Text preview for : Yamaha-RXV1200_2200 rec.pdf part of Yamaha RXV1200, RXV2200 receiver



Back to : Yamaha-RXV1200_2200 rec.p | Home

AV RECEIVER
RX-V1200/RX-V1200RDS/




RX-V1200/RX-V1200RDS/
HTR-5490/RX-V2200
HTR-5490/RX-V2200
SERVICE MANUAL




IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that any service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please
contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.


I CONTENTS
TO SERVICE PERSONNEL .......................................... 1 AMP ADJUSTMENT .................................................... 36
IMPEDANCE SELECTOR ............................................. 1 DISPLAY DATA ..................................................... 37~38
FRONT PANELS ........................................................ 2~3 IC DATA ................................................................. 39~45
REAR PANELS .......................................................... 3~7 BLOCK DIAGRAM ................................................. 46~49
REMOTE CONTROL TRANSMITTER .......................... 8 PRINTED CIRCUIT BOARD .................................. 50~89
SPECIFICATIONS .................................................... 9~10 PIN CONNECTION DIAGRAM .............................. 90~91
INTERNAL VIEW ......................................................... 11 SCHEMATIC DIAGRAM ........................................ 92~99
DISASSEMBLY PROCEDURES ........................... 12~14 PARTS LIST ....................................................... 100~126
SELF DIAGNOSIS FUNCTION (DIAG) ................. 15~36 REMOTE CONTROL TRANSMITTER .............. 127~130




100792
P.O.Box 1, Hamamatsu, Japan
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200




I TO SERVICE PERSONNEL
1. Critical Components Information AC LEAKAGE
RX-V1200/RX-V1200RDS/




Components having special characteristics are marked s WALL EQUIPMENT TESTER OR
HTR-5490/RX-V2200




and must be replaced with parts having specifications equal OUTLET UNDER TEST EQUIVALENT
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.
INSULATING
G Meter impedance should be equivalent to 1500 ohm shunted TABLE
by 0.15µF.
G Leakage current must not exceed 0.5mA.
G Be sure to test for leakage with the AC plug in both polarities.

"CAUTION"
"F201, F202: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 8A, 125V
FUSE."
CAUTION
F201, F202: REPLACE WITH SAME TYPE 8A, 125V FUSE.
ATTENTION
F201, F202: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 8A, 125V.


WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where
applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and
possibly other entities) to cause cancer and/or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-
SON WHATSOEVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.



(7/8")
21.5
· DIMENSIONS
I IMPEDANCE SELECTOR 394 (15-1/2")
(5/8") 431.5 (17")
16
150 (5-7/8")
171 (6-3/4")




IMPEDANCE SELECTOR

WARNING:
Do not change the IMPEDANCE SELECTOR 435 (17-1/8")
(13/16")
21




switch setting while the power to this unit is
on, otherwise this unit may be damaged.
Unit : mm (inch)
1
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200




I FRONT PANELS
RX-V1200 (U, C, A, R, T, K models)




RX-V1200/RX-V1200RDS/
HTR-5490/RX-V2200
RX-V1200RDS (B, G models)




HTR-5490 (U, C, A, T models)




2
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



RX-V2200 (U, C, A, R, T models)
RX-V1200/RX-V1200RDS/
HTR-5490/RX-V2200




I REAR PANELS
RX-V1200 (U model)




RX-V1200 (C model)




3
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



RX-V1200 (A model)




RX-V1200/RX-V1200RDS/
HTR-5490/RX-V2200
RX-V1200 (R, T, K models)




RX-V1200RDS (B model)




4
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



RX-V1200RDS (G model)
RX-V1200/RX-V1200RDS/
HTR-5490/RX-V2200




HTR-5490 (U model)




HTR-5490 (C model)




5
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



HTR-5490 (A model)




RX-V1200/RX-V1200RDS/
HTR-5490/RX-V2200
HTR-5490 (T model)




RX-V2200 (U model)




6
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



RX-V2200 (C model)
RX-V1200/RX-V1200RDS/
HTR-5490/RX-V2200




RX-V2200 (A model)




