Text preview for : 3828VD0209R.pdf part of LG 42PX3RVC/RV PLASMA TV



Back to : 3828VD0209R.part1.rar | Home

website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html

PLASMA TV SERVICE MANUAL
CHASSIS : MF-056A

MODEL : 42PX3RVC/RV
42PX3RVC/RV-TA
CAUTION
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

TV/AV

MENU

OK

VOL

PR

CONTENTS

SAFETY PRECAUTIONS ....................................................................................3 DESCRIPTION OF CONTROLS ..........................................................................4 SPECIFICATIONS ................................................................................................8 ADJUSTMENT INSTRUCTIONS .......................................................................11 TROUBLE SHOOTING GUIDE ..........................................................................15 BLOCK DIAGRAM .............................................................................................24 EXPLODED VIEW ..............................................................................................26 EXPLODED VIEW PARTS LIST ........................................................................27 REPLACEMENT PARTS LIST...........................................................................28 SCHEMATIC DIAGRAM......................................................................................... PRINTED CIRCUIT BOARD ..................................................................................

- 2 -

SAFETY PRECAUTIONS
IMPORT ANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this monitor is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts. Due to high vacuum and large surface area of picture tube, extreme care should be used in handling the Picture Tube. Do not lift the Picture tube by it's Neck.

Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

AC Volt-meter

Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

To Instrument's exposed METALLIC PARTS

Good Earth Ground such as WATER PIPE, CONDUIT etc.
0.15uF

1.5 Kohm/10W

- 3 -

DESCRIPTION OF CONTROLS

- When using the remote control aim it at the remote control sensor of the set. - There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.

MUTE Switches the sound on or off. MULTIMEDIA Selects the Component, RGB or DVI modes. switches the set on from standby. TV/AV Selects the TV, AV, Component, RGB or DVI modes. switches the set on from standby. LIST Displays the programme table.
PR

POWER switches the set on from standby or off to standby.
MUTE POWER

TV/AV MULTIMEDIA

I/II

I/II Selects the language during dual language broadcast. Selects the sound output. ARC Changes the picture format. MENU Displays on screen menus one by one. Exits the current menu. Memorizes menu changes.

LIST

ARC

MENU

D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby. F / G (Volume Up/Down) adjusts the volume. adjusts menu settings. OK accepts your selection or displays the current mode.

OK
VOL PR VOL

NUMBER buttons

1 4

2 5 8 0

3 6 9 SSM
SLEEP

SSM To select the sound appropriate to your viewing programme character.

PSM Adjusts the factory preset picture according to the room. SPLIT ZOOM Enlarge the screen with regular ration. PIP/DW Switches the sub picture on or off. Selects PIP or DW modes. PIP PR + /Selects a programme for the sub picture. SWAP Alternates between main and sub picture. PIP INPUT Selects the input mode for the sub picture. WIN.SIZE Adjusts the sub picture size. POSITION Moves the sub picture to D / E or F / G direction.

7 PSM

SPLIT ZOOM PIP/DW REVEAL

SLEEP Sets the sleep timer.

PIP PR+ TEXT/ MIX TIME

?
WIN. SIZE PIP PRPOSITION HOLD SWAP

TEXT/ These buttons are used for teletext. For further details, see the `Teletext' section. Note : In teletext mode, the PIP PR +/-, SWAP and PIP INPUT buttons are used for teletext function.

*

PIP INPUT INDEX

i

SWAP Returns to the previously viewed programme. Note : This function works only when Favourite programme is set to Off. Otherwise each press of this button will select a stored favorite programme.

- 4 -



TV/AV

MENU

OK

VOL

PR

TV/AV

MENU

OK

VOL

PR

1

2

3

4

5

6

7

1. Remote Control Sensor 2. Power Indicator Illuminates red in standby mode, Illuminates green when the set is turned on. 3. Power Button Switches the set on from standby or off to standby. 4. TV/AV Button Selects the TV, AV, Component, RGB or HDMI modes. Switches the set on from standby. 5. MENU Displays on screen menus one by one. Exits the current menu. Memorizes menu changes.

6. OK Accepts your selection or displays the current mode. 7. D / E (Programme Up/Down) Selects a programme or a menu item. Switches the set on from standby. F / G (Volume Up/Down) Adjusts the volume. Adjusts menu settings.

- 5 -



A/V INPUT2
S-VIDEO

VIDEO

9

R AUDIO L/MONO

VIDEO
L

AUDIO
R

VIDEO
L

AUDIO
R
Antenna

AC INPUT

HDMI/ DVI(VIDEO)

AUDIO INPUT

RGB INPUT

COMPONENT INPUT 2

MONITOR OUTPUT MONITOR
AUDIO
L R

REMOTE CONTROL

RS-232C INPUT
(CONTROL/SERVICE)
(MONO)

VARIABLE AUDIO OUT

COMPONENT INPUT 1

A/V INPUT 1

S-VIDEO

1

2

3

4

5

6

7

8

1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUT Connect the monitor output socket of the PERSONAL COMPUTER, DVD or STB to this socket. Note: If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or the EMI Filter core along with separate cable. 2. CONTROL LOCK / REMOTE CONTROL 3. RS-232C INPUT(CONTROL/SERVICE) PORT Connect to the RS-232C port on a PC. 4. COMPONENT INPUT Connect DVD video outputs to Y, PB, PR of COMPONENT INPUT and audio outputs to Audio sockets of AUDIO INPUT. 5. VIDEO/AUDIO IN/OUT SOCKETS (A/V INPUT 1) Connect the video/audio out sockets of external equipment to these sockets. S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEO socket. Connect the audio out sockets of the VCR to the audio sockets as in A/V INPUT 1.

6. VARIABLE AUDIO OUTPUT 7. ANTENNA INPUT 8. POWER CORD SOCKET This the set operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the set on DC power. 9. AUDIO/VIDEO INPUT (A/V INPUT 2) S-VIDEO/AUDIO IN SOCKETS

- 6 -

Accessories
MUTE POWER
TV/AV MULTIMEDIA I/II LIST ARC MENU PR

OK
VOL PR VOL

1 4 7 PSM

2 5 8 0

3 6 9 SSM
SLEEP

SPLIT ZOOM PIP/DW REVEAL

PIP PR+ TEXT/ MIX TIME

?
WIN. SIZE PIP PRPOSITION SWAP

LG TV
AS mark

HOLD

PIP INPUT INDEX

i

Owner's Manual

Remote Control handset

2-Eye Bolts

1.5V 1.5V

Alkaline batteries

Power Cord

2-Wall brackets

Joinning the TV assembly to the wall to protect the set tumbling
- Secure the TV assembly by joinning it to a wall by using the Eye Bolts/Wall brackets.

