Text preview for : Sdms51.pdf part of íåùî îò íàñ
Back to : Sdms51.pdf | Home
SDM-S51
SERVICE MANUAL
US Model Canadian Model AEP Model
SPECIFICATIONS
LCD panel Input signal format
Resolution Input signal levels
Power requirements DC input Power consumption Operating temperature
Panel type: a-Si TFT Active Matrix Picture size: 15.0 inch RGB operating frequency* Horizontal: 28 - 60 kHz Vertical: 48 - 75 Hz Horizontal: Max.1024 dots Vertical: Max.768 lines RGB video signal 0.7 Vp-p, 75 , positive SYNC signal TTL level, 2.2 k, positive or negative (Separate horizontal and vertical, or composite sync) 0.3 Vp-p, 75, negative (Sync on green) 100 - 240 V, 50 - 60 Hz, Max. 0.56A DC 12 V (supplied AC adapter) Max. 25 W 5 - 35 °C
Dimensions (width/height/depth) Display (upright): Approx. 387 × 330 × 175 mm (15 1/4 × 13 × 7 inches) (with stand) Approx. 387 × 281 × 48 mm (15 1/4 × 11 1/8 × 1 15 /16 inches) (without stand) Mass Approx. 3.7 kg ( 8 lb 3 oz) (with stand) Approx. 2.9 kg (6 lb 5 oz) (without stand) Plug & Play DDC2B Accessories See page 7. * Recommended horizontal and vertical timing condition Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 µs, whichever is larger. Horizontal blanking width should be more than 2.5 µsec. Vertical blanking width should be more than 450 µsec. Design and specifications are subject to change without notice.
TFT LCD Color Computer DISPLAY
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators. 4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 7. Check the B+ and HV to see if they are specified values. Make sure your instruments are accurate; be suspicious of your HV meter if sets always have low HV. 8. Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC Leakage. Check leakage as described right. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT540A. Follow the manufacturers' instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOMs that are suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal Parts on Set
0.15 µF
1.5 k
AC Voltmeter (0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SDM-S51(E)
2
WARNING!! NEVER TURN ON THE POWER IN A CONDITION IN WHICH THE DEGAUSS COIL HAS BEEN REMOVED. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL FOR SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED.
AVERTISSEMENT!! NE JAMAIS METTRE SOUS TENSION QUAND LA BOBINE DE DEMAGNETISATION EST ENLEVÉE. ATTENTION AUX COMPOSANTS RELATIFS À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET UNE MARQUE ! SONT CRITIQUES POUR LA SÉCURITÉ. NE LES REMPLACER QUE PAR UNE PIÈCE PORTANT LE NUMÉRO SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONT L'IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT SONT IDENTIFIÉS DANS LE PRÉSENT MANUEL. SUIVRE CES PROCÉDURES LORS DE CHAQUE REMPLACEMENT DE COMPOSANTS CRITIQUES, OU LORSQU'UN MAUVAIS FONCTIONNEMENT EST SUSPECTÉ.
SDM-S51(E)
3
POWER SAVING FUNCTION
This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption as shown below.
SDM-S51
Po wer mode Po wer consumption normal operation active off* (deep sleep)** power off
*
1 (po wer) ind or icat
25 W (max.) 3 W (max.) 3 W (max.)
green orange off
When your computer enters the active off mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. After 20 seconds, the monitor enters the power saving mode. ** deep sleep is the power saving mode defined by the Environmental Protection Agency.
SDM-S51(E)
4
AUTOMATIC PICTURE QUALITY ADJUSTMENT FUNCTION
When the monitor receives an input signal, it automatically matches the signal to one of the factory preset modes stored in the monitor,s memory to provide a high quality picture at the center of the screen. (See Appendix for a list of the factory preset modes.) For input signals that do not match one of the factory preset modes, the automatic picture quality adjustment function of this monitor automatically adjusts the picture position, phase, and pitch, and ensures that a clear picture appears on the screen for any timing within the monitor,s frequency range (horizontal: 28 60 kHz , vertical: 48 - 75 Hz ).
Consequently, the first time the monitor receives input signals that do not match one of the factory preset modes, the monitor may take a longer time than normal for displaying the picture on the screen. This adjustment data is automatically stored in memory so that next time, the monitor will function in the same way as when the monitor receives the signals that match one of the factory preset modes. In all modes as above, if the picture is adjusted, the adjustment data is stored as a user mode and automatically recalled whenever the same input signal is received.