RX-V2200 (R, T models)




7
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200




I REMOTE CONTROL TRANSMITTER
RX-V1200/HTR-5490 RX-V1200RDS RX-V2200




RX-V1200/RX-V1200RDS/
HTR-5490/RX-V2200
(U, C, A, R, T, K models) (B, G models)




RAV230
V754580 US




8
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



Residual Noise (IHF-A netwok)
I SPECIFICATIONS MAIN L/R SP OUT ................................................. 150 µV or less
Channnel Separation
(Vol -30 dB, EFFECT OFF)
I Audio Section PHONO (Input shorted, 1 kHz/10 kHz) .... 60 dB or more/55 dB or more
RX-V1200/RX-V1200RDS/




Minimum RMS Output Power (Power Amp. Section) CD, etc. (Input 5.1 k-ohms shorted, 1 kHz/10 kHz) ... 60 dB or more/45 dB or more
HTR-5490/RX-V2200




RX-V1200/RX-V1200RDS/HTR-5490 Tone Control Characteristics
(20 Hz to 20 kHz, 0.04% THD, 8 ohms) Bass: Boost/Cut ................................................ ±10 dB (50 Hz)
MAIN L/R ..................................................................... 80W + 80W Turnover Frequency ............................................ 350 Hz
CENTER ................................................................................. 80W Treble: Boost/Cut .............................................. ±10 dB (20 kHz)
REAR L/R/C .................................................... 80W + 80W + 80W Turnover Frequency ........................................... 3.5 kHz
(1 kHz, 0.04% THD, 8 ohms) Filter Characteristics
MAIN L/R MAIN, Rear SP Small (H.P.F.) .......................... 90 Hz, 12 dB/oct.
[U, C models] ............................................................ 95W + 95W SUBWOOFER (L.P.F.) ...................................... 90 Hz, 18 dB/oct.
[A, B, G, R, T, K models] .......................................... 90W + 90W Bass Extension
CENTER 60 Hz ...................................................................................... 6 dB
[U, C models] ....................................................................... 95W
[A, B, G, R, T, K models] ..................................................... 90W I Video Section
REAR L/R/C
[U, C models] ................................................ 95W + 95W + 95W S-Video Signal Type
[A, B, G, R, T, K models] .............................. 90W + 90W + 90W [U, C models] ....................................................................... NTSC
RX-V2200 [R, T, K models] ....................................................... NTSC or PAL
(20 Hz to 20 kHz, 0.04% THD, 8 ohms) [A, B, G models] ...................................................................... PAL
MAIN L/R ................................................................. 100W + 100W Video Signal Level
CENTER ............................................................................... 100W ............................................................................ 1 Vp-p / 75 ohms
REAR L/R/C .............................................. 100W + 100W + 100W S-Video Signal Level
(1 kHz, 0.04% THD, 8 ohms) Y ......................................................................... 1 Vp-p / 75 ohms
MAIN L/R ................................................................. 115W + 115W C .................................................................. 0.286 Vp-p / 75 ohms
CENTER ............................................................................... 115W Component Signal Level
REAR L/R/C .............................................. 115W + 115W + 115W Y ......................................................................... 1 Vp-p / 75 ohms
Maximum Power (EIAJ) Cb/Cr ............................................................... 0.7 Vp-p / 75 ohms
RX-V1200/HTR-5490 [R, T, K models] Maximum Input Level
(1 kHz, 10% THD, 8 ohms) .......................................................................................... 1.5 Vp-p
MAIN L/R ................................................................. 125W + 125W Signal to Noise Ratio
CENTER ............................................................................... 125W ................................................................................. 50 dB or more
REAR L/R/C .............................................. 125W + 125W + 125W Monitor Out Frequency Response
RX-V2200 [R, T models] S-Video Signal Level ................................. 5 Hz to 10 MHz, -3 dB
(1 kHz, 10% THD, 8 ohms) Component Signal Level .............................. DC to 60 MHz, -3 dB
MAIN L/R ................................................................. 155W + 155W
CENTER ............................................................................... 155W I FM Section
REAR L/R/C .............................................. 155W + 155W + 155W
Dynamic Power Per Channel (IHF) Tuning Range
RX-V1200/RX-V1200RDS/HTR-5490 [U, C models] ................................................... 87.5 to 107.9 MHz
MAIN L/R (8/6/4/2 ohms) ............................... 105/130/170/200 W [A, B, G models] ........................................... 87.50 to 108.00 MHz
RX-V2200 [R, T, K models] .................. 87.5 to 108.0 / 87.50 to 108.00 MHz
MAIN L/R (8/6/4/2 ohms) ............................... 130/160/200/245 W 50 dB Quieting Sensitivity (IHF)
DIN Standard Output Power Per Channel (100% Mod)