After the set must be mounted on a desktop, install the Eye Bolts on the set as shown. Insert the 2 Eye Bolts and tighten securely, in the holes on the bracket. Install the wall brackets on the wall with 2 bolts, (not supplied with the product), as shown. Match the height of the Eye Bolts and the wall brackets. Check to be sure the brackets are tightened securely.

Secure the TV assembly to the wall with strong strings or wound wire cables, (not supplied with the product), as shown.

Optional Extras
Optional extras can be changed or modified for quality improvement without any notification new optional extras can be added. Contract your dealer for buying these items.

Tilt wall mounting bracket

Ceiling mounting bracket

40

42
40

42

50

Video cables

Audio cables

- 7 -

SPECIFICATIONS
NOTE : Specifications and others are subject to change without notice for improvement.
V

Application Range
This spec is applied to the 42"PDP TV used MF-056A Chassis.

V

Specification
Each part is tested as below without special appointment. 1) Temperature : 255C (779F), CST : 405 2) Relative Humidity: 6510% 3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz) * Standard Voltage of each product is marked by models. 4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM. 5) The receiver must be operated for about 20 minutes prior to the adjustment.

V

Test Method
1) Performance : LGE TV test method followed. 2) Demanded other specification Safety: CE, IEC specification EMC : CE, IEC Model Name 42PX3RVC-TA Market Non-EU Remark Safety : IEC60065, EMI : CISPR13

V

General Specification
1. Module Specification No 1 2 3 Item Display Screen Device Aspect Ratio PDP Module Specification 42 inch wide Color Display Module 16:9 PDP42V7xxxx RGB Closed Type, Film Filter 4 Operating Environment 1) Temp : 0~40 deg 2) Humidity : 0~85% 5 Storage Environment 1) Temp : -20~60 deg 2) Humidity : 0~85% 6 Input Voltage 100-240V~, 50/60Hz Maker : SONY/ Sanken LGE SPEC PDP Remark

- 8 -

2. Model Specification No 1 2 3 Market Broadcasting system Available Channel Item Non-EU PAL B/G/I/D/K, NTSC BAND VHF/UHF CATV 4 5 6 7 8 9 Receiving system Video Input (2EA) Video Output (1EA) S-Video Input (2EA) Component Input(2EA) RGB Input(1EA) PAL C1~C69 S1~S47 NTSC 2~83 1~71 Specification Remark

Upper Heterodyne PAL, SECAM, NTSC PAL, SECAM, NTSC PAL, SECAM, NTSC Y/Cb/Cr, Y/Pb/Pr RGB-PC RGB-DTV 4 System : PAL, SECAM, NTSC,PAL60 4 System : PAL, SECAM, NTSC,PAL60 4 System : PAL, SECAM, NTSC,PAL60

10

HDMI Input(1EA)

HDMI-PC HDMI-DTV

11 12 13

Audio Input(5EA) Wired Control Audio variable out

PC Audio, Component(2EA), AV(2EA)

L/R Input

- 9 -

RGB / HDMI mode
Resolution 640x350 720x400 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 31.469 37.927 31.469 35.000 640x480 37.861 37.500 43.269 31.500 848x480 37.799 39.375 31.500 852x480 37.799 39.375 35.156 37.879 800x600 48.077 46.875 53.674 832x624 49.725 48.363 1024x768 56.476 60.023 68.677 54.348 1152x864 1152x870 1280x960 1280x1024 63.995 67.500 68.681 60.023 63.981 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 60.00 70.00 75.00 60.00 70.00 75.00 56.25 60.31 72.18 75.00 85.06 74.55 60.00 70.06 75.02 85.00 60.05 70.01 75.00 75.06 60.02 60.02

RGB / HDMI mode
Resolution 640x350 720x400 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 31.469 37.927 31.469 35.000 640x480 37.861 37.500 43.269 31.500 848x480 37.799 39.375 31.500 852x480 37.799 39.375 35.156 37.879 800x600 48.077 46.875 53.674 832x624 49.725 48.363 1024x768 56.476 60.023 68.677 47.700 1360x768 59.625 68.500 47.700 1366x768 59.625 69.500 54.348 63.995 67.500 77.487 1152x870 1280x768 1280x960 1280x1024 68.681 47.693 60.091 68.504 60.023 63.981 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 60.00 70.00 75.00 60.00 70.00 75.00 56.25 (RGB) 60.31 72.18 75.00 85.06 74.55 60.00 70.06 75.02 85.00 60.00 75.02 85.00 60.00 75.02 85.00 60.05 70.01 75.00 85.00 75.06 60.00 75.00 85.00 60.02 60.02

42PX3RV series
1152x864

50PX3RV series

- 10 -

ADJUSTMENT INSTRUCTIONS
1. Application Object
These instructions apply to the MF-056A Chassis.

3-2. Channel memory Method
1) Select "PDP" and "Hurricane" on Model dialog. And check your connection in Communication dialog. (If your connection is `NG', then set your PORT(COM1,2,3,...) correctly.) 2) Connect RS-232C cable and turn on the power. (If your connection has completed, you can see "Ready".) [ If your set is not an end products but only a board, you have to make your board to Stand-by state (LED_R). And you have to Download in Stand_by power state.

2. Specification
(1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of 255C of temperature and 6510% of relative humidity if there is no specific designation. (4) The input voltage of the receiver must keep 100-220V, 50/60Hz. (5) The receiver must be operated for about 15 minutes prior to the adjustment. After RGB Full white HEAT-RUN Mode, the receiver must be operated prior to adjustment. O Enter into HEAT-RUN MODE 1) Press the POWER ON KEY on R/C for adjustment. 2) OSD display and screen display 100% full WHITE PATTERN.
O

[ Set is activated HEAT-RUN without signal generator in this mode. [ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.

(Fig. 3)

Caution) If you turn on a still screen more than 20 minutes (Especially digital pattern, cross hatch pattern), after image may be occur in the black level part of the screen.

3. Channel memory
3-1. Setting up the LGIDS
1) Install the LGIDS. (idsinst.exe) 2) After installation, restart your PC. 3) Extract [files.zip] to folder [c:\LGIDS\files]. 4) Start LGIDS.