Note While the automatic picture quality adjustment function is activated, only the (power) switch will operate.
SDM-S51(E)
5
TABLE OF CONTENTS
Section Title Page Section Title Page
1. DISASSEMBLY
1-1. 1-2. 1-3. 1-4. 1-5. Back Cabinet and TFT Panel Removal ................ Keyboard Mount Removal ................................... Inverter Mount Removal ...................................... I/F Board Removal ............................................... TFT Panel Removal .............................................. 1-1 1-2 1-3 1-4 1-5
4. EXPLODED VIEWS
4-1. Chassis ................................................................. 4-2. Packing Materials ................................................. 4-2 4-3 5-1
5. ELECTRICAL PARTS LIST ...............................
2. ADJUSTMENTS
2-1. 2-2. 2-3. 2-4. 2-5. Functional Alignment (1) ..................................... Functional Alignment (2) ..................................... Table 1&2 ............................................................ Timing Specification ............................................ W/B Alignment Procedure .................................... 2-1 2-2 2-3 2-4 2-5
3. DIAGRAMS
3-1. Circuit Boards Location ........................................ 3-1
SDM-S51(E)
6
SECTION 1 DISASSEMBLY
1-1. BACK CABINET AND TFT PANEL REMOVAL
1 Four screws (+PVTP 4x12)
2 Back cabinet
3 TFT panel
SDM-S51(E)
1-1
1-2. KEYBOARD MOUNT REMOVAL
1 Screw (+PWH 3x4) 2 Four screws (+PVTP 3x10)
3 Keyboard mount
SDM-S51(E)
1-2
1-3. INVERTER MOUNT REMOVAL
1 Two screws (+PWH 3x4)
2 Inverter cover
3 Two screws (+PWH 3x4) 5 Inverter mount 6 CN2
4 Inverter shield
6 CN1 6 CY2
SDM-S51(E)
1-3
1-4. I/F BOARD REMOVAL
1 Three screws (+PWH 3x4) 2 I/F cover 3 Two screws (+PWH 3x4) 3 Three screws (+PWH 3x4) 6 I/F board mount 5 CN201 5 CN302A 5 CN501
4 Two connector screws
SDM-S51(E)
1-4
1-5. TFT PANEL REMOVAL
2 TFT panel
1 Four screws (+PVTP 4x12)
SDM-S51(E)
1-5
SECTION 2 ADJUSTMENTS
2-1. FUNCTIONAL ALIGNMENT (1)
·Procedures of how to go to service mode.
1. Hold "C" and "B" key power on, SDM-S51 goes into service mode. 2. Press "MENU" key-----ODS display contigulation RGB Reset contigulation Color Temp. 3. Press "-" key to go to second page's late icon. 4. Press "OK" key-----service menu display. 5. Select one of features. 6. Press "MENU" key to exit OSD. 7. Power OFF then ON again, monitor go to normal mode. If you would like to enter service mode again, performing the above procedures cycle.
ANALOG 9300K 6500K 5000K CONFIGUR ATION (N/A) CHIPS SYNC SLICE (N/A) EXIT OK 2 COLO R TEMP EXIT SUB-BRIGHTNESS R G B SUB-CONTRAST R INITIAL EE PRM G B PERFORM EXIT
INITIAL EE PROM CLEAR ETI TIME 1 RGB RESET
EEPROM TEST EXIT
On Off
Note 1. N/A means "Not applied". 2. This service menu only provides both Configuration & Sync slice functions. This other were used for design engineering. There is no guarantee of using those N/A functions.