RX-V1200RDS [G model] Mono .................................................................. 2.0 µV (17.3 dBf)
(1 kHz, 0.7% THD, 4 ohms) Stereo .................................................................. 25 µV (39.2 dBf)
MAIN L/R ................................................................. 135W + 135W Usable Sensitivity (IHF)
CENTER ............................................................................... 135W Mono .................................................................. 1.0 µV (11.2 dBf)
REAR L/R/C .............................................. 135W + 135W + 135W Selectivity
Dynamic Headroom at 400 kHz ............................................................................ 70 dB
RX-V1200/HTR-5490 Signal to Noise Ratio (IHF)
(8 ohms) Mono / Stereo .......................................................... 76 dB / 70 dB
[U model] ........................................................................... 1.2 dB Harmonic Distortion
[C model] ........................................................................... 1.1 dB (1 kHz)
RX-V2200 Mono/Stereo ................................................................. 0.2 / 0.3 %
(8 ohms) Stereo Separation
[U, C models] .................................................................... 1.1 dB 1 kHz .................................................................................... 45 dB
IEC Power Frequency Response
RX-V1200RDS [G model] 20 Hz to 15 kHz .......................................................... +0.5 / -2 dB
MAIN L/R (1 kHz, 0.04% THD, 8 ohms) ..................... 90W + 90W Antenna Input
Damping Factor ...................................................................... 75 ohms unbalanced
MAIN L/R (20 Hz to 20 kHz, SPEAKER-A, 8 ohms) ... 80 or more
Input Sensitivity / Input Impedance I AM Section
PHONO (MM) ................................................. 2.5 mV / 47 k-ohms
CD, etc. ......................................................... 150 mV / 47 k-ohms Tuning Range
EXT. DECODER [U, C models] ..................................................... 530 to 1,710 kHz
MAIN L/R ................................................... 150 mV / 47 k-ohms [A, B, G models] ................................................. 531 to 1,611 kHz
CENTER, SURROUND L/R, SUBWOOFER ... 150 mV / 40 k-ohms [R, T, K models] ......................... 530 to 1,710 / 531 to 1,611 kHz
Maximum Input Signal Level Usable Sensitivity
PHONO (MM) (1 kHz, 0.1% THD) .................................... 100 mV ........................................................................................ 300 µV/m
CD, etc. (1 kHz, 0.5% THD, EFFECT ON) ........................... 2.2 V Antenna
Output Level / Output Impedance ................................................................................. Loop Antenna
REC OUT ..................................................... 150 mV / 0.9 k-ohms
PRE OUT ....................................................... 2.57 V / 1.2 k-ohms I General
SUB WOOFER [MAIN SP: Small] ................... 4.0 V/1.2 k-ohms
Headphone Jack Rated Output / Impedance Power Supply
1 kHz, 40 mV, 8 ohms ..................................... 0.15 V / 100 ohms [U, C models] ...................................................... AC 120 V, 60 Hz
Frequency Response [A model ] ............................................................ AC 240 V, 50 Hz
CD, etc. to MAIN (10 Hz to 100 kHz) ................................ 0/-3 dB [B, G models] ...................................................... AC 230 V, 50 Hz
Power Amp. section (5 Hz to 100 kHz) ............................. 0/-3 dB [R model] .................................. AC 110/120/220/240 V, 50/60 Hz
RIAA Equalization Deviation [T model ] ............................................................ AC 220 V, 50 Hz
PHONO (MM) (20 Hz to 20 kHz) .................................... 0±0.5 dB [K model ] .................................................... AC 110/220 V, 60 Hz
Total Harmonic Distortion Power Consumption
(20 Hz to 20 kHz) RX-V1200/RX-V1200RDS/HTR-5490
PHONO (MM) to REC OUT (1V) .................................. 0.02% or less [U model] ............................................................................. 260 W
CD, etc. (EFFECT OFF) to MAIN SP OUT (50W /8 ohms) .. 0.04% or less [C model] .............................................................. 270 W / 370 VA
Signal to Noise Ratio (IHF-A network) [A, B, G, R, T, K models] .................................................... 360 W
(Input shorted) RX-V2200
PHONO (MM) to REC OUT (5 mV) [U model] ............................................................................. 390 W
[U, C, R, T, K models] ........................................... 86 dB or more [C model] .............................................................. 400 W / 500 VA
[A, B, G models] .................................................... 81 dB or more [A, R, T models] .................................................................. 410 W
CD, etc. (EFFECT OFF) to MAIN SP OUT Standby Power Consumption (reference data)
250 mV ................................................................ 100 dB or more [U, C, A, B, G models] ......................................................... 1.2 W
9
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



