Text preview for : Sony STR-DE635 ver 1.1.PDF part of Sony STR-DE635 Service Manual
Back to : Sony STR-DE635 ver 1.1.pa | Home
STR-DE635
SERVICE MANUAL
Ver 1.1 2002. 02
US Model Canadian Model AEP Model
Manufactured under license from Dolby Laboratories Licensing Corporation. "DOLBY" and the double-D symbol a are trademarks of Dolby Laboratories Licensing Corporation.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS: POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 loads, both channels driven, from 20 20,000 Hz; rated 80 W per channel minimum RMS power, with no more than 0.09% toral harmonic distortion from 250 mW to rated output (USA model only). Amplifier section Stereo mode USA, Canadian models: (8 20Hz 20kHz, THD 0.09%) 80W + 80W AEP model: (4 DIN, 1kHz) 70W + 70W Surround mode USA, Canadian models: (8 at 1kHz, THD 0.8%) Front: 80W + 80W Centera): 80W Reara): 80W + 80W AEP model: (4 DIN, 1kHz) Front: 70W + 70W Centera): 70W Reara): 70W + 70W a) Depending on the sound field settings and the source, there may be no sound output. Dynamic power output 145W + 145W, 8 210W + 210W, 4 Frequency response PHONO: RIAA equalization curve ±0.5 dB USA, Canadian models: CD, MD/TAPE, DVD/LD, TV/SAT, VIDEO1,2: AEP model: CD, MD/TAPE, DVD, TV/LD, VIDEO1,2: 10Hz 50kHz + 0.5/2dB (with sound field, equalizer, and bass boost bypassed) PHONO: Sensitivity: 2.5mV Impedance: 50k S/Nb): 86dB (A, 2.5mVc)) USA, Canadian models: 5.1CH INPUT, CD,DVD/LD,MD/TAPE,TV/ SAT,VIDEO1,2: AEP model 5.1CH INPUT, CD,DVD,MD/TAPE,TV/ LD,VIDEO1,2: Sensitivity: 150mV Impedance: 50k S/Nb): 96dB (A, 150mVc))
Inputs (Analog)
b) Input short c) Weighted network, input level
-- Continued on next page --
FM STEREO FM-AM RECEIVER
9-928-897-12
2002B1600-1 © 2002.02
Sony Corporation
Home Audio Company Published by Sony Engineering Corporation
Inputs (Digital)
Outputs
BASS BOOST Sampling Frequency EQ
DVD/LD (coaxial): Sensitivity: Impedance: 75 S/N: 100dB (A, 20kHz LPF) DVD/LD (Optical): Sensitivity: Impedance: S/N: 100dB (A, 20kHz LPF) MD/TAPE, (REC OUT); VIDEO1,2 (AUDIO OUT): Voltage: 150mV, Impedance: 10k SUB WOOFER: Voltage:2V Impedance: 1k PHONES: Accepts low-and high-impedance headphones +6dB at 70Hz 48kHz BASS: 100Hz 1.0kHz (21steps) MID: 500Hz 5.0kHz (21steps) TABLE: 1.0kHz 10kHz (21steps) Gain levels: ±10dB, 1dB step
AM tuner section Tuning range USA, Canadian models: With 10-kHz tuning scale: 530 1,710kHzd) With 9-kHz tuning scale: 531 1,710kHzd) AEP model 531 1,602kHz Antenna Loop antenna Usable sensitivity 50dB/m (at 1,000kHz or 999kHz) S/N 54dB (at 50mV/m) Harmonic destortion 0.5% (50mV/m, 400kHz) Selectivity At 9kHz: 35dB At 10kHz: 40dB d) You can change the AM tuning scale to 9kHz. After tuning in any AM station, turn off the receiver. Hold down the TUNING+ button and press the 1/u button. All preset stations will be erased when you change the tuning scale. To reset the scale to 10kHz, repeat the procedure. Video section Inputs Outputs General System
1Vp-p 75 1Vp-p 75
FM tuner section Tuning range Antenna terminals Sensitivity
87.5 108.0MHz 75, unbalanced Mono: 18.3dBf, 2.2µV/75 Stereo: 38.3dBf, 22.5µV/75 Usable sensitivity 11.2dBf, 1µV/75 S/N Mono: 76dB Stereo: 70dB Harmonic destortion at 1kHz Mono: 0.3% Stereo: 0.5% Separetion 45dB at 1kHz Frequency response 30Hz 15kHz + 0.5/2dB Selectivity 60dB at 400kHz
Tuner section: PLL quartz-locked digital synthesizer system Preamplifier section: Low-noise NF type equalizer Power amplifier section: Pure-complementary SEPP Power requirements USA, Canadian models: 120V AC, 60Hz AEP model 230V AC, 50/60Hz Power consumption USA: 270W Canada: 285VA AEP: 200W AC outlets USA, Canadian models: 2switched, total 100W AEP model 1switched, max 100W Dimensions 430 × 364 × 157.5mm (17 × 145/16 × 61/4 in.) including projecting parts and controls Mass (Approx.) USA, Canadian models: 9.5kg (20 lbs. 15 oz.) AEP model 10.1kg Supplied accessories FM wire antenna (1) AM loop antenna (1) Remote commander RM-PP402 (remote) (1) R6 (size-AA) batteries (2) FM antenna adapter (1) Design and specifications are subject to change without notice.
--2--
TABLE OF CONTENTS SAFETY CHECK-OUT
(US model only) After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
1. GENERAL ·········································································· 4 2. SERVICEING NOTE ······················································· 6 3. TEST MODE ······································································ 6 4. DIAGRAMS
4-1. 4-2. 4-3. 4-4. 4-5. 4-6. 4-7. 4-8. 4-9. 4-10. 4-11. 4-12. 4-13. 4-14. 4-15. 4-16. 4-17. 4-18. 4-19. 4-20. 4-21. 4-22. 4-23. Block Diagram Main Section ··········································· 7 Block Diagram Power Section ········································· 9 Circuit Board Location ····················································· 11 Schematic Diagram Digital Section(1/3) ······················· 13 Schematic Diagram Digital Section(2/3) ······················· 15 Schematic Diagram Digital Section(3/3) ······················· 17 Printed Wiring Board Digital Section(1/2) ····················· 19 Printed Wiring Board Digital Section(2/2) ····················· 21 Printed Wiring Board Display Section ··························· 23 Schematic Diagram Display Section ······························ 25 Printed Wiring Board Surround Section ························· 27 Schematic Diagram Surround Section ··························· 29 Printed Wiring Board Rear AMP Section ······················· 31 Schematic Diagram Rear AMP Section ························· 33 Printed Wiring Board Power Section ····························· 35 Schematic Diagram Power Section ································ 37 Printed Wiring Board Video Section ······························ 39 Schematic Diagram Video Section ································· 41 Printed Wiring Board Main Section ······························· 43 Schematic Diagram Main Section(1/2) ·························· 45 Schematic Diagram Main Section(2/2) ·························· 47 IC Pin Function ································································ 49 IC Block Diagrams ··························································· 59
LEAKAGE
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instruments. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)
2.
3.
To Exposed Metal Parts on Set
5. EXPLODED VIEWS
5-1. Front Panel Section ·························································· 62 5-2. Chassis Section ································································· 63
0.15µF
1.5k
AC voltmeter (0.75V)
6. ELECTRICAL PARTS LIST ······································· 64
Earth Ground Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
--3--
SECTION 1 GENERAL
Identifying the Parts Front Panel
1 2 3 4
1/u switch Function buttons INPUT MODE button 5.1CH INPUT button
5 6 7
MASTER VOLUME control MUTING button SPEAKERS selector PHONES jack
8 9 0
!¡ !TM !£ !¢
DISPLAY button DIMMER button A.F.D button/indicator MODE button/indicator 2CH button/indicator MULTI CHANNEL DECODING indicator BASS BOOST button EQUALIZER button DIRECT button SHIFT button Numeric buttons (0 to 9) AM button (US, Canadian models) RDS EON button (US, Canadian models) FM button (US, Canadian models) AM/FM button (AEP model) FM MODE button MEMORY button
! !§ !¶ !· !ª @º @¡ @TM @£ @¢
TUNNIG +/- buttons PRESET +/- buttons LEVEL button SUR button EQ button Cursor buttons() Jog dial SET UP button NAME button ENTER button RDS PTY button (AEP model)
--4--
SECTION 2 SERVICING NOTE
Rear Panel 1. When the front panel is removed, the VR board is removed at the same time. Consequently the LEDs cannot be turned on and the sound volume cannot be increased or decreased from the remote control. 2. When servicing the DIGITAL board, be sure to connect the earth land of the DIGITAL board with the chassis frame so that the earth potential of the DIGITAL board must not be floated from the chassis frame.
1
2
3
4
5
6
7
SECTION 3 TEST MODE
8
FLUORESCENT INDICATOR TUBE TEST MODE
* All fluorescent segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another. * Procedure: While depressing the ENTER, the LEVEL and the EQ buttons simultaneously, press the power [1/u] button to turn on the main power. All segments turn on at the same time, then each segment turns on press the ENTER button..
DSP TEST MODE
* It tests whether the DSP works correctly or not. When the DSP test is activated, the test data is output from the DSP (IC1401: CXD2712R) of the DIGITAL board and is written in the RAM (IC1402: IDT71V016S). When the test data is read from the RAM by the DSP, the data output must be equivalent to the original data. If they disagree, an error is triggered. Errors can be caused by the broken data line or defective soldering. * Procedure While pressing the SETUP, LEVEL and SUR buttons, press the POWER button to enter the DSP test mode. The message DSP TEST MODE appears. When an error occurs, the message DSP2 ERROR is displayed. When there is no error, the message DSP2 NO ERROR appears and the 1 kHz signal is output to all channels. Then, the mode can be switched the (SIGN WAVE) (THROUGH) and (INPULSE) mode.
!ª !·
!¶
!§
! !¢
!£
!TM
!¡
0
9
FACTORY SET MODE
* All preset contents are reset to the default setting. * Procedure: While depressing the SET UP, the LEVEL and the ENTER buttons simultaneously, press the power [1/u] button to turn on the main power. The message Factry Set appears and the present contents are reset to the default values.