3) Select proper CH_memory file(*.nvm) for each model at [NVRAM Download] $ [Write Batch] Next, select proper binary file(*.bin) including the CH information for each model at [NVRAM File]. 4) Click the [Download] button. It means the completion of the CH memory download if all items show `OK' and Status is changed by `PASS' at the lower right corner of the window. 5) If you want to check whether the CH information is memorized correctly or not, click the [Verify] button. And then compare NVRAM File(*.bin) with the CH information downloaded.

(Fig. 3-1)

3-3 Sub program download
1) Select "PDP" and "Hurricane" on Model dialog. And check your connection in Communication dialog. (If your connection is `NG', then set your PORT(COM1,2,3,...) correctly.)

(Fig. 1)

- 11 -

2) Connect RS-232C cable and turn on the power. (Use the special Cable For Sub-program) (If your connection has completed, you can see "Ready")

5. EDID (The Extended Display Identification Data)/ DDC (Display Data Channel) download
5-1. Required Test Equipment
1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID TESTER Ver.2.5) 2) A Jig for EDID Download 3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub 15Pin cable, DVI to HDMI cable

5-2. Setting of device

Each PCB assembly must be checked by check JIG set. (Because power PCB Assembly damages to PDP Module, especially be careful)

(Fig. 5) Connection Diagram of DDC download

5.3. Preparation for Adjustment
1) As above Fig. 5, Connect the Set, EDID Download Jig, PC & Cable. 2) Turn on the PC & EDID Download Jig. And Execute the S/W : EDID TESTER Ver,2.5 3) Set up S/W option Repeat Number : 5 Device Address : A0 PageByte : 8 4) Power on the Set

4. POWER PCB Assy Voltage Adjustments (Va, Vs Voltage Adjustments)
4-1. Test Equipment : D.M.M. 1EA 4-2. Adjustment Method
(1) Va Adjustment
1) After receiving 100% Full White Pattern, HEAT RUN. 2) Connect + terminal of D.M.M to Va pin of P807, connect - terminal to GND pin of P807. 3) After turning RV501, voltage of D.M.M adjustment as same as Va voltage which on label of panel right/top. (Deviation; 0.5V)

(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P807, connect terminal to GND pin of P805. 2) After turning RV401, voltage of D.M.M adjustment as same as Va voltage which on label of panel right/top. (Deviation; 0.5V)

5.4. Sequence of Adjustment
(1) DDC data of Analog-RGB
1) Init the data

2) Load the EDID data.(Open File) [Analog-RGB : MF056A_RGB.ANA] [digital(HDMI) : MF056A_DMI.DVI] (Fig. 4) Connection diagram of power adjustment for measuring 3) Set the S/W as below. 4) Push the "Write Data & Verify"button. And confirm "Yes". 5) If the writing is finished, you will see the "OK" message.

- 12 -

6. Auto AV(CVBS) Color Balance
6-1. Required
- This AV color balance adjustment should be performed befor white Balance Adjustment

W

Auto adjustment Map(RS-232C) Type Baud Rate 115200 MF-056A : RT-42PX40/ RZ-42PX40 Data bit 8 Stop bit 1 Parity NONE

6-2. Required Equipment
1) Remote controller for adjustment 2) AV Pattern Generator : 802F Pattern Generator, Master(MSPG-925FA), etc (Which has PAL Composite Video format output with standard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig6)

Index Cmd1 Cmd2 R Gain G Gain Protocol B Gain Setting R Offset G Offset B Offset j j j j j j a b c d e f

Data Min Value Max Value 00(00) 00(00) 00(00) 00(00) 00(00) 00(00) 255(FF) 255(FF) 255(FF) 255(FF) 255(FF) 255(FF)

6-3. Method of Auto Color Balance
1) Input the PAL Composite Video (Fig6. 100% Color Bar Pattern) into video input. (42PX4RV-TA : AV1/AV2 Input 50Hz, 42PX4RV-ZA : AV4/AV5 Input) 2) Set the PSM to Standard mode in Picture menu. 3) Press INSTAR key on R/C for adjustment. 4) Press the G(Vol. +) key operate to set, then it becomes automatically. 5) Auto-RGB OK means completed adjustment.

7-3. Adjustment of White Balance
O

Operate the zero-calibration of the CA-100, then stick sensor to PDP module surface when you adjust. O For manual adjustment, it is also possible by the following sequence. 1) Select white pattern of heat-run mode by pressing power on key on remote control for adjustment then operate heat run more than 15 minutes. 2) As below Fig.7-1, Supply 216Level (85 IRE) full screen pattern to Video input. (42PX4RV-TA : AV1/AV2 INPUT 50Hz, 42PX4RV-ZA : AV4/AV5 INPUT) 3) Press the TV/AV KEY on R/C for converting input mode. 4) Set the PSM to Standard mode in Picture menu. 5) Enter the White Balance adjustment mode by pressing the INSTART key twice(White Balance) on R/C. 6) Stick sensor to center of the screen and select each items (Red/Green/Blue Gain and offset) using D / E(CH +/-) key on R/C. 7) Adjust Only High Light with R Gain/ B Gain using F / G (VOL+/-) key on R/C. 8) Adjust it until color coordination becomes as below. (High Light G Gain : 7A // Low Light R Offset : 7F, G Offset 7E, B Offset 80 is Fixed) [MF-056A : 42PX4RV-TA/ZA] - VGA 42" Bright : High Light : 80 20cd Color-Coordinate : High Light : X : 0.285 0.003 Y : 0.295 0.003 Color Temperature : 9,300K 500K
216 Level (85 IRE)

(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern

7. Adjustment of White Balance
7-1. Required Equipment
1) Remote controller for adjustment 2) Color Analyzer (CA-100 or same product) 3) Auto W/B adjustment instrument(only for auto adjustment) 4) AV Pattern Generator

7-2. Connecting diagram of equipment for measuring (For Auto Adjustment)
216 Level (85 IRE)

COLOR ANALYZER TYPE ; CA-100

CVBS signal input
M SPG-2 1 0 0 / M STG- 5 2 0 0

(Fig. 7-1) Pattern for Adjustment of White Balance
RS-232C Serial Communication

(Fig. 7) Connection Diagram of Auto W/B adjustment

9) When adjustment is completed, Exit adjustment mode using EXIT key on R/C

- 13 -

8. Auto Component Color Balance
8-1. Required Test Equipment
1) Remote controller for adjustment 2) 802F Pattern Generator (Which has 720p Ypbpr output & PC 1024x768 60Hz with Standard(0.7Vpp) Vertical 100% Color Bar Pattern as Fig.8)