[R, T models] AC 220V, 50Hz ............................................. 1.5 W Remote control transmitter, Manganese batteries, Indoor FM
[K model] AC 220V, 60Hz .................................................... 1.5 W antenna, AM loop antenna, Antenna adaptor [B model], Power
Maximum Power Consumption cord ass'y [V1200/V2200 U, C models]
RX-V1200/RX-V2200 [R model]
5ch Drive, 10% THD ........................................................... 585 W




RX-V1200/RX-V1200RDS/
AC Outlets * Specifications are subject to change without notice due to product




HTR-5490/RX-V2200
2 switched outlets improvements.
[U, C models] ..................................................... 80W max., total
[G model] RX-V1200RDS only ....................... 100W max., total U .......... U.S.A. model C ...... Canadian model
[R, T models] ...................................................... 50W max., total A .......... Australian model B ...... British model
1 switched outlet G .......... European model R ...... General model
[A, B models] B: RX-V1200RDS only ...................... 100W max.
Dimensions (W x H x D) T .......... Chinese model K ...... Korean model
............................. 435 x 171 x 431.5 mm (17-1/8" x 6-3/4" x 17")
Weight
.................................................................... 15.0 kg (33 lbs. 1 oz.)
Finish
RX-V1200 ................................... Gold color (R, T, K) models
Black color (U, C, R, A) moleds Manufactured under license from Dolby Laboratories.
RX-V1200RDS ........................... Gold color (G) model "Dolby", "Pro Logic" and the double-D symbol are trademarks of
Black color (B, G) models Dolby Laboratories.
Titan color (B, G) moldels
HTR-5490 ................................... Gold color (T) model
Black color (U, C, A) models
RX-V2200 ................................... Gold color (R, T) models
Black color (U, C, R, A) models
Accessories "DTS" and "DTS Digital Surround" are registered trademarks of
Digital Theater Systems, Inc.
· Set Menu Table
No. SET MENU PRESET VALUE SETTING RANGES
1. SPEAKER SET
1A CENTER SPEAKER LARGE LARGE, SMALL, NONE
1B MAIN SPEAKER LARGE LARGE, SMALL
1C REAR L/R SPEAKER LARGE LARGE, SMALL, NONE
1D REAR CENTER SPEAKER LARGE LARGE, SMALL, NONE
1E LFE/BASS OUT BOTH SUBWOOFER, MAIN, BOTH
1F MAIN LEVEL NORMAL NORMAL, ­10dB
2. LOW FREQ. TEST TEST TONE : OFF OFF, ON
OUTPUT : MAIN L/R MAIN L/R, L, C, R, RS, RC, LS, SWFR
FREQ. : 88Hz 35Hz/ ··· /88Hz/ ··· /WIDE
3. L/R BALANCE CENTER L, ··· , CENTER, ··· , R (40 steps)
4. HP TONE CONTROL HP BASS : 0dB ­6dB -- +3dB (1dB step)
HP TREBLE : 0dB ­6dB -- +3dB (1dB step)
5. CENTER GRAPHIC EQ. 100Hz : 0dB ­6dB -- +6dB (1dB step)
