Text preview for : SM_FE700.pdf part of NEC FE700 NEC FE700 Manual



Back to : SM_FE700.part1.rar | Home

PART NO. 599910510




SERVICE MANUAL
COLOR MONITOR MultiSync FE700/FE700M

MODELS FE700(N9705) (A)/(B)
FE700M(N9705) (A)/(B)

FE700 have two kind models.


The maintenance of FE700(models JC-17W01) on the nameplate is
performed by the original service manual( Part No.599910496)


The maintenance of FE700(models N9705) on the nameplate is performed
by this service manual.


FE700M has the AUDIO unit instead of the revolving stand.




NEC-MITSUBISHI electric visual systems Corporation
200002
08109420
08109421
08109422
08109423
WARNING
The SERVICE PERSONNEL should have the appropriate technical training, knowledge and experience
necessary to:
· Be familiar with specialized test equipment, and
· Be careful to follow all safety procedures associated with high voltage CRT circuit designs to minimize
danger to themselves and their coworkers.

To avoid electrical shocks, this equipment should be used with an appropriate power code and be
connected only to a properly grounded AC outlet.

This equipment utilized a micro-gap power switch. Turn off the set by first pushing the front panel
power switch. Next, remove the power cord from the AC outlet.

To prevent fire or shock hazards, do not expose this unit to rain or moisture.
This symbol warns the personnel that un-insulated voltage within the unit may have sufficient
magnitude to cause electric shock.

This symbol alerts the personnel that important literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any problems.
PRODUCT SAFETY CAUTION

1. When parts replacement is required for servicing, always use the manufacturer's specified replacement.

2. Comply with all caution and safety-related notes on the product display chassis and picture tube.

3. When replacing the component, always be certain that all the components are put back in the place.

4. When servicing display monitor unit, it is required that the provided lead dress is used in the high voltage
circuit area.

5. It is also recommended that shatter proof goggles are worn, when removing installing and handling the
picture tube. People not equipped with the proper precautionary measures mentioned should keep the
picture tube away from body while handling.

6. As for a connector, pick and extract housing with fingers properly since a disconnection and improper
contacts may occur, when wires of the connector are led.

7. Use a proper screwdriver. If you use screwdriver that does not fit, you may damage the screws.

8. X-radiation precaution
This product contains critical electrical and mechanical parts essential for X-ray protection.
Normal anode voltage is 27.0 kV at zero beam picture tube current under AC 100-120V/220-240V input,
and anode voltage must not exceed the voltages shown below under any operation condition.
To measure anode voltage set brightness for very dim picture, and use a high impedance volt meter
between chassis and anode lead and measure high voltage.
If high voltage exceeds the specifications on the chassis schematic diagram, take the necessary
corrective action.


Table MAXIMUM ANODE VOLTAGE

beam current at 0 mA at 0.8 mA at 1.4 mA
A/B 34.5 kV 32.5 kV 32.3 kV



9. When you degauss the set with an external degaussing coil, you must keep strictly item " Notes
about degaussing method " of ADJUSTMENT PROCEDURES.
Index
Warning 1
Contents 2
Quick Start 3-4
Controls 5-7
Recommended Use 8-9
Specifications 10
Features 11
Troubleshooting 12
References 13
Limited Warranty 14
TCO'99 15-16
Avertissement 18
Contenu 19
Mise en marche rapide 20-21
Commandes 22-24
Usage recommandé 25-26
Fiche technique 27
Fonctions 28
Dépannage 29
Références 30
Garantie limitée 31
TCO'99 32-33
Warnung 36
Lieferumfang 37
Quick Start 38-39
Bedienungselemente 40-42
Empfehlungen für die Verwendung 43-44
Technische Daten 45
Funktionen 46
Fehlerbehebung 47
Verweise 48
Beschränkte Gewährleistung 49
TCO'99 50-51
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE
THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS
CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.


CAUTION
RISK OF ELECTRIC SHOCK · DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this
unit has been included. Therefore, it should be read carefully in order to avoid any problems.

Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations
according to C.S.A. 22.2 #950.
FCC Information
1. Use the attached specified cables with the N9705 color monitor so as not to interfere
with radio and television reception.
(1) Please use the supplied power cable or equivalent to ensure FCC compliance.
(2) Shielded captive type signal cable.
Use of other cables and adapters may cause interference with radio and television
reception.
2. This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment gener-
ates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
· Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician
for additional suggestions. The user may find the following booklet, prepared by the Federal
Communications Commission, helpful: "How to Identify and Resolve Radio-TV Interference
Problems." This booklet is available from the U.S. Government Printing Office, Washington,
D.C., 20402, Stock No. 004-000-00345-4.




1
Contents
You can register your product online at
www.nectech.com/productregistration
Your new NEC Technologies MultiSync® FE700TM monitor box*
should contain the following:
· MultiSync FE700 Monitor with tilt/swivel base
· Power Cord
· Captive Signal Cable
· User's Manual




Captive Signal Cable




User's Manual Power Cord



* Remember to save your original box and packing material to transport or ship
the monitor.
2
Quick Start
To attach the MultiSync® FE700TM Series monitor to your system,
follow these instructions:
1. Turn off the power to your computer.
2. If necessary, install the display card into your system. For more information,
refer to the display card manual.
3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable to the
connector of the display card in your system (Figure A.1). Tighten all screws.
For the Mac: Connect the MultiSync FE700 Macintosh cable adapter (not
included) to the monitor connector on the Macintosh (Figure B.1). Attach the
15-pin mini D-SUB end of the captive signal cable to the MultiSync FE700
Macintosh cable adapter on the computer (Figure B.1). Tighten all screws.
NOTE: To obtain the MultiSync FE700 Macintosh cable adapter, call
NEC Technologies at (800) 820-1230.
4. For download information on the Windows® 95/98 INF file for your
MultiSync monitor, refer to the References section of this User's Manual.
5. Connect one end of the power cord to the MultiSync FE700 monitor and the
other end to the power outlet (Figure C.1).
6. Turn on the monitor (Figure D.1) and the computer.
NOTE: If you have any problems, please refer to the Troubleshooting section of
this User's Manual.