9. Default Value in Adjustment mode
9-1. Auto Color Balance (Component/RGB)
Auto Color Balance(Hex) Auto-RGB Red Offset1 Green Offset1 Blue Offset1 Red Offset2 Green Offset2 Blue Offset2 Red Gain Green Gain Blue Gain Reset
G

8-2. Method of Auto Component Color Balance
1) Input the Component 720p 100% Color Bar signal into Component1 or Component2. 2) Set the PSM to Standard mode in Picture menu. 3) Press INSTART key on R/C for adjustment. 4) Press the G(Vol. +) key operate To set, then it becomes automatically. 5) Auto-RGB OK means complete adjustment

G

To Set 22 24 23 45 43 37 14 31 11 To Set

(Fig. 10) Default Value on OSD

9-2. White Balance
(Fig. 8) Auto Component Color Balance Test Pattern

White Balance(Hex) Red Gain Red Offset Green Gain Green Offset Blue Gain Blue Offset Reset 82 7A 86 7F 7E 80 To Set

9. Auto RGB Color Balance
9-1. Required Test Equipment
1) Remote controller for adjustment 2) 802F Pattern Generator, Master (MSPG-925FA), etc. (Which has XGA 60Hz PC Format output with standard (0.7Vpp) horizontal black and white pattern as Fig.10)

G

(Fig. 10-1) Default Value on OSD

9-2. Method of Auto RGB Color Balance
1) Input the PC 1024x768 60Hz horizontal black and white pattern into RGB. 2) Set the PSM to Standard mode in Picture menu. 3) Press ADJ key on R/C for adjustment. 4) Press the G(Vol. +) key operate To set, then it becomes automatically. 5) Auto-RGB OK means completed adjustment.
Level : 0

Level : 255

(Fig. 9) Auto RGB Color Balance Test Pattern

- 14 -

TROUBLE SHOOTING GUIDE
1. Power Board
1-1. The whole flowchart which it follows in voltage output state

Start check

Doesn't the screen whole come out?

Yes

Is it identical with Power Off condition? Yes

No

Is the Interface signal operated?

Yes 2. Check the Interface signal condition.

No

1. Check the Power Off condition.

Doesn't the low pressure output come out?

Yes

Doesn't the St-by 5V signal come out? Yes

No

Doesn't the 5V Monitor signal come out? Yes 4. Check the 5V Monitor signal circuit.

No

Doesn't the VSC signal RL-ON come out? Yes 5. Check the VSC RL-ON signal. No

No

3. Check the St-by 5V signal circuit.

Doesn't the high tension output come out?

Yes

Doesn't the VSC signal Vs-ON come out? Yes

No

Doesn't the Vs, Va voltage output come out? Yes 8. Check the Vs, Va voltage output circuit.

Doesn't the VSC low pressure output come out? Yes 6. Check the VSC low pressure output

No

7. Check the VSC Vs-ON signal

Does high tension output voltage Drop occur? No

Yes

When the Y, Z B/D Module input connector is remove, does Power Board hightension output voltage Drop occur? Yes 9. Check the Power Board Output high tension circuit

No

When the Y B/D Module input connector is removed, does output voltage drop occur? Yes 10. Check the Z B/D Module output circuit

No

When the Z B/D Module input connector is removed, does output voltage Drop occurs? Yes 11. Check the Y B/D Module output circuit

Manufacture enterprise meaning of a passage

- 15 -

1-2. Sony Power Board Structure

T502: Vs Trans T702: Va Trans T101: St-by Trans
1 2 3

T103: Low Voltage Trans

- 16 -

1-3. Sanken, LG INNOTEK Power Board Structure

T221: Vs Trans T271: Va Trans T121: St-by Trans
1 2 3

T201: Low Voltage Trans

- 17 -

2. No Power
(1) Symptom


Does't minute discharge at module. Non does not come in into the front LED.

(2) Check following
No Is plug in power cord? Yes No Connect the Cable. Plug in power cord.

Is the Line Filter and Power Board Cable connected? Yes

Is the Fuse(F101) on Power Board normal? Yes

No Replace the Fuse.

Is the Power Board and 7P of VSC Board Cable connected? Yes

No Connect the Cable.

After the cable connect is remved to Power Board(except the CN101 connection cable), the AC voltage marking is authorized on manual. When ST-BY 5V is not operated, replace Power Board.

- 18 -

3. Protect Mode
(1) Symptom
After once shining, it does not discharge minutely from module The Rely falls(The sound is audible "click") It is converted with the color where the front LED is red from green.


(2) Check following
Is the Power Board normal ? Yes Is the each connector normal? Yes Is the Y-Board normal? Yes Is the Z-Board normal? Yes Is the X- Board normal? Yes Is the Ctrl Board normal? Yes Is the VSC Board normal? Yes Is the COF of X, Y, Z normal ? No After crisis COF of each board, check the normality operates. If in case normality operates, correspondence COF Fail is replace the module. No Is the output voltage normal after remove P1001, P1100? Yes After remove P1001, 1100 normal operation: Replace VSC Board No Is the output voltage normal after remove P1, 2, 4, 9, 10 connector of Ctrl-B/D? Yes Replace X-Board. No Is the output voltage normal after remove P1, 2, 3, 4, 5 connector of X-B/D? Yes After remove P1, P2, P3 output voltage normality: Replace Right X-B/D After remove P4, P5 output voltage normality: Replace Left X-B/D No Is the Fuse (FS1, FS2) on Z-B/D normal? (In case of open is replace) Yes Is the output voltage normal after remove P1 connector of ZB/D? Yes Replace Z-Board. No Is the Fuse(FS2) on Y-B/D normal? (In case of open is replace) Yes Is the output voltage normal after remove P5, P6 connector of Y-B/D? Yes Replace Y-Board. No After connecting well each connector, the normality it operates? No Replace the connector. No Is output the normality Low/High voltage except Stand-by 5V? No Replace Power Board.

- 19 -

4. No Raster
(1) Symptom


Does't minute discharge at module. It maintains the condition where the front LED is green.