300Hz : 0dB ­6dB -- +6dB (1dB step)
1kHz : 0dB ­6dB -- +6dB (1dB step)
3kHz : 0dB ­6dB -- +6dB (1dB step)
10kHz : 0dB ­6dB -- +6dB (1dB step)
6. INPUT RENAME DVD (Currently selected input)
7. I/O ASSIGNING
7A COMPONENT VIDEO INPUT 1 [A] : DVD DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX
COMPONENT VIDEO INPUT 2 [B] : D-TV/LD DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX
7B OPTICAL OUT 1 (1) : MD/TAPE DVD, MD/TAPE, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX, PHONO, CD, CD-R
OPTICAL OUT 2 (2) : CD-R DVD, MD/TAPE, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX, PHONO, CD, CD-R
7C OPTICAL IN 1 (3) : CD CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, PHONO
OPTICAL IN 2 (4) : CD-R CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, PHONO
OPTICAL IN 3 (5) : DVD CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, PHONO
OPTICAL IN 4 (6) : D-TV/LD CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, PHONO
7D COAXIAL IN 1 (7) : CD CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX, PHONO
COAXIAL IN 2 (8) : CBL/SAT CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX, PHONO
8. INPUT MODE AUTO AUTO/LAST
9. PARAMETER INITIALIZE PARAMETER INITIALIZE The number key of the remote controller is pushed and initialized.
10. LFE LEVEL SPEAKER : 0dB ­2dB -- 0dB (1dB step)
HEADPHONE : 0dB ­2dB -- 0dB (1dB step)
11. DYNAMIC RANGE SP DYNAMIC RANGE : MAX MAX, STD, MIN
HP DYNAMIC RANGE : MAX MAX, STD, MIN
12. SPEAKER DELAY TIME CENTER : 0ms 0ms -- 5ms (1ms step)
REAR CENTER : 3ms 0ms -- 30ms (1ms step)
13. DISPLAY SET BLUE BACK : AUTO AUTO/OFF
OSD SHIFT : 0 ­5 -- +5 (1 step)
DIMMER : 0 ­4 -- 0 (1 step)
14. MEMORY GUARD OFF ON/OFF
15. DUAL MONO MAIN MAIN, SUB, ALL
10
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



· The variable range of the parameter (Min/Max/Step)
Parameter name Pro Logic Pro Logic II Pro Logic II Neo:6 2ch DD/dts/AAC 6.1/ES Unit
Movie Music
RX-V1200/RX-V1200RDS/




(P.) INIT. DLY - - - - 1/99/1 1/99/1 1/99/1 ms
HTR-5490/RX-V2200




(P.) ROOM SIZE - - - - 0.1/2.0/0.1 0.1/2.0/0.1 0.1/2.0/0.1 -
(P.) LIVENESS - - - - 0/10/1 0/10/1 0/10/1 -
S. DELAY 10/25/1 10/25/1 0/15/1 0/30/1 0/49/1 0/49/1 0/49/1 ms
S. INIT. DLY - - - - - 1/49/1 1/49/1 ms
S. ROOM. SIZE - - - - 0.1/2.0/0.1 0.1/2.0/0.1 0.1/2.0/0.1 -
S. LIVENESS - - - - 0/10/1 0/10/1 0/10/1 -
RC. INT.DLY - - - - - - 1/49/1 ms
RC. ROOM, SIZE - - - - - - 0.1/2.0/0.1 -
RC. LIVENESS - - - - - - 0/10/1 -
REV. TIME - - - - 1.0/5.0/0.1 1.0/5.0/0.1 1.0/5.0/0.1 s
REV. DELAY - - - - 0/250/1 0/250/1 0/250/1 ms
REV. LEVEL - - - - 0/100/1 0/100/1 0/100/1 %
Panorama - OFF OFF/ON - - - - -
Dimension - 0 (STD) -3/+3/1 - - - - -
C Width - 0 0/7/1 - - - - -