1 2 3 4 5 6 7 8 9 !º
ANTENNA DIGITAL 5.1 CH INPUT SPEAKERS (FRONT) SPEAKERS (REAR) SPEAKERS (CENTER) WOOFER INPEDANCE SELECTOR AC power cord AC OUTLET
!¡ !TM !£ !¢ ! !§ !¶ !· !ª
S-LINK VIDEO 1 VIDEO 2 DVD/LD (US, Canadian models) DVD (AEP model) TV/SAT (US, Canadian models) TV/LD (AEP model) MONITOR MD/TAPE CD PHONO
AUTOBETICAL MODE (AEP Model only)
* This mode is installed in the Europe models only. When this mode is used, the receiver scans the broadcasts that can be received by tuner, and sets up the broadcasts. Be sure to start scanning after connecting the antenna. Procedure: Check that the antenna is connected. Press the POWER button while pressing the MEMORY button to turn on the power. The message "Autobetical select" appears and scanning starts by tuner.
ALL CLEAR MODE
* All preset contents are cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. * Procedure: While depressing the SET UP button simultaneously, press the power [1/u] button to turn on the main power. The machine enters the DEMO mode.DEMO mode: Wait a while, then the demonstration starts. If the power [1/u] button is pressed often the demonstration has started, the power is turned off, and the demonstration resumes if the power [1/u] button is pressed again. ALL CLEAR mode; If the power [1/u] button is pressed often the machine enters the DEMO mode, but before the demonstration starts, the display is turned off. Press [1/u] again. No response is returned. The press [1/u] again. The preset data is cleared and the machine enters the normal power-on state.
VERSION MODE
* When this mode is used, the microprocessor version number is displayed. * Procedure: Press the POWER button while pressing the ENTER, LEVEL, and SUR buttons to turn on the power. The microprocessor version number appears as follows.
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. * Procedure: While depressing the SOUND FIELD MODE button, press the power [1/u] button to turn on the main power. The message S.F Initialize appears and initialization is performed.
AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE (US, Canadian models)
* Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. * Procedure: Set the FUNCTION to AM. Turn off the main power. While depressing the TUNING+ button or the PRESET TUNING + button, press the power [1/u] button to turn on the main power. Either the message AM 9kHz Step or AM 10kHz Step appears. Select the desired step.
--5--
--6--
STR-DE635
SECTION 4 DIAGRAMS
4-1. BLOCK DIAGRAM MAIN SECTION
TUNER UNIT
ANT LEVEL 6 RDS IC1 13 FM AM L OUT 10
STEREO T. MUTE
ANT LEVEL 2 16 14 AUDIO SELECT IC301 US,Canadian MODEL 4 R CH 3 2 8 9 VIDEO2 INPUT OUTPUT VIDEO1 INPUT CONTROL
CLK
RDS DATA RDS CLK
FM DET 9 TM301 ANTENNA FM 75 AM
4
A
SELECTOR IC1502 19 2CH L J305 INPUT INPUT OUTPUT L L L J304 L L L 24 22 21 CONTROL
CLK CE
X1 4.33MHz AEP ONLY
SELECTOR IC303 27 26 25 23
IC304 IC1510 AUDIO CODEC IC1503 IC1504 IC1504 30 LIN+ 29 LIN9 SDTO 20 39 MCLK1 4 BCLK 5 LRCK 17
IC1403
5
TV/SAT DVD/LD
L OUT 17 MUTE Q1502 IC1508 C OUT 25 MUTE Q1506 IC1508 IC1507 W OUT 4 21 L IC1505 MUTE Q1505 27 C IC1505 LS OUT 22 2 W IC1506 MUTE Q1504 24 LS IC1509
L
TUNED
R OUT 12
DATA CLK CE
DO
C
4 14 15 13
2
S DATA
3
S CLK
1
S LAT
STEREO
MUTING
TUNED
DO
6 11 10 12
W
L OUT1 27 L OUT3 23 R OUT3 24 L OUT2 25
J301 PHONO CD L L
EQ AMP IC302
AUDIO DSP IC1401 113 BCK0
IC1403
SL
B
114 BCK1 115 LRCK0 116 LRCK1
SOA 2 SOB 3 SOC 4
6 SDTI 1 7 SDTI 2 8 SDTI 3
DI
CE
TV/LD DVD
DI
J302 INPUT MD/TAPE OUTPUT L L
15 14 16
15 14 16
S DATA
S DATA
S CLK
S LAT
S CLK
S LAT
AEP MODEL
CDTO
DOLBY DIGITAL AUDIO DECODER IC1301
IC1403
CCLK
CDTI
DFS
15 14 16
S DATA S CLK S LAT
PD
CS
AUDATA0 24
IC1403
117 SIA 118 SIB
IC1403
DATA CLK LAT
44 43 42 41 17 11
DIGITAL AUDIO I/F RECEIVER IC1101 DATA 16 CK OUT 13 5 6 IC007 SELECT SWITCH IC1005 IC1006 7 3 D IN BCK 14 LRCK 15 10 11 12 12.288M 22 IC1404 A B 36 DI 38 CLK 37 CE 33 BP SYNC ERROR 34 DO 35 AUTO 32
CSFLAG XSTATE XMODE
AUDATA1 23 84 SDIA0 AUDATA2 22 85 SDIA1
119 SIC
IC001 OPT DVD IR LINK DET J001 COAXIAL DVD
D0-7 83 SDBCK0 82 SDWCK0 74 XWE IC11404 IC1404 8 XI D0-7 X3501 12.288MHz 70 XOE 16 20 HD0 . 23 HD7 25 15 HA0
XHDWR
CLKI 99 X1401 10MHz CLKO 100
SRAM IC1402
A0-7 · RCH is omitted · Signal Path : FM : PHONO SOD 5 HRDY 13
XHDCS
A 14 9 B 2
: CD
: DVD
9 14
SCK CS IC SI
26
Q1201 Q1202
IC1202
48 25 17 Q1204 J201 MONITOR OUTPUT INPUT VIDEO 1 OUTPUT 15 V1 OUT 58 59 60 84
STEREO TUNER MUTE AUTO STOP DATA
69 68 66 Q1102
62
IC1202
XRST
SO 67
Q1507 MUTE CONT
VIDEO SELECT IC201 1 M OUT 13 V1 IN VEE 8 3 VCC 16 IC202 -5V REG 2 -15V +5V
STEREO TUNED TMUTE DO S CLK S DATA S DATA S CLK S LAT S LAT
Q1203 D1203
D1202 D0-7 A B
56 57 55
CLOCK LATCH DATA
108 107
DIG IN A DIG IN B
47 48 46
EV CLK EV STB EV DATA
112 110 111 115
DI CL CE BY SYNC
109 117 118
XMODE CSFLAG XSTATE
116 113 114
ERROR AUTO DO
106
ANALOG/DIG
85
S MUTE S MUTE
1
SCCLK
2
SI
4
CS
5
IC
3
SO
24 17 HD0 HD7
25
HA0
13 16
XHDWR XHDCS
26
XRST
27 15
HRDY SOD
30 31 29 28 32 35
CCLK CDTO PD CS 96kHZ CDTI
J202 INPUT VIDEO 2 OUTPUT US,Canadian MODEL TV/SAT DVD/LD AEP MODEL TV/LD DVD INPUT INPUT 11 V2 OUT SW2 10 SW3 4 3 TV 5 LD SW5 2 SW4 6 9 V2 IN SW1 14
AC MUTE 82 PROTECT 66 RY HP 104 RY FRONT A 99 RY FRONT B 100 RY CENTER 101
AC MUTE PROTECTOR HP RY SP/A RY SP/B RY RY CENTER RY WOOFER REAR SP RY
77 VIDEO(SW1) 76 VIDEO(SW2) 75 VIDEO(SW3) 72 VIDEO(SW4)
C
J203
RY WOOFER 103 RY REAR 102
D201
SYSTEM CONTROL IC1201 DISP DATA 50 DISP CLK 52 DISP MR 49 SREQ 51 RESET 90 RY POWER 105 STOP 67 SOTO 10 SINO 9 MD2 87 XI 93 XO 92 MD0 89 D1201 U DATA U CLOCK U MREQ U SREQ U REST RESET RY POWER STOP SOT0 SIN1 MD2 MD0
D
X1201 16MHz
16
--7--
--8--
STR-DE635
Ver 1.1 2002. 02
4-2. BLOCK DIAGRAM POWER SECTION
POWER AMP(L) IC501 +VDD VOLUME RV401 L IC408 DATA CLK LAT -VDD VOL CONT IC414 14 IN 9 DATA 8 CLK 10 LAT VOL CONT IC416 3 IN OUT 2 +VDD W IC410 14 IN DATA CLK LAT 9 DATA 8 CLK 10 LAT VOL CONT IC415 14 IN DATA CLK DATA CLK LAT +VDD LAT 9 DATA 8 CLK 10 LAT POWER AMP(SL) IC701 13 VCC 14 VCC +VE 2 15 VEE BOOSTER Q706 -15V Q120 LED DRIVE 1 MUT -VE AC MUTE MUTE Q501,503 3 BOOSTER Q707 CUR DET Q798 6 IN NF 5 Q704, Q705 BIAS RY701 AF DETECTOR Q709,710 RELAY DRIVE Q745 +32V 3 OUT 15 1 MUT +VE 6 IN -VE 2 3 RY681 RELAY DRIVE Q681 JJ103 WOOFER +5V 1 IC404 +5V REG 3 IC401 +15V 3 +15V REG IC402 -15V REG 2 1 T901 -VE 11 BOOSTER Q607 CUR DET Q698 AF DETECTOR Q609,610 OUT 15 8 IN NF 9 Q604, Q605 BIAS Q611 RY601 RELAY DRIVE Q645 -VDD POWER AMP(C/W) IC601 13 VCC 14 VCC 15 VEE +VE 12 BOOSTER Q606 RELAY DRIVE Q596 C S(L) S(R) R CH TM701 SURROUND SPEAKER S801 IMPEDANCE SELECTOR 4 8 1 MUT -VE 3 BOOSTER Q507 CUR DET Q598 AF DETECTOR Q509,510 RY501 RELAY DRIVE Q546 RY502 OUT 15 6 IN NF 5 Q504, Q505 BIAS Q511 13 VCC 14 VCC 15 VEE +VE 2 BOOSTER Q506 RELAY DRIVE Q601 RY602 R CH J701 PHONES