(2) Check following
Is the Power Board normal? Yes Is the each connector normal? Yes Is the Y-Board normal? Yes Is the Z- Board normal? Yes Is the X- Board normal? Yes Is the Ctrl Board normal? Yes Is the VSC Board normal? Yes Is the COF of X, Y, Z normal? No After crisis COF of each board, check the normality operates. If in case normality operates, correspondence COF Fail is replace the module. No Is the output voltage normal after remove P1001, P1100? Yes After remove P1001, P1100 normal operation: Replace the VSC Board No Is the output voltage normal after remove P1, 2, 4, 9, 10 connector of Ctrl-B/D? Yes Replace X-Board. No Is the output voltage normal after remove P1, 2, 3, 4, 5 connector of X-B/D? Yes After remove P1, P2, P3 output voltage normality: Replace Right X-B/D After remove P4, P5 output voltage normality: Replace the Left X-B/D No Is the Fuse(FS1, FS2) normal on Z-B/D? (In case of open is replace) Yes Is normal the output voltage after remove P1 connector of Z-B/D? Yes Replace Z-Board. No Is the Fuse(FS2) normal on Y-B/D? (In case of open is replace) Yes Is the output voltage normal after remove P5, P6 connector of Y-B/D? Yes Replace Y-Board. No After connecting well each connector, the normality it operates? No Replace the connector. No Is output the normality Low/High voltage except Stand-by 5V? No Replace the Power Board.

- 20 -

5. In case of occurring strange screen into specific mode
5-1. In case the OSD does not displayed
(1) Symptom


LED is green The minute discharged continuously becomes accomplished from module

(2) Check following
Is the LVDS cable normal ? No Is the LVDS cable connected well? No Yes Replace the cable.

Yes

Cable inserts well.

Is the VSC Board normal?

No

Does the FIL8532 IC (IC800) Operates ? No

Yes Replace VSC B/D

Yes

Replace FIL8532 IC(IC800).

Is the Ctrl Board of Module normal?

No Replace Ctrl B/D.

- 21 -

5-2. In case of does't display the screen into specific mode
(1) Symptom


The screen does not become the display from specific input mode (RF, AV, Component, RGB, DVI).

(2) Check following


Check the all input mode should become normality display. Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become normality display from the PIP mode or DW mode. (Re-Check it Swap)

(3) In case of becomes unusual display from RF mode
No Is the Tuner normal? Is the Tuner Cable connected well? No Yes Cable inserts well. No Is the Input voltage, IIC Communication and HV sync normal? No Replace the IC Yes Is the Input voltage, IIC Communication and CVBS output normal? No Replace the Tuner

Is the CXA2069Q normal? Yes Is the FIL8532 normal?

No

Is normal the Input voltage, IIC Communication and HV sync?

No Replace the IC

(4) In the case of becomes unusual display from RF, AV mode
Is the CXA2069Q normal? Yes Is the FIL8532 normal? No Is the Input voltage, IIC Communication and HV sync normal? No Replace the IC No Is the Input voltage, IIC Communication and HV sync normal? No Replace the IC

(5) In the case of becomes unusual display from Component, RGB mode
Is the FIL8532 normal? No Is the Input voltage, IIC Communication and HV sync normal? No Replace the IC

(6) In the case of becomes unusual display from HDMI mode
Is the Sil9011 normal? Yes Is the FIL8532 normal? No Is the Input voltage, IIC Communication and HV sync normal? No Replace the IC No Is the Input voltage, IIC Communication and HV sync normal? No Replace the IC

- 22 -

6. In case of no sound
(1) Symptom


LED is green Screen display but sound is not output

(2) Check following
Is the SPK cable normal? No Is the SPK cable connected well? No Yes Cable inserts well. Yes Replace SPK cable

Is the RF/ AV/ Component/ RGB/ HDMI sound normal?

No

Does IC400 Operates ? No Replace IC400

Yes

Does IC401 Operates ? No Replace IC401

Yes

Does IC402 Operates ? No Replace IC402

Replace VSC B/D

- 23 -

BLOCK DIAGRAM

cable

- 24 -

MEMO

- 25 -

EXPLODED VIEW

300 121

600

601 301

304 120

303 302 200

207 202 206

205 520 201 501 203 530 410 401 204 580 400

430

- 26 -

EXPLODED VIEW PARTS LIST
No.
120 121 200 201 202 203 204 205 206 207 300

Part No.
6401VD0032A 6401VD0033A 6348Q-E080N 6871QCH053A 6871QDH084A 6871QDH085A 6871QLH047A 6871QRH055A 6871QYH036A 6871QZH041A 3091V00816B 3091V00816E

Descriptions
SPEAKER ASSEMBLY, FULL RANGE(R) RZ-42PX30 FILM TYPE SPEAKER ASSEMBLY, FULL RANGE(L) RZ-42PX30 FILM TYPE PDP, 42" 852*480 PDP42V70102.AKLGG PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42V7 FPGA PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V7 YDRV TOP B/D PWB(PCB) ASSEMBLY,DISPLA YDRV ASSY HAND INSERT 42V7 YDRV BTM B/D PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42V7 XL B/D PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42V7 XR B/D PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42V7 PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42V7 CABINET ASSEMBLY, RZ-42PX31 STEREO MF056C FILM TYPE CABINET ASSEMBLY, 42PX3RVC STEREO MF056C FILM TYPE 1 TONE SILVER SUPPORTER, ASSY AL FILTER TOP RZ-42PX30 SUPPORTER, ASSY AL FILTER BOTTOM RZ-42PX30 SUPPORTER, ASSY AL FILTER RIGHT RZ-42PX30 SUPPORTER, ASSY AL FILTER LEFT RZ-42PX30 BACK COVER ASSEMBLY, 42PX17/30 NON CHASSIS CHANGE BACK COVER ASSEMBLY, CHASSIS CHANGE WARNING LABEL LGEAP PLATE ASSEMBLY, ASSY 3300V00552B RT-42PX17 PLATE TUNER COVER SUPPORTER, ASSY AL MODULE VER. RZ-42PX10 BOARD ASSEMBLY, ASSY AP-42DX30 MF056C NON PLATE ASSEMBLY, ASSY 3300V00550A 3301V00084A 42PX17/30 PLATE TUNER PWB(PCB) ASSEMBLY,MAIN MF-056A H2, 42PX4RV-TA/42PX3RV-TA PWB(PCB) ASSEMBLY,MAIN MF-056A H2, 42PX3RV-TA FOR AUSTRALIA PWB(PCB) ASSEMBLY,SUB CONT MF056C RZ-42PX30 POWER SUPPLY ASSEMBLY, 350W YPSU-J006A LG INNOTEK PSU ASSY PWB(PCB) ASSEMBLY,SUB A/V MF056A RT/RZ-42PX40 SIDE A/V SUSAB BRACKET ASSEMBLY, DECO RU-42PX10 RF043A SIDE AV