6ch Stereo Parameter Unit
CT. LEVEL 0/100/1 %
RL. LEVEL 0/100/1 %
RC. LEVEL 0/100/1 %
RR. LEVEL 0/100/1 %



I INTERNAL VIEW
1 POWER (1) P.C.B.
2 POWER (7) P.C.B.
3 MAIN (6) P.C.B. 1 2 3 4 5 6 78 9 0 A
4 MAIN (4) P.C.B.
5 MAIN (5) P.C.B.
6 POWER (10) P.C.B.
7 TUNER
B
8 VIDEO (4) P.C.B.
9 VIDEO (2) P.C.B. C
0 VIDEO (1) P.C.B. V
D
A VIDEO (6) P.C.B.
B VIDEO (8) P.C.B. U E
C VIDEO (7) P.C.B.
T
D VIDEO (5) P.C.B.
E DSP P.C.B. F
F FUNCTION P.C.B. S
G
G POWER (4) P.C.B.
R H
H MAIN (1) P.C.B.
I OPERATION (5) P.C.B. Q
J OPERATION (4) P.C.B.
K MAIN (2) P.C.B.
L OPERATION (2) P.C.B.
M POWER (8) P.C.B. N M K
N OPERATION (6) P.C.B.
(RX-V2200 only) P O L J I
O OPERATION (1) P.C.B.
P OPERATION (3) P.C.B.
Q POWER (3) P.C.B.
R OPERATION (7) P.C.B.
S POWER (5) P.C.B.
T POWER (2) P.C.B.
U MAIN (7) P.C.B.
V MAIN (3) P.C.B.
11
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



3
I DISASSEMBLY PROCEDURES
2 1
(Remove parts in the order as numbered.) Top Cover




RX-V1200/RX-V1200RDS/
HTR-5490/RX-V2200
Disconnect the power cord from the AC outlet.
3
1. Removal of Top Cover
a. Remove 2 screws (1), 4 screws (2) and 5 screws (3).
(Fig. 1)
b. Slide the Top Cover rearward to remove it. (Fig. 1)

2. Removal of Front Panel 5
a. Remove the BASS and TREBLE knobs (4). (Fig. 1)
b. Remove 9 screws (5) and then remove the Front 2
Panel forward. (Fig. 1)

3. Removal of Sub Chassis
a. Remove 4 push rivets (6) and then remove the Side
Plates. (Fig. 2) 5
b. Remove 2 screws (7) and 2 screws (8), and then Front Panel
remove the Sub Chassis forward. (Fig. 2) 4
Fig. 1
4. Removal of DSP P.C.B.
a. Remove 2 screws (9) and then remove the Supports.
(Fig. 2) C
b. Remove 4 screws (0) and then remove the Brackets.
(Fig. 2) Side 6
Plate L
c. Remove 1 screw (A). (Fig. 2) VIDEO (5) P.C.B.
6 7
d. Remove 9 screw (B). (Fig. 3) DSP P.C.B.
e. Remove the DSP P.C.B. upward. (Fig. 2) Support
9 0
5. Removal of VIDEO (5) P.C.B.
0
a. Remove 2 screws (C). (Fig. 2) 0
b. Remove the VIDEO (5) P.C.B. which is connected 8 A 0
directly to the lower P.C.B. with connectors. (Fig. 2) 6
Sub Chassis 8 Bracket
7
Side Plate
R 6

