Text preview for : SAMSUNG SP47W3HFX J52A(P)_REV.4.pdf part of SAMSUNG SP47W3HFX Service Manual
Back to : SAMSUNG SP47W3HFX J52A(P) | Home
PROJECTION TV RECEIVER
Chassis : Model: J52A(P)_REV.4 SP47W3HFX/BOB SP47W3HFX/COM SP47W3HFX/EUE SP47W3HFX/XEH SP55W3HFX/XEC
PROJECTION TV RECEIVER
CONTENTS
1. Precautions 2. Reference Information 3. Specifications 4. Alignment and Adjustments 5. Troubleshooting 6. Exploded View and Parts List 7. Electric Parts List 8. Block Diagrams 9. Wiring Diagram 10. Schematic Diagrams
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
LEAKAGE CURRENT TESTER
(READING SHOULD NOT BE ABOVE 0.5mA)
EARTH GROUND
Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called "horizontal disable" or "hold-down".) Heed the high voltage limits. These include the Xray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
Samsung Electronics
1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer's warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs "integral implosion" protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such "permanently attached" yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning 1 : First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning 2 : An electrolytic capacitor installed with the wrong polarity might explode.
1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). "CAUTION : Double-pole/neutral fusing"
6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last. 9. When some parts inside the optical engine (except lamp) are damaged, replace the whole optical engine.
Samsung Electronics
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power-- this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as "anti-static"; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
1-4
Samsung Electronics
Reference Information
2. Reference Information
2-1 Tables of Abbreviations and Acronyms
Table 2-1 Abbreviations A Ah Å dB dBm °C °F °K F G GHz g H Hz h ips kWh kg kHz k km km/h kV kVA kW I MHz Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz MV MW M m µA µF µH µm µs µW mA mg mH mI mm ms mV nF pF Ib rpm rps s V VA W Wh Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour
Samsung Electronics
2-1
Reference Information
Table 2-2 Table of Acronyms ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor
2-2
Samsung Electronics
Reference Information
2-2 IC Line Up
2-2-1 100Hz
Table 2 - 3 IC Line - Up No. Block Name IC Location IC101 1 MAIN IC655 ICS801 IC301 2 SUB IC471 ICZ103,104 IC431 IC703 ICP706 IC701,702 3 TERMINAL IC705 ICP705 ICP707 ICP704 IC706 CS MODEL IC901 IC902 IC901 CW MODEL MICOM + TTX IC902 IC903 IC904 ICT01 ICT02 IC06 IC07 5 Double Window(D/W) IC01 IC02 IC03 Samsung Electronics IC Name SAA1300 TDA7265 TNY253P LA7845 TL494CN STK392-040 MC4558C PCF8574P PCF8574P(Option) TDA6920X TC4052BP TEA6422 TEA5114A TDA8601 PCF8591P Z9037116PS1 24C16 SDA30C264 27C040 8574 24C16 SDA5275 KM44C4004C SDA9361 CXA2101AQ VPC3230D-B2 SDP9400 SDS9280 2-3
4
MICOM
Reference Information
Table 2 - 3 IC Line - Up (Continued) No. Block Name IC Location PIC01 5 Double Window(D/W) PIC02 IC111,112 IC109,110 IC102 6 Convergence IC106,107,108 IC105 IC103 IC101 IC104 ICD601 7 Sound *ICD601 ICD602,603 8 CRT IC501,531,561 IC801S 9 POWER IC802 IC804 10 Sub AMP ICS601 IC Name VPC3230D-B2 MS81V04160 CD40668BCM 74HC4066 74HC4046 TL072 EL2210CS TSC87251G2D SDC91 AT82C64 MSP3452G-A1 MSP3450G-B6 TL062 TDA6111Q STRF6656 SVD001(OPTION) SE11ON TDA 7265 (DOLBLY, SULLOON,OPTION) IC01 IC02 11 Format Converter IC03 IC04 FS401S 416S11/20 Z9021106PSC 24C02 (PC,INPUT,OPTION)
2-4
Samsung Electronics
Reference Information
2-3 MICOM IIC BUS LINE -UP
Samsung Electronics
2-5
Reference Information
MENO
2-6
Samsung Electronics
Specifications
3. Specifications
Broadcasting System Scanning System
PAL MULTI 100HZ VHF : CH2 ~ CH13
Tuning Range
UHF : CH14 ~ CH69 Cable : CH1, CH14 ~ 125
Antenna Impedance
75 ohm Unbalanced Video : 38.9 MHz
Intermediate Frequency Sound : 33.4 MHz STD : 10W Sound Output Rated Voltage FULL MAX : 15W AC220V/AC110~250V/AC180~240V/50Hz CW 47" 55" Hx : 290 Lx : 290 Hx : 290 Lx : 290 Hy : 285 Ly : 285 Hy : 285 Hy : 285 Y : 8.0 Y : 0.3 Y : 7.5 Y : 0.25
White Balance
CS 43" 47" 55" Hx : 275 Lx : 258 Hx : 278 Lx : 268 Hx : 276 Lx : 267 Hy : 275 Ly : 255 Hy : 275 Hy : 262 Hy : 271 Hy : 258 Y : 9.5 Y : 0.4 Y : 8.25 Y : 0.29 Y : 7.9 Y : 0.29
High Voltage FUSE
29KV 250V/6.3A CODE NO : 3601-000300
Power Consumption
280W
Samsung Electronics
3-1
Specifications
3-1 TV Setup Mode
PC Enter
ZOOM
MAIN MENU COMPRESS
PC Enter
FREEZE SE T UP RESET EXIT
Switch to External Mode TV/External Key SETUP MENU T V SE T UP COMPUTER SETUP PICTURE SETUP EXIT
Switch to PC Mode Select Key T V SE TUP MENU H POS V POS RECALL EXIT SAVE AND EXIT LEFT DOWN SETTINGS RIGHT GROW UP GROW H SCALE SHRINK V SCALE SHRINK
Select menu F.Menu Key TV SETUP MENU H P OS L EF T RI GHT
Adjust screen left to balance Select TV Setup Volume+ key TV SETUP MENU Adjust horizontal position (left) Volume- key
Select TV Setup CH Down key TV SETUP MENU H SCA L E SHR INK GROW
H POS V P OS RECALL
LEFT DO WN SETTINGS
RIGHT GROW UP GROW Adjust screen top to balance Adjust vertical position (top) Volume + key SETUP MENU T V SE T UP COMPUTER SETUP PICTURE SETUP EXIT TV SETUP MENU V P OS DOWN UP
H SCALE SHRINK V SCALE SHRINK Adjust screen left to balance Adjust horizontal position (right) Volume - key TV SETUP MENU V SCAL E SHRI N K GROW EXIT SAVE AND EXIT
Select vertical position adjustment CH Down key T V SE TUP M EN U H POS V POS RECALL EXIT SAVE AND E XI T LEFT DOWN SETTINGS RIGHT GROW UP GROW H SCALE SHRINK
Adjust screen left to balance
V SCALE SHRINK
Adjust horizontal position (bottom) Volume+ key
. Save and Exit CH Down,Volume+ key
Exit
3-2
Samsung Electronics
Alignment and Adjustments
3-2 Picture Setup Mode
SETUP MENU TV SETUP COMPUTER SETUP P I CTU RE SE T UP EXIT P I CTURE SE TUP MENU BRIGHTNESS COLOR SATURETION FLICKER RECALL EXIT SAVE AND EXIT Select Picture Setup CH Down key Select Picture Setup Volume+ key Set in the bright screen Adjust brightness Volume+ key P I CTURE SETUP MENU BRIGHTNESS COLOR SATURETION FLICKER RECALL Set in the bright screen Adjust color saturation CH Down, Volume+ key EXIT Set in the bright screen Adjust flicker filter CH Down, Volume+ key MAIN MENU ZOOM TV SETUP COMPUTER SETUP P I CT URE SE T UP EXIT COMPRESS FREEZE SE T UP RESET EXIT Finish picture setup Volume+ key Finish Computer Setup F.Menu key Exit PC SAVE AND E XI T Save and Exit CH Down, Volume- key FILTER SETTINGS VIDEO FILTER FILTER SETTINGS VIDEO FILTER PICTURE SETUP MENU BRI GHT NE SS
PICTURE SETUP MENU COL OR SAT URAT I ON
PICTURE SETUP MENU F L I CKE R F I L T E R
SETUP MENU
1.
Adjust four different modes:VGA3 (VGA), VGA (DOS), VESA (SVGA), VEAS (XGA).
2). Perform the setup for each PC mode and picture setup.
