST-001) PLATE (LENS), FRONT GROUND SWITCH BLOCK, CONTROL (SW51780) SCREW, TAPPING, P2 RING (W), LENS

261 2-629-817-01 HOLDER, MICROPHONE 262 A-1119-333-A AF-102 FLEXIBLE BOARD, COMPLETE MIC901 1-542-446-81 MICROPHONE

DSC-H1 5-8

Ver. 1.3 2006. 06

5. REPAIR PARTS LIST
5-1-7. ST SECTION

306 303 304
Blue White

301

Red

309 308 310

RY301

307

305

302

PRECAUTION DURING SOLENOID PLUNGER INSTALLATION
6 5