Fig. 2

B E




D
Fig. 3
12
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



6. Removal of VIDEO (1), VIDEO (2), VIDEO (4) and VIDEO (8)P.C.B. VIDEO (2)P.C.B.
VIDEO (8) P.C.B.s and Tuner VIDEO (1)P.C.B. VIDEO (4)P.C.B.
a. Remove 17 screws (D). (Fig. 3)
RX-V1200/RX-V1200RDS/




b. Remove VIDEO (1), VIDEO (2), VIDEO (4) and VIDEO VIDEO (5)P.C.B. Extension cable
HTR-5490/RX-V2200




(8) P.C.B.s and the Tuner. (Fig. 4) Rubber sheet
and cloth
When checking the P.C.B.:
· Put the rubber sheet and a cloth over the equipment.
Then place the P.C.B. upside down on the cloth and
Tuner
check it. (Fig. 4)
· Connect VIDEO (5) and FUNCTION P.C.B.s by
using the extension cable (AAX30610) for the P.C.B.
check. (Fig. 6)
· Reconnect all cables (connectors) that have been
disconnected.
· The P.C.B. removed from the rear panel does not
work because its grounding is loose. Be sure to Fig. 4
connect the ground of each P.C.B. to the chassis or
GND with a jumper wire or the like.



7. Removal of VIDEO (6), VIDEO (7), and FUNCTION
P.C.B.s
a. Remove CB212, CB975, CB510, CB509, CB505 and
CB503. (Fig. 5)
b. Remove 9 screws (E). (Fig. 3)
c. Remove VIDEO (6), VIDEO (7), and FUNCTION CB503
P.C.B.s. (Fig. 6)

When checking the P.C.B.:
CB212 CB510
· Put a cloth beside the equipment. Then place the
P.C.B. on the cloth and check it. (Fig. 4) CB509
· Connect VIDEO (5) and FUNCTION P.C.B.s by
CB505
using the extension cable (AAX30610) for the P.C.B. CB975
check. (Fig. 6)
· Reconnect all cables that have been disconnected.
· The P.C.B. removed from the rear panel does not
work because its grounding is open. Be sure to
Fig. 5
connect the ground of each P.C.B. to the chassis or
GND with a jumper wire or the like.
FUNCTION P.C.B.
Block
and
cloth




Extension cable
VIDEO (6) P.C.B. (AAX30610)

VIDEO (7) P.C.B.

Fig. 6
13
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



8. Removal of Duct/Fan Section (If applicable) Duct/Fan Frame
G
a. Remove 2 screws (F) and 2 screws (G). (Fig. 7)
b. Remove the duct/fan together with the frame by lifting




RX-V1200/RX-V1200RDS/
them up. G




HTR-5490/RX-V2200
F
Fig. 7




9. Removal of MAIN (1), MAIN (2), POWER (4) and MAIN (2) P.C.B. I
POWER (8) P.C.B.'s. POWER (4) P.C.B.
a. Remove 2 screws (H), 3 screws (I) and 1 screw (J).
(Fig. 8) POWER (8) I J
b. Remove MAIN (1), MAIN (2), POWER (4) and POWER P.C.B.
MAIN (1) P.C.B.
(8) P.C.B.s. (Fig. 8)



I




H


Fig. 8




14
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200




I SELF DIAGNOSIS FUNCTION (DIAG)
There are 18 DIAG menu items, each of which has sub-menu items. Listed in the table below are menu items and sub-menu
RX-V1200/RX-V1200RDS/




items. (Some diagnostic functions do not apply to all models or to all markets.)
HTR-5490/RX-V2200