Samsung Electronics
3-3
Alignment and Adjustments
3-3 Picture Setup Mode (computer setup mode only)
SETUP MENU TV SETUP COMP UT E R SE T UP PICTURE SETUP EXIT
COMPUTER SETUP MENU H P OS V POS RECALL EXIT SAVE AND EXIT L EF T DOWN SETTINGS RI GHT GROW UP GROW H SCALE SHRINK V SCALE SHRINK
COMPUTER SETUP MENU H P OS L EF T RI GHT
Adjust screen left to balance Adjust horizontal position (left) Volume- key
Select Computer Setup CH Down key
Select Computer Setup Volume+ key
COMPUTER SETUP MENU H SCAL E SHRI NK GROW
COMPUTER SETUP MENU H POS V P OS RECALL LEFT DOW N SETTINGS Adjust screen top to balance Adjust vertical position (top) Volume+ key RIGHT GROW UP GROW COMPUTER SETUP MENU V P OS DOW N UP H SCALE SHRINK V SCALE SHRINK
Adjust screen left to balance
EXIT SAVE AND EXIT Select vertical position adjustment CH Down key
Adjust horizontal position (right) Volume+ key
COMPUTER SETUP MENU V SCAL E SHRI N K GROW
COMPUTER SETUP MENU H POS V POS RECALL EXIT SAVE AND E XI T LEFT DOWN SETTINGS RIGHT GROW UP GROW H SCALE SHRINK
SETUP MENU TV SETUP COMPUT E R SE T UP PICTURE SETUP EXIT
Adjust screen left to balance
V SCALE SHRINK
Adjust horizontal position (bottom) Volume+ key
Save and Exit CH Down, Volume+ key
Exit
1. Adjust four different modes:VGA3 (VGA), VGA (DOS), VESA (SVGA), VEAS (XGA). 2. Perform the setup for each PC mode and picture setup.
3-4
Samsung Electronics
Alignment and Adjustments
4. Alignment and Adjustments
4-1 General Alignment Instructions
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 8. To protect against shock hazard, use an isolation transformer.
4-3 FACTORY MODE CONTROL
1. Enter & Concel the Factory Mode (1) Usual Remote Control Enter : PICTURE OFF -> DISPLAY KEY -> MENU KEY -> MUTE KEY -> POWER ON (Press each remote control key with in 3 seconds). Cancel : POWER OFF -> ON (2) Factory Remote Mode Enter : DISPLAY KEY -> FACTORY KEY (Press each remote control key with in 3 seconds). Cancel : POWER OFF -> ON Press the FACTORY key twice at intervals of at lease 1 second. (Enter the AGING Mode once) (3) Set Value When Entering the Factory Mode - Picture Mode & Sound Mode are set to the standard data. (4) Adjustments - CH.UP/DOWN Key : Use to select the item you want. - VOLUME UP/DOWN Key : Increases or decreases the value of data. - MENU Key : Use to save the current set value in EEPROM and exit to the upper mode. - Use the TV/VIDEO Key the conver to the AV Mode.
4-2 High voltage Check
CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level).
1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions.
Samsung Electronics
4-1
Alignment and Adjustments
4-4 FACTORY MODE MENU
4-4-1 CW MODEL
Service Mode Video Adjustment Y.C-Delay Deflection normal Deflection VGA Option byte Reset
VIDEO ADJUSTMENT
FUNCTION R Drive B Drive G Drive Gamma R Cutoff B Cutoff G Cutoff Sub Cont Sub Brt. Sub Color Sub Tint V Peaking TTX Cont TTX Bright PIP Cont PIP Bright CG R Contrast CG G Contrast CG B Contrast INITIAL DATA 31 31 31 12 31 31 31 7 31 7 7 7 10 10 0 0 40 40 40 RANGE 0 ~ 63 0 ~ 63 0 ~ 63 0 ~15 0 ~ 63 0 ~ 63 0 ~ 63 0 ~15 0 ~ 63 0 ~15 0 ~15 0 ~12 0 ~15 0 ~ 63 0 ~15 0 ~15 0 ~ 63 0 ~ 63 0 ~ 63 REMARK
4-2
Samsung Electronics
Alignment and Adjustments
Y.C-DELAY
FUNCTION PAL-B/G PAL-D/K/L PAL-I SECAM-B/G SECAM-D/K/L NTSC PAL-AV SECAM-AV NTSC-AV DVD INITIAL DATA 6 8 8 4 6 7 5 4 6 9 RANGE 0 ~15 0 ~15 0 ~15 0 ~15 0 ~15 0 ~15 0 ~15 0 ~15 0 ~15 0 ~15 REMARK
DEFLECTION NORMAL
FUNCTION P.V-SIZE P.V-SFT P.V-LIN P.S-CORR P.EW-WTH P.EW-PBL P.H-SFT P.EW-TPZ P.BOW P.ANGLE P.EW-UPCR P.EW-LOCR P.HOR-EHT P.VER-EHT P.INT. VOL. REF P.HSYNC DELAY INITIAL DATA -40 -39 0 0 +28 -27 -22 0 0 0 0 0 0 0 0 +10 RANGE -128 ~ +127 -128 ~ +127 -128 ~ +127 -128 ~ +127 -128 ~ +127 -128 ~ +127 -64 ~ +63 -128 ~ +127 -128 ~ +127 -128 ~ +127 -128 ~ +127 -128 ~ +127 0 ~ +255 0 ~ +255 -16 ~ +15 -128 ~ +127 REMARK
Samsung Electronics
4-3
Alignment and Adjustments
DEFLECTION NORMAL
FUNCTION P.PHP P.PVP P.PHS P.PVS P.CG V-AMP OFFSET INITIAL DATA 32 32 0 0 +30 RANGE 0 ~ 255 0 ~ 255 0 ~15 0 ~15 -128 ~ +127 REMARK
PICT. IMPROVE
FUNCTION LIMIT LEVEL SYSEM CLP-MSK ABL-MODE ABL-TH DTV-SYNC CR-OFFSET1 CB-OFFSET1 CR-OFFSET2 CB-OFFSET2 CTI-LEVEL R-Y/R R-Y/B G-Y/R G-Y/B LRGB2-LEVEL PABL-LEVEL BLK-BOTTOM SUB-SHP SUB-FO INITIAL DATA 0 1 0 1 1 69 10 10 7 7 1 3 7 15 2 7 15 15 3 2 RANGE 0~3 0~3 0~3 0~3 0~3 0 ~ 255 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0~3 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0~3 0~3 REMARK
4-4
Samsung Electronics
Alignment and Adjustments
PICT. IMPROVE
FUNCTION PRE-OVER LT1-LEVEL VM-LEVEL VM-DELAY DC-TRAN D-PIC DCTI BPF-LPF HPE-CORING INITIAL DATA 3 2 2 3 3 3 8 72 8 RANGE 0~3 0~3 0~3 0~3 0~3 0~3 0 ~ 255 0 ~ 255 0 ~ 255 REMARK
PICT. IMPROVE
FUNCTION SYSTEM CR-OFFSET1 CB-OFFSET1 R-Y/R R-Y/B G-Y/R G-Y/B SUB-SHP SUB-FO PRE-OVER LT1-LEVEL VM-LEVEL VM-DELAY DC-TRAN D-PIC INITIAL DATA 2 7 9 2 15 7 0 0 0 0 0 0 0 3 3 RANGE 0~3 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0~3 0~3 0~3 0~3 0~3 0~3 0~3 0~3 REMARK
Samsung Electronics
4-5
Alignment and Adjustments
PICT. IMPRV. SECA
FUNCTION CR-OFFSET1 CB-OFFSET1 R-Y/R R-Y/B G-Y/R G-Y/B INITIAL DATA 6 11 2 15 7 0 RANGE 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 REMARK
PICT. IMPRV. DVD
FUNCTION CR-OFFSET1 CB-OFFSET1 CT1-LEVEL DCTI BPF-LPF HPE-CORING INITIAL DATA 7 9 1 0 72 8 RANGE 0 ~ 15 0 ~ 15 0~3 0 ~ 255 0 ~ 255 0 ~ 255 REMARK
PICT. IMPRV. 480p
FUNCTION SYSTEM CLP-MASK DTV-SYNC CR-OFFSET1 CB-OFFSET1 CTI-LEVEL R-Y/R R-Y/B G-Y/R INITIAL DATA 0 0 0 0 0 0 0 0 0 RANGE 0~3 0~3 0 ~ 255 0 ~ 15 0 ~ 15 0~3 0 ~ 15 0 ~ 15 0 ~ 15 REMARK
4-6
Samsung Electronics
Alignment and Adjustments
PICT. IMPRV. 480P
FUNCTION G-Y/B SUB-SHP SUB-FO PRE-OVER LTI-LEVEL VM-LEVEL VM-DELAY DC-TRAN D-PIC INITIAL DATA 0 0 0 0 0 0 0 0 0 RANGE 0 ~ 15 0~3 0~3 0~3 0~3 0~3 0~3 0~3 0~3 REMARK
PICT. IMPRV. 1080
FUNCTION SYSTEM CLP-MSK DTV-SYNC CR-OFFSET1 CB-OFFSET1 CTI-LEVEL R-Y/R R-Y/B G-Y/R G-Y/B SUB-SHP SIB-FO PRE-OVER LTI-LEVEL VM-LEVEL VM-DELAY DC-TRAN D-PIC INITIAL DATA 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RANGE 0~ 3 0~ 3 0 ~ 255 0 ~ 15 0 ~ 15 0~ 3 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0~3 0~3 0~ 3 0~3 0~3 0~3 0~3 REMARK
Samsung Electronics
4-7
Alignment and Adjustments
SIM-826HEW OPTION-BYTE