Figure A.1

3
Quick Start cont.




Figure B.1




Figure C.1




Figure D.1




4
Controls
OSMTM (On-Screen Manager) control buttons on the front of the monitor function
as follows:
Main Menu Sub-Menu
EXIT Exits the OSM menu. Exits to the OSM controls
main menu.
CONTROL Moves the highlighted Moves the highlighted area
/ area up/down to select up/down to select one of the
one of the controls. controls.

CONTROL Moves the highlighted Moves the bar in the ­ or +
­/+ area left/right to select direction to decrease or
one of the controls. increase the adjustment.

PROCEED Has no function. Only executes control
or enters sub, sub-menu.
RESET Resets all the controls within Resets the highlighted control
the highlighted menu to the factory setting.
to the factory setting.
NOTE: When RESET is pressed in the main and sub-menu, a warning
window will appear allowing you to cancel the reset function.


When OSM controls are activated, icons are displayed at the top of the menu.
If an arrow () is displayed in a sub-menu, it indicates further choices are
available. To enter a sub, sub-menu, press PROCEED.
Brightness/Contrast Controls
Brightness: Adjusts the overall image and background screen brightness.
Contrast: Adjusts the image brightness in relation to the background.
Degauss: Eliminates the buildup of stray magnetic fields which alter the correct
scan of the electron beams and affect the purity of the screen colors, focus and
convergence. When activated, your screen image will jump and waver a bit as
the screen is demagnetized.
Caution: Please allow a minimum of 20 minutes to elapse between uses of the
Degauss Control.

Size and Position Controls
Left/Right: Moves the image horizontally (left or right).
Down/Up: Moves the image vertically (up or down).
Narrow/Wide: Decreases or increases the horizontal size of the image.
Short/Tall: Decreases or increases the vertical size of the image.




5
Controls cont.
Color Control/AccuColor® Control System
Color presets 1 through 5 selects the desired color setting. The bar is replaced
by the color setting choice from 1 to 5. Each color setting is adjusted at the
factory to the stated Kelvin. If a setting is adjusted, the name of the setting will
change from Kelvin to Custom.
Red, Green, Blue: NEC's AccuColor Control System decreases or increases the
monitor's red, green or blue color guns depending upon which is selected. The
change in color will appear on screen and the direction (decrease or increase)
will be shown by the bars.

Geometry Controls
Geometry Controls Menu
The Geometry controls allow you to adjust the curvature or angle of the sides of
your display.
Sides In/Out (pincushion): Decreases or increases the curvature of the sides either
inward or outward.
Sides Left/Right (pincushion balance): Decreases or increases the curvature of
the sides either to the left or right.
Sides Tilt (parallelogram): Decreases or increases the tilt of the sides either to the
left or right.
Sides Align (trapezoidal): Decreases or increases the bottom of the screen to be
the same as the top.
Rotate (raster rotation): Rotates the entire display clockwise or counterclockwise.
Tools 1
Moiré Canceler: Moiré is a wavy pattern which can sometimes appear on the screen.
The pattern is repetitive and superimposed as rippled images. When running certain
applications, the wavy pattern is more evident than in others. To reduce moiré, adjust
the level by using ­/+ CONTROL buttons.
Factory Preset: Selecting Factory Preset allows you a reset most OSMTM control
settings back to the factory settings. A warning statement will appear to confirm
that you do want to reset ALL settings. Individual settings can be reset by high-
lighting the control to be reset and pressing the RESET button.
Tools 2
Language: OSM controls menus are available in seven languages.
OSM Turn Off: The OSM controls menu will stay on as long as it is in use. In the
OSM Turn Off sub-menu, you can select how long the monitor waits after the last
touch of a button for the OSM controls menu to disappear. The preset choices
are 10, 20, 30, 60 and 120 seconds.


6
Controls cont.
OSM Lock Out: This control completely locks out access to all OSM controls
functions except Brightness and Contrast. When attempting to activate OSM
controls while in the lock out mode, a screen will appear indicating that OSM
controls are locked out. To activate the OSM Lock Out function, press PROCEED,
then press and hold down simultaneously. To deactivate the OSM Lock Out,
press PROCEED, then press and hold down simultaneously.
IPMTM System Off Mode: Enable: The IPM System works
normally and all stages of
energy savings are utilized.
Disable: The Off Mode of the IPM
System is not used.
NOTE: For standard systems and graphics boards, keep the factory setting
at ENABLE.
Refresh Notifier: A message will advise you if the refresh rate of the signal being
applied to the monitor by the computer is too low. For further information, please
refer to your display card or system manual.
Information
Display Mode: Indicates the current mode and frequency setting of the monitor.
Monitor Info: Indicates the model and serial numbers of your monitor.




7
Recommended Use
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTISYNC® FE700TM COLOR MONITOR:
· DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and
opening or removing covers may expose you to dangerous shock hazards or other
risks. Refer all servicing to qualified service personnel.
· Do not spill any liquids into the cabinet or use your monitor near water.
· Do not insert objects of any kind into the cabinet slots, as they may touch danger-
ous voltage points, which can be harmful or fatal or may cause electric shock, fire
or equipment failure.
· Do not place any heavy objects on the power cord. Damage to the cord may
cause shock or fire.
· Do not place this product on a sloping or unstable cart, stand or table, as the
monitor may fall, causing serious damage to the monitor.
· Keep the monitor away from high capacity transformers, electric motors and other
devices such as external speakers or fans, which may create strong magnetic
fields.
· If possible, position the monitor so that it is facing the east to minimize the effects
of the earth's magnetic field.
· Changing the direction of the monitor while it is powered on may cause image
discoloration. To correct this, turn the monitor off for 20 minutes before powering
it back on.
· When operating the MultiSync FE700 with its AC 220-240V worldwide power
supply, use a power supply cord that matches the power supply voltage of the AC
power outlet being used. The power supply cord you use must have been ap-
proved by and comply with the safety standards of your country. (Type H05VV-F
should be used except in UK)
· In UK, use a BS-approved power cord with molded plug having a black (SA) fuse
installed for use with this monitor. If a power cord is not supplied with this monitor,
please contact your supplier.
Immediately unplug your monitor from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
· When the power supply cord or plug is damaged.
· If liquid has been spilled, or objects have fallen into the monitor.
· If the monitor has been exposed to rain or water.
· If the monitor has been dropped or the cabinet damaged.
· If the monitor does not operate normally by following operating instructions.
· Allow adequate ventilation around the monitor so that heat can properly
dissipate. Do not block ventilated openings or place the monitor near a
radiator or other heat sources. Do not put anything on top of monitor.
· The power cable connector is the primary means of detaching the system
CAUTION from the power supply. The monitor should be installed close to a power
outlet which is easily accessible.
· Handle with care when transporting. Save packaging for transporting.
8
Recommended Use cont.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR
CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE
FOLLOWING WHEN YOU POSITION THE MONITOR:

· Adjust the monitor height so that the top of
the screen is at or slightly below eye level.
Your eyes should look slightly downward
when viewing the middle of the screen.
· Position your monitor no closer than 16 inches
and no further away than 24 inches from your
eyes. The optimal distance is 20 inches.
· Rest your eyes periodically by focusing on
an object at least 20 feet away. Blink often.
· Position the monitor at a 90° angle to
windows and other light sources to minimize
glare and reflections. Adjust the monitor tilt so that ceiling lights do not reflect
on your screen.
· If reflected light makes it hard for you to see your screen, use an anti-glare filter.
· Clean your monitor regularly. Use a lint-free, non-abrasive cloth and a
non-alcohol, neutral, non-abrasive cleaning solution or glass cleaner to
minimize dust.
· Adjust the monitor's brightness and contrast controls to enhance readability.
· Use a document holder placed close to the screen.
· Position whatever you are looking at most of the time (the screen or
reference material) directly in front of you to minimize turning your head
while you are typing.
· Get regular eye checkups.
Ergonomics
To realize the maximum ergonomics benefits, we recommend the following:
· Adjust the Brightness until the background raster disappears
· Do not position the Contrast control to its maximum setting
· Use the preset Size and Position controls with standard signals
· Use the preset Color Setting and Sides Left/Right controls
· Use non-interlaced signals with a vertical refresh rate between 75-120Hz
· Do not use primary color blue on a dark background, as it is difficult to see
and may produce eye fatigue due to insufficient contrast
For more detailed information on setting up a healthy work environment, call NEC
at (800) 820-1230, NEC FastFactsTM information at (630) 467-4363 and request
document #900108 or write the American National Standard for Human Factors
Engineering of Visual Display Terminal Workstations ­ ANSI-HFS Standard
No. 100-1988 ­ The Human Factors Society, Inc. P.O. Box 1369, Santa Monica,
California 90406.
9
Specifications
Monitor MultiSync® FE700TM Notes
Specifications Monitor
Picture Tube Diagonal: 17 inch 90° deflection, 0.25 mm grille pitch,
Viewable Image Size: 16 inch medium short persistence phosphor,
Radius: 50,000 mm aperture grille CRT, multi-layered, anti-static
screen coating, dark-tint screen and
OptiClear® screen.
Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms
Sync: Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative) (TTL Level)
Display Colors Analog input: Unlimited number of Colors Depends on display card used.
Synchronization Horizontal: 31 kHz to 70 kHz Automatically
Range Vertical: 55 Hz to 120 Hz Automatically
Resolutions Supported 640 x 480 @ 60 to 120 Hz Some systems may not support
Resolution based on horizontal and 800 x 600 @ 55 to 110 Hz all modes listed.
vertical frequencies only 832 x 624 @ 55 to 105 Hz
1024 x 768 @ 55 to 87 Hz ....................... NEC cites recommended resolution at
1152 x 870 @ 55 to 77 Hz 85 Hz for optimal display performance.
1280 x 1024 @ 55 to 66 Hz
Active Display Area Horizontal: 315 mm/12.4 inches Dependent upon signal timing used,
(Factory Setting) Vertical: 236 mm/9.3 inches and does not include border area.
Active Display Area 325 mm/12.8 inches Dependent upon signal timing used,
(Full Scan) 243 mm/9.6 inches and does not include border area.
Power Supply AC 100 ­ 240 V, 50/60 Hz
Current Rating 1.8A @ 100-240 V
Dimensions 403 mm (W) x 427 mm (H) x 424 mm (D)
15.9 inches (W) x 16.8 inches (H) x 16.7 inches (D)
Weight 19.0 kg
41.9 lbs
Environmental Considerations
Operating Temperature: +10°C to +35°C / +50°F to +90°F
Humidity: 30% to 80%
Feet: 0 to 10,000 Feet
Storage Temperature: -20°C to +60°C / -4°F to +140°F
Humidity: 10% to 90%
Feet: 0 to 45,000 Feet

NOTE: Technical specifications are subject to change without notice.




10
Features
Flat Aperture Grille CRT: Delivers an unparalleled viewing experience with a
virtually flat image, eliminating distortion and reducing glare so that what you
see on-screen is what you get on your printed output. The striped phosphor
alignment of the CRT delivers superior vertical definition with improved bright-
ness for more uniform image contrast.
OptiClear® Screen Surface: Reduces reflection and glare and increases contrast
without sacrificing focus level, clarity or brightness. Along with the flat square
technology CRT, a high contrast screen with 0.25 mm grille pitch delivers crisp,
clean text and graphics.
Dual Dynamic Beam Focus: Provides precise, continuous focus adjustments of the
electron beams and optimum image quality, even to the far edges of the screen.
AccuColor® Control System: Allows you to change between five color settings on
your display to match your personal preference.
OSMTM (On-Screen Manager) Controls: Allows you to quickly and easily adjust
all elements of your screen image via simple to use on-screen menus.
ErgoDesign® Features: Enhances human ergonomics to improve the working
environment, protect the health of the user and save money. Examples include
OSM controls for quick and easy image adjustments, tilt/swivel base for pre-
ferred angle of vision and compliance with MPRII guidelines for lower emissions.
Plug and Play: The Microsoft® solution with the Windows®95/98 operating
system facilitates setup and installation by allowing the monitor to send its
capabilities (such as screen size and resolutions supported) directly to your
computer, automatically optimizing display performance.
IPMTM (Intelligent Power Manager) System: Provides innovative power-saving
methods that allow the monitor to shift to a lower power consumption level when
on but not in use, saving two-thirds of your monitor energy costs, reducing
emissions and lowering the air conditioning costs of the workplace.
Reduced Magnetic FieldTM Technology: Reduces magnetic and alternating electric
field emissions and static electricity, addressing ergonomic concerns regarding
potential risks from extended computer monitor use.
Multiple Frequency Technology: Automatically adjusts monitor to the display
card's scanning frequency, thus displaying the resolution required.
FullScanTM Capability: Allows you to use the entire screen area in most resolu-
tions, significantly expanding image size.
OSM Display Screen Copyright 1999 by NEC Technologies, Inc.