No DIAG menu sub-menu
1 YSS938 1. ANALOG BYPASS
2. YSS 0dB
3. YSS FULL BIT
2 YSS-CS 1. YSS-CS 0dB
2. YSS-CS FULL BIT
3 CS-YSS 1. CS-YSS 0dB
2. CS-YSS FULL BIT
4 CS49329 1. CS49329 0dB
2. CS49329 FULL BIT
5 HP ROUTE 1. HP 0dB
2. HP FULL BIT
6 RAM THROUGH 1. RAM 0dB
2. MAIN ATT
7 DOLBY PRO 1. PRO LOGIC I
LOGIC 2. PRO LOGIC II
3. NEO: 6
8 SPEAKER SET 1. MAIN: SMALL 0dB
2. MAIN: LARGE -10dB
3. CENTER: NONE
4. LFE/BASS: MAIN
5. FRONT MIX: 5ch
6. REAR C: MUTE
7. REAR L/R: MUTE
9 EFFECT OFF/ 1. VFD CHECK (Initial display)
DISPLAY CHECK 2. VFD DISP OFF (All segments OFF)
3. VFD DISP ALL (All segments ON 100%)
4. VFD DIMMER (All segments ON 50%)
5. CHECKED PATTERN (ON in lattice)
10 MANUAL TEST 1. TEST ALL
2. TEST MAIN L
3. TEST CENTER
4. TEST MAIN R
5. TEST REAR R
6. TEST REAR CENTER
7. TEST REAR L
8. TEST LFE
11 RS-232C 1. TX DATA
2. HARD FLOW
12 FACTORY PRESET 1. PRESET INHIBIT (memory initialization inhibited)
2. PRESET RESERVED (memory initialized)
13 AD DATA CHECK 1. DC/PS (protection)
/FAN TEST 2. THM/FAN OUT
3. REC-OUT
4. IMP SW/POWER LIMIT
5. K0/K1 (panel key)
6. FAN DRIVE TEST: HIGH (Fan test only applies to models with a fan.)
7. FAN DRIVE TEST: MID (Fan test only applies to models with a fan.)
8. FAN DRIVE TEST: LOW (Fan test only applies to models with a fan.)




15
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200




No DIAG menu sub-menu
14 IF STATUS 1. IS 1
2. IS 2




RX-V1200/RX-V1200RDS/
3. IS 3




HTR-5490/RX-V2200
4. CS 1
5. CS 2
6. CS 3
7. CS 4
8. CS 5
9. BY1
10. BY2
11. BY3
12. BY4
13. BC1
14. BC2
15. BC3
16. BC4
17. BC5
18. YS1
19. YS2
20. YS3
21. CS
22. MTT
15 DSP RAM CHECK 1. YSS938 BUS CHECK
2. PLD/SRAM BUS CHECK
16 CS DL CODE 1. ROM DATA VERSION
2. TOC AREA 0
3. TOC AREA 1
4. TOC AREA 2
5. TOC AREA 3
6. TOC AREA 4
7. TOC AREA 5
8. SUM CHECK AREA 0
9. SUM CHECK AREA 1
10. SUM CHECK AREA 2
11. SUM CHECK AREA 3
12. SUM CHECK AREA 4
13. SUM CHECK AREA 5
17 SOFT SW 1. SW MODE
2. MODEL SETTING
3. TUNER DESTINATION
4. TUNER EXIST
5. RDS EXIST
6. ZONE 2 EXIST
7. VIDEO FORMAT
18 ROM VERSION/CHECK SUM/ 1. VERSION
PORT 2. SUM ALL/PROGRAM
3. SUM 232C/MAKER
4. PORT
5. AAC PORT




16
RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200



· Starting DIAG
Press the "STANDBY/ON key while pressing those two keys indicated in the figure on Keys of main unit
the right.
RX-V1200/RX-V1200RDS/




PRESET/
HTR-5490/RX-V2200




A/B/C/D/E TUNING




· Starting DIAG in the protection cancel mode
If the protection function works and causes hindrance to trouble diagnosis, cancel the
protection function as described below, and it will be possible to enter the DIAG mode. Turn on the power while
(The protection functions other than the excess current detect function will be pressing these keys.
cancelled.)

Press the "STANDBY/ON key while pressing those two keys indicated in the figure on
the right. At this time, keep pressing those two keys for 3 seconds or longer.

In this mode, the "SLEEP" segment of the FL display of the main unit flashes to indicate that the mode is DIAG mode with the
protection functions cancelled.

CAUTION!
Using this product with the protection function disabled may cause damage to itself. Use special care for this point when
usin