OPTION BYTE CRT LANGUAGE GROUP LANGUAGE ATM SCRT/RCA VGA PLUG&PLAY DOLBY PROLOGIC PIP CW/CS LNA CHILD-LOCK HP JACK IDENT TOP TTX HIGH DEVIATION TTX GROUP GARRIER MUTE STANDARD SP47W3HF WIDE EUROPE ENGLISH ON SCART OFF ON ON ON CW ON ON OFF OFF ON W-EUROPE ON STANDARD SP55W3HF WIDE EUROPE ENGLISH ON SCART OFF ON ON ON CW ON ON OFF OFF ON W-EUROPE ON STANDARD SP65W3HF WIDE EUROPE ENGLISH ON SCART OFF ON ON ON CW ON ON OFF OFF ON W-EUROPE -> ICELANDIC -> HEBREW ON STANDARD ON <--> OFF STANDARD -> SPORT -> MILD -> NATURAL -> CUSTOM -> NDEN REMARK WIDE <--> 4:3 EUROPE <--> ASIA EIGHTEEN LANGUAGES ON <--> OFF SCART <--> RCA ON <--> OFF ON <--> OFF ON <--> OFF ON <--> OFF CW <--> CS ON <--> OFF ON <--> OFF ON <--> OFF ON <--> OFF ON <--> OFF E-EUROPE -> RUSSIAN -> ARABIC
4-8
Samsung Electronics
Alignment and Adjustments
4-4-2 CS MODEL
Service Mode Deflection Video Adjust1 Video Adjust2 NTSC OFFSET & CG DW PIP & OTHERS OPTION RESET
DEFLECTION
FUNCTION V Shift V AMP V Lin V SC V EHT H AMP Pin Phase Pin AMP Up Corner Low Corner H EHT H Shift V Angle V BOW H Sync Phase INITIAL DATA 124 134 11 104 0 161 143 70 128 128 0 80 124 128 128 RANGE 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 127 0 ~ 255 0 ~ 255 0 ~ 255 REMARK
Samsung Electronics
4-9
Alignment and Adjustments
VIDEO ADJUST1
FUNCTION Red Cutoff Green Cutoff Blue Cutoff Red Drive Green Drive Blue Drive Sub Bright Sub Contrast Sub Color Sut Tint RYR RYB GYR GYB Gamma P.YC Delay INITIAL DATA 31 31 31 31 31 31 31 7 15 7 3 7 15 2 12 7 RANGE 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 63 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0~8 REMARK
VIDEO ADJUST2
FUNCTION SUB Sharp Sharp FO Prev Over LT1 CT1 VM-Level VM-Delay DC-TRAN D Picture H Width INITIAL DATA 3 2 3 2 1 2 3 3 3 1 RANGE 0~3 0~3 0~3 0~3 0~3 0~3 0~3 0~3 0~3 0~3 REMARK
4-10
Samsung Electronics
Alignment and Adjustments
VIDEO ADJUST2
FUNCTION H Time Mask ABL Mode ABL TH TTX Position TTX Contrast VSU RGB Bright RGB Contrast Melody Volume INITIAL DATA 1 1 1 5 200 3 0 24 10 RANGE 0~3 0~3 0~3 0 ~ 40 0 ~ 255 0 ~ 15 0 ~ 127 0 ~ 63 0 ~ 20 REMARK
NTSC OFFSET & CG
FUNCTION Offset V Shift Offset V AMP Offset H AMP Offset H Shift Cg R Contrast Cg G Contrast Cg B Contrast Cg VAO PAL Cg VAO NTSC INITIAL DATA 2 0 6 4 100 60 10 24 24 RANGE -64 ~ 63 -64 ~ 63 -64 ~ 63 -64 ~ 63 0 ~ 100 0 ~ 100 0 ~ 100 0 ~ 100 0 ~ 100 REMARK
Samsung Electronics
4-11
Alignment and Adjustments
DW PIP & OTHERS
ITEM PIP VSTR PIP HSTR PIP Contrast DW 43 BCKPOS DW 43 BCKWID Cr offset1 Cb offset1 Cr offset2 Cb offset2 SDA9280 LPF SDA9280 BPF SDA9280 HPF SDA9280 SDA9280 0 X 05 D6:D4 CORING/PHACOM SDA9400 Y NR SDA9400 C NR SDA9400 0 X 1E D7:D4 SDA9400 0 X 10 D3:D0 4 15 15 0~7 0 ~ 15 0 ~ 15 0~7 0 ~ 15 0 ~ 15 FUNCTION VPC3230 0 X 0087 VPC3230 0 X 008A VPC3230 fp 0 X 0053 SDA9280 0 X 09 SDA9280 0 X 0A CXA2101 0 X 0F D7:D4 CXA2101 0 X 0F D3:D0 CXA2101 0 X 10 D7:D4 CXA2101 0 X 10 D7:D4 SDA9280 0 X 04 D6:D4 SDA9280 0 X 04 D3:D0 SDA9280 0 X 05 D3:D0 INITIAL DATA 7 7 48 148 61 10 10 7 7 4 12 10 RANGE 0 ~ 15 0 ~ 15 0 ~ 63 0 ~ 255 0 ~ 255 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0~7 0 ~ 15 0 ~ 15 REMARK 0 ~ 15 0 ~ 15 0 ~ 63 0 ~ 255 0 ~ 255 0 ~ 15 0 ~ 15 0 ~ 15 0 ~ 15 0~7 0 ~ 15 0 ~ 15
SIM-816HC OPTION-BYTE
OPTION BYTE SOUND WIDE SCART1 PC AUTO FM PIP HIGH DEVIATION SP43T6HF DOLBY OFF OFF ON ON DOUBLE ON SP47W3HF DOLBY OFF OFF ON ON DOUBLE ON SP55W3HF DOLBY OFF OFF ON ON DOUBLE ON REMARK DOLBY <--> A2/NICAM <--> V-DOLBY ON <--> OFF ON <--> OFF ON <--> OFF ON <--> OFF OFF <--> 1-TUNER <--> 2-TUNER <--> DOUBLE ON <--> OFF
4-12
Samsung Electronics
Alignment and Adjustments
4-4-3 W3 EU FACTORY DATA
VIDEO ADJUSTMENT
NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ITEM R Drive B Drive G Drive Gamma R Cutoff B Cutoff G Cutoff Sub Contrast Sub Bright Sub Color Sub Tint V Peaking TTX Contrast TTX Bright PIP Contrast Not used Cg R Contrast Cg G Contrast Cg B Contrast DEFAULT VALUE 29 (0 ~ 63) 36 (0 ~ 63) 32 (0 ~ 63) 8 (0 ~ 15) 31 (0 ~ 63) 15 (0 ~ 63) 32 (0 ~ 63) 15 (0 ~ 63) 28 (0 ~ 63) 9 (0 ~ 63) 9 (0 ~ 63) 8 (0 ~ 63) 7 (0 ~ 63) 0 (0 ~ 63) 43 (0 ~ 63) 31 (0 ~ 63) 31 (0 ~ 63) 15 (0 ~ 63) CONTROL IC CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 VPC3230 CXA2101 CXA2101 VPC3230 CXA2101 CXA2101 CXA2101
Y.C DELAY
NO 0 1 2 3 4 5 6 7 8 9 10 11 ITEM PAL-B/G PAL-D/K/L PAL-I SECAM-B/G SECAM-D/K/L NTSC PAL-AV SECAM-AV NTSC-AV RGB DVD YC DEFAULT VALUE 6 (0 ~15) 8 (0 ~15) 8 (0 ~15) 5 (0 ~15) 7 (0 ~15) 6 (0 ~15) 4 (0 ~15) 5 (0 ~15) 7 (0 ~15) 9 (0 ~15) 9 (0 ~15) CONTROL IC SDA9280 SDA9280 SDA9280 SDA9280 SDA9280 SDA9280 SDA9280 SDA9280 SDA9280 SDA9280 SDA9280
Samsung Electronics
4-13
Alignment and Adjustments
DEFIECTION NORMAL (When a PAL signal is input)
NO 0 1 2 3 4 5 6 7 8 9 ITEM P.V-Size P.V-Sft P.V-Lin P.V-Corr P.EW-Wht P.EW-Pbl P.H-Sft P.EW-Tpz P.Bow P.Angle DEFAULT VALUE -40 (-128 ~ 127) -34 (-128 ~ 127) 0 (-128 ~ 127) 0 (-128 ~ 127) 44 (-128 ~ 127) -27 (-128 ~ 127) 0 (-63 ~ 64) 0 (-128 ~ 127) 0 (-128 ~ 127) 0 (-128 ~ 127) 0 (-128 ~ 127) 0 (-128 ~ 127) 0 (0 ~ 255 0 (0 ~ 255) 0 (-16 ~ 15) 10 (-128 ~ 127) 7 (0 ~ 15) 7 (0 ~ 15) 30 (-128 ~ 127) CONTROL IC SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 VPC3230 VPC3230 SDA9361
DEFIECTION NORMAL (When a NTSC signal is input)
NO 0 1 2 3 4 5 6 7 8 9 ITEM N.V-Size N.V-Sft N.V-Lin N.V-Corr N.EW-Wht N.EW-Pbl N.H-Sft N.EW-Tpz N.Bow N.Angle DEFAULT VALUE -40 (-128 ~ 127) -34 (-128 ~ 127) 0 (-128 ~ 127) 0 (-128 ~ 127) 44 (-128 ~ 127) -27 (-128 ~ 127) 0 (-63 ~ 64) 0 (-128 ~ 127) 0 (-128 ~ 127) 0 (-128 ~ 127) 0 (-128 ~ 127) 0 (-128 ~ 127) 0 (0 ~ 255 0 (0 ~ 255) 0 (-16 ~ 15) 10 (-128 ~ 127) 7 (0 ~ 15) 7 (0 ~ 15) 30 (-128 ~ 127) CONTROL IC SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 SDA9361 VPC3230 VPC3230 SDA9361
10 P.EW-UpCr 11 P.EW-LoCr 12 P.Hor-EHT 13 P.Ver-EHT 14 P.Int.Vol.Ref 15 P.Hsync Delay 16 P.PIP H-Position 17 P.PIP V-Position 18 P.Not used 19 P.Not used 20 P.CG V-amp Offset
10 N.EW-UpCr 11 N.EW-LoCr 12 N.Hor-EHT 13 N.Ver-EHT 14 N.Int.Vol.Ref 15 N.Hsync Delay 16 N.PIP H-Position 17 N.PIP V-Position 18 N.Not used 19 N.Not used 20 N.CG V-amp Offset
4-14
Samsung Electronics
Alignment and Adjustments
PICT. IMPROVE
NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 ITEM Limit Level System CLP-MSK ABL-MODE ABL-TH DTV-SYNC Cr-Offset1 Cb-Offset1 Cr-Offset2 Cb-Offset2 CTI-Level R-Y/R R-Y/B G-Y/R G-Y/B LRGB2-Level PABL-Level BLK-Bottom SUB-SHP SUB-FO PRE-OVER LTI-Level VM-Levle VM-Delay DC-TRAN D-PIC DCTI BPF-LPF HPF-Coing DEFAULT VALUE 3 (0 ~ 3) 2 (0 ~ 3) 0 (0 ~ 3) 3 (0 ~ 3) 1 (0 ~ 3) 9 (0 ~ 255) 9 (0 ~ 15) 9 (0 ~ 15) 9 (0 ~ 15) 7 (0 ~ 15) 1 (0 ~ 3) 2 (0 ~ 15) 5 (0 ~ 15) 10 (0 ~ 15) 7 (0 ~ 15) 5 (0 ~ 15) 14 (0 ~ 15) 0 (0 ~ 15) 2 (0 ~ 3) 2 (0 ~ 3) 3 (0 ~ 3) 1 (0 ~ 3) 2 (0 ~ 3) 0 (0 ~ 3) 3 (0 ~ 3) 3 (0 ~ 3) 8 (0 ~ 255) 70 (0 ~ 255) 8 (0 ~ 255) DESCRIPTION Luminance signal edge enhancement setting Signal frequency band switching Switching of clamping pulse width in various ways Switching of ABL mode Adjustment of threshold voltage for ABL-IN input DTV-Sync For canceling the offset between CrCb of IN1and SEL IN systems For canceling the offset between CrCb of IN1and SEL IN systems For canceling the offset between CrCb of EXT systems For canceling the offset between CrCb of EXT systems Color difference signal edge enhancement setting R-Y axis +(R-Y) component setting R-Y axis -(B-Y) component setting G-Y axis -(R-Y) component setting G-Y axis -(B-Y) component setting LRGB2 system picture level control Setting of level detection DC at RGB-OUT of PEAK-ABL RGB-OUT bottom limiter level control(valid when BLKSW = 1) Sharpness center control Sharpness fo setting Presoot to overshoot ratio setting Luminance signal edge enhancement setting VM-OUT level control VM-OUT phase control Y system DC transmission ratio setting Dynamic picture(black expansion)control Digital Color Transition Improvement Control Luminance Peaking Control -Gain of band-pass filter -Gain of low-pass filter Luminance Peaking Control -Gain of high-pass filter -Gain of high-and band-pass filter CONTROL IC CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 SDA9280 SDA9280 SDA9280
Samsung Electronics
4-15
Alignment and Adjustments
PICT. IMPROVE
NO 29 30 ITEM NR-Luminance NR-Chrominace DEFAULT VALUE 8 (0 ~ 14) 6 (0 ~ 14) DESCRIPTION Luminance Noise Reduction Chrominance Noise Reduction CONTROL IC SDA9400 SDA9400
PICT. IMPROVE. VGA(NOT USED)
NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 ITEM System Cr-Offset1 Cb-offset1 R-Y/R R-Y/B G-Y/R G-Y/B SUB-SHP SUB-FO PRE-OVER LTI-Level VM-Level VM-Delay DC-TRAN D-PIC DEFAULT VALUE 2 (0 ~ 3) 9 (0 ~ 15) 9 (0 ~ 15) 2 (0 ~ 15) 5 (0 ~ 15) 10 (0 ~ 15) 7 (0 ~ 15) 2 (0 ~ 3) 3 (0 ~ 3) 3 (0 ~ 3) 1 (0 ~ 3) 2 (0 ~ 3) 0 (0 ~ 3) 2 (0 ~ 3) 3 (0 ~ 3) DESCRIPTION Signal frequency band switching For canceling the offset between CrCb of IN1 and SEL IN systems For canceling the offset between CrCb of IN1 and SEL IN systems R-Y axis +(R-Y) component setting R-Y axis -(B-Y) component setting G-Y axis -(R-Y) component setting G-Y axis -(B-Y) component setting Sharpness center control Sharpness fo setting Preshoot to overshoot ratio setting Luminance signal edge enhancement setting VM-OUT level control VM-OUT phase control Y system DC transmission ratio setting Dynamic picture(black expansion)control CONTROL IC CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101
4-16
Samsung Electronics
Alignment and Adjustments
PICT. IMPROVE. SECAM
NO 0 1 2 3 4 5 ITEM Cr-Offset1 Cb-offset1 R-Y/R R-Y/B G-Y/R G-Y/B DEFAULT VALUE 7 (0 ~ 15) 11 (0 ~ 15) 3 (0 ~ 15) 7 (0 ~ 15) 10 (0 ~ 15) 2 (0 ~ 15) DESCRIPTION For canceling the offset between CrCb of IN1 and SEL IN systems For canceling the offset between CrCb of IN1 and SEL IN systems R-Y axis +(R-Y) component setting R-Y axis -(B-Y) component setting G-Y axis -(R-Y) component setting G-Y axis -(B-Y) component setting CONTROL IC CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101
PICT. IMPROVE. RGB
NO 0 1 2 3 4 5 6 7 8 9 10 11 ITEM Cr-Offset1 Cb-offset1 DCT1 R-Y/R R-Y/B G-Y/R G-Y/B VM-Level VM-Delay V-PEAKING BPF-LPF HPF-Coring DEFAULT VALUE 9 (0 ~ 15) 9 (0 ~ 15) 0 (0 ~ 255) 2 (0 ~ 15) 5 (0 ~ 15) 10 (0 ~ 15) 7 (0 ~ 15) 0 (0 ~ 3) 0 (0 ~ 3) 0 (0 ~ 12) 72 (0 ~ 255) 10 (0 ~ 255) DESCRIPTION For canceling the offset between CrCb of IN1 and SEL IN systems For canceling the offset between CrCb of IN1 and SEL IN systems Digital Color Transition Improvement Control R-Y axis +(R-Y) component setting R-Y axis -(B-Y) component setting G-Y axis -(R-Y) component setting G-Y axis -(B-Y) component setting VM-OUT level control VM-OUT phase control Vertical Peaking Luminance Peaking Control -Gain of band-pass filter -Gain of low-pass filter Luminance Peaking Control -Gain of band-pass filter -Gain of low-pass filter CONTROL IC CXA2101 CXA2101 SDA9280 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 VPC3230 SDA9280 SDA9280
Samsung Electronics
4-17
Alignment and Adjustments
PICT. IMPROVE. DVD
NO 0 1 2 3 4 5 6 7 8 9 10 11 ITEM Cr-Offset1 Cb-offset1 DCT1 R-Y/R R-Y/B G-Y/R G-Y/B VM-Level VM-Delay V-PEAKING BPF-LPF HPF-Coring DEFAULT VALUE 9 (0 ~ 15) 9 (0 ~ 15) 0 (0 ~ 255) 2 (0 ~ 15) 5 (0 ~ 15) 10 (0 ~ 15) 7 (0 ~ 15) 1 (0 ~ 3) 0 (0 ~ 3) 0 (0 ~ 12) 72 (0 ~ 255) 10 (0 ~ 255) DESCRIPTION For canceling the offset between CrCb of IN1 and SEL IN systems For canceling the offset between CrCb of IN1 and SEL IN systems Digital Color Transition Improvement Control R-Y axis +(R-Y) component setting R-Y axis -(B-Y) component setting G-Y axis -(R-Y) component setting G-Y axis -(B-Y) component setting VM-OUT level control VM-OUT phase control Vertical Peaking Luminance Peaking Control -Gain of band-pass filter -Gain of low-pass filter Luminance Peaking Control -Gain of high-pass filter -Gain of high-and band-pass filter CONTROL IC CXA2101 CXA2101 SDA9280 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 VPC3230 SDA9280 SDA9280
PICT. IMPROVE. YC
NO 0 1 2 3 4 5 6 7 8 9 10 11 ITEM Cr-Offset1 Cb-offset1 DCT1 R-Y/R R-Y/B G-Y/R G-Y/B VM-Level VM-Delay V-PEAKING BPF-LPF HPF-Coring DEFAULT VALUE 9 (0 ~ 15) 9 (0 ~ 15) 0 (0 ~ 255) 2 (0 ~ 15) 5 (0 ~ 15) 10 (0 ~ 15) 7 (0 ~ 15) 1 (0 ~ 3) 0 (0 ~ 3) 0 (0 ~ 12) 72 (0 ~ 255) 10 (0 ~ 255) DESCRIPTION For canceling the offset between CrCb of IN1 and SEL IN systems For canceling the offset between CrCb of IN1 and SEL IN systems Digital Color Transition Improvement Control R-Y axis +(R-Y) component setting R-Y axis -(B-Y) component setting G-Y axis -(R-Y) component setting G-Y axis -(B-Y) component setting VM-OUT level control VM-OUT phase control Vertical Peaking Luminance Peaking Control -Gain of band-pass filter -Gain of low-pass filter Luminance Peaking Control -Gain of high-pass filter -Gain of high-and band-pass filter CONTROL IC CXA2101 CXA2101 SDA9280 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 VPC3230 SDA9280 SDA9280
4-18
Samsung Electronics
Alignment and Adjustments
P.STD CHANGE