11
Troubleshooting
No picture
· Display card should be completely seated in its slot.
· Power Button and computer power switch should be in the ON position.
· Signal cable should be completely connected to display card/computer.
· Check connector for bent or pushed-in pins.
Image is scrolling or unstable
· Signal cable should be completely attached to the computer.
· Check pin assignments and signal timings of the monitor and your
display card with respect to recommended timings and pin assignments.
· If the Macintosh cable adapter is used, check for proper connection or
make sure the display card is Macintosh compatible and that the card is
properly seated in the computer.
LED on monitor is not lit (no green, orange, yellow color can be seen)
· Power Switch should be in the ON position and power cord should
be connected.
Picture is fuzzy or color looks blotchy
· Adjust Brightness and Contrast Controls.
· Access the Degauss Control through OSMTM controls. Activate the
Degauss Control.
CAUTION: A minimum interval of 20 minutes should elapse before the
Deguass Control is used a second time when not switching
between modes.
Picture bounces or a wavy pattern is present
in the picture
· Move electrical devices that may be causing electrical interference away
from the monitor.
· See inside cover of User's Manual for FCC information.
Edges of the display image are not square
· Use the OSM Geometry Controls to straighten the edges.
· If possible, position the front of the monitor facing east.
Display image is not centered, too small, or too large
· Use the OSM Size and Position Controls to adjust the image.
Thin lines appear on your screen
· Thin lines are normal for an aperture grille CRT and are not a malfunction.
These are shadows from the damper wires used to stabilize the aperture
grille and are most noticeable when the screen's background is light
(usually white).




12
References
· BBS (978) 742-8706
NEC Technologies' Remote Bulletin Board System is an electronic service
accessible with your system and a modem. Communication parameters
are: 300/1200/2400/9600/14.4k/28.8k bps, no parity, 8-data bits,
1 stop bit
· Customer Service/
Technical Support (800) 632-4662
Fax (978) 742-7049
· Electronic Channels:
Internet e-mail: [email protected]
Internet ftp site: ftp.nectech.com
World Wide Web: http://www.nectech.com
Product Registration: http://www.nectech.com/productregistration
Windows® 95/98 INF File: http://cssweb.nectech.com/common/drivers.htm
then download the file NECMSINF.ZIP.
· FastFactsTM Information (630) 467-4363
INFORMATION DESCRIPTION DOCUMENT #
Glossary Definition of terms related 900203
to functions, features and
installation of the
MultiSync monitor
More Information Names and addresses of 900204
other groups involved in
standards and features of
the MultiSync monitor
Macintosh Connection Detailed information on 153006
connecting the MultiSync
monitor to a Macintosh
Healthy Work Environment Detailed information on 900108
setting up a healthy work
environment
· Literature & Sales Info (800) NEC-INFO [(800) 632-4636]
· MultiSync Fulfillment (800) 820-1230
[For software & accessories]
· TeleSales (800) 284-4484




13
Limited Warranty
NEC Technologies, Inc. (hereinafter "NECTECH"), warrants this Product to be free from
defects in material and workmanship and, subject to the conditions set forth below, agrees
to repair or replace (at NECTECH's sole option) any part of the enclosed unit which proves
defective for a period of three (3) years from the date of first consumer purchase. Spare parts
are warranted for ninety (90) days. Replacement parts or units may be new or refurbished and
will meet specifications of the original parts or unit.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state. This warranty is limited to the original purchaser of the Product and is not
transferable. This warranty covers only NECTECH-supplied components. Service required as
a result of third party components is not covered under this warranty. In order to be covered
under this warranty, the Product must have been purchased in the U.S.A. or Canada by the
original purchaser. This warranty only covers Product distribution in the U.S.A. or Canada by
NECTECH. No warranty service is provided outside of the U.S.A. or Canada. Proof of
Purchase will be required by NECTECH to substantiate date of purchase. Such proof of
purchase must be an original bill of sale or receipt containing name and address of seller,
purchaser, and the serial number of the product.
It shall be your obligation and expense to have the Product shipped, freight prepaid, or
delivered to the authorized reseller from whom it was purchased or other facility authorized
by NECTECH to render the services provided hereunder in either the original package or a
similar package affording an equal degree of protection. All Products returned to NECTECH
for service MUST have prior approval, which may be obtained by calling 1-800-632-4662.
The Product shall not have been previously altered, repaired, or serviced by anyone other
than a service facility authorized by NECTECH to render such service, the serial number
of the product shall not have been altered or removed. In order to be covered by this warranty
the Product shall not have been subjected to displaying of fixed images for long periods of
time resulting in image persistence (afterimage effects), accident, misuse or abuse or operated
contrary to the instructions contained in the User's Manual. Any such conditions will void this
warranty.
NECTECH SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL,
OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NECTECH
PRODUCT OTHER THAN THE LIABILITY STATED ABOVE. THESE WARRANTIES ARE IN LIEU OF
ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE
LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
This Product is warranted in accordance with the terms of this limited warranty. Consumers
are cautioned that Product performance is affected by system configuration, software, the
application, customer data, and operator control of the system, among other factors. While
NECTECH Products are considered to be compatible with many systems, specific functional
implementation by the customers of the Product may vary. Therefore, suitability of a Product
for a specific purpose or application must be determined by consumer and is not warranted
by NECTECH.
For the name of your nearest authorized NECTECH service facility, contact NECTECH
at 1-800-632-4662.