L A R L B R CH R :CD TM501 FRONT SPEAKER · R-CH is omitted due to same as L-CH. · Signal Path
:FM
C
IC410
B
SL
IC409
M
-VDD
Q801 +32V REG D801 F801
+VDD PROTECTOR Q547-549 F802 D802-805 SWITCH Q613 F803
PROTECTOR -VDD RY HP SP/A RY SP/B RY RY CENTER RY WOOFER RY REAR IC1207 DIGITAL PWB FROM SUFFIX-12 DISP +5V 3 +5V REG IC1501 RY POWER STOP RESET URESET USREQ UMREQ D151,152 D154-170 DIGITAL +5V 3 CODEC +5V 3 +5V REG IC1203 +3.3V 1 REG IC1204 CONT µCOM ETC D100,101,104-106 RV101 7.9 15 . 20 D1208 DISP µCOM+5.6V D1209 X101 16MHz IC101 Q101 SIRCS 26 REMOTO CONTROL RECEIVER D1211 URESET 58 IC105 2 4 MOTOR DRIVE 5 8 6 VOLUME 55 UP
AD KEY1 AD KEY2 AD KEY3 AD KEY4 AD KEY5 AD KEY6 AD KEY7 SP A SP B
C
+24V F804
D806-809 1
F805
1
F2 F1
D
UCLOCK UDATA SOTO SIN1 MD2 MD0 3
+5V REG IC1205
1
1
29
3
+6.2V REG
1 RY901 RELAY DRIVE Q901
F901
LED DRIVER IC106 16 17 18 19 49 51 20 19
MD0 MD2 SINO
AEP MODEL F903
61 62 60 58
UCLOCK UMREQ URESET UDATA
59
USREQ
75 76
JOG UP JOG DOWN
1
DCS
2
EQ
3
B.B
4
MUTE
5
D.D
88 87 89 90
LED CLK LED CE LED CLR LED DATA
82
XO
83
XI
7
POWER RY
RDS DATA
54 RDS DATA 53 RDS CLK 46 RDS SIGNAL
A
RDS CLK ANT LEVEL
SOTO
MODE CONTROL IC102
POWER KEY ABUS A1 IN ABUS OUT
+6.2 REG Q1205 T902 3 D901-904 JW927
US,Canadian MODEL JW925
CNJ901 AC OUTLET
RESET 77
FL CLEAR
RESET Q108
FL CLK
56 DOWN
FL LAT
FL DAT
STOP 47
8
RESET IC1206 6
5
JW928
38
39
40
41
43
44
44
64
65
66
21 24 25
82
67
63
CNP901 AC IN
FUNCTION KEY S101,104,107 S140-144
FUNCTION KEY S102,105,108 S110-114
FUNCTION KEY S103,106,109 S115-119
FUNCTION KEY S120-126
FUNCTION KEY S127-133
FUNCTION KEY S134-139
FUNCTION KEY S145-149
SPEAKER SWITCH S151 S150 POWER 34 26 24
CLR CLK LAT
29 4
LS CLK
5 30
DIN CL
Q109 I/O BUFFER
J204 S-LINK
DIN 29 IC103 FL DRIVE F2
3 DOUT IC104 FL DRIVE F1
FL101 FLOURESCENT INDICATOR TUBE
--9--
-- 10 --
STR-DE635
4-3. CIRCUIT BOARD LOCATION
4/8 board AC board
SP board
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this necessary note is printed in each block.)
For schematic diagrams. Note:
VIDEO board
· All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. · % : indicates tolerance. · 2 : nonflammable resistor. · 1 : fusible resistor. · C : panel designation.
Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Note: Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
For printed wiring boards. Note:
· X : parts extracted from the component side. ® : Through hole. · · b : Pattern from the side which enables seeing.
DC board DISPLAY board
DIGITAL board SP-SW board TUNER board
· Waveform DIGITAL Board
1 IC1201 (TM (XO)
4.0Vp-p
H.P board
· · · · U : B+ Line. V : B Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. No mark : FM Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Circled numbers refer to waveforms. Signal path. F : FM J : CD c : DIGITAL I : PHONO Abbreviation CND :Canadian model
2 IC1401
4MHz
100
SW board LED board JOINT(H) board
(CLKO)
3.5Vp-p
·
ROTARY board VOLUME board REAR AMP board MUTING board
MAIN board
· · ·
10MHz
3
IC1404 25
5.5Vp-p
·
12.288MHz
DISPLAY Board
4 IC102 *TM (XO)
3.6Vp-p
16.0MHz
5 IC12 !§ (X OUT)
3.8Vp-p
7.28MHz
TUNER Board
6 IC1 !£ (X 1)
2.7Vp-p
4.33MHz
-- 11 --
-- 12 --
STR-DE635
4-4. SCHEMATIC DIAGRAM DIGITAL SECTION(1/3)
· See page 19 for Printed Wiring Board. · See page 12 for Waveforms. · See page 49 for IC Pin Functions.
-- 13 --
-- 14 --
STR-DE635
Ver 1.1 2002. 02
4-5. SCHEMATIC DIAGRAM DIGITAL SECTION(2/3)
· See page 19 for Printed Wiring Board. · See page 12 for Waveforms. · See page 51 for IC Pin Functions. · See page 60 for IC Block Diagrams.
CXD9511Q
DIGITAL PWB FROM SUFFIX-12
-- 15 --
-- 16 --
STR-DE635
4-6. SCHEMATIC DIAGRAM DIGITAL SECTION(3/3) · See page 19 for Printed Wiring Board. · See page 54 for IC Pin Functions. · See page 60 for IC Block Diagrams.
-- 17 --
-- 18 --
STR-DE635
4-7. PRINTED WIRING BOARD DIGITAL SECTION(1/2) · See page 11 for Circuit Boards Location.
1 A
2
3
4
5
6
7
8
9
10
11
12
13
14
B
C
D
E
F
G
H
· Semiconductor Location
Ref. No. D1001 D1101 D1102 D1208 D1209 D1211 D1501 D1504 D1505 IC1005 Location E-2 C-3 C-6 A-9 D-12 A-9 F-11 G-11 H-11 D-2 Ref. No. IC1007 IC1101 IC1102 IC1201 IC1202 IC1301 IC1401 IC1402 IC1403 IC1404 IC1502 Location E-2 C-2 C-6 C-7 F-6 C-4 F-5 F-3 E-3 D-3 G-10 Ref. No. IC1503 IC1504 IC1505 IC1506 IC1507 IC1508 IC1509 IC1510 IC1554 Q1201 Location F-8 F-10 G-7 G-8 G-9 G-12 F-12 E-12 E-10 E-6 Ref. No. Q1202 Q1501 Q1502 Q1503 Q1504 Q1505 Q1506 Q1507 Location E-6 E-11 F-11 F-11 G-11 G-11 H-11 E-11
-- 19 --
-- 20 --
STR-DE635
Ver 1.1 2002. 02
4-8. PRINTED WIRING BOARD DIGITAL SECTION(2/2) · See page 11 for Circuit Boards Location.
1 A
2
3
4
5
6
7
8
(Page 36)
9
10
DISPLAY BOARD (Page 24)
11
12
39
13
B
44
C
23
D
E
35
36
F
40
G
H
· Semiconductor Location
Ref. No. D1002 D1201 D1202 D1203 D1204 D1205 D1206 D1207 D1210 IC1001 Location C-12 C-7 B-8 B-9 C-2 C-2 C-4 C-4 B-10 D-13 Ref. No. IC1006 IC1203 IC1204 IC1205 IC1206 IC1501 Q1203 Q1204 Q1205 Location C-12 A-3 A-3 C-4 D-5 C-5 B-9 C-8 C-3
43
DIGITAL PWB FROM SUFFIX-12 (Location B-6)
-- 21 --
-- 22 --
STR-DE635
4-9. PRINTED WIRING BOARD DISPLAY SECTION · See page 11 for Circuit Boards Location.
1 A
2
21
3
4
5
6
7
8
9
10
11
12
13
14
(Page 22)
B
(Page 28)
C
27
D
(Page 40)
D108
E
F
27 28
· Semiconductor
Location
Ref. No. D102 D103 D104 D105 D106 D107 D108 D113 D180 Location A-4 B-4 B-3 C-3 C-2 B-13 D-6 D-6 D-6 Ref. No. IC101 IC102 IC103 IC104 IC105 Q101 Q102 Q108 Q109 QQ1 Location C-4 E-8 C-7 B-6 B-2 C-4 E-9 D-9 D-6 C-2
-- 23 --
-- 24 --
STR-DE635
4-10.
SCHEMATIC DIAGRAM DISPLAY SECTION · See page 12 for Waveforms. · See page 56 for IC Pin Functions. · See page 59 for IC Block Diagrams.
AEP MODEL
-- 25 --
D113
EXCEPT AEP
-- 26 --
STR-DE635
4-11.
PRINTED WIRING BOARD SURROUND SECTION · See page 11 for Circuit Boards Location.
1 A
2
3
4
5
6
7
8
9
10
11
12
13
14
AEP
RDS PTY
B
AEP MODEL
RDS ON EXCEPT AEP
C
FM/ AM
AEP MODEL
D
AEP
E
23 28
F
23
· Semiconductor
G
Location
Ref. No. D101 D120 D121 D151 D152 D154 D155 D156 D157 D158 D159 D160 D161 D162 D163 D164 D165 D166 D167 D168 D169 D170 Location I-4 G-11 G-11 B-4 C-5 A-6 C-9 A-4 B-1 D-4 B-6 C-6 C-7 C-8 C-10 B-10 B-9 B-8 B-7 B-6 C-1 A-5
24
H
I
16
-- 27 --
-- 28 --
STR-DE635
4-12.
SCHEMATIC DIAGRAM SURROUND SECTION
-- 29 --
-- 30 --
STR-DE635
4-13.