NO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 ITEM STD Bright STD Contrast STC Color STD Sharpness STD Tint STD Colortone Sports Bright Sports Contrast Sports Color Sports Sharpness Sports Tint Sports Colortone Mild Bright Mild Contrast Mild Color Mild Sharpness Mild Tint Mild Colortone Natural Bright Natural Contrast Natural Color Natural Sharpness Natural Tint Natural Colortone VGA Bright VGA Contrast RGB Color RGB Color_L RGB Tint RGB Bri_Cont DEFAULT VALUE 32 (0 ~ 63) 42 (0 ~ 63) 32 (0 ~ 63) 32 (0 ~ 63) 0 (-31 ~ 31) 0 (0 ~ 4) 32 (0 ~ 63) 51 (0 ~ 63) 32 (0 ~ 63) 38 (0 ~ 63) 0 (-31 ~ 31) 3 (0 ~ 4) 35 (0 ~ 63) 32 (0 ~ 63) 32 (0 ~ 63) 28 (0 ~ 63) 0 (-31 ~ 31) 1 (0 ~ 4) 28 (0 ~ 63) 63 (0 ~ 63) 32 (0 ~ 63) 45 (0 ~ 63) 0 (-31 ~ 31) 3 (0 ~ 4) 32 (0 ~ 63) 32 (0 ~ 63) 5 (0 ~ 255) 209 (0 ~ 255) 0 (0 ~ 255) 27 90 ~ 255) DESCRIPTION Standard Mode Brightness Standard Mode Contrast Standard Mode Color Standard Mode Sharpness Standard Mode Tint Standard Mode Colortone Sports Mode Brightness Sports Mode Contrast Sports Mode Color Sports Mode Sharpness Sports Mode Tint Sports Mode Colortone Mild Mode Brightness Mild Mode Contrast Mild Mode Color Mild Mode Sharpness Mild Mode Tint Mild Mode Colortone Natural Mode Brightness Natural Mode Contrast Natural Mode Color Natural Mode Sharpness Natural Mode Tint Natural Mode Colortone Not used Not used RGB Mode Color RGB Mode Color RGB Mode Tint RGB Mode Brightness, Contrast CONTROL IC CXA2101 CXA2101 CXA2101 CXA2101 VPC3230 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 VPC3230 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 VPC230 CXA2101 CXA2101 CXA2101 CXA2101 CXA2101 VPC3230 CXA2101 CXA2101 CXA2101 VPC3230 VPC3230 VPC3230 VPC3230
Samsung Electronics
4-19
Alignment and Adjustments
P.STD CHANGE
NO 30 31 32 ITEM RGB Bri-Cont_L FB Gain Slicer Level DEFAULT VALUE 68 (0 ~ 255) 144 (0 ~ 255) 15 (0 ~ 255) DESCRIPTION RGB Mode Brightness, Contrast Fast Blanking Signal Gain Control Slicer Level Control CONTROL IC VPC3230 VPC3230 VPC3230
SIDE PANEL ADJUST
NO 0 1 2 3 4 ITEM Side Panel Pos. Side Panel Width Side Panel Level Side Panel B-Y Side Panel R-Y DEFAULT VALUE 153 (0 ~ 255) 69 (0 ~ 255) 7 (0 ~ 15) 0 (0 ~ 15) 0 (0 ~ 15) DESCRIPTION Side Panel Position Control Side Panel Width Control Side Panel Luminance Control Side Panel Chrominance Control Side Panel Chrominance Control CONTROL IC SDA9280 SDA9280 SDA9280 SDA9280 SDA9280
4-20
Samsung Electronics
Alignment and Adjustments
4-5 Screen Change (When adjusting I2C Bus Geometric items)
1
V SHIFT
6
V SIZE
2
V LINEARITY
7
V - S - CORRECTION
3
H SIZE
8
PIN PHASE
4
PIN AMP
9
H SHIFT
5
V ANGLE
10
V BOW
Samsung Electronics
4-21
Alignment and Adjustments
4-6 Other Adjustments
4-6-1 Screen Adjustment
1. Warm up the TV for at least 30 minutes. 2. Turn to the Video Mode (No Signal) using a remote-control. 3. Connect an oscilloscope to RK,GK,BK. 4. Adjust the VR (VR501, VR531, VR561) screen so that RK, GK, BK pulse is 20Vp-p each. (Turn the R,G,B VR screen fully counterclockwise in the area of each flyback line.) 3. Select SBT by pressing the Volume +/- keys. 4. Adjust so that the 63 step on the right side of the screen is not seen (Use the Volume +/keys). 5. Press the Menu key to exit.
4-6-4 High Voltage (29KV) Check
PRECAUTION
1. Input a lion head pattern. 2. Select "STANDARD" video mode.
4-6-2 White Balance Adjustment
3. Warm up the TV for at least 10 minutes. 1. Select the "STANDARD" video mode. 4. Use a 1000:1 probe. 2. Input 100% white pattern. 3. In the stand-by mode, press the remote-control keys in the following sequence: Displsy Menu Mute Power ON 4. Warm up the TV for at least 30 minutes. 5. Input a 10-step signal. 6. R-cut off, B-cut off, and G-cut off by pressing the Volume +/- keys. 7. Adjust the low light with viewing the dark side of the screen. 8. Select R-drive, G-drive, and B-drive by pressing the Volume +/- keys. 9. Adjust the high light with viewing the light side of the screen. 10. If necessary, redo adjustments 6~9. 11. Press the Menu key to exit. 3. Adjust VR (RR402S) so that the voltage becomes 2.25V. After the adjustments are complete, be sure to mount VR (RR402S) correctly.
ADJUSTMENT
1. Connect the (+) terminal of the 1000:1 probe to the high voltage distributor and the (-) terminal to GND (located on the deflection board). 2. Adjust RR471S (located on the deflection board) so that the digital meter indicates DC 29V ± 0.1V.
4-6-5 F.S. (Fail Safe) Adjustment
Note : The finished product has a well-mounted VR (RR402S). If necessary, do the F.S. adjustments in the following sequence. 1. 2. Use a digital multimeter. Connect the digital multimeter to the JIG pin (DZ482S) terminals
4-6-3 Sub-Brightness Adjustment
4. 1. Input a sub-brightness adjustment signal. (TOSHIBA PATTERN) 2. In the stand-by mode, press the remote-control keys in the following sequence : Displsy Menu Mute Power ON
4-22
Samsung Electronics
Alignment and Adjustments
4-6-6 F.S. (Fail Safe) Circuit Check
Note : The F.S. Circuit check must be performed after servicing. 1. Turn on the TV. 2. Select the "STANDARD" video mode. 3. Short F/S Test point (located on the SUB PCB). Then, both sound and picture disappear. (Note: Even if the shorted terminals are removed, both sound and picture do not appear. This proves the F.S. circuit is working. ) 4. To restore both sound and picture, turn off the TV and reset it after about 30 seconds.
4-6-8 Lens Focus Adjustment
PRECAUTIONS
1. Do this adjustment after the static focus adjustment and the tilt adjustment. 2. Select the "STANDARD" video mode. (Contrast:100, Brightness:50) 3. Input a crosshatch pattern.
ADJUSTMENT
1. Loosen the lens screws. 2. Cover the two lenses that are not being adjusted. 3. Adjust the lens, observing the color aberration vertically and horizontally within 3 blocks of the center of the crosshatch pattern. 4. When the lens is turned clockwise, the color aberration will change as follows: Lens R G B Color Aberration Change Orange - Crimson Blue - Red Purple - Green
4-6-7 Static Focus Adjustment
PRECAUTION
1. Select the "STANDARD" video mode. 2. Input a crosshatch pattern. 3. Cover the lenses that are not being adjusted. 4. Connect a convergence jig and read data. 5. Adjust the lens for best focus. (See Fig, 4-1, next page)
STATIC FOCUS (CONTINUED)
Vary the focus pack VR (Red, Blue) on the front cabinet. Adjust the TV for best possible focus around the center of the crosshatch pattern, without losing overall screen balance. Figure Crosshatch Pattern Examine these points together.