14
TCO'99
Congratulations! You have just purchased a TCO'99 approved and
labeled product! Your choice has provided you with a product devel-
oped for professional use. Your purchase has also contributed to
reducing the burden on the environment and also to the further
development of environmentally adapted electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encourag-
ing the adaptation of goods and services to the environment. The main problem, as far as
computers and other electronics equipment are concerned, is that environmentally harmful
substances are used both in the products and during the manufacturing. Since it has not been
possible for the majority of electronics equipment to be recycled in a satisfactory way, most
of these potentially damaging substances sooner or later enter Nature.
There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (Internal) and natural (external) environments.
Since all methods of conventional electricity generation have a negative effect on the
environment (acidic and climate-influencing emissions, radioactive waste, etc.), it is vital to
conserve energy. Electronics equipment in offices consume an enormous amount of energy
since they are often left running continuously.

What does labelling involve?
This product meets the requirements for the TCO'99 scheme which provides for international and
environmental labelling of personal computers. The labelling scheme was developed as a joint
effort by the TCO (The Swedish Confederation of Professional Employees), Svenska
Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet
(The Swedish National Energy Administration).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of
electrical and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands concern restrictions on the presence and use of heavy metals,
brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other
things. The product must be prepared for recycling and the manufacturer is obliged to have an
environmental plan which must be adhered to in each country where the company implements its
operational policy. The energy requirements include a demand that the computer and/or display,
after a certain period of inactivity, shall reduce its power consumption to a lower level in one or
more stages. The length of time to reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the reduction
of electric and magnetic fields, physical and visual ergonomics and good usability.

Environmental Requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn,
they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of
flame retardant substances. Most flame retardants contain bromine or chloride and these are
related to another group of environmental toxins, PCBs, which are suspected to give rise to severe
health effects, including reproductive damage in fisheating birds and mammals, due to the bio-

15
TCO'99 cont.
accumulative* processes. Flame retardants have been found in human blood and researchers fear
that disturbances in foetus development may occur.
TCO'99 demand requires that plastic components weighing more than 25 grams must not contain
flame retardants with organically bound chlorine and bromine. Flame retardants are allowed in
the printed circuit boards since no substitutes are available.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the
nervous system and in higher doses, causes lead poisoning.
TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed.
Cadmium**
Cadmium is present in rechargeable batteries and in the colourgenerating layers of certain
computer displays. Cadmium damages the nervous system and is toxic in high doses.
TCO'99 requirement states that batteries, the colourgenerating layers of display screens and the
electrical or electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches, Mercury damages the nervous system
and is toxic in high doses.
TCO'99 requirement states that batteries may not contain any Mercury. It also demands that no
mercury is present in any of the electrical or electronics components associated with the display unit.
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and
thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of
ultraviolet light with consequent increased risks of skin cancer (malignant melanoma).
The relevant TCO'99 requirement; Neither CFCs nor HCFCs may be used during the manufacturing
and assembly of the product or its packaging.

*Bio-accumulative is defined as substances which accumulate within living organisms.
**Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
To obtain complete information on the environmental criteria document, order from:
TCO Development Unit
SE-114 94 Stockholm
SWEDEN
FAX Number: +46 8 782 92 07
E-mail (Internet): [email protected]
You may also obtain current information on TCO'99 approved and labelled products by
visiting their website at: http://www.tco-info.com/




16
Röntgenstrahlung
Die in diesem Gerät erzeugten Röntgenstrahlen sind durch die eigensichere Kathodenstrahlröhre
ausreichend abgeschirmt.
Unsachgemäße Eingriffe, insbesondere Verändern der Hochspannung oder Einbau eines
anderen Bildröhrentyps, können dazu führen, daß Röntgenstrahlung in erheblicher Stärke
auftritt. So veränderte Geräte entsprechen nicht mehr dieser Zulassung und dürfen nicht
betrieben werden.




17
AVERTISSEMENT
AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION, NE PAS EXPOSER CET APPAREIL À LA PLUIE OU À
L'HUMIDITÉ. NE PAS UTILISER LA FICHE D'ALIMENTATION POLARISÉE AVEC UNE PRISE DE CORDON DE RALLONGE
OU AUTRE PRISE SAUF SI LES BROCHES PEUVENT ÊTRE ENTIÈREMENT INTRODUITES.
NE PAS OUVRIR LE BOÎTIER, LEQUEL CONTIENT DES COMPOSANTS À HAUTE TENSION. CONFIER TOUS TRAVAUX
À DU PERSONNEL TECHNIQUE QUALIFIÉ.


ATTENTION
RISQUE DE DÉCHARGE ÉLECTRIQUE · NE PAS OUVRIR
ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCUTION, NE PAS OUVRIR LE COUVERCLE (L'ARRIÈRE). À L'INTÉRIEUR, AUCUNE
PIÈCE NE NÉCESSITE L'INTERVENTION DE L'UTILISATEUR. EN CAS DE PROBLÈME, S'ADRESSER À DU PERSONNEL TECHNIQUE QUALIFIÉ.
Ce symbole est une mise en garde contre les risques d'électrocution que présentent certaines parties dépourvues
d'isolation à l'intérieur de l'appareil. Il est donc dangereux d'établir le moindre contact avec ces parties.

Ce symbole prévient l'utilisateur que des directives d'utilisation et de maintenance de cet appareil sont fournies avec
ce guide d'utilisateur. Par conséquent, celles-ci doivent être lues attentivement pour éviter tout incident.



Déclaration de conformité ­ Département des Communications du Canada
DOC : Cet appareil numérique de classe B respecte toutes les exigences du Règlement
sur le matériel à l'origine d'interférences du Canada.
C-UL : Ce produit porte la marque «C-UL» et se conforme aux règlements de sûreté
canadiens selon CAN/CSA 22.2 No. 950.