301 302 303 304 400

4980V01203A 4980V01204A 4980V01205A 4980V01206A 3809V00605A 3809V00605E

401 410 430 501 520

3301V00085B 4980V01071A 3501V00216C 3301V00083A 6871VMMF21A 6871VMMF60A

530 580 600 601

6871VSMS36A 6709V00010A 6871VSMS18B 4811V00118B

- 27 -

REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION LOCA. NO Q301 Q302 Q303 Q304 Q400 Q401 Q402 Q403 Q404 Q407 Q409 Q410 Q411 IC1202 IC1203 IC200 IC201 IC503 IC504 IC505 IC506 Q102 Q200 Q203 Q204 Q207 Q305 Q405 Q406 Q408 PART NO 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR830009BA 0TR830009BA 0TR830009BA 0TR830009BA 0TR830009BA 0TR830009BA 0TR830009BA 0TR830009BA 0TR102008AA 0TR150400BA 0TR150400BA 0TR150400BA 0TR150400BA 0TR150400BA 0TR102008AA 0TR102008AA 0TR102008AA DESCRIPTION CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC BSS83 TP PHILIPS N-CHANNEL S/W TR BSS83 TP PHILIPS N-CHANNEL S/W TR BSS83 TP PHILIPS N-CHANNEL S/W TR BSS83 TP PHILIPS N-CHANNEL S/W TR BSS83 TP PHILIPS N-CHANNEL S/W TR BSS83 TP PHILIPS N-CHANNEL S/W TR BSS83 TP PHILIPS N-CHANNEL S/W TR BSS83 TP PHILIPS N-CHANNEL S/W TR KRA102S R/TP KEC SOT23 CHIP TR CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC KRA102S R/TP KEC SOT23 CHIP TR KRA102S R/TP KEC SOT23 CHIP TR KRA102S R/TP KEC SOT23 CHIP TR

IC
IC401 IC1201 IC1302 IC500 IC701 IC703 IC802 IC900 IC901 IC902 IC300 IC400 IC402 IC700 IC800 IC1200 IC600 IC1000 IC1001 IC1002 IC1003 IC1004 IC1005 IC1100 IC1101 IC1102 IC1103 IC1104 IC1105 IC1106 IC202 IC403 IC301 IC404 IC502 0ILNR00015A 0IMMRAL014B 0IMP242560A 0IMMRAL014B 0IMMRAL025A 0IMMR00004A 0IMP242560A 0IMMRAL016D 0IMMR00002A 0IMMR00002A 0ISO206900A 0IMCRMN028B 0IMCRTI028C 0IMCR02006A 0IMCR02005A 0IPRPS5005A 0IPRP00009A 0IPRPML001A 0IMCRRH001A 0IMCRFA010A 0IPMG00027A 0IMCRRH001A 0IMCRRH001A 0IMCRRH001A 0IPRPML001A 0IPMG00027A 0IPMGKE030A 0IPMG00027A 0IPRPML001A 0IMCRRH001A 0IPMGON013B 0ISS455880A 0ISA721700C 0IPH741400E 0IPH741400E NSP-2100A,LF NEOFIDELITY TQFP 64P R/TP AT24C02N-10SI-2.7 ATMEL 8P SOIC 24LC256-I/SM 8P,SOP TP 256K IIC SERIAL AT24C02N-10SI-2.7 ATMEL 8P SOIC R/TP AT24C32AN-10SI-2.7 ATMEL 8PIN SOP SST25VF040-20-4C-S2AE-T SST SOIC 8P 24LC256-I/SM 8P,SOP TP 256K IIC AT49BV160-70TI ATMEL 48P TSOP K4D261638F-LC50,LF TSOPII 66P K4D261638F-LC50,LF TSOPII 66P CXA2069Q QFP64 BK I2C BUS AV S/W MSP4410K MICRONAS 80P/PQFP TAS5122DCAR 56P/TSSOP R/TP 30W FLI8125BB-LF GENESIS 208P/PQFP FLI8532BD-LF GENESIS 416P/PBGA SII9011CLU(PB FREE) SILICON IMAGE 128P ICL3232CBNZ INTERSIL 16P/SOP R/TP MIC39100 MICREL 3P SOT223 R/TP BA033FP-E2 ROHM 3P-SOP,TO252-3 KA7809R, FAIRCHILD 2P D-PAK, R/TP SC156515M-1.8TR 5P/TO-263-5 BA033FP-E2 ROHM 3P-SOP,TO252-3 BA033FP-E2 ROHM 3P-SOP,TO252-3 BA033FP-E2 ROHM 3P-SOP,TO252-3 MIC39100 MICREL 3P SOT223 R/TP SC156515M-1.8TR 5P/TO-263-5 KIA78R05F KEC 5PIN DPAK R/TP 1A,5V SC156515M-1.8TR 5P/TO-263-5 MIC39100 MICREL 3P SOT223 BA033FP-E2 ROHM 3P-SOP,TO252-3 MC34063ADR2G ON SEMI SO-8P KA4558D 8SOP OP AMP LA7217M MFP14 TP SYNC SEPARATOR 74HC14D 14SOP TP SHITTER TRIGGER 74HC14D 14SOP TP SHITTER TRIGGER

DIODE
D1012 D1013 D503 D504 D505 D506 ZD300 0DD200009AF 0DD200009AF 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA RU2M V(1) TP SANKEN RU2M V(1) TP SANKEN SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC

TRANSISTOR
Q100 Q1000 Q1001 Q1002 Q1003 Q1004 Q101 Q101 Q102 Q1200 Q201 Q202 Q205 Q300 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC

ZD301 ZD600 D1005 D1006 D1007 D1008 D1009 D1010 D106 D107 D108 D109 D1100 D1104

- 28 -

For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;

CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic

RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible

LOCA. NO D1105 D1106 D1107 D1109 D1110 D1200 D1201 D200 D300 D500 D501 D502 ZD400

PART NO 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD184009AA 0DS113379BA 0DD184009AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DZRM00248A KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC

DESCRIPTION

LOCA. NO C1085 C1087 C1098 C1099 C1102 C1105 C1107 C1108 C1110 C1115 C1116 C1117 C1118 C1119 C1120 C1126 C113 C1135 C1136 C1137 C1138 C114 C1148 C1149 C115 C1150 C1151 C1154 C1159 C1162 C1165 C1166 C1185 C1186 C1187 C1188 C1189 C1190 C1191 C1192 C1193 C1195 C1199 C1200 C1201 C1225 C1245 C1247 C1302 C1304 C1306 C1309