PRINTED WIRING BOARD REAR AMP SECTION · See page 11 for Circuit Boards Location.
· Semiconductor
Location
Ref. No. D701 D702 D703 D704 D705 D706 D749 D751 D752 D753 D754 D798 D799 IC701 Q704 Q705 Q706 Q707 Q708 Q709 Q710 Q754 Q755 Q756 Q757 Q758 Q798 Q799 Location H-9 H-10 H-10 H-10 F-3 F-4 F-9 G-2 H-2 H-2 H-3 F-11 F-3 G-6 G-10 H-10 H-9 H-11 G-11 F-3 F-4 G-3 H-3 H-2 H-4 G-4 F-11 G-4
1 A
2
3
4
5
6
7
8
9
10
11
12
B
C
D
(Page 43) (Page 43)
E
(Page 44) (Page 43) (Page 44)
F
G
H
I
16
-- 31 --
-- 32 --
STR-DE635
4-14.
SCHEMATIC DIAGRAM REAR AMP SECTION · See page 61 for IC Block Diagrams.
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
-- 33 --
-- 34 --
STR-DE635
4-15.
PRINTED WIRING BOARD POWER SECTION · See page 11 for Circuit Boards Location.
1 A
2
3
4
5
6
7
8
9
10
11
12
13
14
21
B
21
C
D
(Page 44)
E
F
G
16
· Semiconductor
(Page 22)
H
Location
Ref. No. D801 D804 D805 D806 D810 D901 D902 D903 D904 D905 D907 IC399 Q801 Q901 Location B-9 F-2 F-2 A-12 B-12 C-6 C-6 D-6 C-6 B-6 A-5 F-8 B-12 A-5
-- 35 --
-- 36 --
STR-DE635
4-16.
SCHEMATIC DIAGRAM POWER SECTION · See page 12 for Waveforms. · See page 61 for IC Block Diagrams.
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
-- 37 --
-- 38 --
STR-DE635
4-17.
PRINTED WIRING BOARD VIDEO SECTION · See page 11 for Circuit Boards Location.
1
· Semiconductor
2
3
4
5
6
7
8
9
10
11
12
13
Location
Ref. No. D201 D251 IC201 IC202 IC251 IC252 IC253 IC254 IC408 IC409 IC410 Q251 Q252 Q253 Q254 Q255 Q256 Q257 Q258 Location C-4 F-5 C-4 F-6 F-4 F-3 F-3 F-1 H-11 G-11 F-11 G-3 G-3 G-5 F-2 F-2 G-2 G-3 F-3
A
B
C
D
E
(Page 21)
F
MAIN BOARD
(Page 21) (Page 22)
G
H
(Page 23)
I
16
-- 39 --
-- 40 --
STR-DE635
4-18.
SCHEMATIC DIAGRAM VIDEO SECTION
-- 41 --
-- 42 --
STR-DE635
4-19.
PRINTED WIRING BOARD MAIN SECTION · See page 11 for Circuit Boards Location.
1 A
2
3
4
5
6
7
8
9
10
11
12
Ref. No. D490 D491 D494 D495 D496 D497 D501 D502 D503 D504 D505 D506 D545 D546 D547 D548 D549 D551 D552 D553 D554 D555 D598 D598 D599 D601 D602 D603 D604 D605 D606 D607
13
Location Ref. No. H-7 H-7 H-8 H-8 H-8 H-8 B-10 B-10 B-10 B-10 C-4 C-4 C-6 C-6 C-4 B-4 C-4 B-6 B-5 B-5 B-5 C-4 B-8 B-9 B-4 B-8 B-8 B-8 B-7 C-5 D-5 D-5 D608 D649 D681 D698 D802 D803 D804 D805 D806 D807 D808 D809 IC301 IC302 IC303 IC304 IC401 IC402 IC404 IC414 IC415 IC416 IC501 IC601 Q501 Q503 Q504 Q505 Q506 Q507
14
Location Ref. No. D-8 C-7 E-8 B-6 H-10 H-10 H-10 H-10 H-11 H-11 H-11 H-11 G-4 H-3 E-4 E-3 G-8 H-8 H-7 F-10 F-10 F-10 C-10 D-10 E-9 E-9 B-10 B-10 B-10 B-9 Q508 Q509 Q510 Q511 Q546 Q547 Q548 Q549 Q554 Q555 Q556 Q557 Q558 Q559 Q560 Q561 Q596 Q598 Q599 Q601 Q604 Q605 Q606 Q607 Q608 Q609 Q610 Q611 Q613 Q645 Q681 Q698 Q745 Location B-9 C-4 C-5 C-4 C-6 C-4 C-3 C-4 B-5 B-5 C-6 B-5 C-4 B-4 C-4 C-4 C-6 B-9 B-4 D-8 B-7 B-8 B-8 B-7 B-7 D-5 D-5 D-5 E-8 C-7 E-8 B-6 F-7
· Semiconductor Location
B
C
D
E
(Page 31)
F
(Page 32)
G
(Page 35)
H
I
(Page 21) (Page 31) (Page 32) (Page 31) 36 21
Y
VOLUME BOARD 40
-- 43 --
-- 44 --
STR-DE635
4-20.
SCHEMATIC DIAGRAM MAIN SECTION(1/2) · See page 61 for IC Block Diagrams.
-- 45 --
-- 46 --
STR-DE635
4-21.
SCHEMATIC DIAGRAM MAIN SECTION (2/2)
· See page 43 for Printed Wiring Board. · See page 61 for IC Block Diagrams.
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
--47 --
-- 48 --
4-22.
IC1401
Pin No. 1 25 6, 7 8 9 10 11 12 13 14 15 16 20 21 22 23 25 26 27 30 31 32 40 41 42 43 49 50 51 52 53 60 61 62 69 70 71 72 73 74 75 76 80 81 82 83 89 90
IC PIN FUNCTION DESCRIPTION
CXD2712R AUDIO DSP(DIGITAL BOARD)
Pin Name VSS3 SOA SOD ECJ0, ECJ1 -- XHDWR XHDRD VSS4 VDD2 HRDY XHDCS HA0 HD0 HD4 VSS5 VDD3 HD5 HD7 XRST FGP0 FGP3 VSS6 ED0 ED8 VSS7 VDD4 ED9 ED15 TSTD VSS8 VDD5 ED16 ED23 VSS9 ED24 ED31 XOE VSS10 VDD6 CAS XWE RAS EA0 EA4 VSS11 VDD7 EA5 EA11 EA12 I/O -- O I NC I I -- -- O I I I/O -- -- I/O I O -- I/O -- -- I/O I -- -- I/O -- I/O O -- -- O O O I/O -- -- I/O O Ground Serial data output Conditional jump input terminal (7pin Connected to ground) No connection HCIF data write HCIF data read Ground +3.3V HCIF ready signal Open drain HCIF chip select HCIF address input HCIF data input/output Ground +3.3V HCIF data input/output Reset input "L": active Test data output Ground External RAM data input/output Ground +3.3V External RAM data input/output Test data input "L" = normal "H" = test (Connected to ground) Ground +3.3V External RAM data input/output Ground External RAM data input/output External RAM output enable Ground +3.3V External RAM column address strobe (Not used) External RAM write enable (Not used) External RAM raw address strobe External RAM address output/test data input Ground +3.3V External RAM address output/test data input External RAM address output Description
-- 49 --
Pin No. 91 92 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 120
Pin Name VSS0 EA13 EA15 EA16 TSTA PLDIVF PLDIVB CLKI CLKO VSS1 VDD0 AVSS AVDD PLLCK XPLLEN TST LRCT LROUT BKOUT VSS2 VDD1 BCK0 BCK1 LRCK0 LRCK1 SIA SID
I/O -- O O I I O I O -- -- -- -- I/O I I I O O -- -- I I I I I Ground External RAM address output Not used
Description
Test data input "L" = normal "H" = test (Connecting to ground) PLL input frequency select "L" = 256Fs "H" = 128Fs (Connecting to ground) PLL output frequency select "L" = 768Fs "H" = 1024Fs (Connecting to ground) Master clock input Master clock output (Not used) Ground +3.3V Ground for PLL cell VDD for PLL cell PLL output/test clock input PLL cell oscillation enable "L" oscillation enable "H" oscillation stop (Connecting to ground) Test data input "L" = normal "H" = test (Connecting to ground) Frequency counter input (Connecting to ground) LRCK0 divider output BCK0 divider output Ground +3.3V BCK input BCK input LRCK input LRCK input Serial data input
-- 50 --
IC1201
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
MB90573PFV-G-190-BND SYSTEM CONTROL(DIGITAL BOARD)
Pin Name SCLK SI SO CS IC D.SIG 5.1CH VCC SIN0 SOT0 N.C N.C XHDWR XHDRD SOD XHDCS HD7 HD6 HD5 HD4 HD3 HD2 HD1 HD0 HA0 XRST HRDY CS CCLK CDTI CDTO PD VSS C 96KHz N.C N.C DVCC DVSS N.C N.C AVCC AVR+ AVRAVSS EVSTB EVDATA EVCLK DISPMR DISPDATA I/O O I O O O I O -- I O O O O O I O O O O O O O O O O O I O O O I O -- -- O I I -- -- O -- -- -- -- -- O O O I I To CXD9511Q clock To CXD9511Q data input To CXD9511Q data output To CXD9511Q chip select To CXD9511Q reset(Pull Down near CXD9511Q) ZERO data detect 5.1CH muting. Power supply +5 V UART input. Used for rewriting flash memory UART output. Used for rewriting flash memory Not used (Connected to ground) Not used (Connected to ground) To CXD2712 data write To CXD2712 data read To CXD2712 LFE detection To CXD2712 chip select To CXD2712 HCIF data I/O To CXD2712 HCIF data I/O To CXD2712 HCIF data I/O To CXD2712 HCIF data I/O To CXD2712 HCIF data I/O To CXD2712 HCIF data I/O To CXD2712 HCIF data I/O To CXD2712 HCIF data I/O To CXD2712 address To CXD2712 reset To CXD2712 ready To AK4526A chip select To AK4526A clock To AK4526A data input To AK4526A data output To AK4526A reset Ground (Connected to ground) External power regulator capacitor 0.1u is connected to this terminal. To AK4526A Dfs Not used (Connected to ground) Not used (Connected to ground) Digital power supply +5 V Digital ground (Connected to ground) Not used (Connected to ground) Not used (Connected to ground) Analog power supply +5 V Power supply +5 V Ground (Connected to ground) Ground (Connected to ground) To TC9299 strobe To TC9299 data To TC9299 clock Display master request (Connected to MCU U.MREQ) Display data (Connected to MCU U.DATA) Description