SDM-S51(E)
2-1
2-2. FUNCTIONAL ALIGNMENT (2)
This paper documents the functional alignment (Used Color meter) procedure of Sony LCD monitor SDM-S51. · Equipm ent PC workstation with Windows 95 Installed PS/2 mouse is required Software: KSi Engineering alignment software tool Color meter: Option Signal generator: Option Cable: Special RS232 interface cable · Setup 1. Copy ECS software into a new PC directory. 2. Prepare timing & pattern data for signal generator according to Sony's timing specifications. 3. Prepare timing files for . 4. Connect monitor interface cable between flat panel monitor and PC com port. 5. Connect monitor video cable to signal generator. 6. Put Topcon 50cm from the monitor; Point it perpendicularly at the center of the display; Achieve the best focus through the eyepiece. 7. Enclose the monitor and Topcon in a light-shield chamber. 8. Set up [SERVICE MODE] of the monitor. · Download In order to enhance productivity, a software utility is provided to download default data to LCD monitor. The default data includes color balance data and geometry timing data. Computer: · Operation 1. Execute software . 2. Click on `Setup' menu. 3. Select `Monitor' type as `Sony SDM-S81 '. 4. Select `COM PORT' according to hardware connection. 5. Click to save the new setup configuration. 6. Quit this application and Re-enter to make the new settings effective. · On Screen Adj ustment 1. Click on the `Monitor' icon; an virtual monitor panel would show up. 2. On entry, the software tries to establish a communication link with the monitor. The monitor internal DACs are read and shown on screen sliders. A `CONNECT' icon would show up on the lower left corner of the dialog screen. 3. An error message would pop up should communication fail. A `BREAK' icon would show up on the dialog screen. If this happens, check the hardware setup, communication cable, and the connection. · Warm up time Allow 30 minutes warm up time before doing any adjustment. · Color Adjustm ent 1. 9300K color adjustment --Center adjustment-a. Click `Color Temperature' as `9300'. b. Apply 40% IRE white video field, primary mode. c. Make sure `backlight' register data is 0 (100%).
SDM-S51(E) 2-2
d. Click `Refresh'. Refer to table 1 for default data for color adjustment. e. Adjust `sub_brt_B' to achieve color temperature. Refer to table 2 for specification. f. Click `Save this color' for a 9300K color save. 2. 5000K color adjustment a. Click `Color Temperature' as `5000'. b. Repeat alignment procedure as 9300 steps b-f. 3. 6500K color adjustment a. Click `Color Temperature' as `6500'. b. Repeat alignment procedure as 9300 steps b-f. · Geometry Adjus tment 1. Connect the personal computer which has alignment data. 2. Click `Refresh' (inside Geometry Register Box). 3. Adjust `Pitch' for optimum screen performance. 4. Adjust `Phase' for optimum screen performance. 5. Adjust `H position' to make the screen center horizontally. 6. Adjust `V position' to make the screen center vertically. 7. Repeat steps 3-6 for best picture performance. 8. Click `Save Geometry' to perform a user timing mode save. 9. Repeat step 1-7 for each of the user present timings.
2-3. TABLE1 & 2
Table 1: Default data for analog color adjustment Color Brightness (G) Contrast (G) Sub-Brt-R Sub-Brt-G Sub-Brt-B Sub-Cont-R Sub-Cont-G Sub-Cont-B 9300K 50 70 30 32 26 128 128 128 6500K 30 70 33 32 18 128 128 128 5000K 50 70 37 32 12 128 128 128
Table 2: Specifications for color adjustment Color 9300 6500 5000 Tole x 0.2838 0.3132 0.3450 ± 0.003 y 0.2981 0.3297 0.3580 Y (35% IRE) 10 nit 10 nit 10 nit
± 0.003 ± 0.7 Y: Luminance measurements are in cd/m 2
SDM-S51(E)
2-3
2-4. TIMING SPECIFICATION