PART NO 0CE476SF6DC 0CE477SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE477SF6DC 0CE477DJ618 0CE477SF6DC 0CE227VF6DC 0CE477SF6DC 0CE477DJ618 0CE227VF6DC 0CE477SF6DC 0CE106SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE106SF6DC 0CE476SF6DC 0CE107SF6DC 0CE227SF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE476SF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE107SF6DC

DESCRIPTION 47UF MVG 16V 20% SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 470UF STD 35V 20% FL TP 5 470UF MVG 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 470UF STD 35V 20% FL TP 5 220UF MV 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 220UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP

KDS184 TP KEC - 85V 300MA 1SS133 T-72 TP ROHM KOREA DO34 90V KDS184 TP KEC - 85V 300MA KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC KDS226 TP KEC RLZ8.2B-TE11 ROHM R/TP LLDS(LL-34)

CAPACITOR
C103 C1230 C1231 C1411 C315 C318 C319 C320 C321 C325 C451 C456 C1000 C1005 C1007 C1009 C1010 C1019 C1022 C1030 C1043 C1046 C1047 C1050 C1051 C1064 C1065 C1066 C1067 C1068 C1069 C1071 C1073 C108 C1082 C1083 C1084 0CE4763F618 0CK105DF64A 0CK105DF64A 0CK105DF64A 0CK225DFK4A 0CK225DFK4A 0CK225DFK4A 0CK225DFK4A 0CK225DFK4A 0CK225DFK4A 0CK105DF64A 0CK105DF64A 0CE477SF6DC 0CE477SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE477SF6DC 0CE476SF6DC 0CE477SF6DC 0CE477SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE477SF6DC 0CE477SF6DC 0CE227SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 47UF SRE 16V M FL TP5 1UF 2012 16V 20% R/TP F(Y5V) 1UF 2012 16V 20% R/TP F(Y5V) 1UF 2012 16V 20% R/TP F(Y5V) 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP 1UF 2012 16V 20% R/TP F(Y5V) 1UF 2012 16V 20% R/TP F(Y5V) 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V 20% SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 220UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP

- 29 -

For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;

CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic

RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible

LOCA. NO C1311 C1312 C1313 C1314 C1315 C1316 C1317 C1318 C1405 C1406 C1410 C1414 C1417 C1417 C1418 C1418 C1423 C1424 C1427 C1428 C1431 C1432 C1436 C1437 C1506 C203 C204 C208 C210 C211 C214 C215 C221 C238 C241 C300 C304 C305 C307 C327 C329 C337 C402 C403 C413 C418 C422 C425 C437 C444 C457 C462

PART NO 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE475SK6DC 0CE476SK6D8 0CE475SK6DC 0CE476SK6D8 0CE106SH6DC 0CE106SH6DC 0CE227VF6DC 0CE227VF6DC 0CE106SH6DC 0CE106SH6DC 0CE227VF6DC 0CE227VF6DC 0CE476SF6DC 0CE475SK6DC 0CE477SF6DC 0CE477SF6DC 0CE475SK6DC 0CE477SF6DC 0CE106SF6DC 0CE475SK6DC 0CE477SF6DC 0CE107SF6DC 0CE476SK6D8 0CE107SF6DC 0CE226SF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE105SK6DC 0CE105SK6DC 0CE476SF6DC 0CE226SF6DC 0CE335VK6DC 0CE107SF6DC 0CE106SF6DC 0CE226SF6DC 0CE106SF6DC 0CE107SF6DC 0CE335VK6DC 0CE107SF6DC

DESCRIPTION 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 4.7UF MVG 50V 20% SMD R/TP 47UF MVG,MC 50V 20% SMD TAPPING 4.7UF MVG 50V 20% SMD R/TP 47UF MVG,MC 50V 20% SMD TAPPING 10UF MVG 25V 20% SMD R/TP 10UF MVG 25V 20% SMD R/TP 220UF MV 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 10UF MVG 25V 20% SMD R/TP 10UF MVG 25V 20% SMD R/TP 220UF MV 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 47UF MVG 16V 20% SMD R/TP 4.7UF MVG 50V 20% SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 4.7UF MVG 50V 20% SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 4.7UF MVG 50V 20% SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V 20% SMD R/TP 47UF MVG,MC 50V 20% SMD TAPPING 100UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 1UF MVG 50V 20% SMD R/TP 1UF MVG 50V 20% SMD R/TP 47UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 3.3UF MV 50V 20% R/TP(SMD) SMD 100UF MVG 16V 20% SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 22UF MVG 16V 20% SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V 20% SMD R/TP 3.3UF MV 50V 20% R/TP(SMD) SMD 100UF MVG 16V 20% SMD R/TP

LOCA. NO C463 C464 C465 C480 C481 C482 C495 C527 C610 C728 C729 C730 C731 C735 C737 C739 C745 C750 C752 C760 C762 C764 C767 C771 C832 C833 C834 C835 C836 C837 C838 C839 C840 C851 C853 C884 C896 C901 C904 C905 C930 C943 C950 C483 C484

PART NO 0CE106SF6DC 0CE106SF6DC 0CE106SK6DC 0CE108DJ618 0CE475SK6DC 0CE475SK6DC 0CE108DJ618 0CE476SF6DC 0CE107SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CF4741L438 0CF4741L438

DESCRIPTION 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 50V 20% SMD R/TP 1000UF STD 35V 20% FL TP 5 4.7UF MVG 50V 20% SMD R/TP 4.7UF MVG 50V 20% SMD R/TP 1000UF STD 35V 20% FL TP 5 47UF MVG 16V 20% SMD R/TP 100UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 0.47UF D 63V 5% TP 5 M/PE NI 0.47UF D 63V 5% TP 5 M/PE NI

COIL
L1000 L1101 L1102 L1103 L1104 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4

- 30 -

For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;

CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic

RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible

LOCA. NO L404 L405 L406 L407

PART NO 6140VB0032A 6140VB0032A 6140VB0032A 6140VB0032A

DESCRIPTION DBF-1015A 15.5UH 10PIE DIGITAL AUDIO DBF-1015A 15.5UH 10PIE DIGITAL AUDIO DBF-1015A 15.5UH 10PIE DIGITAL AUDIO DBF-1015A 15.5UH 10PIE DIGITAL AUDIO

