Text preview for : Tda3826.pdf part of Philips TDA3826 Philips Quality Data Sheet
Back to : Tda3826.pdf | Home
INTEGRATED CIRCUITS
DATA SHEET
TDA3826 Single FM TV-sound demodulator circuit
Product specification File under Integrated Circuits, IC02 September 1988
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
GENERAL DESCRIPTION The TDA3826 is a single FM demodulator system with mute and 6 dB AF amplifier. Features · Supply voltage range from 4.5 V to 13.2 V · AC coupled AF stage · AF operational amplifier output with offset compensated input stage · High AF output voltage with low distortion · High ripple rejection · Low switching noise between AF and mute QUICK REFERENCE DATA PARAMETER Supply voltage (pin 11) Supply current (pin 11) VP = 5.0 V VP = 12 V FM demodulator AF output voltage (pin 5) (RMS value) Signal plus weighted-noise to weighted-noise ratio Total harmonic distortion AF switch AF output voltage (pin 12) (RMS value) THD 0.1%; Gv = 6 dB V12-1 - 1.0 (S + W)/W THD 65 - 70 0.3 f = 50 kHz; QB = 11 V5-1 - 0.5 IP IP - - 16 18 CONDITIONS SYMBOL VP MIN. 4.5 TYP. 5.0
TDA3826
MAX. 13.2 - -
UNIT V mA mA
-
V
- -
dB %
-
V
PACKAGE OUTLINE 14-lead DIL; plastic (SOT27); SOT27-1; 1996 November 27.
September 1988
2
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
TDA3826
September 1988
3
Fig.1 Block diagram.
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
RATINGS Limiting values in accordance with the Absolute Maximum System (IEC 134) PARAMETER Supply voltage (pin 11) External DC load resistance Total power dissipation Storage temperature range Operating ambient temperature range CONDITIONS SYMBOL VP RL Ptot Tstg Tamb 5 - -25 0 MIN. 4.5 -
TDA3826
MAX. 13.2 400 +125 +70 V
UNIT k mW °C °C
September 1988
4
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
TDA3826
CHARACTERISTICS VP = 5 V; Tamb = 25 °C; Vi = 10 mV; fo = 5.5 MHz; fAF = 1 kHz; f = 50 kHz; all parameters were measured with the test circuit of Fig.2; unless otherwise specified PARAMETER Supply voltage (pin 11) Total current consumption Limiting amplifier Input voltage (pin 14) (RMS value) V14-1 3 dB signal reduction DC voltages pin 2 pin 13 pin 14 Input resistance FM demodulator DC voltages pin 7 pin 8 AF output voltage (pin 5) (RMS value) AM suppression Total harmonic distortion Output impedance (pin 5) Signal plus weighted-noise to weighted-noise ratio in accordance with DIN4505; CCIR468-3 (S + W)/W (S + N)/N V5-1 R 65 75 - 40 70 80 30 45 - - - - dB dB mV dB QB = 11 V5-1 - 50 - - 0.5 - 0.3 6 - - - - V dB % k fAM = 400 Hz; m = 0.3; AM Vi = 500 µV(rms) THD Z5-1 V7-1 V8-1 - - 3.2 3.2 - - V V V2-1 V13-1 V14-1 R14-13 - - - - 2 2 2 620 - - - - V V V V14-1 - - - - 200 50 mV µV CONDITIONS SYMBOL VP Itot 4.5 - MIN. 16 TYP. 5.0 20 MAX. 13.2 UNIT V mA
Signal plus noise-to-noise ratio Bnoise = 20 kHz Residual RF signal (pin 5) (RMS value) Ripple rejection 2 × fo without de-emphasis fR = 70 Hz; VR = 100 mV(p-p)
September 1988
5
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
TDA3826
PARAMETER AF switch (pin 12) Open loop gain Noise output voltage (RMS value) Slew rate
CONDITIONS
SYMBOL
MIN.
TYP. - - -
MAX.
UNIT
GoI Bnoise = 20 kHz V12-1 V 12 1 ------------------t THD 0.1%; Gv = 6 dB V12-1
50 - 2
60 20 -
dB µV V/µs
Maximum AF output voltage (RMS value) Input impedance (pin 4) (pin 10) -1 dB small signal bandwidth DC output current Output load capacitance Feedback resistor (pin 3 to pin 12) DC output voltage AF suppression in case of mute Mute control Mute control voltage (pin 10) Input (pin 4) active input voltage input current Mute active input voltage input current input voltage input current Input voltage at pin 10 for I10 = 0 µA V10-1 - V P 0.7 -------------------2 - V V10-1 I10 V10-1 I10 0 10 2/3 VP + 0.7 -600 - - - - 1/3 VP-1 500 VP -40 V µA V µA V10-1 I10 1/3 VP -200 - - 2/3 VP-0.7 + 200 V µA see Fig.3 R3-12 V12-1 mute 0 - 70 - 2.27 76 - - - V dB Z4-1 Z10-1 Baf I12 CL 50 50 100 - - - - - - - - - - 1 500 k k kHz mA pF 1.1 - - V
September 1988
6
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
TDA3826
Fig.2 Test circuit.
September 1988
7
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
TDA3826
Fig.3 Mute control logic diagram.
September 1988
8
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
TDA3826
Fig.4 Input/output loading diagram.
September 1988
9
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
APPLICATION INFORMATION
TDA3826
Fig.5 Application diagram.
September 1988
10
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
PACKAGE OUTLINE DIP14: plastic dual in-line package; 14 leads (300 mil)
TDA3826
SOT27-1
D seating plane
ME
A2
A
L
A1
c Z e b1 b 14 8 MH w M (e 1)
pin 1 index E
1
7
0
5 scale
10 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.2 0.17 A1 min. 0.51 0.020 A2 max. 3.2 0.13 b 1.73 1.13 0.068 0.044 b1 0.53 0.38 0.021 0.015 c 0.36 0.23 0.014 0.009 D (1) 19.50 18.55 0.77 0.73 E (1) 6.48 6.20 0.26 0.24 e 2.54 0.10 e1 7.62 0.30 L 3.60 3.05 0.14 0.12 ME 8.25 7.80 0.32 0.31 MH 10.0 8.3 0.39 0.33 w 0.254 0.01 Z (1) max. 2.2 0.087
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT27-1 REFERENCES IEC 050G04 JEDEC MO-001AA EIAJ EUROPEAN PROJECTION
ISSUE DATE 92-11-17 95-03-11
September 1988
11
Philips Semiconductors
Product specification
Single FM TV-sound demodulator circuit
SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Soldering by dipping or by wave
TDA3826
The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds. DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.
September 1988
12