Informations FCC
1. Utiliser les câbles spécifiés fournis avec le moniteur couleur N9705 afin de ne pas provoquer d'interférences
avec la réception radio et télévision.
(1) Prière d'utiliser le câble d'alimentation fourni ou équivalent pour assurer la conformité FCC.
(2) Priére d'utiliser le câble de signal captif.
L'utilisation d'autres câbles et adaptateurs peut provoquer des interférences avec la réception radio et
télévision.
2. Cet appareil a été testé et s'avère conforme avec les spécifications d'équipements de Classe B, section 15 de
la réglementation FCC. Ces spécifications ont été établies pour garantir une protection raisonnable contre les
interférences nuisibles dans une installation résidentielle. Cet appareil génère, utilise et peut émettre des
fréquences radio et, s'il n'est pas installé et utilisé selon les directives de ce guide, il peut perturber les
communications radio. Cependant, il n'est pas garanti qu'aucune interférence ne se produira dans une
installation donnée.
Si cet appareil provoque des interférences nuisibles à la réception radio ou télévision, ce que vous pouvez
déterminer en allumant et en éteignant l'appareil, essayez de remédier au problème en prenant une ou
plusieurs des mesures suivantes :
· Réorienter ou repositionner l'antenne de réception.
· Augmenter la distance entre l'appareil et le récepteur.
· Connecter l'appareil à une prise de courant sur un circuit différent de celui sur lequel le récepteur
est connecté.
· Consulter son revendeur ou un technicien radio/TV pour obtenir de l'aide.
Si nécessaire, l'utilisateur doit contacter le revendeur ou un technicien radio/TV afin d'obtenir des informations
supplémentaires. L'utilisateur peut se procurer le livret utile suivant, préparé par la Federal Communications
Commission : «How to Identify and Resolve Radio-TV Interference Problems» (Comment cerner et résoudre les
problèmes d'interférences radio/TV). Ce livret est disponible auprès du U.S. Government Printing Office,
Washington, D.C., 20402, Stock No. 004-000-00345-4.




18
Contenu
Votre produit peut être enregistré sur Internet à l'adresse
http://www.nectech.com/productregistration
La boîte* de votre nouveau moniteur NEC Technologies MultiSync®
FE700MC contient :
· Moniteur MultiSync FE700 avec socle inclinable/rotatif
· Cordon d'alimentation
· Câble de signal captif
· Guide de l'utilisateur




Câble de signal captif




Guide de l'utilisateur Cordon d'alimentation



* Ne pas oublier de conserver la boîte et le matériel d'emballage d'origine pour trans-
porter ou expédier le moniteur.

19
Mise en marche rapide
Pour raccorder le moniteur MultiSync® FE700MC au système, suivre
les directives ci-après :
1. Mettre l'ordinateur hors tension.
2. Si nécessaire, installer la carte vidéo dans le système. Pour plus d'informations, se
reporter au guide de l'utilisateur de la carte vidéo.
3. Pour le PC : Connecter la mini-fiche D-SUB à 15 broches du câble de signal captif au
connecteur de la carte vidéo du système (Figure A.1). Serrer toutes les vis.
Pour le Mac : Connecter l'adaptateur de câble MultiSync FE700 Macintosh (non fourni)
au connecteur de moniteur sur le Macintosh (Figure B.1). Fixer l'extrémité de la mini-
fiche D-SUB à 15 broches du câble de signal captif à l'adaptateur de câble MultiSync
MultiSync FE700 Macintosh sur l'ordinateur (Figure B.1). Serrer toutes les vis.
REMARQUE : Pour obtenir un adaptateur de câble MultiSync FE700MC Macintosh,
appeler NEC Technologies au (800) 820-1230.
4. Pour les informations de téléchargement sur le fichier INF Windows® 95/98 pour le
moniteur MultiSync, se reporter à la section Références de ce guide.
5. Connecter une extrémité du cordon d'alimentation au moniteur MultiSync FE700 et
l'autre extrémité à la prise de courant (Figure C.1).
6. Allumer le moniteur (Figure D.1) et l'ordinateur.
REMARQUE : En cas de problème, prière de se reporter à la section Dépannage de ce
guide.




Figure A.1


20
Mise en march rapide (suite)




Figure B.1




Figure C.1




Figure D.1

21
Commandes
Les touches de commandes OSMMC (Gestionnaire à l'écran) à l'avant du moniteur
fonctionnent comme suit :
Menu principal Sous-menu
EXIT Quitte le menu OSM. Retour au menu principal OSM.

CONTROL Déplace la zone en surbrillance vers Déplace la zone en surbrillance vers
/ le haut/le bas pour sélectionner une le haut/le bas pour sélectionner une
des commandes. des commandes.

CONTROL Déplace la zone en surbrillance vers Déplace le curseur vers le + ou -
­/+ la gauche/la droite pour sélectionner pour augmenter ou diminuer la
une des commandes. valeur du réglage.

PROCEED Pas de fonction. Permet d'accéder à un sous-menu
ou d'exécuter un réglage.

RESET Rappel des paramètres usine du Rappel des paramètres usine de
menu en surbrillance. tous les réglages.
NOTA : En appuyant sur le bouton RESET dans le menu ou dans un
sous-menu, une fenêtre apparaîtra pour confirmer ou annuler cette opération.


Lorsque les commandes OSM sont activées, des icônes sont affichées au sommet du menu. Si une
flèche () est affichée dans un sous-menu, elle indique que d'autres choix sont disponibles. Pour
entrer dans un sous-menu, appuyez sur PROCEED.

Commandes de luminosité/contraste
Luminosité : Règle la luminosité de l'image générale et de l'écran d'arrière-plan.
Contraste : Règle la luminosité de l'image par rapport à l'arrière-plan.
Démagnétisation : Élimine l'accumulation de champs magnétiques parasites qui
modifieraient le balayage correct du faisceau d'électrons et affecteraient la pureté des
couleurs de l'écran, la netteté et la convergence. Lorsque cette commande est activée,
l'image saute et tremble quelque peu pendant la démagnétisation de l'écran.
Attention : Prière de laisser s'écouler un minimum de 20 minutes entre chaque
utilisation de la commande Degauss.

Commandes de format et de position
Gauche/Droite : Déplace l'image horizontalement (vers la gauche ou vers la droite).
Bas/Haut : Déplace l'image verticalement (vers le haut ou vers le bas).
Étroit/Large : Augmente ou diminue le format horizontal de l'image.
Petit/Grand : Augmente ou diminue le format vertical de l'image.