-- 51 --
Pin No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name SLVDTA/REQ DISPCLK N.C VCC S.LAT S.DATA S.CLK DATA IN AUSTOP STEREO N.C N.C VSS N.C TH PROTEC STOP N.C N.C N.C N.C VIDEO(SW4) X1A X0A VIDEO(SW3) VIDEO(SW2) VIDEO(SW1) DIGITAL 1/4 TAPE NO/ YES VIDEO3 NO/ YES DTS NO/ YES ACMUTE 96K NO/YES T.MUTE S.MUTE HSTX MD2 MD1 MD0 REST VSS XO XI VCC PO0 PO1 RY-4/B RY-PRE RY-FRONT/A RY-FRONT/B
I/O O I I -- O O O I I I I I -- I I I I I I I I O -- -- O O O I I I I O I O O -- -- -- -- I -- -- -- -- I I O O O O
Description Slave data/request (Connected to MCU U.SREQ) Display clock (Connected to MCU U.CLOCK) Not used (Connected to ground) Power supply +5 V To tuner latch To tuner data To tuner clock PLL data in Auto stop input Stereo input Not used (Connected to ground) Not used (Connected to ground) Ground (Connected to ground) Not used (Connected to ground) TH Protector input Protector input AC power check Not used (Connected to ground) Not used (Connected to ground) Not used (Connected to ground) Not used (Connected to ground) Video select SW4 Not used Not used Video select SW3 Video select SW2 Video select SW1 Digital function Tape NO/YES input I VIDEO3 NO/ YES input DTS NO/ YES input Power amp mute ON/OFF output 96K NO/YES input Tuner muting Surround muting (Connected to ground) Hardware standby (Connected to power supply +5 V) MD2 (To MCU MD2) MD1 (Connect to power supply) MD0 (To MCU MD0) Reset (Connected to MB90553 U.RESET) Ground (Connected to ground) External ceramic filter 16MHz is connected to this terminal External ceramic filter 16MHz is connected to this terminal Power supply +5V Flash memory rewrite (Connected to ground) Flash memory rewrite (Connected to ground) 4/8 relay Pre relay Front speaker A relay Front speaker B relay
-- 52 --
Pin No. 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120
Pin Name RY-CENTER RY-REAR RY-WOOFER RY-HP RY-POWER ANG/DIG DIG-INB DIG-INA XMODE CL CE DI DO ERROR BYSYNC AUTO CSFLAG XSTATE VSS N.C
I/O O O O O O O O O O O O O I I I I I I -- -- Center speaker relay Rear speaker relay Sub Woofer relay Head phone relay Power relay Analog/digital selection Digital input select B Digital input select A Direct pass relay To LC89055 clock To LC89055 latch To LC89055 data To LC89055 C-bit Error output to LC89055 Non PCM sync detect flag LC89055 Non PCM data detect flag LC89056 C-bit change flag LC89055 Xtal status Frag LC89055 Ground (Connected to ground) Not used (Connected to ground)
Description
-- 53 --
IC1503
Pin No.
AK4526A A/D,D/A CONVERTER (DIGITAL BOARD)
Pin Name I/O SDTO source select pin Description
1
SDOS
I
"L": internal ADC output, "H": DAUX input ORed with serial control register if P/S = "L" (Connected to ground)
2
MCLK
I
MCKO clock frequency select pin "L": MCLK, "H": MCLK/2. ORed with serial control register if P/S = "L" (Connected to ground)
3 4 5 6 7 8 9 10
S/M BCLK LRCK SDT11 SDT12 SDT13 SDTO DAUX
I I/O I/O I I I O I
Audio data master/slave mode select pin "L": slave mode, "H": master mode (Connected to ground) Audio serial data clock pin Input/output channel clock pin DAC1 audio serial data input pin DAC2 audio serial data input pin DAC3 audio serial data input pin Audio serial data output pin AUX audio serial data input pin (Connected to ground) Double speed sampling mode pin
11
DFS
I
"L": normal speed, "H": double speed ORed with serial control register if P/S = "L" (Connected to ground)
12 13 14 15 16
DEM1 DEM0 MCKO D. 5V D. GND
I O -- --
De-emphasis pin ORed with serial control register if P/S = "L" (Connected to ground) Master clock output pin (Not used) Digital power supply pin Digital ground pin Power-down & reset pin
17
PD
I
When "L", the AK4526 is powered-down and the control registers are reset to default state. If the state of P/S, M/S, CAD0-1 changes, then the AK4526 must be reset by PD. X'tal oscillator select/test mode pin
18
TEST
I
"H": X'tal oscillator selected "L": External clock source selected "NC": If pin is floating then test mode is enabled. (Connected to ground)
19 20 21
ICKS1 ICKS0 CAD1
I I I
Input clock select 1 pin (Connected to ground) Input clock select 0 pin (Connected to ground) Chip address pin Used during the serial control mode. (Connected to ground)
22 23 24 25 26 27 28 29 30
CAD0 LOUT3 ROUT3 LOUT2 ROUT2 LOUT1 ROUT1 LIN LIN+
I O O O O O O I I
Chip address pin Used during the serial control mode. (Connected to ground) Lch #3 analog output pin Rch #3 analog output pin Lch #2 analog output pin Rch #2 analog output pin Lch #1 analog output pin Rch #1 analog output pin Lch analog negative input pin Lch analog positive input pin
-- 54 --
Pin No. 31 32 33 34 35 36 37 38 39 40 41 42 43 44
Pin Name RIN RIN+ VREFL VCOM VREFH A. 5V A. GND XTI MCLKI S/P CS CCLK CDTI CDTO
I/O I I I O I -- -- I I I I I I O Rch analog negative input pin Rch analog positive input pin
Description
Negative voltage reference input pin, AVSS (Connected to gorund) Common voltage output pin, AVDD/2 Large external capacitor is used to reduce power-supply noise Positive voltage reference input pin, AVDD Analog power supply pin Analog ground pin X'tal input pin (Not used) External master clock input pin if XTS = "L" Parallel/serial select pin "L": serial control mode, "H": parallel control mode (Connected to ground) Chip select pin in serial mode Control data clock pin in serial mode Control data input in serial mode Control data output pin in serial mode
If pins TEST, ICKS0, ICKS1, PD, S/P, DFS, DEM0, DEM1, CAD0, CAD1, S/M, MCLK, SDOS are not driven, then TEST, ICKS0, ICKS1, CAD0, CAD1, must be tied to either AVSS or AVDD. PD, S/P, DFS, DEM0, DEM1, S/M, MCLK, SDOS must be tied to either DVSS or DVDD.
-- 55 --
IC102
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
MB90553APF-G-138-BND DISPLAY CONTROL(DISPLAY BOARD)
Pin Name DCS EQ B.B MUTE D.D VOLUME POWER RY 5V CHECK -- -- VSS -- -- -- -- -- -- -- SOT0 SIN0 FL CLK FL DATA VCC FL LAT FL CLEAR SIRCS IN C -- -- -- -- -- -- AVCC AVRH AVRL AVSS AD KEY IN 1 AD KEY IN 2 AD KEY IN 3 AD KEY IN 4 VSS AD KEY IN 5 AD KEY IN 6 AD KEY IN 7 RDS SIGNAL STOP -- MD 0 MD 1 I/O O O O O O O O O -- -- -- -- -- -- -- -- -- -- O I O O -- O O I -- -- -- -- -- -- -- -- -- -- -- I I I I -- I I I I I -- I I DCS logo display data output to LED. EQ ON/OFF display data output to LED. BASS BOOST display data output to LED. MUTING display data output to LED. DOLBY DIGITAL display data output to LED. VOLUME display data output to LED. Power reay display. Power check (+5V) Not used. (Connected to ground) Not used. (Connected to ground) Ground (Connected to ground) Not used. (Connected to ground) Not used. (Connected to ground) Not used. (Connected to ground) Not used. (Connected to ground) Not used. (Connected to ground) Not used. (Connected to ground) Not used. (Connected to ground) UART data output to rewrite flash memory UART data intput to rewrite flash memory Clock output to flourescent display tube Data output to flourescent display tube Power supply +5 V Fluorescent latch Fluorescent clear SIRCS input External power regulator capacitor 0.1µ is connected to this terminal. Not used (Connected to ground) Not used (Connected to ground) Not used (Connected to ground) Not used (Connected to ground) Not used (Connected to gorund) Not used (Connected to ground) Analog power supply +5 V AVRH (Connected to power supply +5 V) SVRL (Connected to ground) Ground (Connected to ground) Key input 1 Key input 2 Key input 3 Key input 4 Ground (Connected to ground) Key input 5 Key input 6 Key input 7 RDS signal input. Stop input Not used (Connected to ground) MD 0 (To MD0 of MB90573) MD 1 (Connected to power supply +5 V) Description