5. Green lens adjustment: Set the lens at the point where Blue just changes to Red. If the color aberration is irregular throughout the picture screen, adjust the lens to show Red color aberration (approximately 1~3 mm area) within a 3-block grid around the horizontal center-line. If the color aberration is irregular, adjust the lens as shown in the diagram below. (Accurate alignment of Green is important for overall color quality.) 6. Red lens adjustment Set the Red lens at the point where Orange becomes Crimson. 7. Blue lens adjustment Set the Blue lens at the point where Purple becomes Green.
Examine these points together
P L1 L2
Fig. 4-1 Crosshatch Pattern.
RED ABERRATION BLUE ABERRATION < L1, L2_ P
Fig. 4-2 Color Aberration Samsung Electronics 4-23
Alignment and Adjustments
4-6-9 Horizontal Dynamic Focus Adjustment
PRECAUTION
1. Input a crosshatch pattern. 2. Select the "STANDARD" video mode. 3. Warm up the set for at least 10 minutes.
ADJUSTMENT
1. Cover the Red and Blue lenses. 2. Use a digital multimeter.
3. Connect the '+' terminal of digital multimeter to D-Focus and the '-' terminal to GND. 4. Adjust L434 located on the sub PCB so that the digital multimeter indicates AC690 20Vp-p.(WIDE AC600 20Vp-p) 5. Balance the left and right sides of the dynamic focus lines.
4-24
Samsung Electronics
Alignment and Adjustments
4-7 SCREEN-JIG
4-7-1 43T6 Normal Mode
N o r mal 4 :3 M o d e Sc reen Size : X 873, Y 655 (X:378= 9*2+ 30* 12, Y: 440=28*2+ 64* 6) 2 0 .7 9 m m 6 9 .2 9 m m 2 0 .7 9 m m
4 1 .6 8 m m
9 5 .2 7 m m
4 1 .6 8 m m
4-7-2 54T6 Normal Mode
N o r m al 4 : 3 m o d e Sc reen Size : X 1098.4, Y 827.4 (X :378=9* 2+ 30*12, Y:440=28* 2+ 64* 6) 2 6 .1 5 m m 8 7 .1 7 m m 2 6 .1 5 m m
5 2 .6 5 m m
1 2 0 .3 5 m m
5 2 .6 5 m m
Samsung Electronics
4-25
Alignment and Adjustments
4-7-3 47W3 Normal Mode
N o r m al 4 : 3 m o d e Sc reen Size : X 1045, Y 588 (X:378= 9* 2+ 30* 12, Y: 440=28*2+ 64* 6) 2 4 .8 8 m m 8 2 .9 4 m m 2 4 .8 8 m m
3 7 .4 2 m m
8 5 .5 3 m m
3 7 .4 2 m m
4-7-4 55W3 Normal Mode
N o r m al 4 : 3 m o d e Sc reen Size : X 1225, Y 686 (X:378= 9* 2+ 30* 12, Y: 440=28*2+ 64* 6) 29.17mm 97.22mm 29.17mm
43.65mm
99.78mm
43.65mm
4-26
Samsung Electronics
Alignment and Adjustments
4-7-5 65W3 Normal Mode
N o r m al m o de Scr een Size : X 1442, Y 838 (X :378=9* 2+ 30*12, Y:440= 28* 2+ 64* 6) 3 4 .3 3 m m 1 1 4 .4 4 m m 3 4 .3 3 m m
5 3 .3 3 m m
1 2 1 .8 9 m m
5 3 .3 3 m m
Samsung Electronics
4-27
Alignment and Adjustments
4-8 Remote Control for Servicing
4-8-1 WESTERN EUROPE
Power
4-28
Samsung Electronics
Alignment and Adjustments
4-8-2 CHINA
Power
Samsung Electronics
4-29
Alignment and Adjustments
4-8-3 KEY Function
1. R-SELECT Press to select RED color. 2. G-SELECT Press to select GREEN color. 3. B-SELECT Press to select BLUE color.
4. R-MUTE Press to mute RED color. 5. G-MUTE Press to mute GREEN color. 6. B-MUTE Press to mute BLUE color. 7. CANCEL KEY Press to revert to the previous data during the Convergence Adjustment. 8. TEST/NORMAL Press to check TV mode in the Convergence Mode. 9. LINE SHIFT Press to move a line up/down or left/right. 10. FACTORY DATA SELECT BUTTON Press to call the factory default values. 11. H/V DIRECTION SELECT BUTTON Press to switch the cursor direction horizontally or vertically. 12. SAVE BUTTON After the Convergence Adjustments are completed, press to save data. 13 EXIT BUTTON After the Convergence adjustments are completed, press to exit to TV mode.
4-30
Samsung Electronics
Alignment and Adjustments
14. MOVE CURSOR FORWARD Press to move the cursor right or down. 15. MOVE CURSOR REVERSE JOYSTICK(Option Press to move the cursor left or up. 16. CONVERGENCE PICTURE MOVE BUTTON )
17. CONVERGENCE MOVE BUTTON Press to move the convergence left (
) or right (
).
18. CONVERGENCE DATA ZERO BUTTON Press to zero the convergence correction data. 19. INITIAL DATA SET BUTTON Changes when applying Almighty-Cg, Module (How to extract the basic Cg Data) Model Name Inch (Type) Representative Model SP43T6 SP54T6 SP62T6 SP47W3 SP55W3 SP65W3 Basic Data Number after entring the Cg-Mode 5-436 (Press in regular order) 5-546 (Press in regular order) 5-626 (Press in regular order) 5-479 (Press in regular order) 5-559 (Press in regular order) 5-659 (Press in regular order) Screen Display Discription
43" (43T6) 54" (54T6) 62" (62T6) 47"(47W3) 55"(55W3) 65"(65W3)
White Oval on the background (white circle) White Oval on the background (white border) White Oval on the background (white circle) White Oval on the background (white border)
20. Data Shift Button
Press to transmit data(PAL Mode/NTSC Mode)
Samsung Electronics
4-31
Alignment and Adjustments
4-9 Convergence Adjustment
Special Notes A sensor is attached on the center of each side of the Convergence Mode pattern (see figure below). The sensors are required for normal Perfect Focus function. Use a screen jig to do the convergence adjustments correctly (Especially, perform correct convergence adjustments on the center of each side where a sensor is located.) Do the convergence adjustments correctly. Otherwise, any Perfect Focus error can happen.
1. Warm up the TV for a least 30 minutes. 2. Input an PAL Signal.(Use an antenna or AV source.)
Make sure that deflection yoke are properly adjusted so that the center of Green, Red, Blue pattern is aligned on the center of screen jig.
3. Enter the Convergence Mode by Pressing the remote control keys in the following sequence:
If OSD displayed as shown in figure below, press the key to exit. Then, redo step 3 to enter the Convergence Mode. After entering the Convergence Mode, Stand by for about five seconds before doing the adjustments.
4-32
Samsung Electronics
Alignment and Adjustments
Samsung Electronics
4-33
Alignment and Adjustments
4-34
Samsung Electronics
Samsung Electronics
4-35
Alignment and Adjustments
4-36
Samsung Electronics
Alignment and Adjustments
4-10 MICOM and Pins Voltage
4-10-1 Pin Layout(CW)
AMP MUTE CENTER RESET BUS-STOP KEYS1 KEYS2 MAIN AFT SUB AFT VSSA A3 VDDA M3L CLK M3L DATA M3L ENABLE
RXD IR
P0.5 P0.6 P0.7 P2.3 P2.2 P2.1 P2.0 VSSA A3 VDDA P3.7 P3.6 P3.5 P3.4 P3.3 P3.2
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
D1 D2 D3 PROTECT ST-BY LED1 TIMER LED2 POWER POWER2 TXD VSS VDD XTAL2 XTAL1 RESET NC A16
P3.1 P3.0 P1.6 P1.5 P1.4 P1.3 P1.2 P1.1 P1.0 VSS VDD XTAL2 XTAL1 RST ALE A16
SDA30C264
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
P0.4 WP P0.3 SCL2 P0.2 SDA2 P0.1 SDA1 P0.0 SCL1 P4.1 A18 P4.0 A17 VDD VDDD VSS VSSD A2 A2 A1 A1 A0 A0 D3 D3 D2 D2 D4 D4 D1 D1
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
A15 A15 A14 A14 A12 A12 A13 A13 A7 A7 A8 A8 A6 A6 A5 A5 A11 A11 A4 A4 A10 A10 D7 D7 D6 D6 D0 D0 D5 D5
Samsung Electronics
4-37
Alignment and Adjustments
4-10-2 MICOM Pins(CW)
PIN NO.
ITEM
FUNCTION
OUT VOLT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
D1 D2 D3 PROTECT ST-BY LED TIMER LED POWER POWER2 TXD VSS VDD XTAL2 XTAL1 RESET NC A16 A15 A14 A12 A13 A7 A8 A6 A9 A5 A11
D1 D2 D3 PROTECT ST-BY LED TIMER LED POWER POWER2 TXD VSS VDD XTAL2 XTAL1 RESET NC A16 A15 A14 A12 A13 A7 A8 A6 A9 A5 A11
4-38
Samsung Electronics
Alignment and Adjustments
PIN NO.