22
Commandes (suite)
Système de commande de couleurs/
Système de commande AccuColor®
Sélectionnez le réglage couleur au moyen des réglages préprogrammés 1 à 5. La barre
est remplacée par le réglage couleur initial de 1 à 5. Chaque réglage couleur
préprogrammé est exprimé en Kelvin. Si un préréglage est modifié, le message «Custom»
(au choix) s'affiche et remplace la température en Kelvin.
Rouge, vert, bleu : Augmente ou diminue la valeur des couleurs rouge, vert, bleu en
fonction de celle qui a été sélectionnée. Le changement du réglage de la couleur apparaît
à l'écran et le sens (augmentation ou diminution) du réglage est indiqué par la barre de
progression.
Commandes du menu Géométrie
Les commandes du menu Géométrie permettent de régler la courbure ou l'angle des
côtés de l'affichage.
Int/Ext (coussin) : Augmente ou diminue la courbure des côtés vers l'intérieur ou vers
l'extérieur.
Gauche/Droite (balance de la distorsion du coussin) : Augmente ou diminue la courbure
des côtés vers la gauche ou vers la droite.
Pente (distorsion de parallélogramme) : Augmente ou diminue l'inclinaison des côtés vers
la gauche ou vers la droite.
Alignement (distorsion du trapèze) : Augmente ou diminue le dessous de l'écran pour
qu'il soit le même que le dessus.
Rotation (rotation de balayage) : Fait pivoter tout l'affichage dans le sens horaire ou dans
le sens antihoraire.

Outils 1
Éliminateur de Moiré : Moiré est un motif ondulé qui peut s'afficher à l'écran de temps à
autre. Ce motif est répétitif et se superpose sous forme d'images ondulées. Ce phénomène
peut être plus prononcé avec certaines applications. Pour réduire le motif Moiré, réglez les
valeurs Horizontal et/ou Vertical à l'aide des boutons CONTROL ­/+.
Préréglage usine : Cette fonction vous permet de remettre tous les paramètres de l'OSM MC à
leur état d'origine. Une fenêtre d'alerte vous demandera de confirmer si vous désirez
rappeller tous les réglages usine. Les réglages individuels peuvent être réinitialisés en
mettant en surbrillance la commande à réinitialiser, puis en appuyant sur le bouton RESET.

Outils 2
Langage : Les menus de l'OSM sont disponibles en sept langues.
Extinction de l'OSM : Le menu de l'OSM restera actif aussi longtemps que vous
l'utiliserez. Dans le menu d'extinction de l'OSM, vous pouvez choisir le temps que mettra
l'affichage pour s'effacer après la dernière pression sur une touche. Les temps préréglés
sont de 10, 20, 30, 60 et de 120 secondes.




23
Commandes (suite)

Verrouillage de l'OSM : Cette fonction vous permet de verrouiller l'accès aux fonctions de
l'OSM sauf le contrôle du contraste et de la luminosité. En essayant d'accéder au menu
lorsqu'il est verrouillé, une fenêtre s'ouvrira à l'écran et vous indiquera que les réglages
ne sont pas accessibles. Pour verrouiller, appuyer sur les touches PROCEED et
simultanément. Pour déverrouiller, appuyer sur les touches PROCEED et simultanément.
IPMMC : Activé : Le système IPM fonctionne normalement et toutes les
étapes de sauvegarde d'énergie sont utilisées.
Désactivé : Le système IPM n'est pas utilisé.
REMARQUE : Pour les systèmes standard et les cartes graphiques, laisser les réglages
d'usine sur ENABLE.
Fréquence Verticale : si le taux de rafraîchissement est trop bas, un message apparaîtra à
cet effet. Pour plus d'informations, reportez-vous à la carte vidéo ou au manuel du
système.

Information
Mode d'affichage : Le menu mode d'affichage vous renseigne sur le mode et la fréquence
courante du moniteur.
Information Écran : Le numéro du modèle et le numéro de série y sont indiqués.