-- 56 --
Pin No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
Pin Name MD 2 HSTX RDS CLOCK RDS DATA VOL UP VOL DOWN -- U-RESET U-SREQ U-MREQ U-DATA U-CLOCK AUBUS-IN SP-A SP-B POWER-KEY IN AUBUS-OUT VIRSION IN1 VIRSION IN 2 VIRSION IN 3 VIRSION IN 4 VIRSION IN 5 VIRSION OUT 1 VIRSION OUT 2 JOG-UP JOG-DOWN RESET -- -- -- VSS X0 X1 VCC -- -- LED CLK LED DATA LED CE LED CLR -- -- MBUS-V1 MBUS-DVD MBUS-TV
MBUS-STATUS
I/O I I I I O O -- O I O O O I I I I O I I I I I O O I I I -- -- -- -- -- -- -- -- -- I I I I -- -- I I I I -- O -- -- MD 2 (To MD2 of MB90573) Hardware STANDBY input RDS clock input RDS data input Volume up data output Volume down data output Not used (Connected to ground) Reset output (Connected to MB90573 RESET)
Description
Slave request and data input (Connected to MB90573 SLV DATA/REQ) Master request output (Connected to MB90573 DISPMR) Master data output (Connected to MB90573 DISP DATA) Master clock output (Connected to MB90573 DISPCLK) Audio bus input Speaker A signal input. Speaker B signal input. POWER-KEY input. Audio bus output Virsion input. Virsion input. Virsion input. Virsion input. Virsion input. Virsion output. Virsion output. Function encoder up input. Function encoder down input. Reset (Display MCU) Not used (Connected to ground) Not used (Connected to ground) Not used (Connected to ground) Ground (Connected to ground) External ceramic filter 4 MHz is connected to this terminal External ceramic filter 4 MHz is connected to this terminal Power supply +5 V Not used. (Connected to ground) Not used. (Connected to ground) LED clock input. LED data input. LED chip eneble input. LED clear input. Not used. (Connected to ground) Not used. (Connected to ground) V1 input from MBUS DVD input from MBUS TV input from MBUS STATUS input from MBUS Not used. (Connected to ground) Learning microprocessor latch output Not used. (Connected to ground) Not used. (Connected to ground)
-- LAT -- --
-- 57 --
IC1101
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
LC89055W DIGITAL AUDIO I/F RECEIVER (DIGITAL BOARD)
Pin Name DISEL DOUT DIN0 DIN1 DIN2 D. GND D. VDD R V IN LPF A. VDD A. GND CK OUT BCK LRCK DATA O XSTATE D. GND D. VDD XMCK XOUT XIN EMPHA AUDIO CSFLAG F0/P0/C0 F1/P1/C1 F2/P2/C2 F3/P3/C3 D. VDD D. GND AUTO BPSYNC ERROR DO DI CE CLK XSEL MODE0 MODE1 D. GND D. VDD DOSEL0 DOSEL1 CKSEL0 CKSEL1 XMODE I/O I O I O I -- O I I O -- -- -- O O O O -- -- -- O I O -- O -- -- -- -- -- -- O O O O I I I I I I -- -- O O I I I Input data select. (connected to ground.) EIAJ data and parity flag output terminal (Not used) Amplifier integrate data input terminal Amplifier integrate data input terminal (Connecting to ground) Amplifier integrate data input terminal (Connecting to ground) Digital ground Digital power supply Input terminal for VCO generator band adjustment Input terminal for VCO self running frequency set External LPF for PLL is connected to this terminal Analog power supply Analog ground 256fs or 128fs clock output terminal (Select CLKMD terminal) Bit clock output terminal L, R clock output terminal (L-ch: "H", R-ch: "L") Audio data output terminal Xtal status frag output. Digital ground Digital power supply Not used. Crystal oscillator output terminal (Not used.) Crystal oscillator input terminal Emphasis monitor output terminal ("H" = ON) (Not used.) Not used. C-bit change frag output. Not used. Not used. Not used. Not used. Digital power supply Digital ground Non PCM data detect flag output. Non PCM sync detect flag output. Error mute output terminal Microprocessor I/F. When CCB/SUB is "H", data output terminal (high level open drain output) (Not used) Microprocessor I/F. Data input terminal Microprocessor I/F. Chip enable/latch input terminal Microprocessor I/F. Clock input terminal Xtal select. (Connected to +5V.) Mode 0 input. (Connected to ground.) Mode 1 input. (Connected to ground.) Digital ground Digital power supply Output data select 0. (Connected to ground.) Output data select 1. (Connected to ground.) System clock select input 0. (Connected to ground.) System clock select input 1. (Connected to ground.) Reset input. Description
-- 58 --
4-23.
IC BLOCK DIAGRAMS
IC105 BA6208F (DISPLAY SECTION)
IC103 MSC1164GS-K (DISPLAY SECTION)
NC 1 NC 2 Q 32 NC 31 CHG 30 DIN
D
20 BIT SHIFT REGISTER
DOUT 3
CK
29 CLK
B IN 5 NC 6 GND 7 A IN 8
SWITCH SWITCH
MOTOR DRIVE MOTOR DRIVE REG
4 3 2 1
A OUT GND B OUT VCC
LS 4
CK
GATE CIRCUIT
20 BIT LATCH
CL 5 VCC 6 HVO20 HVO19 HVO18 HVO17 HVO16 HVO15 HVO14 HVO13 HVO12 HVO11 7 8 9 10 11 12 13 14 15 16
28 GND
OUTPUT CIRCUIT
27 Vhv 26 HVO1 25 HVO2 24 HVO3 23 HVO4 22 HVO5 21 HVO6 20 HVO7 19 HVO8 18 HVO9 17 HVO10
IC103 TD62C950RF (DISPLAY SECTION)
D OUT1 1 Q ST H VCC 21 P GND 22 L GND 23 CL 24 NC 25 STB 26 NC 27 NC 28 S IN 29 VDD 30 D Q
CK Q CK D
ST D Q 60 OUT40 41 OUT21 40 39 38 37 H VCC P GND L GND NC
OUT20 20
36 CHG 35 NC 34 CK 33 NC 32 S OUT 31 VDD
-- 59 --
IC1206 NJM2103 (DIGITAL SECTION)
CR
1
8
RESET
+ VSC 2 + VREF 7 VSA
OUTC
3
6
VSB/SESIN
GND
4 Q R S + +
5
V+
IC1503 AK4526 (DIGITAL SECTION)
MCKO ICKS1 DEM0 DVDD ICKS0 DEM1 DVSS CAD1 PD CAD0 XTS
44
43
42
41
40
39
38
37
36
35
34
SDOS 1 OCKS 2
XTO XTI Clock Gen MCLK HPF ADC
33 VREFL 32 RIN+
M/S 3 BICK 4 LRCK 5 SDTI1 6 SDTI2 7 SDTI3 8 SDTO 9 DAUX 10 DFS 11 DEM OCKS 1/2
MCLK BICK HPF LRCK SDTI1 SDTI2 SDTI3 DAC DAC DAC DAC SDOUT Audio I/F 16
DVSS
31 RIN30 LIN+ ADC 29 LINLPF LPF LPF LPF LPF LPF VR VR VR VR VR VR 28 ROUT1 27 LOUT1 26 ROUT2 25 LOUT2 24 ROUT3 23 LOUT3
DAC DAC
12
DEM1
13
DEM0
14
MCKO
15
DVDD
17
PD
18
XTS
19
ICKS1
20
ICKS0
21
CAD1
22
CAD0
-- 60 --
IC414, 415, 416 TC9299P (MAIN SECTION)
VSS OUT IN NC A-GND 1 2 3 4 5 16 VDD 15 14 13 12 OUT IN NC A-GND
IC501, 601 µPC2581V (MAIN SECTION) IC701 µPC2581V (REAR AMP SECTION)
L-ch
L-CH DATA LATCH CIRCUIT
R-CH DATA LATCH CIRCUIT
R-ch
PROTECTOR
BIAS CIRCUIT
REG DRIVE
PRE DRIVE 5
NF1
+VOUT1 VOUT1 COMP1
IN2 NF2 COMP2
VOUT2 +VOUT2
CS1 GND CK
6 7 8
MUTE
LEVEL SHIFT CIRCUIT
SHIFT REGISTER (13bit) STROBE GENERATOR CIRCUIT
PRE DRIVE 7
GND
DRIVE
LEVEL SHIFT CIRCUIT
11 CS2 10 STB 9 DATA
1
2
3 4
6
IN1
8 9 10 11 12 13 14 15
VCC1 VCC2 VEE
IC1 BU1924F (TUNER SECTION)
RCLK VDD2 NC XO VSS2 T1 T2
9
16
15
14
13
XI
12 11 10
CLOCK PLL 57kHz RDS/ARI PLL 1187.5Hz
DIGITAL
TEST
COMPARATOR
DEFFERENTIAL DECODER
ANTI-ALIASING FILTER
1
2
3
4
ANALOG
5 6
BIPHASE DECODER
8th SWITCHED CAPACITOR FILTER
7
8
MUX
VSS1
VSS3
QUAL
VREF
VDD1
RDAT
CMP
-- 61 --
SECTION 5 EXPLODED VIEWS
NOTE: · -XX, -X mean standardized parts, so they may have some differences from the original one. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · · The mechanical parts with no reference number in the exploded views are not supplied. Hardware (# mark) list and accessories and packing materials are given in the last of this parts list. Abbreviation CND : Canadian model