LOCA. NO AR817 R230

PART NO 0RRZVTA001B 0RD0331H609

DESCRIPTION MNR14-E0A-J-510 R OHM 51 OHM 5% 3.3 OHM 1/2 W 5.00% TA52

LED
D1003 D1101 D1102 D1103 D1104 LD101 0DL233309AC 0DL233309AC 0DL233309AC 0DL233309AC 0DL233309AC 0DL200000CA SAM2333 GREEN:10MCD, RED:6MCD SAM2333 GREEN:10MCD, RED:6MCD SAM2333 GREEN:10MCD, RED:6MCD SAM2333 GREEN:10MCD, RED:6MCD SAM2333 GREEN:10MCD, RED:6MCD SAM5670(DL-2LRG) BK Y-GREEN

CONNECTOR
C1 C2 C3 C4 C5 C6 C7 JK500 JK601 387-J12N 6631V00020J 6631V00045B 6631V25083A 6631V39013N 6631V39022D 6631V39023D 6630G70016A 6630G70017A 12P 2.5MM 900MM H-H UL1185AWG26 3P 3.96MM 400MM H-W UL1672 AWG18 10P SPECIAL 150MM H-H UL1007AWG24 7P 2.5MM 100MM H-H UL1007 AWG24 8P 3.96MM 900MM H-H UL1617AWG22 4P 3.96MM 250MM H-H UL1007AWG18 10P 3.96MM 250MM H-H UL1007AWG18 A03-7071-094 SPG 15P 2.29MM A02-0915-101 SPG 9P 2.54MM RS232

SWITCH
SW101 SW102 SW103 SW104 SW105 SW106 SW107 SW108 SW700 SW800 140-315A 140-315A 140-315A 140-315A 140-315A 140-315A 140-315A 140-315A 6600VR1004A 6600VR1004A TACT SKHV17910B LG C&D 12V TACT SKHV17910B LG C&D 12V TACT SKHV17910B LG C&D 12V TACT SKHV17910B LG C&D 12V TACT SKHV17910B LG C&D 12V TACT SKHV17910B LG C&D 12V TACT SKHV17910B LG C&D 12V TACT SKHV17910B LG C&D 12V SKHMPW 5P CHIP TACT J-ALPS .V .A SKHMPW 5P CHIP TACT J-ALPS .V .A

RESISTOR
AR1200 AR1201 AR1202 AR1203 AR1204 AR1205 AR700 AR701 AR702 AR703 AR704 AR705 AR806 AR806 AR807 AR807 AR808 AR808 AR809 AR809 AR810 AR810 AR811 AR811 AR812 AR812 AR813 AR813 AR814 AR814 AR815 AR815 AR816 AR816 AR817 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 0RRZVTA001B 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24

FILTER & CRYSTAL
L100 L1004 L1005 L1006 L1007 L1008 L1009 L101 L1010 L1011 L1012 L1013 L1014 L1015 L1016 L1017 L1018 L1019 L102 L1020 L1021 L1022 L1023 L1024 L1025 L103 L109 L110 6200JB8010L 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200JB8010L 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200JB8010L 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200JB8010L 6200JB8010L 6200JB8010L MLB-201209-1000L-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS

- 31 -

LOCA. NO L1105 L1106 L1107 L1108 L1109 L111 L1110 L1111 L1112 L1113 L1115 L1116 L1117 L1118 L1119 L1120 L1121 L1122 L1123 L1125 L1126 L1127 L1128 L1129 L1130 L1204 L1205 L1206 L1207 L1208 L1209 L200 L201 L202 L203 L204 L300 L301 L302 L400 L401 L402 L403 L408 L409 L414 L415 L416 L417 L500 L502 L503

PART NO 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200JB8010L 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200JB8010L 6200J000013 6200J000013 6200J000013 6200J000013 6200JB8010L 6200JB8010L 6200J000013 6200J000013 6200J000013 6200J000013 6200J000013 6200JB8010L 6200JB8010L

DESCRIPTION MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS MLB-201209-1000L-N2 MAG LAYERS

LOCA. NO L506 L604 L900 X300 X1200 X400 X700 X800

PART NO 6200J000013 6200J000013 6200J000013 166-E02F 6212AB2845A 156-A02M 6212AB2844A 6212AB2844A

DESCRIPTION MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS MLB-321611-0500P-N2 MAG LAYERS RESONATOR,CERAMIC CSBLA500KECZF09-B0 RESONATOR,CRYSTAL ABLS-27.000MHZ RESONATOR,CRYSTAL HC49U 18.432MHZ RESONATOR,CRYSTAL ABLS-19.6608MHZ RESONATOR,CRYSTAL ABLS-19.6608MHZ

JACK
JK101 JK1200 JK502 JK600 JK100 JK101 JK102 JK400 6613V00026A 6612B00015B 6612F00087A 6612F00087A 6612J00040B 6612J10012A 6612J10012A 6612J00037A UJB-03-28A UGCOM 6613V00004S DC1R019WDH JAE 0.5MM,19PIN+2PIN UEJ-CV-032 UGCOM EAR JACK 10MM UEJ-CV-032 UGCOM EAR JACK 10MM UJB-06-23B UGCOM 6P RCA+1P UJB-05-02C GR/BL/RD/WH/RD 1*5 SHIELD UJB-05-02C GR/BL/RD/WH/RD 1*5 SHIELD UJB-02-12A UGCOM 2P RCA VERTICAL+SHIELD

ACCESSORIES
A1 A2 A3 A4 A5 A6 3828VA0545A 6710V00126R 6410VSH001D 4972V00178A 366-017A 486-395C MANUAL,OWNERS MF056A NEU/42PX3RV REMOTE CONTROLLER,RF043A PIP RZ-42PY20 40 POWER CORDAU10S3+V1625 SAA 2800MM FIXERWALL ASSY PDP SET PIN,DRAWINGSUB STAPLE NO.10 D0.3 L1 . CARDLG LGEAP 1YR PDP/PRJT

MISCELLANEOUS
C10 C8 C9 PA101 TU200 TU201 6851V00022C 6850J00005B 6850VA0004J 6712000002B 6700MF0010B 6700MF0010A CABLE,COAXIAL COAXIAL(150MM),UL1365#26 VW-1 CABLE,DVI LVDS UL20276 AWG30 500MM 3C CABLE,COAXIAL UL1365#26 150MM UCA-EX-069 REMOTE CONTROLLER RECEIVER,KSM-603SM12E-1 TUNER TAFM-W502P LFS MINI 4SYSTEM SUB TUNER TAUM-W501P MINI 4 SYSTEM MAIN

- 32 -

PRINTED CIRCUIT BOARD
MAIN (TOP) MAIN (BOTTOM )

SIDE A/V(BOTTOM)

CONTROL

P/NO : 3828VD0209R

Apr., 2005 Printed in Korea