PRESET MODE SIGNAL MODE RESOLUTION DOT CLOCK HORIZONTAL H. TOATL H. SYNC H. BP H. ACTIV VERTICAL V. TOTAL V. SYNC V. BP V. ACTIV H/V POLARITY MODE 1 VESA 60Hz 640 X 480 25.175 MHz usec 31.778 3.813 1.907 25.422 msec 16.683 0.064 1.049 15.253 N/N MODE 2 MAC 13" 640 X 480 30.240 MHz usec 28.571 2.116 3.175 21.164 msec 15.000 0.086 1.114 13.714 N/N MODE 3 VESA 75Hz 640 X 480 31.500 MHz usec 26.667 2.032 3.810 20.317 msec 13.333 0.080 0.427 12.800 N/N MODE 4 VESA 85Hz 640 X 480 36.000 MHz usec 23.111 1.556 2.222 17.778 msec 11.764 0.069 0.578 11.093 N/N MODE 5 VESA 70Hz 720 X 400 28.350 MHz usec 31.746 2.540 3.175 25.397 msec 14.254 0.095 1.079 12.698 N/P MODE 6 VESA 60Hz 800 X 600 40.000 MHz usec 26.400 3.200 2.200 20.000 msec 16.579 0.106 0.607 15.840 P/P MODE 7 VESA 75Hz 800 X 600 49.500 MHz usec 21.333 1.616 3.232 16.162 msec 13.333 0.064 0.448 12.800 P/P MODE 8 VESA 85Hz 800 X 600 56.250 MHz usec 18.631 1.138 2.702 14.222 msec 11.756 0.056 0.503 11.179 P/P
PRESET MODE SIGNAL MODE RESOLUTION DOT CLOCK HORIZONTAL H. TOATL H. SYNC H. BP H. ACTIV VERTICAL V. TOTAL V. SYNC V. BP V. ACTIV H/V POLARITY
MODE 9 PMAC 16" 832 X 624 57.285 MHz usec 20.110 1.117 3.910 14.524 msec 13.413 0.060 0.744 12.549 N/N
MODE 10 VESA 60Hz 1024 X 768 65.000 MHz usec 20.677 2.092 2.462 15.754 msec 16.666 0.124 0.600 15.880 N/N
MODE 11 VESA 70Hz 1024 X 768 75.000 MHz usec 17.707 1.813 1.920 13.653 msec 14.272 0.106 0.513 13.599 N/N
MODE 12 VESA 75Hz 1024 X 768 78.750 MHz usec 16.660 1.219 2.235 13.003 msec 13.328 0.050 0.466 12.795 P/P
MODE 13 VESA 75Hz 1024 X 768 94.500 MHz usec 14.561 1.016 2.201 10.836 msec 11.765 0.044 0.524 11.183 P/P
MODE 14 PMAC 19" 1024 X 768 80.000 MHz usec 16.600 1.200 2.200 12.800 msec 13.346 0.050 0.498 12.749 N/N
MODE 15 MAC 1152 X 870 100.000 MHz usec 14.560 1.280 1.440 11.520 msec 13.322 0.048 0.568 12.667 N/N
MODE 16 WS 1152 X 900 92.940 MHz usec 16.182 1.377 2.087 12.395 msec 15.163 0.065 0.502 14.564 N/N
SDM-S51(E)
2-4
PRESET MODE SIGNAL MODE RESOLUTION DOT CLOCK HORIZONTAL H. TOATL H. SYNC H. BP H. ACTIV VERTICAL V. TOTAL V. SYNC V. BP V. ACTIV H/V POLARITY
MODE 17 WS 1152X 900 105.590 MHz usec 13.941 0.909 1.970 10.910 msec 13.146 0.112 0.460 12.547 N/N
MODE 18 VESA 60Hz 1280 X 960 108.000 MHz usec 16.667 1.037 2.889 11.852 msec 16.667 0.050 0.600 16.000 P/P
MODE 19 VESA 85Hz 1280 X 960 148.500 MHz usec 22.636 1.077 1.508 8. 620 msec 11.764 0.035 0.547 11.171 P/P
MODE 20 VESA 60Hz 1280 X 1024 108.000 MHz usec 15.630 1.037 2.296 11.852 msec 16.661 0.047 0.594 16.005 P/P
MODE 21 VESA 75Hz 1280 X 1024 135.000 MHz usec 12.504 1.067 1.837 9.481 msec 13.329 0.038 0.475 12.804 P/P
MODE 22 VESA 85Hz 1280 X 1024 157.500 MHz usec 10.971 1.016 1.422 8.127 msec 11.761 0.033 0.483 11.235 P/P
SDM-S51(E)
2-5
2-5. W/B ALIGNMENT PROCEDURE
A. Measurement Condition: - Measurement point: Center of screen - Measurement distance: 50 cm - Measurement Angle: 90Åã
B. Measurement equipment: - Color Analyzer: Minolta CS-1000 or equivalent - Signal Generator: VG-828D or equivalent
C. Alignment Procedure: Alignment Procedure 1. Aging: more than 30 minutes 2. Enter to "Service Mode" 3. RGB reset 4. Initial Data Setting: Parameter Setting & Specification Burn-in mode: press "BRT"+"OK" then "Power ON" Service mode: press " "+" " then "Power ON"
MaintainConfigurationRGB Reset S51: a. Brightness: 50 b. Contrast: 70 c. Sub-BRT (R/G/B): 128 d. Sub-CONT (R/G/B): 50 S81: a. Brightness: 50 b. Contrast: 70 c. Sub-BRT (R/G/B): 26 d. Sub-CONT (R/G/B): 128 30 IRE (1280*1024, 80K/75Hz) 6500K 0.3132 0.3297 10 5000K Tolerance
5. Input gray raster pattern 6. Adjust White Balance (9300K, 6500K & 5000K) and Luminance (10 nits @ SONY CS-1000) by Sub-BRT Remark: In normally, adjust G for Luminance (Y), adjust R for x and adjust B for y. 7. All mode recall
35 IRE (1024*768, 60K/75Hz) 9300K x y Y Select OSD "ALL RESET" function 0.2838 0.2981 10
0.3450 }0.003 0.3580 }0.003 10 }0.7 All mode recall: press"CONTRA ST"+"OK" then "Power ON"
SDM-S51(E)
2-6
SECTION 3 DIAGRAMS
3-1. CIRCUIT BOARDS LOCATION
Keyboard mount I/F mount
Inverter mount
SDM-S51(E)
3-1
SECTION 4 EXPLODED VIEWS
· Items with no part number and no description are not stocked because they are seldom required for routine service. · The construction parts of an assembled part are indicated with a collation number in the remark column. · Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
The components identified ! marked are critical for safety. Replace only with the part number specified.
Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
SDM-S51(E)
4-1
4-1. CHASSIS
PWH3 x 4
REF.NO. PART NO. 1
3
PWH 3x4
DESCRIPTION BEZEL ASSY(WHITE) BEZEL ASSY(BLACK) LCD PANEL I/F BOARD MOUNT KEYBOARD MOUNT INVERTER MOUNT STAND ASSY(WHITE) STAND ASSY(BLACK) COVER, REAR(WHITE) COVER, REAR(BLACK)
REMARK
PWH3 x 4
2
PWH 3x4 PWH 3x6 PVTP 3 x 10 PWH 3x4
2 3 4 5 6 7
4-087-927-01 4-087-930-01 1-904-691-11 1-761-556-11 1-761-554-11 1-761-549-11 4-087-928-01 4-087-931-01 4-087-919-01 4-087-920-01
5 4
B2.6 x 5
8
6
PSW4 x 10
4-087-926-01 CABINET ASSY(WHITE) 4-087-929-01 CABINET ASSY(BLACK)
PVTP4 x 12
7 1
8
K3 x 8
9
PTP3 x 8 P4 x 10
SDM-S51(E)
4-2
4-2. PACKING MATERIALS
REF.NO. PART NO. 51 52 53 54 55 4-087-213-01 4-087-768-01 4-087-767-01 4-087-766-01 1-477-228-11 1-477-231-11 1-765-719-11 1-765-719-21 1-765-720-11 1-765-720-21 1-757-371-11 1-757-371-21
DESCRIPTION INDIVIDUAL CARTON CUSHION (LEFT) CUSHION (RIGHT) CUSHION (BOTTOM) ADPTOR, AC(WHITE) ADPTOR, AC(BLACK)
REMARK
55 56 57 58 59 52
56
53
57
CORD SET, POWER(BLACK)(AEP) CORD SET, POWER(WHITE)(AEP) CORD SET, POWER(BLACK)(U/C) CORD SET, POWER(WHITE)(U/C) CABLE ASSY(HD15X2)(WHITE) CABLE ASSY(HD15X2)(BLACK)
54
58 59
1-772-979-21 DISC, INFORMATION(CD-ROM) 4-087-260-11 MANUAL, INSTRUCTION
51
SDM-S51(E)
4-3
SECTION 5 ELECTRICAL PARTS LIST
NOTE:
The components identified ! marked are critical for safety. Replace only with the part number specified.
Les composants identifiés par la marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
· Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. RESISTORS · All resistors are in ohms · F : nonflammable
When indicating parts by reference number, please include the board name. The components identified by [ in this manual have been carefully factory-selected for each set in order to satisfy regulations regardin X-ray radiation.Should replacement be required, replace only with the value originally used. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted.
SDM-S51(E)
5-1
*:INVERTER BOARD
No. 1 2 # Board A* B** FUSE IC Type ! /* Ref.No. F201 IC302 Part No. 1-576-633-11 6-801-646-01 Descrption W78E62B-40 Remarks-1 Remarks-2
**:I/F MOUNT
Difference
SDM-S51(E)
5-2
9-978-721-01
English 2001LL08-Data Made in Japan 2001. 12
SDM-S51(E)
69