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
·
5-1. FRONT PANEL SECTION
13 12
12
12
a
11 10
FL101 #1
14
11 11 15 11
a
18
#1
11 9 17 19 18 11 16
7 6
8
not supplied
#1
20
#1 supplied with RV101 not supplied
21
3
#1
4 2
#1
supplied with RV401
1
5
Ref. No. 1 2 3 4 4 5 5 6 7 8 9 * 10 11 12
Part No. X-4951-035-1 3-350-426-01 4-221-474-01 4-217-853-11 4-217-853-51 X-4951-212-1 X-4951-252-1 4-957-383-01 4-996-698-01 X-4951-572-1 4-996-683-21 1-673-347-11 4-951-620-01 4-210-291-01
Description KNOB (VOL) ASSY SPRING, RING KNOB (JOG) ESCUTCHEON (US,CND) ESCUTCHEON (AEP) BASE (635U) ASSY, PANEL (US,CND) BASE (635CED) ASSY, PANEL (AEP) KNOB (F14) EMBLEM, SONY ESCUTCHEON (WIN) ASSY BUTTON (POWER) SP-SW BOARD SCREW (2.6 × 8), +BVTP SCREW (CASE 3 TP2)
Remarks
Ref. No. * 13 13 * 14 * 14 * 15 * 16 * 17 * 18 19 * 19 * 20 * 21 21 FL101
Part No. 4-982-682-01 X-4947-722-1 A-4419-393-A A-4419-395-A 1-673-350-11 1-673-348-11 4-990-797-01 4-921-941-01 A-4419-404-A A-4419-405-A 1-673-346-11 A-4419-407-A A-4426-060-A 1-517-781-11
Description
Remarks
CASE (414532) (US,CND) CASE ASSY (AEP) DISPLAY BOARD, COMPLETE(US,CND) DISPLAY BOARD, COMPLETE(AEP) LED BOARD ROTARY BOARD HOLDER (FL) CUSHION (FL) SW BOARD, COMPLETE(US,CND) SW BOARD, COMPLETE(AEP) MUTING BOARD VOLUME BOARD, COMPLETE(US,CND) VOLUME BOARD, COMPLETE(AEP) INDICATOR TUBE, FLUORESCENT
-- 62 --
5-2. CHASSIS SECTION 57(AEP) 56 55 54
#1 #1 #2 T901
57(US,CND) #1 58
#1 #1 #1 #1
53
#1
52
#2
59
not supplied #1
#1
60 61
#1 not supplied #1
d
#1
C c
#1
b
68 67 66 68 65 63 64 62
not supplied #1
#1 not supplied not supplied not supplied not supplied
69
not supplied #1
not supplied
71
#1 #1 #1 #1 a
d
68
not supplied
51
#1
70
b ca
#1
72 73 #1 #1 #1
#1
#1 not supplied
#1 not supplied
not supplied
#1
71
72
#1
73
Ref. No. 65 66 67 68 69 * * * * 69 70 70 70 71 Part No. A-4426-045-A 1-773-048-11 1-773-112-11 3-905-609-11 A-4419-390-A A-4419-391-A A-4419-379-A A-4419-380-A A-4419-382-A 4-985-642-01 X-4947-207-1 X-4947-208-1 4-977-358-11 1-433-771-11 1-433-884-11 Description Remarks
Ref. No. * * * * * 51 52 53 54 55
Part No. 1-673-349-11 1-673-354-11 1-673-353-11 1-673-359-11 1-673-355-11 3-703-244-00 1-769-743-11 1-769-744-11 1-783-531-11 4-217-900-01 4-217-900-21 4-218-334-01 1-673-357-11 1-673-356-11 1-673-940-11
Description H.P BOARD DC BOARD AC BOARD 4/8 BOARD SP BOARD BUSHING (2104), CORD CORD, POWER (CND) CORD, POWER (AEP) CORD, POWER (US) PANEL, BACK (US) PANEL, BACK (AEP) PANEL, BACK (CND) S-VIDEO BOARD VIDEO BOARD JOINT(H) BOARD
Remarks
DIGITAL BOARD, COMPLETE (AEP) WIRE (FLAT TYPE) (17 CORE) WIRE (FLAT TYPE) (19 CORE) SCREW (TRANSISTOR) REAR-AMP BOARD, COMPLETE(US,CND) REAR-AMP BOARD, COMPLETE(AEP) MAIN BOARD, COMPLETE(US) MAIN BOARD, COMPLETE(CND) MAIN BOARD, COMPLETE(AEP) CUSHION FOOT ASSY (F50150S) (AEP) FOOT ASSY (F50150S) (US,CND) CUSHION (US,CND) TRANSFORMER, POWER (AEP) TRANSFORMER, POWER (US)
* 56 ! 57 ! 57 ! 57 * 58 * * * * * 58 58 59 60 61
72 72 73 ! T901 ! T901 ! T901 TU301 TU301
* 63 64 * 65
1-673-358-11 TUNER BOARD 1-773-001-11 WIRE (FLAT TYPE) (15 CORE) A-4419-439-A DIGITAL BOARD, COMPLETE (US,CND)
1-433-885-11 TRANSFORMER, POWER (CND) 1-693-407-11 TUNER (US,CND) 1-693-409-11 TUNER (AEP)
-- 63 --
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
4/8
AC
DC
·
SECTION 6 ELECTRICAL PARTS LIST
RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable COILS uH: µH Abbreviation CND : Canadian model
When indicating parts by reference number, please include the board name.
NOTE: · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · -XX, -X mean standardized parts, so they may have some difference from the original one. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · CAPACITORS: uF: µF Ref. No. * Part No. Description
·
SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD...
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
· ·
Remarks
Ref. No.
Part No.
Description < TRANSISTOR >
Remarks
1-673-359-11 4/8 BOARD ********* Q901 < CONNECTOR >
8-729-230-49 TRANSISTOR 2SC2712-YG-TE85L < RESISTOR >
* CNP805 1-564-216-00 PIN, CONNECTOR 5P R901 < DIODE > D804 D805 8-719-053-18 DIODE 1SR154-400TE-25 8-719-053-18 DIODE 1SR154-400TE-25 < SWITCH > RY901 S801 1-571-309-21 SWITCH (INPEDANCE SELECTOR) ************************************************************ * 1-673-353-11 AC BOARD ******** 1-533-217-41 FUSE HOLDER * < CAPACITOR > C901 C902 C905 1-163-037-11 CERAMIC CHIP 1-163-037-11 CERAMIC CHIP 1-126-767-11 ELECT < CONNECTOR > ! CNJ901 ! CNJ901 CNP809 CNV901 * CNV902 1-251-718-11 1-785-285-11 1-784-921-11 1-564-321-00 1-565-792-11 OUTLET (2 GANG), AC (AC OUTLET)(US,CND) OUTLET, AC (1P) (AC OUTLET)(AEP) PIN, CONNECTOR 4P PIN, CONNECTOR 2P PIN, CONNECTOR 2P < DIODE > D901 D902 D903 D904 D905 D907 8-719-053-18 8-719-053-18 8-719-053-18 8-719-053-18 8-719-801-78 DIODE 1SR154-400TE-25 DIODE 1SR154-400TE-25 DIODE 1SR154-400TE-25 DIODE 1SR154-400TE-25 DIODE 1SS184-TE85L C805 C806 C807 C808 C809 1-130-781-00 1-130-781-00 1-128-555-91 1-126-967-11 1-126-967-11 FILM FILM ELECT ELECT ELECT 0.22uF 0.22uF 470uF 47uF 47uF 10% 10% 20% 20% 20% 0.022uF 0.022uF 1000uF 10% 10% 20% 25V 25V 16V C801 C803 C803 C804 C804 1-673-354-11 DC BOARD ******** 1-533-217-41 FUSE HOLDER < CAPACITOR > 1-104-664-11 ELECT 1-125-897-11 ELECT 1-125-997-11 ELECT 1-125-897-11 ELECT 1-125-997-11 ELECT 47uF 10000uF 12000uF 10000uF 12000uF 20% 20% 20% 20% 20% 25V 71V (US,CND) 63V (AEP) 71V (US,CND) 63V (AEP) 100V 100V 63V 50V 50V 1-755-298-11 RELAY < TRANSFORMER > ! T902 1-433-685-11 TRANSFORMER, POWER (AEP) ! T902 1-433-686-11 TRANSFORMER, POWER (US,CND) ************************************************************ R902 R903 1-216-073-00 METAL CHIP 1-216-065-91 RES,CHIP < RELAY > 10K 4.7K 5% 5% 1-202-725-00 SOLID 3.3M 10% 1/2W (US,CND) 1/10W 1/10W
8-719-016-74 DIODE 1SS352-TPH3 < CONNECTOR > < FUSE > CNP801 CNP802 * CNP803 CNP804 1-785-102-21 1-785-102-11 1-564-104-00 1-779-978-11 PIN, CONNECTOR 4P PIN, CONNECTOR 4P PIN, CONNECTOR (B3P-VH) 3P PIN, CONNECTOR 3P < DIODE > < EARTH TERMINAL > D801 D806 D810 8-719-072-05 DIODE RBV-602LF-A 8-719-070-30 DIODE PTZ-TE25-5.6A 8-719-074-75 DIODE PTZ-TE25-30B
! F901 ! F901 ! F903
1-533-311-11 FUSE, GLASS CYLINDRICAL (DIA.5) 8A/125V (US,CND) 1-532-504-51 FUSE TIME LAG 4A/250V (AEP) 1-532-464-51 FUSE TIME LAG 2.5A/250V (AEP)
* EB901
1-537-738-21 TERMINAL, EARTH (US,CND)
-- 64 --
Ver 1.1 2002. 02
DC