ITEM
FUNCTION
OUT VOLT
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
A4 D10 D7 D6 D0 D5 D1 D4 D2 D3 A0 A1 A2 VSS VDD A17 A18 SCL1 SDA1 SDA2 SCL2 WP AMP-MUTE CENTER-MUTE BUS-STOP KEY1
A4 D10 D7 D6 D0 D5 D1 D4 D2 D3 A0 A1 A2 VSS VDD A17 A18 SCL1 SDA1 SDA2 SCL2 WP AMP-MUTE CENTER-MUTE BUS-STOP KEY1
Samsung Electronics
4-39
Alignment and Adjustments
PIN NO.
ITEM
FUNCTION
OUT VOLT
53 54 55 56 57 58 59 60 61 62 63 64
KEY2 MAIN-AFT SUB-AFT VSS A3 VDD M3L CLK M3L DAT M3L ENABLE NC RXD IR
KEY2 MAIN-AFT SUB-AFT VSS A3 VDD M3L CLK M3L DATA M3L ENABLE NC RXD IR
4-40
Samsung Electronics
Alignment and Adjustments
4-10-3 Pin Layout(CS)
W.P SDA2 SCL2 BUS-STOP SDA1 SCL1 S-RESET V-MUTE VDD 2.5V GND VDD 3.3V CVBS IN VDD 2.5V GND AFT SUB-AFT KEY2 KEY1 H-BLK V-BLK KEY3 PROTECT SCONT1 IR-IN D3 TIMER LED
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
52 51 50 49 48 47 46 45
SCONT 0 POWER 2 POWER S-MUTE DVD-CTL LENTER SPK-MUTE DTV-ID DVD-ID VDD 3.3V GND VDD 2.5V OSD F/B OSD B OSD G OSD R VDD 2.5V GND X-OUT X-IN RESET D1 D2 VDD 3.3V GND RTXD ST-BY LED
S D A 5 5 5 X
44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
Samsung Electronics
4-41
Alignment and Adjustments
4-10-4 MICOM Pins(CS)
PIN NO.
ITEM
FUNCTION
OUT VOLT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
W.P SDA2 SCL2BUS-STOP SDA-1 SCL-1 S-RESET V-MUTE VDD GND VCC CVBS VDD GND MAIN-AFT SUB-AFT KEY2 KEY1 HSYNC VSYNC KEY3 PROTECT S-CONTO IR IN D3 TIMER-LED I2 BUS STOP DATA BUS LINE CLOCK BUS LINE SOUND RESET VIDEO SIGNAL MUTE VDD 2.5V GND VCC 3.3V CVBS IN VDD 2.5V GND MAIN TUNER AFT SUB AUTO FINE TURNING CONTROL KEY SCAN 2 KEY SCAN 1 HORIZONTAL SYNC INPUT VERTICAL SYNC INPUT KEY SCAN 3 PROTECT PORT SOUND MODE SELECT REMOCON INPUT CONVERGENCE D3 TIMER LED
4-42
Samsung Electronics
Alignment and Adjustments
PIN NO.
ITEM
FUNCTION
OUT VOLT
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
ST-BY-LEDD RXD GND VDD D2 D1 /RESET XTAL1 XTAL2 GND VDD OSD R OSD G OSD B OSD F-B VDD GND VDD DVD-IDENT DTV-INENT CENTER MODE SELECT AMP-MUTE POWER
LED GND VDD 3.3V DATA BUS LINE CLOCK BUS LINE RESET XTAL1 XTAL2 GND VDD 2.5V ON SCREEN DISPLAY RED OUTPUT ON SCREEN DISPLAY GREEN OUTPUT ON SCREEN DISPLAY BLUE OUTPUT OSD BLAKING SIGNAL OUTPUT VDD 2.5V GND VDD 3.3V DVD-IDENT DTV-IDENT SPK MUTE DVD MODE SELECT(480i/480p) MAIN AMP MUTE POWERR ON/OFF RELAY CONTROL
S-CONTO
SOUND MODE SELECT
Samsung Electronics
4-43
Alignment and Adjustments
4-10-5 Proscan Module (CS)
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 ITEM Pr/R Y/G Pb/B FB GND HC VS1 GND SDA SCL 5V 27M GND 5VH-OUT V-OUT SCP EW V-BLK ABL ADAD+ H-BLK HD GND PIP-RF PIP-C PIP-V/Y GND CVBS-Y GND EAST WEST OUT V-BLANKING ABL INPUT VERTICAL DRIVE(-VOLTAGE) VERTICAL DRIVE(+VOLTAGE) H-BLANKING INPUT H-DRIVE OUT GND FUNCTION Pr/R INPUT Y/G INPUT Pb/B INPUT FAST BLANKING INPUT GND 5V INPUT VS1 INPUT GND SERIAL DATA LINE SERIAL CLOCK LINE 5V OPTION GND 5VHORIZENTAL-OUT VERTICAL-OUT OUT VOLT 2.0V 2.0V 2.0V 0.25V 4.7V 4.8V 5V GND 5VN.C N.C 2.2V 2.15V 2.95V 2.90V 1.6V GND GND -
4-44
Samsung Electronics
Alignment and Adjustments
PIN NO. 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ITEM CHR GND PC-R PC-G PC-B PC-H PC-V GND OSD-R OSD-G OSD-B YS/YM YS/YM GND 9V HD-Pr HD-Y HD-Pb GND R-OUT G-OUT B-OUT GND IK GND GND VM-Y YD GND CG-SYND
FUNCTION CHROMA GND N.C N.C N.C GND OSD-R INPUT OSD-G INPUT OSD-B INPUT BLANK(MICOM OUT) HALF TONE INPUT VIDEO MUTE (V-CHIP ON) GND 9V D-Pr INPUT D-Y INPUT D-Pb INPUT N.C GND GND R-OUT G-OUT B-OUT GND IK OUT SPOT OUT GND VM-Y OUT N.C GND CG-SYNC INPUT
OUT VOLT GND GND 4.72V GND 9V -
GND 3.65V GND 5.42V GND -
Samsung Electronics
4-45
Alignment and Adjustments
PIN NO. 61 62 63 64
ITEM CG-B CG-G CG-R GND
FUNCTION CG-B INPUT CG-G INPUT CG-R INPUT GND
OUT VOLT GND
4-46
Samsung Electronics
Alignment and Adjustments
4-10-6 Sound Module
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
ITEM GND GND GND S-RESET MAIN-L GND GND 5V MAIN-R GND GND GND 8V SCL-1 GND SDA-1 CENTER GND GND 12V SURROUND GND GND S-F1 GND GND AV4-L-IN A-MONO-IN GND GND GND GND GND SOUND RESET MAIN LEFT OUT GND GND 5V
FUNCTION
OUT VOLT GND GND GND GND GND 5V GND GND GND 8V GND GND GND 12V GND GND GND GND GND GND
MAIN RIGHT OUT GND GND GND 8V SERIAL CLOCK LINE GND SERIAL DATA LINE CENTER OUT GND GNAD 12V SURROUND OUT GND GND S-F1(ANT1) GND GND AV4 LEFT INPUT A-MONO INPUT GND GND
Samsung Electronics
4-47
Alignment and Adjustments
PIN NO. 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
ITEM AV4-R-IN S-F2 GND GND GND GND EXT-L-IN H-PHONE-L GND GND EXT-R-IN H-PHONE-R GND GND GND GND AV2-L-IN MONITOR-L GND GND AV2-R-IN MONITOR-R GND GND GND GND AV1-L-IN AV1-L-OUT GND GND
FUNCTION AV4 RIGHT INPUT S-F2(ANT2) GND GND GND GND EXTERNAL LEFT INPUT HEADPHONE LEFT OUT GND GND EXTERNAL RIGHT INPUT HEADPHONE RIGHT OUT GND GND GND GND AV2 LEFT INPUT MONITOR OUT GND GND AV2 RIGHT INPUT MONITOR OUT GND GND GND GND AV1 LEFT INPUT AV1 LEFT OUTPUT GND GND
OUT VOLT GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND
4-48
Samsung Electronics
Alignment and Adjustments
PIN NO. 61 62 63 64
ITEM AV1-R-IN AV1-R-OUT GND GND
FUNCTION AV1 RIGHT INPUT AV1 RIGHT OUT GND GND
OUT VOLT GND GND
Samsung Electronics
4-49
Alignment and Adjustments
4-10-7 CONV-Module
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
ITEM 6V GND FOCUS GND D2 D1 GND C-SYNC R TEST-Y/G B D3 CTRL IR COMP GND GND GND BV BH GV GH RV RH GND H-BLK V-BLK GND N.C -5.4V 6V GND N.C GND SDA SCL GND
FUNCTION
OUT VOLT 6V GND GND GND 4.41V 0.2V 3V GND GND GND GND 0.52V GND -5.4V
C-SYNC OUT WHEN TEST PATTERN R OUT WHEN TEST PATTERN G OUT WHEN TEST PATTERN B OUT D3/NT-PAL SEL CTRL INPUT REMOCON COMP VIDEO OUTPUT GND GND GND BLUE VERTICAL OUT BLUE HORIZONTAL OUT GREEN VERTICAL OUT GREEN HORIZONTAL OUT RED VERTICAL OUT RED HORIZONTAL OUT GND H-BLANKING OUT V-BLANKING OUT GND N.C -5.4V
4-50
Samsung Electronics
Alignment and Adjustments