24
Usage recommandé
Consignes de sécurité et d'entretien
POUR UN FONCTIONNEMENT OPTIMAL, PRIÈRE DE NOTER
CE QUI SUIT POUR LE RÉGLAGE ET L'UTILISATION DU
MONITEUR COULEUR MULTISYNC® FE700MC :
· NE PAS OUVRIR LE MONITEUR. Aucune pièce intérieure ne nécessite l'intervention de
l'utilisateur, et l'ouverture ou la dépose des couvercles peut entraîner des risques de
décharges électriques dangereuses ou d'autres risques. Confier tous travaux à du personnel
technique qualifié.
· Ne pas renverser de liquides dans le boîtier, ni utiliser le moniteur près de l'eau.
· Ne pas introduire d'objets de quelque nature que ce soit dans les fentes du boîtier car ceux-
ci pourraient toucher des endroits sous tension dangereuse, ce qui peut provoquer des
blessures, voire être fatal, ou peut occasionner une décharge électrique, un incendie ou une
panne de l'appareil.
· Ne pas placer d'objets lourds sur le cordon d'alimentation. Un cordon endommagé peut
occasionner une décharge électrique ou un incendie.
· Ne pas placer cet appareil sur un chariot, un support ou une table inclinée ou instable, afin
d'éviter que le moniteur ne tombe, occasionnant de sérieux dommages au moniteur.
· Maintenir le moniteur éloigné des transformateurs à haute capacité, des moteurs électriques
et de tous autres dispositifs tels que des haut-parleurs ou ventilateurs externes, lesquels
peuvent créer des champs magnétiques puissants.
· Si possible, positionner le moniteur de sorte qu'il soit orienté vers l'est, afin de minimiser les
effets du champs magnétique terrestre.
· Changer l'orientation du moniteur alors que celui-ci est sous tension peut occasionner une
décoloration de l'image. Pour éviter cela, mettre le moniteur hors tension pendant
20 minutes avant de le remettre sous tension.
· Pour l'utilisation du moniteur MultiSync FE700 avec l'alimentation CA mondiale de
220-240 V, utiliser un cordon d'alimentation qui correspond à la tension de l'alimentation
fournie à la prise de courant CA. Le cordon d'alimentation utilisé doit être agréé et en
conformité avec les normes de sécurité de son pays. (Type H05VV-F à utiliser sauf au
Royaume-Uni.)
· Au Royauma-Uni, utiliser un cordon d'alimentation certifié BS avec une prise mouiée ayant
un fusible noir (SA) installé pour l'utilisation avec ce moniteur. Si un cordon d'alimentation
n'est pas fourmi avec ce moniteur, veuiller contacter votre fournisseur.
Débrancher immédiatement le moniteur de la prise murale et confier la réparation à du personnel
technique qualifié dans les cas suivants :
· Lorsque le cordon d'alimentation ou la fiche est endommagé(e).
· Si du liquide a été renversé ou des objets sont tombés à l'intérieur du moniteur.
· Si le moniteur a été exposé à la pluie ou à de l'eau.
· Si le moniteur est tombé ou le boîtier est endommagé.
· Si le moniteur ne fonctionne pas normalement en suivant les directives d'utilisation.
· Prévoir une aération suffisante autour du moniteur pour que la chaleur puisse se
dissiper correctement. Ne pas obstruer les ouvertures de ventilation ni placer le
moniteur près d'un radiateur ou autre source de chaleur. Ne rien poser sur le
moniteur.
· La fiche du cordon d'alimentation est le moyen principal de débrancher le
AVERTISSEMENT système de l'alimentation. Le moniteur doit être installé à proximité d'une prise
de courant facilement accessible.
· Manipuler avec soin lors du transport. Conserver l'emballage pour le transport.
25
Usage recommandé (suite)
LA MODIFICATION DE LA POSITION ET DU RÉGLAGE DU MONITEUR
PEUT RÉDUIRE LA FATIGUE DES YEUX, DES ÉPAULES ET DE LA NUQUE.
OBSERVER LES DIRECTIVES CI-APRÈS LORS DU POSITIONNEMENT
DU MONITEUR :
· Régler la hauteur du moniteur de sorte que le
dessus de l'écran soit au niveau ou légèrement en-
dessous du niveau des yeux. Les yeux doivent
regarder légèrement vers le bas lorsque l'on
regarde le milieu de l'écran.
· Positionner le moniteur à une distance minimale de
40 cm (16 po) et maximale de 60 cm (24 po) des
yeux. La distance optimale est de 50 cm (20 po).
· Reposer ses yeux régulièrement en regardant vers
un objet situé à au moins 6 m (20 pieds). Cligner
régulièrement.
· Positionner le moniteur à un angle de 90° par rapport aux fenêtres et autres sources de
lumière, afin de réduire au maximum les reflets et l'éblouissement. Régler l'inclinaison
du moniteur de sorte que l'éclairage du plafond ne soit pas reflété sur l'écran.
· Si une lumière réfléchie rend la vision de l'écran difficile, utiliser un filtre anti-reflet.
· Nettoyer régulièrement le moniteur. Utiliser un chiffon sans peluches et non abrasif et
une solution de nettoyage sans alcool, neutre, non abrasive ou un produit nettoyant
pour vitres pour éliminer au maximum la poussière.
· Régler les commandes de luminosité et de contraste du moniteur pour améliorer la
lisibilité.
· Utiliser un support de document placé près de l'écran.
· Positionner ce que l'on regarde le plus souvent (l'écran ou les documents de référence)
directement devant soi pour réduire au maximum les mouvements de la tête lorsque
l'on dactylographie.
· Consulter régulièrement un ophtalmologiste.
Ergonomie
Pour optimiser les avantages ergonomiques, observez les directives suivantes :
· Régler la luminosité jusqu'à ce que la trame de fond disparaisse.
· Ne pas placer la commande de contrate à son réglage maximum.
· Utiliser les commandes de format et position préprogrammées avec signaux standard .
· Utiliser le réglage couleur et les commandes gauche/droite préprogrammés.
· Utiliser des signaux non entrelacés avec fréquence de rafraîchissement vertical de 75 à
120 Hz.
· Ne pas utiliser la couleur bleu primaire sur fond foncé car cela rend la lecture difficile
et peut occasionner de la fatigue oculaire en raison de contraste insuffisant.
Pour des informations plus détaillées sur l'établissement d'un environnement de travail
sain, appeler NEC au (800) 820-1230, demander le service d'information par télécopieur
NEC FastFacts au (630) 467-4363 et demander le document no 900108 ou écrire à
American National Standard for Human Factors Engineering of Visual Display Terminal
Workstations - ANSI-HFS Standard No. 100-1988 - The Human Factors Society, Inc. P.O.
Box 1369, Santa Monica, California 90406.

26
Fiche technique
Caractér. techniques Moniteur Remarques
du moniteur MultiSync® FE700MC
Tube cathodique Diagonale : 17 po Déflexion de 90°, grille de 0,25 mm,
Surface utile : 16 po à grille d'ouverture, luminophore à
Rayon : 50 000 mm persistance moyenne-courte, revêtement
d'écran écran foncée, multicouche
antistatique, et surface d'écran OptiClear®.
Signal d'entrée Vidéo : ANALOGIQUE 0,7 Vp-p/75 ohms
Sync : Sync. séparée - niveau TTL
Sync. horizontale positif/négatif
Sync. verticale positif/négatif
Sync. composite (positif/négatif) (niveau TTL)
Couleurs d'affichage Entrée analogique : Nombre illimité de couleurs Dépend de la carte vidéo utilisée.
Gamme de Horizontale : 31 kHz à 70 kHz Automatique
Synchronisation Verticale : 55 Hz à 120 Hz Automatique
Résolutions autorisées 640 x 480 @ 60 à 120 Hz Certains systèmes peuvent ne pas accepter
Résolutions basées sur les fréquences 800 x 600 @ 55 à 110 Hz tous les modes listés.
horizontales et verticales uniquement 832 x 624 @ 55 à 105 Hz
1024 x 768 @ 55 à 87 Hz ........................ NEC recommande une résolution à
1152 x 870 @ 55 à 77 Hz 85 Hz pour des performances d'affichage
1280 x 1024 @ 55 à 66 Hz optimales.
Zone d'affichage active Horizontale : 315 mm/12,4 pouces Dépend de la synchronisation du signal
(réglages d'usine) Verticale : 236 mm/9,3 pouces utilisée et ne comprend pas la zone de bord.
Zone d'affichage active 325 mm/12,8 pouces Dépend de la synchronisation du signal
(balayage complet) 246 mm/9,3 pouces utilisée et ne comprend pas la zone de bord.
Alimentation CA 100-240 V, 50/60 Hz
Tension d'alimentation 1,8 A @ 100-240 V
Dimensions 403 mm (L) x 427 mm (H) x 424 mm (P)
15,9 pouces (L) x 16,8 pouces (H) x 16,7 pouces (P)
Poids