Ref. No. Part No. Description < EARTH TERMINAL > * EB801 1-537-738-21 TERMINAL, EARTH < FUSE > ! F801 ! F802 ! F803 1-533-311-11 FUSE, GLASS CYLINDRICAL (DIA.5) 8A/125V 1-533-311-11 FUSE, GLASS CYLINDRICAL (DIA.5) 8A/125V 1-533-419-11 FUSE, GLASS CYLINDRICAL (DIA.5) 4A/125V (US,CND) < TRANSISTOR > Q801 8-729-048-78 TRANSISTOR 2SD1733-TL-QR < RESISTOR > ! R801 1-247-727-11 CARBON 10 5% 1/2W F R802 1-249-401-11 CARBON 47 5% 1/4W F R803 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R804 1-216-081-00 METAL CHIP 22K 5% 1/10W ************************************************************ * A-4419-439-A DIGITAL BOARD, COMPLETE (US,CND) *********************** A-4426-045-A DIGITAL BOARD, COMPLETE (AEP) *********************** < CAPACITOR > C1001 C1005 C1006 C1006 C1007 C1008 C1009 C1010 C1011 C1012 C1013 C1014 C1015 C1016 C1017 C1018 C1019 C1020 C1031 C1101 C1102 C1103 C1104 C1105 C1106 C1107 C1108 C1109 C1110 C1111 1-165-319-11 CERAMIC CHIP 1-165-319-11 CERAMIC CHIP 1-126-935-11 ELECT 1-128-834-11 ELECT 1-126-965-11 ELECT 1-165-319-11 1-163-251-11 1-163-217-11 1-163-251-11 1-163-251-11 1-163-251-11 1-163-251-11 1-163-251-11 1-163-251-11 1-163-021-91 1-163-275-11 1-163-275-11 1-163-243-11 1-163-275-11 1-165-319-11 1-104-664-11 1-165-319-11 1-163-021-91 1-104-664-11 1-165-319-11 1-163-021-91 1-165-319-11 1-165-319-11 1-163-275-11 1-165-319-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 470uF 470uF 22uF 0.1uF 100PF 1PF 100PF 100PF 100PF 100PF 100PF 100PF 0.01uF 0.001uF 0.001uF 47PF 0.001uF 0.1uF 47uF 0.1uF 0.01uF 47uF 0.1uF 0.01uF 0.1uF 0.1uF 0.001uF 0.1uF 50V 50V 6.3V (US,CND) 10V (AEP) 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 50V 50V 16V 50V 50V 50V 50V 50V 50V C1209 C1210 C1211 C1212 C1213 C1214 C1215 C1216 C1217 C1218 C1219 C1220 C1221 C1222 C1223 C1224 C1225 C1226 C1227 C1228 C1229 C1229 C1230 C1301 C1303 C1304 C1305 C1306 C1307 C1309 1-165-319-11 1-104-664-11 1-163-251-11 1-163-251-11 1-165-319-11 1-104-664-11 1-126-935-11 1-126-935-11 1-126-935-11 1-126-959-11 1-165-319-11 1-126-957-11 1-119-824-11 1-165-319-11 1-165-319-11 1-165-319-11 1-165-319-11 1-126-960-11 1-104-664-11 1-163-021-91 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT ELECT ELECT CERAMIC CHIP ELECT ELECT MELF CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP 0.1uF 47uF 100PF 100PF 0.1uF 47uF 470uF 470uF 470uF 0.47uF 0.1uF 0.22uF 10uF 0.1uF 0.1uF 0.1uF 0.1uF 1uF 47uF 0.01uF 470uF 470uF 0.1uF 0.1uF 0.1uF 0.1uF 47uF 470PF 0.1uF 470uF Remarks Ref. No. C1156 C1157 C1201 C1202 C1203 C1204 C1205 C1206 C1207 C1208 Part No. 1-163-021-91 1-165-319-11 1-119-824-11 1-165-319-11 1-165-319-11 1-165-319-11 1-165-319-11 1-163-037-11 1-104-664-11 1-165-319-11 Description CERAMIC CHIP CERAMIC CHIP ELECT MELF CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.01uF 0.1uF 10uF 0.1uF 0.1uF 0.1uF 0.1uF 0.022uF 47uF 0.1uF
DIGITAL
Remarks 10% 20% 50V 50V 50V 50V 50V 50V 50V 25V 16V 50V 50V 16V 50V 50V 50V 16V 16V 16V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 50V
10% 20%
20% 5% 5%
20% 20% 20% 20% 20%
20% 20%
20% 20% 20%
20% 20% 10%
1-126-935-11 ELECT 1-127-720-91 ELECT 1-165-319-11 CERAMIC CHIP 1-165-319-11 CERAMIC CHIP 1-165-319-11 CERAMIC CHIP 1-165-319-11 1-104-664-11 1-163-133-00 1-165-319-11 1-126-935-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT
5% 0.25PF 5% 5% 5% 5% 5% 5% 10% 5% 5% 5% 5%
20% 16V (US,CND)(SUFFIX-12) 20% 16V (AEP)(SUFFIX-12) 50V (SUFFIX-12) 50V 50V 50V 16V 50V 50V 6.3V (US,CND) 10V (AEP) 50V 50V 50V 50V 50V 50V 50V 50V 50V
20% 5% 20%
C1309 C1310 C1311 C1312 C1313 C1314 C1315 C1401 C1402 C1403
1-128-834-11 ELECT 1-165-319-11 1-165-319-11 1-165-319-11 1-165-319-11 1-165-319-11 1-163-021-91 1-165-319-11 1-165-319-11 1-163-275-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
470uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.01uF 0.1uF 0.1uF 0.001uF
20%
20% 10% 20%
10%
10%
5%
5%
-- 65 --
The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DIGITAL
Ref. No. C1404 C1405 C1406 C1407 C1408 C1409 C1410 C1411 C1412 C1413 C1414 C1416 C1417 C1501 C1502 C1503 C1504 C1505 C1508 C1509 C1510 C1511 C1512 C1513 C1514 C1515 C1516 C1517 C1518 C1519 C1520 C1522 C1523 C1524 C1525 C1526 C1527 C1529 C1531 C1533 C1535 C1537 C1539 C1540 C1541 C1542 C1543 C1544 C1545 C1546 C1547 C1548 C1549 C1550 C1551 C1552 C1553 C1554 C1561 C1562 Part No. 1-165-319-11 1-165-319-11 1-165-319-11 1-165-319-11 1-165-319-11 1-104-664-11 1-165-319-11 1-165-319-11 1-165-319-11 1-165-319-11 1-104-664-11 1-104-664-11 1-165-319-11 1-104-664-11 1-104-664-11 1-163-251-11 1-104-664-11 1-104-664-11 1-126-965-11 1-104-664-11 1-126-965-11 1-126-965-11 1-104-664-11 1-126-964-11 1-165-319-11 1-126-964-11 1-165-319-11 1-126-965-11 1-165-319-11 1-165-319-11 1-126-965-11 1-126-965-11 1-106-347-00 1-126-965-11 1-126-965-11 1-126-965-11 1-163-239-11 1-163-239-11 1-163-239-11 1-163-239-11 1-163-239-11 1-163-239-11 1-104-664-11 1-104-664-11 1-104-664-11 1-163-227-11 1-126-965-11 1-165-319-11 1-163-227-11 1-126-965-11 1-163-227-11 1-126-965-11 1-163-227-11 1-126-965-11 1-163-227-11 1-126-965-11 1-163-227-11 1-126-965-11 1-126-965-11 1-126-965-11 Description CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT MYLAR ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT ELECT 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 47uF 0.1uF 0.1uF 0.1uF 0.1uF 47uF 47uF 0.1uF 47uF 47uF 100PF 47uF 47uF 22uF 47uF 22uF 22uF 47uF 10uF 0.1uF 10uF 0.1uF 22uF 0.1uF 0.1uF 22uF 22uF 1500PF 22uF 22uF 22uF 33PF 33PF 33PF 33PF 33PF 33PF 47uF 47uF 47uF 10PF 22uF 0.1uF 10PF 22uF 10PF 22uF 10PF 22uF 10PF 22uF 10PF 22uF 22uF 22uF 20% Remarks 50V 50V 50V 50V 50V 16V 50V 50V 50V 50V 16V 16V 50V 16V 16V 50V 16V 16V 50V 16V 50V 50V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 200V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 16V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V Ref. No. C1563 C1564 C1570 C1571 C1572 C1573 C1574 C1575 C1576 C3118 C3119 Part No. 1-126-965-11 1-126-965-11 1-119-824-11 1-165-319-11 1-126-965-11 1-106-347-00 1-126-965-11 1-126-965-11 1-126-965-11 1-163-233-11 Description ELECT ELECT ELECT MELF CERAMIC CHIP ELECT MYLAR ELECT ELECT ELECT CERAMIC CHIP 22uF 22uF 10uF 0.1uF 22uF 1500PF 22uF 22uF 22uF 18PF 18PF 20% 20% 20% 20% 5% 20% 20% 20% 5% 5% Remarks 50V 50V 50V 50V 50V 200V 50V 50V 50V 50V 50V
20% 20% 20% 20% 5% 20% 20% 20% 20% 20% 20% 20% 20%
1-163-233-11 CERAMIC CHIP < CONNECTOR >
CNP1301 1-784-923-11 CNP1302 1-779-799-11 CNP1303 1-779-977-11 CNP1305 1-784-923-11 CNS1301 1-784-778-11
PIN, CONNECTOR 7P PIN, CONNECTOR 9P PIN, CONNECTOR 6P PIN, CONNECTOR 7P CONNECTOR, FFC 17P
CNS1302 1-784-776-11 CONNECTOR, FFC 15P CNS1303 1-784-780-11 CONNECTOR, FFC 19P CNS1304 1-784-776-11 CONNECTOR, FFC 15P < DIODE > D1001 D1002 D1101 D1102 D1201 D1202 D1203 D1204 D1205 D1206 D1207 D1208 D1209 D1210 D1211 D1501 D1504 D1505 8-719-016-74 8-719-016-74 8-719-016-74 8-719-016-74 8-719-016-74 8-719-016-74 8-719-801-78 8-719-801-78 8-719-801-78 8-719-016-74 8-719-016-74 8-719-053-18 8-719-801-78 8-719-016-74 8-719-053-18 DIODE 1SS352-TPH3 DIODE 1SS352-TPH3 DIODE 1SS352-TPH3 DIODE 1SS352-TPH3 DIODE 1SS352-TPH3 DIODE 1SS352-TPH3 DIODE 1SS184-TE85L DIODE 1SS184-TE85L DIODE 1SS184-TE85L DIODE 1SS352-TPH3 DIODE 1SS352-TPH3 DIODE 1SR154-400TE-25 DIODE 1SS184-TE85L DIODE 1SS352-TPH3 DIODE 1SR154-400TE-25
20% 20%
20% 20% 5% 20% 20% 20% 5% 5% 5% 5% 5% 5% 20% 20% 20% 0.5PF 20% 0.5PF 20% 0.5PF 20% 0.5PF 20% 0.5PF 20% 0.5PF 20% 20% 20%
8-719-820-05 DIODE 1SS181-TE85L 8-719-820-05 DIODE 1SS181-TE85L 8-719-820-05 DIODE 1SS181-TE85L < EARTH TERMINAL >
* EB1001 1-537-738-21 TERMINAL, EARTH * EB1002 1-537-738-21 TERMINAL, EARTH < FERRITE BEAD > FB1101 FB1102 FB1103 FB1301 FB1302 1-414-813-11 1-414-813-11 1-414-813-11 1-414-813-11 1-414-813-11 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH
FB1401 1-414-813-11 FERRITE 0UH FB1402 1-414-813-11 FERRITE 0UH FB1403 1-414-813-11 FERRITE 0UH
-- 66 --
Ver 1.1 2002. 02
DIGITAL
Ref. No. Part No. Description < IC > IC1001 IC1005 IC1006 IC1007 IC1101 IC1102 IC1201 IC1202 IC1203 IC1204 IC1205 IC1206 IC1207 IC1301 IC1401 IC1402 IC1403 IC1404 IC1501 IC1502 IC1503 IC1504 IC1505 IC150