PIN NO. 31 32
ITEM 5.4V GND 5.4V GND
FUNCTION
OUT VOLT 5.4V GND
Samsung Electronics
4-51
Alignment and Adjustments
MENO
4-52
Samsung Electronics
Troubleshooting
5. Troubleshooting
5-1 Convergence Misaligned
Normal
Check the output voltage and waveform of CN801, 803, CNZ02 on the Convergence Board
Abnormal
Check CNZ01 out pin (BZ, BH, RV, RH, GV, GH)
Abnormal
Normal
Check the associated circuitry
Check Convergence Moudle
1. Check FD802S, FD855S, FD805S, FD806S On the Power Board 2. Check the output from H-BLK, V-BLK the Main Board
Samsung Electronics
5-1
Troubleshooting
5-2 No Sound
Check if CN601 is inserted normal Check IC665 output pins 2, 4 Abnormal Check IC665 input pin 5 normal Check IC665 Mute pin 5 normal Check IC665 output pins 7, 11 Abnormal Check IC601 input pins 35, 38 Abnormal Check CNS01 input pins 5, 9 Abnormal Check IC703 input pins Abnormal Check CNS01 output pins 28
Abnormal Insert CN601 (Connector) normal Check Speaker
Abnormal Check FD854S on the Power Board Abnormal Check the Mute circuit
normal Check the Control
normal Check the Control
normal Check the Sound Module circuit normal Check IC703
5-2
Samsung Electronics
Troubleshooting
5-3 No Raster (Sound OK)
Normal
Check Heater
Check High Voltage Normal
Check CRT PCB pin 1 Normal Normal Check IC501, 531, 561 Abnormal Check CN501 (Connector) Normal Check CN01
Abnormal
Check Q473, R437A Normal
Check CN501 pins 1, 3, 5 Normal Check CN501 (Connector) Normal Check CN01 inpur pins 30, 31 Abnormal Check CNT02 input pins 19, 21 Abnormal
Check Q473 HV-REG Abnormal Check Q473, IC471 Abnormal Check HV-OUT BLOCK
Check Q472 input pin "G"(HV-DRIVER) Normal
Check HV-OUT BLOCK
Normal Check CNT02
Check IC02 input pin 24 Abnormal Check IC701 input pin 8 Abnormal Check CN01
Normal Check IC02
Normal
Check IC701
Samsung Electronics
5-3
MEMO
5-4
Samsung Electronics
Exploded View & Parts List
6. Exploded View & Parts List
6-1 SP47W3HFX
No 1 2 3 4 5 5 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Code No Description;Specification TAPE-OPP MASKING SPACER-COVER,DUST;W3,PS SHEET,T0.35 BRACKET-CRT,MAIN;54,SECC,T1.6,-,-,-,GUIDE-FLOW;54J8,J7,ABS,-,-,-,BLK,HB HOLDER-SCREEN,R;47H1,ABS HB,GRAY HOLDER-SCREEN,TB;W3,W1,ABS HB,L1102,BLK, HOLDER-SCREEN,L;47H1,ABS HB,GRAY CABINET-BACK,BOT;47W3,HIPS HB,BLK CABINET-BACK,TOP;47W3,HIPS HB,BLK,DO CABINET-BACK,SIDE;47.55W3,HIPS HB,BLK,DO SCREEN-TINT;47W,1070*612,T=0.7,P=0.52 SCREEN-FRESNEL;47W,-,T2,1072*614,-,-,-,SUN SCREEN-AG;47W,-,T=82%,1072*614*2,-,MIRROR-FRONT;47W3,GLASS ,861*677*421,FSM BRACKET-MIRROR;47W3,SECC,T1.0 ASSY CHASSIS;SP47W3HFX/BWT ASSY-C/FRONT,MASK;,HB GRAY,SVM1126 TANTU DOOR-RACK;47.55.65W3,HIPS HB,GRAY,SV808P ASSY-CABINET,WOOD;,WOOD,CIS,47W3 ASSY SUB-PCB,A/V TERMINAL;W3,J52A,RUSSIA ASSY-C/FRONT,BOT;,HB GRAY,SV808P+SVM1126 ASSY-CENTER,SPK;,W3 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 S.N.A S.N.A S.N.A S.N.A S.N.A S.N.A S.N.A S.N.A Q'ty S.N.A Remark
Samsung Electronics
6-1
Exploded View & Parts List
6-2 SP55W3HFX
No 1 2 3 4 5 6 8 9 10 10 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Code No Description;Specification ASSY-C/FRONT,MASK;,HIPS HB,GRAY SVM1126 ASSY-C/FRONT,BOT;,HIPS HB,GRAY SV808P+SV ASSY-DOOR,RACK;,HB GRAY,SV808P+SVM1126,W ASSY-CENTER,SPK;,W3 SUN SCREEN-AG;55W,-,T=82%,1251*712*2,-,SCREEN-FRESNEL;55W,-,T2,1251*712,-,-,-,ASSY-CABINET,WOOD;,WOOD M-EAST,55W3 CABINET-BACK,SIDE;47.55W3,HIPS HB,BLK,DO HOLDER-SCREEN,TB;55W3,ABS HB,L1282,BLK HOLDER-SCREEN,L;55W3,ABS HB,BLK HOLDER-SCREEN,R;55W3,ABS HB,BLK ASSY SUB-PCB,A/V FRONT;SP47W3HFX/XEG,J52 ASSY CPT-B;P16LSG03BMB,55,+380MGSSM-100 SPACER-COVER,DUST;W3,PS SHEET,T0.35 MIRROR-FRONT;55W9,FSM,1027*799*540 BRACKET-FRAME,MIRROR L;55W9,SECC,T1.6,BL BRACKET-FRAME,MIRROR R;55W9,SECC,T1.6,BL SPACER-MIRROR,TOP;50J6,PVC HB,BLK,L1020 SPACER-MIRROR,L;50J6,PVC HB,BLK,L1020 SPACER-MIRROR,BOT;50J6,PVC HB,L799,BLK SPACER-MIRROR,R;50J6,PVC HB,BLK,L1020 BRACKET-MIRROR,BOT;55W9,SECC,T1.0 BRACKET-MIRROR,TOP;55W9,SECC,T1.0,BLK CABINET BACK-TOP;55W3,PS SHEET,T4.0 CABINET BACK-BOT;55W3,HIPS HB,BLK ASSY CHASSIS;SP55W3HFX/BWT Q'ty 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 S.N.A Remark
6-2
Samsung Electronics
Electrical Parts List
7. Electrical Parts List
7-1 SP47W3HFX/BOB
Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
AA59-00220A AA94-03599A AA94-03600A AA94-03601A 0203-001329 AA02-00022A 6005-001004 6001-000137 6003-001019 6003-001026 6005-001003 6005-001005 6006-001094 AA60-00132A AA60-10011A AA61-00617B AA61-00859A AA91-00921A AA91-00921B AA61-00972B AA61-00049B AA73-00005B AA63-10007C AA63-60131A AA63-70002A AA64-01395Q AA64-02336A AA64-02074D AA64-02224B AA64-02225B AA64-60449B AA65-30008A AA67-00196A AA67-00119B AA67-00136A AA67-00165A AA69-00744L AA69-01227B AA69-01298A AA69-01299E AA73-00008A AA91-00773A AA91-03555A AA94-11168D AA95-01841C AA95-01790K AA95-01847G AA95-01785E AA94-11166E AA95-01753D AA96-20130A 0201-001059 AA26-00101A AA39-20577B AA40-00094A AA40-00095A AA59-00171A AA63-10002A AA65-30013A AA65-30018A AA65-30104B AA68-02302A AA68-50509A AA68-00344A AA68-00341A AC68-00347A AA68-00340A AA68-00345A
REMOCON;,TM63,SHARK,51,L/GRAY,EAST ASI ASSY CRT-(R);P16LSG03RJA,+380MG,7,PCL621 ASSY CRT-(G);P16LSG03HKA,+380MG,7,PCL621 ASSY CRT-(B);P16LSG03BMB,+380MG,7,PCL621 TAPE-OPP MASKING;ANT-300P,T0.07,W15.0,L5 TAPE ETC;SESA,T0.3,75,132,BLK SCREW-WOOD;HH,+,M4,L27,BLK,SWRCH18A SCREW-MACHINE;BH,+,M3,L8,ZPC(YEL),SM20C, SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A SCREW-WOOD;HH,+,M4.0,L19,NI PLT,SWRCH18A SCREW-ASS'Y WOOD;WW,HH,+,M7,L32,ZPC(YEL) SPACER-COVER,DUST;DP,W3,T0.5,60-00123B SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, BRACKET-CRT,MAIN;DP,54J7,AA61-00475B PLATE-CENTER,SPK;W3,WOOD ASSY-HOLDER,MIRROR;,HIPS HB BLK,47W3 ASSY-HOLDER,MIRROR;,HIPS HB BLK,47W3 HOLDER-SCREEN,R;47H1,ABS HB,GRAY HOLDER-BOX;-,PP,-,-,-,NTR,V0,AA61-20285A RUBBER-CAP;FLAT,PRJ,SILICONE RUBBER,WHIT BAND-PP;